WAGO 750-880 Quickstart Reference

Brand: WAGO

Model: 750-880

Category: Networking

Type: Quickstart Reference

Pos: 2 /D ok ument ati on al lg em ein/E inb and/ Ei nban d H and buch - De c kblatt oh ne V ari ant enfel d ( Sta ndar d) @ 9\ mod_1285229289866_0.doc @ 64941 @ @ 1

Quickstart Reference

WAGO-I/O-SYSTEM 750

ETHERNET Programmable Fieldbus

750-880

10/100 Mbit/s; digital and analog signals

Version 1.0.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e zur D oku men tati on/I mpres sum für Stand ardh andbüc her - all g. Ang aben, An schri ften, Telef onnu mmern un d E-Mail -Adr esse n @ 3\ mod_1219151118203_21.doc @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - o hne Gli eder ung - und Ver zeic hni s @ 3\mod_1219151230875_21.doc @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 4

1.1 Validity of this Documentation ................................................................. 4

1.2 Copyright ................................................................................................... 4

1.3 Symbols ..................................................................................................... 5

1.4 Number Notation ....................................................................................... 7

1.5 Font Conventions ...................................................................................... 7

2 Important Notes ........................................................................................... 8

2.1 Legal Bases ............................................................................................... 8

2.1.1 Subject to Changes ............................................................................... 8

2.1.2 Personnel Qualifications ....................................................................... 8

2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ...... 8

2.1.4 Technical Condition of Specified Devices ........................................... 9

2.2 Safety Advice (Precautions) .................................................................... 10

3 Quickstart Description .............................................................................. 12

3.1 Hardware Design ..................................................................................... 12

3.2 Preparatory Measures .............................................................................. 16

3.2.1 Download documentation and sample projects .................................. 16

3.2.2 Installing WAGO-I/O-PRO ................................................................ 16

3.2.3 Starting Up the ETHERNET Network ............................................... 22

3.2.3.1 Determine the IP address of your PC and change it if required .... 23

3.2.3.2 Assigning an IP address to the fieldbus controller ........................ 25

3.2.3.3 Testing the ETHERNET link ......................................................... 27

3.2.4 Installing the USB Driver ................................................................... 28

4 Application example: Starterkit880_App1_FUP.pro ............................. 30

4.1 Open project ............................................................................................ 31

4.2 Configure hardware ................................................................................. 31

4.3 Main Program "PLC_PRG" .................................................................... 35

4.4 Subprogram "Blink" ................................................................................ 36

4.5 Subprogram "UserLED" ......................................................................... 38

4.6 Commissioning ....................................................................................... 42

4.6.1 Configuring a Communication Driver for an ETHERNET Link ....... 42

4.7 Configuring a Communication Driver for a USB Link .......................... 44

4.7.1 Starting the Program ........................................................................... 46

4.8 Visualization ........................................................................................... 47

4.8.1 Opening Visualization via the WAGO-I/O-PRO Software ................ 47

4.8.2 Opening Web Visualization in the Internet Browser ......................... 48

4.8.3 Operating the Visualization ................................................................ 49

List of Figures ...................................................................................................... 50

List of Tables ........................................................................................................ 52

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

4 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für alle Ser ie n/Hi nwei s z ur D oku ment ati on/ Hin weis e z ur D o kume ntati on - Ü b erschr if t 1 @ 4 \mod_1237987661750_21.doc @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /S eri e 75 0 ( WAGO- I/O- SYSTEM )/H i nwei se z ur D ok ume ntati on /Gül tig keit sber eic h D oku ment ati on K oppl er /Co ntr oller 75 0-xxxx, ohne Variantenangabe @ 4\mod_1239095911562_21.doc @ 30110 @ 2 @ 1

1.1 Validity of this Documentation

This documentation is only applicable to the 750-880 ETHERNET Programmable

Fieldbus of the WAGO-I/O-SYSTEM 750 series.

Pos: 9.1 / All e S eri en (A llg em eine M od ule) /H inw eise zur Do kum entat io n/Ur he bersc h utz a usf ührli c h @ 4 \mod_1235565145234_21.doc @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 9.2 / Do ku ment ati on all ge mein /Gl ied eru ngsel em ent e/---S eiten wech sel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 9.3 / All e S eri en (A llg em eine M od ule) /Ü bers chr ifte n für al le S eri en/H i nweis zur Dokumentation/Symbole - Über schr ift 2 @ 13\mod_1351068042408_21.doc @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 9.4. 1 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- un d s onsti ge H in weis e/G efa hr/ Gefa hr: _War nu ng vor P ers on ensc häde n al lg em ein_ - Erl äuter ung @ 13\ mod_1343309450020_21.doc @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 9.4. 2 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- un d s onsti ge H in weis e/G efa hr/ Gefa hr: _War nu ng vor P ers on ensc häde n d urc h el ektr isc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.doc @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 9.4. 3 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic herhei ts- und s ons tig e Hi nwei se/ War nu ng/W arn ung : _W arn ung vor Per son ens chäd en all ge mein_ - Erl äuter ung @ 13\ mod_1343309877041_21.doc @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 9.4. 4 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- und sonstig e Hinwei se/V orsic ht/Vor sic ht: _War nung vor Perso nensc häden allge mein_ - Erläuterung @ 13\mod_1343310028762_21.doc @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 9.4. 5 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- un d s onsti ge H in weis e/A cht ung/ Ac htung : _War nung v or Sachsc häd en allg emei n_ - Erläuterung @ 13\mod_1343310134623_21.doc @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 9.4. 6 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- un d sonsti ge Hin weise/ Acht ung/A chtung : _War nung v or Sachsc häd en durc h elektr ostati sche Aufladung_ - Erläu terung @ 13\mod_1343310227702_21.doc @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 9.4. 7 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Eräuterung @ 13\mod_1343310326906_21.doc @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 9.4. 8 / Alle Ser ien (All ge mei ne M odul e)/ Wic htig e Er l äuter ung en/ Sic her heit s- un d s onsti ge H in weis e/I nfor mat ion/ In for matio n: _W eiter e In for mati on allg emei n _ - Er läuter ung @ 13 \mod_1343310439814_21.doc @ 101051 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 9.5 / Do ku ment ati on all ge mein /Gl ied eru ngsel em ent e/---S eiten wech sel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 9. 6 /All e S eri en (A llg em eine M od ule) /H inw eise zur Do kum entat io n/Z ahl ens yste me @ 3\mod_1221059454015_21.doc @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 9.7 / All e S eri en (A llg em eine M od ule) /H inw eise zur Do kum entat io n/S chrif tko nv enti one n @ 3\mod_1221059521437_21.doc @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Programme\WAGO-I/O-CHECK

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 10 /Doku menta tion all gemei n/Gli eder ungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.doc @ 21810 @ @ 1

8 Important Notes WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 11 /Alle Ser ien (Al lge meine Mo dule)/ Übers chrif ten für alle Ser ien/ Wichti ge Erläu terung en/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.doc @ 32170 @ 1 @ 1

2 Important Notes

Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/ Einl eitu ng Wich tig e Er läut eru nge n @ 3\mod_1221059818031_21.doc @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 12.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erien /Wi chti ge Erl äuter ung en /Rec htli ch e Gr undl ag en - Ü bersc hrift 2 @ 3\ mod_1221060626343_21.doc @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 12.3 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/ Änd erung s vorbe hal t - Ü bersc hri ft 3 und I nhalt @ 3\mod_1221060036484_21.doc @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 12.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige E rläut erung en/Per son alqual ifika tion 75 0-xxxx @ 3\mod_1224061208046_21.doc @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on Series 750 devices may only be carried out by

electrical specialists with sufficient knowledge in automation. The specialists

must be familiar with the current norms and guidelines for the devices and

automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 12.5 /Serie 750 (WAGO-I/O-SYS TEM) /Wic htige Er läut erung en/Bes timm ungsg emäß e Verwen dung 7 50-xxxx @ 3 \mod_1224064151234_21.doc @ 24070 @ 3 @ 1

2.1.3 Use of the 750 Series in Compliance with Underlying

Provisions

Couplers, controllers and I/O modules found in the modular WAGO-I/O-

SYSTEM 750 receive digital and analog signals from sensors and transmit them

to the actuators or higher-level control systems. Using programmable controllers,

the signals can also be (pre-) processed.

The components have been developed for use in an environment that meets the

IP20 protection class criteria. Protection against finger injury and solid impurities

up to 12.5 mm diameter is assured; protection against water damage is not

ensured. Unless otherwise specified, operation of the components in wet and

dusty environments is prohibited.

Operating 750 Series components in home applications without further measures

is only permitted if they meet the emission limits (emissions of interference)

according to EN 61000-6-3. You will find the relevant information in the section

on "WAGO-I/O-SYSTEM 750"  "System Description"  "Technical Data" in

the manual for the used fieldbus coupler/controller.

WAGO-I/O-SYSTEM 750 Important Notes 9

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 12.6 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/T ec hnisc her Zus tan d der G erät e - Üb ers chri ft 3 un d In hal t @ 3\mod_1221060446109_21.doc @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The components to be supplied Ex Works, are equipped with hardware and

software configurations, which meet the individual application requirements.

WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in

case of changes in hardware or software as well as to non-compliant usage of

components.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 12.7 /Dokumentation allgemein/Gliederungselemente/---S eite nwec hsel --- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

10 Important Notes WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 12 .8 /All e Serie n (Allg emeine Modul e)/Ü berschr ifte n für alle S erien /Wich tige Er läuter ung en/S ic herh eitshi n weise - Üb erschr ift 2 @ 6\mod_1260180299987_21.doc @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 12.9 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/ Sich erh eits- und sons tig e Hi nw eis e/Ei nlei tung Si ch erhei ts hinw eis e H ard ware @ 6\ mod_1260180170493_21.doc @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 12.1 0. 1 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher h eits- und s ons tig e Hi nw eise /Gef ahr/ G efahr : N icht an Ger äten unt er Spa nnung ar bei te n! @ 6\mod_1260180365327_21.doc @ 46727 @ @ 1

Do not work on components while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 12.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en/ Sic her hei ts- und sonstige Hinwei se/Gefahr/Gefahr: Einbau 0750-xxxx nur in Gehäusen, Schr änken oder elektrischen Betriebsräumen! @ 6\mod_1260180556692_21.doc @ 46731 @ @ 1

Installation only in appropriate housings, cabinets or in electrical operation

rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 12.1 0. 3 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher h eits- und s ons tig e Hi nw eise /Gef ahr/ G efahr : U nfal lv erh ütung sv orsc hri ften beac ht en! @ 6\ mod_1260180657000_21.doc @ 46735 @ @ 1

Pos: 12.1 0. 4 /Al le S eri en ( Allg em ein e Mo dule) /Wich tige Er läuter ungen /Sic herh eits- un d so nsti ge Hin weis e/G ef ahr/ Gefa hr: Auf nor mg erec hten A nschl us s ach te n! @ 6\mod_1260180753479_21.doc @ 46739 @ @ 1

Pos: 12.1 1. 1 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher h eits- und s ons tige Hinweise/Achtung/Achtung: Defekte oder beschädigte Geräte aus tauschen! @ 6\mod_1260180857358_21.doc @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 12.1 1. 2 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läut erung en /Sic her heits - un d so nstig e H in weis e/Ac ht ung /Acht ung : G erä te v or kr iec he nde n un d is olier en den Stof fe n sc hütz en! @ 6\mod_1260181036216_21.doc @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 12.1 1. 3 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher h eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung: Rei nig ung nur mit zul äss ige n M ater iali en! @ 6\mod_1260181203293_21.doc @ 46751 @ @ 1

Cleaning only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 12.1 1. 4 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher h eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung: Kei n K onta kts pra y verw end en! @ 6\ mod_1260181290808_21.doc @ 46755 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 12.1 1. 5 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher hei ts- und s onsti ge Hin wei se/A cht ung /Ac htung : Verp olu ng ver mei den! @ 6\ mod_1260184045744_21.doc @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 12.1 1. 6 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er läu ter ung en/Si cher h eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung: El ektr ost atisc h e Entl ad ung ver mei de n! @ 6\mod_1260181364729_21.doc @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that you may destroy by

electrostatic discharge when you touch. Pay attention while handling the devices

to good grounding of the environment (persons, job and packing).

Pos: 13 /Doku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

12 Quickstart Description WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 14 /A ll e Ser ien ( Al lg emei ne M od ule)/ Über s chrif te n für al le S eri en/Sc hnel ls tart besc hrei bung - Üb erschr ift 1 @ 9\mod_1287492268613_21.doc @ 65713 @ 1 @ 1

3 Quickstart Description

Pos: 15 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/Fel d busko ppl er/-c ont roll er/ Einl eit end er Te xt/ Quic ks tar t/St arter Ki t 75 0-0880: Auf bau der Har dw are Ü 2 u nd Ei nl eit ung @ 1 3\mod_1348142899039_21.doc @ 103066 @ 2 @ 1

3.1 Hardware Design

The fieldbus node is to be structured as follows (viewed from left to right):

Table 3: Fieldbus Node Structure

Position

I/O-Modul

PLC ETHERNET

750-880

Digital input module

750-400

Digital output module

750-501

End module

750-600

The 24VDC power supply unit is linked to the power (24V and 0V) for the

fieldbus controller and for the power jumper contacts (see No. 5 in the figures of

the PLC views and connections below).

For the application used in the example, it is sufficient to connect a jumper

between "24V" and "+" (see No. 6) or between "0V" and "-" (see No. 9).

Figure 1: View and 24V/0V connection of the ETHERNET-TCP/IP fieldbus controller

Pos: 16 /Doku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Quickstart Description 13

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 17 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/F eldb us koppl er/- contr oll er/ Leg ende/ Ansi cht - Legende zur Ansicht SETHERNET (750-880, 881, 882) - Tabellenkopf und Nr: 1 @ 7\mod_1266415064861_21.doc @ 50950 @ @ 1

Table 4: Legend to the View ETHERNET TCP/IP Fieldbus Controller

No.

Designati

Meaning Details see Chapter:

LINK

ACT 1, 2,

MS, NS,

I/O, USR

Status LEDs Fieldbus

"Device Description" >

"Display Elements"

Pos: 18 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bung /A nsic ht/F eldb usk oppl er/-c ontr oll er/ Legen de/A nsic ht - Lege nde all g f ür K oppl er/ Contr ol ler N r: 2-13 @ 4\mod_1238495560382_21.doc @ 29458 @ @ 1

2 ---

Group marking carrier (retractable) with

additional marking possibility on two miniature

WSB markers

---

3 A, B or C Status LED’s System/Field Supply

"Device Description" >

"Display Elements"

4 --- Data Contacts

"Connect Devices" > "Data

Contacts/Internal Bus"

5 24 V, 0 V CAGE CLAMP

Connections System Supply

"Connect Devices" >

"Connecting a conductor to

the CAGE CLAMP

6 +

CAGE CLAMP

Connections Field Supply DC

24 V

"Connect Devices" >

"Connecting a conductor to

the CAGE CLAMP

7 --- Power Jumper Contact 24 V DC

"Connect Devices" >

"Power Contacts/

Field Supply"

8 --- Unlocking Lug

"Assembly" >

"Inserting and Removing

Devices"

9 - CAGE CLAMP

Connections Field Supply 0 V

"Connect Devices" >

"Connecting a conductor to

the CAGE CLAMP

10 --- Power Jumper Contact 0 V

"Connect Devices" >

"Power Contacts/

Field Supply"

11 (Earth)

CAGE CLAMP

Connections Field Supply

(Earth)

"Connect Devices" >

"Connecting a conductor to

the CAGE CLAMP

12 --- Power Jumper Contact (Earth)

"Connect Devices" >

"Power Contacts/

Field Supply"

13 --- Service Interface (open flap)

"Device Description" >

"Operating Elements"

Pos: 19 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/F eldb us koppl er/- contr oll er/ Leg ende/ Ansi cht - Leg end e Fel db usans chl uss 2 x RJ- 45 als 2-Port-ET HER NET -Switc h Nr : 1 4 @ 7\ mod_1266416127949_21.doc @ 50959 @ @ 1

14 X1, X2

Fieldbus connection 2 x RJ-45 as 2-Port

ETHERNET Switch

"Device Description" >

"Connectors"

Pos: 20 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/F eldb us koppl er/- contr oll er/ Leg ende/ Ansi cht - Leg ende für Speic herkar ten-S tec kplat z N r: 15 @ 9\mod_1286270217424_21.doc @ 65383 @ @ 1

15 --- SD card slot with cover lid

„Device Description“ >

„Operating Elements“

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/F eldb us koppl er/- contr oll er/ Leg ende/ Ansi cht - Leg ende für Verri egelu ngss chei be Nr: 16 @ 9 \mod_1286271263513_21.doc @ 65386 @ @ 1

16 --- Locking Disc

"Assembly" > "Inserting

and Removing Devices"

Pos: 22 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/F eldb us koppl er/- contr oll er/ Leg ende/ Ansi cht - Leg ende für Adress wa hlsc halt er N r: 17 @ 9\ mod_1296638222313_21.doc @ 69118 @ @ 1

17 --- Address Selection Switch

"Device Description" >

"Operating Elements"

Pos: 23 /Doku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

14 Quickstart Description WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 24 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/Fel d busko ppl er/-c ont roll er/ Einl eit end er Te xt/ Quic ks tar t 75 0-08 8x: Hin weis: Be trie bsarte nschal ter i n die ober e Stell ung sch alte n! @ 9\mod_1287492632163_21. doc @ 65716 @ @ 1

Set the operating mode switch to the top position!

Set the operating mode switch to the top position. At this setting, the firmware

and application program are executed (Activate program execution / "RUN").

The mode selector switch is located behind the cover flap (see No. 13 in the

Figure above).

Figure 2: Mode selector switch (closed and open damper of the service port)

Table 5: Mode selector switch

Number

Description

Open the damper

Operating mode switch

Pos: 25 /Doku menta tion all gemei n/Gli eder ungsel emen te/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Quickstart Description 15

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 26 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/Fel d busko ppl er/-c ont roll er/ Einl eit end er Te xt/ Quic ks tar t/St arter Ki t 75 0-0880: Speicherkarte @ 13\mod_1348217984343_21.doc @ 103159 @ @ 1

Only use recommended memory cards!

Only use the SD memory card available from WAGO (Item No. 758-879/000001)

because it is specified for industrial applications under harsh environmental

conditions and for use in the fieldbus controller.

Compatibility with other commercially available storage media cannot be

guaranteed!

Figure 3: (1) Open the memory card slot, (2) insert the SD card

Pos: 27 /D okumentation allgemei n/Glieder ung sel emen te/---Sei te nwec hsel --- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

16 Quickstart Description WAGO-I/O-SYSTEM 750

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

Pos: 28 /A ll e Ser ien ( Al lg emei ne M od ule)/ Über s chrif te n für al le S eri en/I nbetr i ebne hm en - K onfi guri eren - Par am etrier en /V orber ei tend e M aßna hm en - Ü bersc hrift 2 @ 13\mod_1348215195986_21.doc @ 103153 @ 2 @ 1

3.2 Preparatory Measures

Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/Fel d busko ppl er/-c ont roll er/ Einl eit end er Te xt/ Quic ks tar t/St arter Ki t 75 0-08 8x: D o kume ntati on un d Bei spi el proj ekt e her un terl ade n @ 13\mod_1348215563298_21.doc @ 103156 @ 3 @ 1

3.2.1 Download documentation and sample projects

Download documentation and sample projects!

Extensive documentation and sample projects for this Starterkit are available at

the WAGO homepage. You will find these at www.wago.com/startkits.

Figure 4: Download possibilities at the WAGO homepage

Pos: 30 /A ll e Ser ien ( Al lg emei ne M od ule)/ Über s chrif te n für al le S eri en/I nbetr i ebne hm en - K onfi guri eren - Par am etrier en /WA GO-I/O-P RO i ns tall ier en - Ü ber schr if t 3 @ 13\ mod_1348225656942_21.doc @ 103166 @ 3 @ 1

3.2.2 Installing WAGO-I/O-PRO

Pos: 31 /S eri e 7 50 ( WA GO-I/O-S YST EM) /Ger ät ebesc hrei bung /Ei nlei tung /Fel dbus ko ppler /-c ontr oller /Ei nl eit end er Te xt/ Quic kst art/ St arter Kit 75 0-08 8x: Lief erumf ang @ 13 \mod_1348225844857_21.doc @ 103189 @ @ 1

The Starterkit ETHERNET 750-880 includes a CD with the development

topology WAGO-I/O-PRO. This CD is also available individually under item

number 759-333.

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/Fel d busko ppl er/-c ont roll er/ Einl eit end er Te xt/ Quic ks tar t/St arter kit 75 0-0 880: Besc hrei bung - Teil 1 @ 1 3\mod_1350631197488_21.doc @ 104920 @ 34443 @ 1

WAGO-I/O-PRO is a programming and visualization tool for control programs.

This software is used to develop PLC applications for WAGO I/O SYSTEM 750

programmable fieldbus controllers. WAGO-I/O-PRO runs in compliance with the