Coway BA13-BE Owner's Instructions Manual

Coway
Brand
Coway
Model
BA13-BE
Type
Owner's Instructions Manual

This manual is also suitable for

1210964 BA13 사용설명서_수출영문_(09.03.23).indd 1 2009.3.24 10:13:3 AM
1
PRODUCT FEATURES
PRODUCT FEATURES .................................. 01
CONTENTS ....................................................01
SAFETY PRECAUTIONS ...............................02
PART NAMES .................................................07
Dimensions ..................................................07
Front / Rear view ..........................................08
Remote control .............................................08
Installation parts ...........................................09
Check before using your product .................... 10
Please keep in mind! ....................................10
Configuring a special mode .........................11
Checking the control panel .............................12
Using your bidet ..............................................15
Using the rear nozzle ...................................15
Using the front nozzle ..................................16
INSTALLING YOUR BIDET .............................17
Removing existing toilet seat ....................... 17
Installing the product ....................................17
Installing the remote control wall mount
....... 19
Cleaning and maintaining your bidet ..............2 0
Cleaning the nozzles ....................................20
Cleaning the product body ...........................20
Removing the product ..................................21
Cleaning the MESH filter .............................. 21
SPECIFICATIONS ..........................................23
TROUBLESHOOTING ....................................2 4
WARRANTY CARD .........................................2 5
1. Instant warm water system
The water is instantly heated when using the rear and front cleaning functions so that you
can immediately use water at your desired temperature.
2. Air+ function
The water stream with air bubbles provides softer, stronger cleansing.
3. MESH Filter
TheMESHlterisasemi-permanentitem.Youcanusethelterrepeatedlybycleaningit.
4. Eco mode
-Bidetecomode:Iftheseatsensordoesnotdetectsomeonesittingdownornopanelor
remote control button is pressed for approximately 10 minutes, the seat temperature is set
to ‘L’, so that power consumption is reduced. When bidet eco mode is activated, the eco
mode indicator on the front is turned on.
-Remotecontrolecomode:Ifnoremotecontrolbuttonispressedforapproximately5
seconds, the remote control display is turned off to reduce the power consumption of the
remote control battery.
BA13-AR/AE/BR/BE Common Functions
CONTENTS
5. Stainless steel twin nozzle adopted for enhanced hygiene
By adopting Stainless steel nozzles, you can use the product more hygienically. In addition,
the separation of the cleansing nozzle and the bidet nozzle ensures extra hygiene.
6. Wide Water Stream
A widely spread water stream applied to the cleaning water for smoother cleaning.
1. Wide function
Youcandirectlyselectthedegreeofspreadofthecleansingwaterfromastrongowof
watertoasoft,spread-outwaterowwhenusingrearandfrontcleansing.
2. Deodorization function
Once the seat sensor detects a person sitting, the deodorization function automatically
deodorizes odors for 1 minute. After using the bidet, the deodorization function will remain
on for 3minutes ensuring a refreshed feeling.
3. Sterilization function using oxidized silver
This bidet sterilizes the nozzle with oxidized silver sterilizing water.
Additional functions for the BA13-BR/BE
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 1 2009.3.24 10:13:5 AM
2
SAFETY PRECAUTIONS
DANGER: If not observed, serious injury or even death may occur as a result of
electrocution.
DANGER:
WARNING: If these warnings are not observed, considerable physical injury or
property damage may occur as a result of burns, electrocution, fire, or injury.
CAUTION: If these cautions are not observed, slight physical injury or property
damage may occur.
IMPORTANT SAFETYGUARDS
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING.
Save these instructions for future reference.
When using electrical products, especially when children are present, basic safety precautions
shouldalwaysbefollowed:
•
Do not use a damaged power plug or loose electric outlet. This may result in electric shock or fire.
•
Make sure to use a dedicated electrical outlet. Failing to do so may result in electric shock or fire.
•Donotmovetheproductbypullingthepowercord.Thismayresultinelectricshockorfire.
•Donothandlethepowerplugwithwethands.Thismayresultinelectricshockorfire.
•Donotforcefullybendthepowercordorplaceheavyobjectsonittopreventitfrombeing
damaged or deformed. This may result in electric shock or fire.
•Donotconnectandpulloutthepowerplugrepeatedly.Thismayresultinelectricshockorfire.
•Unplugtheproductbeforerepairing,inspecting,orreplacingparts.Failingtodosomayresult
in electric shock or fire.
•
Remove any dust or water from the power plug. Failing to do so may result in electric shock or fire.
•Donotplugtheapplianceintoanelectricaloutletorpowerstripthatisbeingusedbyseveral
other appliances. Use an electrical outlet dedicated to the product. Failing to do so may result
in fire.
•Unplugthesystemifitisnotbeingusedforalongperiodoftime.Failingtodosomayresultin
electric shock or fire.
•Donotattempttorepairormodifythepowercord.Thismayresultinelectricshockorfire.
•Ifthepowercordisdamaged,donotreplacethecordyourself.CallaCowayServiceCenterto
have it replaced. Failing to do so may result in electric shock or fire.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 2 2009.3.24 10:13:5 AM
3
SAFETY PRECAUTIONS
DANGER:
SAVE THESE INSTRUCTIONS
•Iftheproductproducesastrangenoise,aburntsmell,oremitssmoke,unplugitimmediately
from the electrical outlet and call our service center. Failing to do so may result in electric
shock or fire.
•Donotinsertawireorsharpobjectinanyproductgapsorthewarmairoutlet.Thismayresult
in electric shock, fire, or product damage.
•Donotplaceanelectricheaterneartheproductordisposeofanyburningmaterialssuchasa
lit cigarette in the toilet. This may result in fire or product deformation.
•Donotplaceanycontainersfilledwithwater,medicine,food,anymetallicobjects,orany
flammable material on top of the product. If foreign material enters the product, this may result
in electric shock or fire.
•Donotusetheproductinlocationsexposedtoexcessivemoistureanddonotsplashwater
onto the product. This may result in electric shock or fire.
•Donotusetheproductifitisnotworkingproperly.
※Pleaseunplugtheproductimmediately,andcallourservicecenterafterclosingthemain
water supply valve. Failing to do so may result in electric shock or fire.
•Whiletakingashowerorcleaningthebathroom,pullthepowerplugoutoftheelectricaloutlet
and exercise caution that water or detergent does not splash onto the bidet. Failing to do so
may result in electric shock or fire.
※Ifforeignmaterialenterstheproduct,pullthepowerplugoutoftheelectricaloutlet,turnoff
the main water valve, and call the Coway Service Center.
•Donotdroptheremotecontrol.Thismayresultinproductdamageoramalfunction.
•Donotseparatetheseatfromthebidet.Thismayresultinelectricshock,fire,orproduct
damage.
•Donotdisassemble,repair,ormodifytheproductyourself.Thismayresultinelectricshock,
fire, or product damage.
•Donotusetheproductwhilebathing.
•Donotplaceorstoretheproductwhereitcanfallorbepulledintoatuborsink.
•Donotplaceinordroptheproductintowateroranyotherliquid.
•Donotreachfortheproductifithasfallenintowater.Unplugtheproductimmediately.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 3 2009.3.24 10:13:5 AM
4
SAFETY PRECAUTIONS
WARNING:
•Donotoperateorstoretheunitinlocationswhereflammableorcombustiblematerialsare
used. This may result in electric shock or fire.
•Usemainwatersupplyasthesuppliedwater.Industrialwaterorgraywater,ifusedassupply
water may cause skin damage or disease.
•Donotblockthewarmairoutletwithyourhand.Thismayresultinburnsorfire.
•Pleaseturnoffthemainwatersupplyvalvewhencleaningthefilter.Failingtodosomayresult
in electric shock or product damage.
•Forchildren,theelderly,andthosewhocannotadjustthetemperaturethemselvesorhave
sensitive skin, set the warm water temperature and seat temperature to ‘L.’ Failing to do so
may result in low temperature burns.
※About‘lowtemperatureburns’:Thisreferstoburnsinflictedbymakingcontactwith
temperaturesaround40℃foranextendedperiodoftime).
•Donotpressthebuttonsusingexcessiveforce.Thismayresultinproductdamageora
malfunction.
•Donotstandorplaceaheavyobjectontheseatcover.Thismayresultinproductdamageor
a malfunction.
•Closesupervisionisnecessarywhenthisproductisusedbychildrenorpersonsrequiring
general assistance.
•Usethisproductforitsintendeduseonly,asdescribedinthismanual.Donotuseattachments
not recommended by the manufacturer.
•Neveroperatethisproductifithasadamagedcordorplug,ifitisnotworkingproperly,ifithas
been dropped or damaged, or dropped into water. Return the product to a service center for
examination and repair.
•Keepthecordawayfromheatedsurfaces.
•Neverblocktheairopeningsoftheproductorplaceitonasoftsurface,suchasabedor
couch,wheretheairopeningsmaybeblocked.Keeptheairopeningsfreeoflint,hair,etc.
•Neverusetheproductwhilesleepingorwhendrowsy.
•Neverdroporinsertanyobjectintoanyopeningorhose.
•Donotusetheproductoutdoorsoroperatewhereaerosol(spray)productsarebeingusedor
where it could be exposed to oxygen.
•Connectthisproducttoaproperlygroundedoutletonly.RefertotheGroundingInstructions.
•Unplugthisproductbeforefilling.Fill(reservoir)withwateronlyunlessotherwisespecifiedby
themanufacturer.Donotoverfill(orspecifyfillinginstructions).
SAVE THESE INSTRUCTIONS
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 4 2009.3.24 10:13:5 AM
5
SAFETY PRECAUTIONS
SAVE THESE INSTRUCTIONS
CAUTION:
•Donotconnectthemainwatertothehotwaterpipe.Thismayresultinamalfunctionor
accident(Makesuretoconnectittothecoldmainwatersupplypipe).
•Aftertheinstallation,makesuretocheckthewatersupplyconnectionsforleaks.Rubber
packing should be applied to the connection hose.
•Donotinstalltheairpurifierinalocationexposedtodirectsunlight.Thismayresultin
deformation or discoloration.
•Donotopen/closetheseatcoverusingexcessiveforceorleanonthecover.Thismayresultin
product damage or a malfunction or physical injury.
※Theseatcovercloses/opensslowlyusingthe‘softopening/closing’method.
•Exercisecautionthaturinedoesnotcomeintocontactwiththenozzles,airdryeroutlet,orthe
outside surface of the product. Failing to do so may result in bad odors or malfunctions.
•Iftheproductwillnotbeusedforalongperiodoftime,pullthepowerplugoutoftheelectrical
outlet, close the main water supply valve, and drain the water in the water tank.
•Donotpulloutthebidethoseorconnectionhoseusingexcessiveforce.Thismayresultina
leak or malfunction.
•Pullthepowerplugoutoftheelectricaloutletbeforecleaningtheunit.Donotsplashwater
directly onto the bidet, or use thinner, benzene, chemicals, or hydrochloric acid detergent.
This may result in corrosion to the metal parts or discoloration or scratches to the bidet body.
※Useasoftclothorspongetocleanthebidet.
•Thisapplianceisnotintendedforusebypersons[includingchildren]withreducedphysical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 5 2009.3.24 10:13:5 AM
6
SAFETY PRECAUTIONS
SAVE THESE INSTRUCTIONS
•Thisproductshouldbegrounded.Intheeventofanelectricalshortcircuit,groundingreduces
theriskofelectricshockbyprovidinganescaperoute(wire)fortheelectriccurrent.This
productisequippedwithacordconsistingofagroundingwirewithagroundingplug.The
plug must be plugged into an outlet that is properly installed and grounded.
Ifitisnecessarytouseanextensioncord,useonlyathreewireextensioncordwithathree-
bladegroundingplug,andathree-slotreceptaclethatwillaccepttheplugoftheproduct.
Replace or repair a damaged cord immediately.
•Iftherepairorreplacementofthecordorplugisnecessary,donotconnectthegrounding
wire to either flat blade terminal. The insulation wire with an outer green surface with or
without yellow stripes is the grounding wire.
•Checkwithaqualifiedelectricianorservicetechnicianifyoudonotunderstandthegrounding
instructions completely, or if in you are in doubt whether the product is properly grounded.
•Thisproductisforuseonanominal120Vcircuit,andhasa
grounding plug that looks like the plug illustrated in Figure 1.
Grounded
Outlet
Grounding
Pin
Figure 1
The improper use of the grounding plug can result in electric shock.
GROUNDING INSTRUCTIONS
Extension cord
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 6 2009.3.24 10:13:6 AM
7
411 mm
(16.2 inch)
382 mm
(15 inch)
202 mm
(7.9 inch)
350 mm
(13.8 inch)
134 mm
(5.3 inch)
140 mm ~ 210 mm
(5.5 ~ 8.3 inch)
411 mm
(16.2 inch)
382 mm
(15 inch)
202 mm
(7.9 inch)
385 mm
(15.2 inch)
134 mm
(5.3 inch)
Rear fixing distance : 164 mm (6.5 inch)
49 mm
(1.9 inch)
140 mm ~ 210 mm
(5.5 ~ 8.3 inch)
411 mm
(16.2 inch)
382 mm
(15 inch)
202 mm
(7.9 inch)
350 mm
(13.8 inch)
134 mm
(5.3 inch)
140 mm ~ 210 mm
(5.5 ~ 8.3 inch)
411 mm
(16.2 inch)
382 mm
(15 inch)
202 mm
(7.9 inch)
385 mm
(15.2 inch)
134 mm
(5.3 inch)
Rear fixing distance : 164 mm (6.5 inch)
49 mm
(1.9 inch)
140 mm ~ 210 mm
(5.5 ~ 8.3 inch)
411 mm
(16.2 inch)
382 mm
(15 inch)
202 mm
(7.9 inch)
350 mm
(13.8 inch)
134 mm
(5.3 inch)
140 mm ~ 210 mm
(5.5 ~ 8.3 inch)
411 mm
(16.2 inch)
382 mm
(15 inch)
202 mm
(7.9 inch)
385 mm
(15.2 inch)
134 mm
(5.3 inch)
Rear fixing distance : 164 mm (6.5 inch)
49 mm
(1.9 inch)
140 mm ~ 210 mm
(5.5 ~ 8.3 inch)
Dimensions
The bidet has the following dimensions.
Do not install the bidet when the dimensions of the bidet differ from those of the toilet.
>> BA13-AR/BR (Round shape)
>> BA13-AE/BE (Elongated shape)
>> Bottom view >> Distance between fixing holes
PART NAMES
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 7 2009.3.24 10:13:7 AM
8
PART NAMES
Front / Rear view
Remote control
1
Seat cover
2
Warning sticker
3
IR sensor
4
Nozzle
5
Seat sensor
6
Bidet seat
7
Water tank hose
8
Bidet hose
9
Main water supply pipe
10
Main water supply valve
11
T-shapedconnector
12
Power cord
13
Product sticker
14
Drain plug
15
Button
16
Installation plate
17
MESHlter
2
4
5
6
7
11
10
9
3
1
12
13
17
16
BA13-A
BA13-B
BA13-A
BA13-B
BA13-AR/AE BA13-BR/BE
14 15
8
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 8 2009.3.24 10:13:8 AM
9
PART NAMES
Installation parts
1
2xingscrews
2
2xingrubbers
3
2xingwashers
4
2xingnuts
5
Installation plate
6
2xingsliders
7
Rubber packing
8
T-shapedconnector
9
Bidet hose
10
Remote control wall mount
(includingthestickerfor
attachment)
11
2 screws
12
2 anchors
13
3batteries(AAA)
1
2
3
4
5
8
9
10 11 12 13
6
7
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 9 2009.3.24 10:13:9 AM
10
CHECK BEFORE USING YOUR PRODUCT
Remove the protective film from the operation part before using it.
Tips
Please keep in mind!
Open the main water supply valve.
The bidet only works normally when water is supplied.
After the installation
Check if water leaks from the main water supply valve or the connecting hose.
YoumustinserttherubberpackingbetweentheT-shapedconnectionpipeandthe
main water supply pipe.
Cleaning the filter on a regular basis
CleantheMESHfilteronaregularbasis(Thecleaningintervalmaydiffer
dependingonthewaterquility).IftheMESHfilteriscontaminatedbyforeign
substances,thefilterisblockedornon-filteredcleansingwatermaybeejected.
If the bidet has not been used for a long time
When the bidet has not been used for a long time, clean the filter and clean each part
ofthebidetsuchastheairdryeroutlet,thenozzleandtheseatbeforeuse(seep.16).
Check whether the product is in eco mode before using it.
-Iftheseatsensordoesnotdetectanyonesittingdownornopanelorremotecontrolbuttonis
pressed for approximately 10 minutes, bidet eco mode is activated, the eco mode indicator
is turned on, and the seat temperature is set to ‘L’ to reduce the power consumption of the
product.
-
When sitting down on the seat or pressing a panel button, the power indicator is turned on, the eco
mode indicator is turned off and the seat temperature returns to the last configured temperature.
-Evenifyousitdownontheseatorpressapanelbutton,thepowerindicatorisnotturned
on. This means that the power is turned off. In this case, press the power selection button to
turn the power on before using it.
Thisproductisfor120V~/60Hzonly.
Make sure to connect the power plug to a grounded electrical outlet
(120V~/60Hz)dedicatedtotheproduct.
Tips
Configure and use a special mode according to your preferences.
Youcanconfigureoneofthespecialmodes(ecomode,seatsensorlockmode,
silentmode)accordingtoyourpreferences(seep.11).
Connect the power.
Plug the power cord into the electrical outlet. The bidet only works normally when
the electricity is connected.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 10 2009.3.24 10:13:11 AM
11
CHECK BEFORE USING YOUR PRODUCT
Selecting/cancelling silent mode
1. Press and hold down the ‘Power’ and ‘Rear Cleansing’ buttons
simultaneously for at least 1 second when the power cord is plugged into
the electrical outlet (an alarm sound is generated).
2. Set the mode by pressing the ‘Power’ button on the operation part.
-Ifthepowerindicatoristurnedonthisindicatesthatsilentmodehasbeenset.
-Ifthepowerindicatoristurnedoff,thisindicatesthatsilentmodehasbeen
canceled.
3. After setting silent mode, and pressing the ‘Power’ and ‘Rear Cleansing’
buttons simultaneously or no button is pressed for 10 seconds, the
setting is saved and the bidet changes to the standby state (an alarm
sound is generated).
Conguring a special mode
Selecting/cancelling seat sensor lock mode
1. Press and hold down the ‘Power’ and ‘Rear Cleansing’ buttons
simultaneously for at least 1 second when the power cord is plugged into
the electrical outlet (an alarm sound is generated).
2. Set the mode by pressing the ‘Nozzle Cleaning’ button on the operation
part.
-Iftheseattemp.indicatoristurnedon,thisindicatesthatseatsensorlock
mode has been set.
-Iftheseattemp.indicatoristurnedoff,thisindicatesthatseatsensorlock
mode has been canceled.
3. After setting seat sensor lock mode, and pressing the ‘Power’ and
‘Rear Cleansing’ buttons simultaneously or no button is pressed for 10
seconds, the setting is saved and the bidet changes to the standby state
(an alarm sound is generated).
Selecting/cancelling bidet eco mode
1. Press and hold down the ‘Power’ and ‘Rear Cleansing’ buttons
simultaneously for at least 1 second when the power cord is plugged into
the electrical outlet (an alarm sound is generated).
2. Set the mode by pressing the ‘Rear Cleansing’ button on the operation
part.
-Iftheecomodeindicatoristurnedon,thisindicatesthatbidetecomodehas
been set.
-Iftheecomodeindicatoristurnedoff,thisindicatesthatbidetecomodehas
been canceled.
3. After selecting bidet eco mode, and you press the ‘Power’ and ‘Rear
Cleansing’ buttons simultaneously or no button is pressed for 10
seconds, the setting is saved and the bidet changes to the standby state
(an alarm sound is generated).
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 11 2009.3.24 10:13:13 AM
12
CHECKING THE CONTROL PANEL
Display Control panel
Display
Control panel
‘Power’ button
Turns the product ON/OFF.
Press and hold the button for more than
2 seconds when you turn it off.
If the ‘Power’ button is pressed while the front, rear
cleansing function is operating, the cleansing function
is stopped and the bidet changes to standby mode.
1
The ‘Nozzle Cleaning’ button
Cleans the nozzle. If you press ‘Nozzle cleaning’ button, the nozzle is extended fully,
and you can clean it conveniently.
3
‘Rear Cleansing’ button
Selects the rear cleansing function.
2
Remote control signal
receiver
This receives the signals
from the remote control.
1
1
1
1
1
1
3
2
1
1
5
Remote control signal
receiver
This receives the signals
from the remote control.
1
2
1
3
1
4
1
5
1
2
Power indicator
This indicator is turned on when the
bidet power is turned on.
This indicator is turned off when bidet eco
mode is activated.
1
3
Eco mode indicator
If you activate the eco function, this
indicator is turned on when eco mode
starts.
1
4
Seat Temperature indicator
This indicator represents the seat
temperature.
Indicatoron-L/M/H
Indicatoroff-OFF
This indicator is turned off when bidet eco
mode is activated.
※Youcanusethebasicfunctionssuchasrearcleansingandnozzlecleaningfromthebidet’scontrolpanel
without using the remote control.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 12 2009.3.24 10:13:14 AM
13
CHECKING THE CONTROL PANEL
Display Control panel
Display / Control panel
BA13-B
‘Seat Temp.’ button
‘Stop’ button
‘Water Pressure/Dry
Temp.’ button
‘Move’ button
‘Rear’ button
‘Wide’ button
‘Dry’ button
‘Front’ button
‘Water Temp.’ button
‘Deodorize’ button
‘Nozzle Position’
button
1
2
3
5
4
6
7
8
9
11
12
Remote control
signal transmitter
1
‘Sterilize’ button
10
‘Water Temp.’ indicator
‘Seat Temp.’ indicator
‘Wide’ indicator
2
3
4
FortheBA13-AR/AE,the‘Wide’,‘Sterilize’and
‘Deodorize’ are excluded.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 13 2009.3.24 10:13:14 AM
14
CHECKING THE CONTROL PANEL
‘Stop’ button
All currently operating functions will stop.
‘Nozzle Position’ button
Use this button to control the nozzle
position during the rear cleansing/front
cleansing operation. You can move
the nozzle in 5 levels using the ‘Nozzle
Position’ button.
‘Water Temp.’ button
Use this button to control the water
temperature. Whenever the ‘Water
Temp.’ button is pressed, you can control
thewatertemperaturein4levels(L M
H Off).
‘Sterilization’ button
Use this button to perform the
sterilization function. Sterilizing water is
ejected for 30 seconds to sterilize and
clean the nozzle.
‘Deodorization’ button
Use this button to perform the
deodorization function. When you press
this button, the deodorization function is
performed for approximately 1 minute.
※FortheBA13-BR/BEonly
3
7
9
11
12
※FortheBA13-BR/BEonly
Remote control signal transmitter
Transmits the signal when a remote control
button is pressed.
1
1
‘Wide’ indicator
Whenever the ‘Wide’ button is pressed,
the indicator cycles through the following
options:Straightline(Blue) Level1(Pink)
Level2(Red).
4
‘Seat Temp.’ button
Use this button to control the seat
temperature. Whenever the ‘Seat Temp.’
button is pressed. You can control the
seattemperaturein4levels(L M H
Off).
10
‘Wide’ button
Use this button to control the water
ejection range when using the cleansing
function. You can select the angle of the
water in 3 levels using the Wide function
button(StraightLine Level 1 Level2).
Whenever this button is pressed, the
Wide function indicator turns a different
color.
8
‘Move’ button
Use this button to use the move function.
If you press the ‘Move’ button, as the
nozzle is moved back and forth while
you operate the rear cleansing/front
cleansing function, you can clean a
wider area.
5
‘Dry’ button
Use this button to use the drying
function. It helps the drying process after
using the rear cleansing/front cleansing
function.
4
‘Water Pressure/Dry Temp.’ button
You can control the water pressure
in 3
levels(L M H)andcontroltheair
dryertemperaturein4levels(L M
H OFF)usingtheWater‘Pressure/Dry
Temp.’ button.
You can control the water pressure when
operating the rear cleansing/front cleansing
functions and control the air dryer temperature
when operating the drying function.
6
‘Water Temp.’ indicator
Whenever the ‘Water Temp.’ button is
pressed, the temperature control indicator
cyclesthroughthefollowingorder:
L(Blue) M(Pink) H(Red) Off.
1
2
Display
‘Seat Temp.’ indicator
Whenever the ‘Seat Temp.’ button is
pressed, the temperature control indicator
cyclesthroughthefollowingoptions:
L(Blue) M(Pink) H(Red)Off.
3
‘Rear’ button
Use this button to use the rear cleansing
function.
‘Front’ button
Use this button to use the front cleansing
function for women.
1 2
Control panel
※FortheBA13-BR/BEonly
※FortheBA13-BR/BEonly
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 14 2009.3.24 10:13:15 AM
15
USING YOUR BIDET
Using the rear nozzle
Using the rear nozzle
1. Sit down on the seat and press the ‘Rear Cleansing’ button on the operation part.
2. Self-cleaning for the rear cleansing nozzle is performed, removing the cold water remaining
inside the nozzle before the water stream is ejected so that the water can be set to a desired
temperature for cleansing.
3. The cleansing water is ejected for approximately 1 minute and then stops automatically.
4. Self-cleaning for rear cleansing nozzle is performed for approximately 5 seconds after rear
cleansing. Then the nozzle retracts itself.
5. You can adjust the nozzle position by pressing the ‘Nozzle Position’ button.
6. You can adjust the water ejection angle by pressing the ‘Wide’ button (for the BA13-BR/BE
only).
Moving
Press the ‘Move’ button on the operation part.
-Thenozzlemovesbackandforth,providingawiderrangeofcleansing.
This will operate for as long as the rear cleansing function continues.
You can control the nozzle position by pressing the ‘Nozzle Position’ button.
To stop the move function, press the ‘Move’ button once again.
Drying
Press the ‘Dry’ button on the operation part.
-Warmairisemittedforapproximately2minutes.
If you wipe off the water lightly before turning on the air dryer, drying will finish faster.
You can control the air temperature by pressing the ‘Dry Temp.’ button.
If you press the ‘Dry’ button again during the operation, additional drying starts for another 2 minutes.
If you press the ‘Dry’ button while cleansing, cleansing is stopped and drying starts immediately.
Stopping
To stop the current operation, press the ‘Stop’ button.
-Thisstopsallcurrentlyoperatingfunctions.
The drying function stops 2 seconds after the ‘Stop’ button is pressed.
The cleansing water ejection time may be delayed while the above functions are performed.
Tips
If the ‘Rear Cleansing’ button is pressed again during the cleansing operation, the rear
cleansing function operates for another 1 minute.
While cleansing, users can adjust the water temperature, water pressure, and nozzle
position according to their preferences.
You can not increase the water pressure level higher than level 2 if your area is in the
following conditions.
-Mainwatersupplytemperatureunder10℃andratedpowersourceunder110V~.
If the seat sensor does not detect a human body, the bidet will not work.
Tips
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 15 2009.3.24 10:13:15 AM
16
USING YOUR BIDET
Using the front nozzle
1. Sit down on the seat and press the ‘Front Cleansing’ button on the operation part.
2. Self-cleaning for the front cleansing nozzle is performed, removing the cold water remaining
inside the nozzle before the water stream is ejected so that the water can be set to a desired
temperature for cleansing.
3. The cleansing water is ejected for approximately 1 minute and then stops automatically.
4. Self-cleaning for rear cleansing nozzle is performed for approximately 5 seconds after front
cleansing. Then the nozzle retracts itself.
5. You can adjust the nozzle position by pressing the ‘Nozzle Position’ button.
6. You can adjust the water ejection angle by pressing the ‘Wide’ button (for the BA13-BR/BE
only).
Moving
Press the ‘Move’ button on the operation part.
-Thenozzlemovesbackandforth,providingawiderrangeofcleansing.
This will operate for as long as the front cleansing function continues.
You can control the nozzle position by pressing the ‘Nozzle Position’ button.
To stop the move function, press the ‘Move’ button once again.
Drying
Press the ‘Dry’ button on the operation part.
-Warmairisemittedforapproximately2minutes.
If you wipe off the water lightly before turning on the air dryer, drying will finish faster.
You can control the air temperature by pressing the ‘Dry Temp.’ button.
If you press the ‘Dry’ button again during the operation, additional drying starts for another 2 minutes.
If you press the ‘Dry’ button while cleansing, cleansing is stopped and drying starts immediately.
Stopping
To stop the current operation, press the ‘Stop’ button.
-Thisstopsallcurrentlyoperatingfunctions.
The drying function stops 2 seconds after the ‘Stop’ button is pressed.
Using the front nozzle
The cleansing water ejection time may be delayed while the above functions are performed.
Tips
If the ‘Front Cleansing’ button is pressed again during the cleansing operation, the front
cleansing function operates for another 1 minute.
While cleansing, users can adjust the water temperature, water pressure, and nozzle
position according to their preferences.
You can not increase the water pressure level higher than level 2 if your area is in the
following conditions.
-Mainwatersupplytemperatureunder10℃andratedpowersourceunder110V~.
If the seat sensor does not detect a human body, the bidet will not work.
Tips
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 16 2009.3.24 10:13:15 AM
17
As the bidet should be installed on the toilet, ensure that water is not splashed onto
the bidet.
There may be some water remaining inside the filter which was used to test the product
during the inspection process at the factory. This does not mean that the product was
previously used.
Tips
INSTALLING YOUR BIDET
Removing existing toilet seat
Installing the product
Cold main water supply
Make sure that the bidet is connected to the cold water pipe.
(Iftheproductisconnectedtothehotwaterpipe,thismaydamagethefilterandhose).
Caution
2. Connect the rubber packing, T-shaped connector, and water tank hose in
this order to the existing water pipe. Please connect the bidet hose to the
T-shaped connector.
Please ensure that the rubber packing is inserted between the water pipe and
theT-shapedconnector. 
FirmlytightenthenutsbelowandontopoftheT-shapedconnectoralltheway
to the end in a clockwise direction.
1. Turn off the main water supply valve ① and separate the existing water
tank hose ②.
1. Remove the existing toilet seat ① and seat cover ② by removing the fixing
nuts.
Keeptheremovedtoiletseatinashadedlocationtopreventitfrombeingdamaged.
Tips
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 17 2009.3.24 10:13:16 AM
18
INSTALLING YOUR BIDET
4. Align the back of the bidet to the installation plate and push the bidet
backwards while pressing the button to the left of the bidet. (Hold the bidet
with both hands and push it backwards until it clicks into place).
Check if the bidet moves to the left or right. If it moves, fasten the fixing nuts
again.
5. Connect the bidet hose to the side of the bidet.
Make sure that the bidet hose is firmly connected. If the main water supply valve
is opened when the hose is not connected properly, the bidet hose may become
separated and cause water to splash, resulting in injury.
Take care that the bidet hose is not excessively bent by twisting it.
6. Open the main water supply valve.
7. Connect the power cord to the electrical outlet.
Make sure to use a grounded electrical outlet. In the case of a short
circuit, grounding prevents electric shock or injury.
Make sure to use a dedicated electrical outlet with grounding
terminals.
If using an extension cord is unavoidable, use one with grounding
terminalsfor120V~/60Hzorhigher.
Caution
Installing the product
3. Place the fixing slider over the installation plate on the toilet, insert the
fixing bolts, and fasten the nuts so that the installation plate is fixed.
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 18 2009.3.24 10:13:18 AM
19
INSTALLING YOUR BIDET
Installing the remote control wall mount
1. Place the remote control wall mount over the required position on
the wall and mark the 2 points for the anchors on the wall.
2. Drill 2 holes with a depth of approximately 35 mm at the marked points.
Use a drill bit with a diameter of ∅ 6.5 mm.
3. Insert the anchors into the holes and push them all the way in.
4. Remove the 2 pieces of protective film from the back of the remote
control wall mount, and attach the mount to the wall aligning the holes
with the anchors in the wall.
5. Place the remote control into the mount as shown by the figure.
Make sure to install the remote control wall mount on the wall using the supplied screws.
Failing to do so may result in the product falling and being damaged.
If the bathroom has 3 sides in a black or similar color, use the remote control while fixing
it to the wall holder.
Failing to do so may result in the product not working properly due to the remote control
signal reception ratio being too low.
Tips
1210964 BA13 사용설명서_수출영문_(09.03.23).indd 19 2009.3.24 10:13:19 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Coway BA13-BE Owner's Instructions Manual

Coway
Brand
Coway
Model
BA13-BE
Type
Owner's Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents