American Standard T064.60X User manual

Brand: American Standard

Model: T064.60X

Category: Sanitary ware

Type: User manual

5-5/8" REF.

T064.60X

M968836 Rev.1.4

To assure proper positioning in relation to wall, note

roughing-in dimensions.

ROUGHING-IN DIMENSIONS

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

THREADED INLETS (STOPS)

INLETS

1/2" NPT

5-5/8"

1-3/4"

OUTLETS 1/2" NPT

5-5/8"

Recommended Tools

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Plumbers' Putty or Caulking

Phillips Screwdriver

1-5/8" TO 3-1/4"

BOTTOM OF

TUB

74" FOR

HEAD CLEARANCE

1/2" NPT

FINISHED WALL

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

80'' AND 86'

8-1/8" REF.

6-3/4"

1/2" NPT

1/2" REF.

18"

OPTIONAL

"SEE ILLUSTRATION"

TOP OF

TUB RIM

SHW

TUB

Pipe Wrench

BATH/SHOWER TRIM KIT WITH DIVERTER

7-1/4" D.

2-3/8"

SERIN

™

To ensure that your installation proceeds smoothly-please read these

instructions carefully before you begin.

Thank you for selecting American-Standard...the benchmark

of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH

CLEAR WATER. DRY WITH A SOFT COTTON

FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH

SOAPS, ACID, POLISH, ABRASIVES, HARSH

CLEANERS, OR A CLOTH WITH A COARSE

SURFACE.

CARE INSTRUCTIONS:

INSTALL DIVERTER

When ﬁnished tiling the wall, remove PLASTER GUARD (1).

Remove two screws that secure the DIVERTER LID (2) and

remove Lid. Inspect the inside surface of diverter port.

Diverter port must be free of any dirt. Clean if necessary.

Install DIVERTER (3) with SCREWS (4) removed with

DIVERTER LID (2).

Operate DIVERTER (3). DIVERTER (3) should slide in

and out smoothly.

DIVERTER

PORT

INSTALL VALVE TRIM

Figure 1. Push CAP (1) over VALVE CARTRIDGE (2) until

seated against stop. Push CAP (3) over DIVERTER (4) until

seated against stop.

Figure 2. Push ESCUTCHEON HOLDER (5) onto CAP (1)

and attach to valve body with SCREWS (6). Mount

ESCUTCHEON SUPPORT (7) to ESCUTCHEON HOLDER (5)

with SCREWS (8).

Figure 3. Install ESCUTCHEON (9) onto CAP (1) and push

ﬂush against ﬁnished wall. Escutcheon (9) will snap ﬁt onto

ESCUTCHEON SUPPORT (7).

Figure 1.

Figure 2.

Figure 3.

M968836 Rev.1.4

Unthread LEVER HANDLE, loosen SET SCREW and pull

HANDLE off valve stem.

To remove Escutcheon assembly reverse steps in Step 3.

TO GAIN ACCESS TO VALVE FOR SERVICING

Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2).

Remove three SCREWS (3) from FIXATION RING (4) and pull

out PRESSURE BALANCING (5) unit.

Clean SEALS (9) on base of CARTRIDGE (1). Check base of

PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove

CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside

sealing surfaces of VALVE BODY (8).

Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1).

Tighten all screws.

Turn on water supply and see above for installing TRIM and HANDLE.

VALVE LEAKS WHEN SHUT OFF

BACK TO BACK INSTALLATION

ROTATE 180˚

BACK TO BACK INSTALLATION

Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up

and the large outlet port faces down.

Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting.

Top ﬂange should butt up against top of casting.

Reassemble FIXATION RING (4) and CARTRIDGE (1).

Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7)

and clean valve thoroughly.

Examine balancing unit and check condition of O-ring on end of

piston. Piston should move back and forth. Order Repair

Part M952100-0070A if balancing unit is defective.

Replace CAPS (7) and install PRESSURE BALANCE UNIT (5).

Make sure inlets line up with two holes in bottom of casting.

Top ﬂange should butt-up against top of casting.

UNABLE TO MAINTAIN CONSTANT TEMPERATURE

INLETS

LARGE OUTLET

PIPE

PLUG

INSTALL HANDLE, DIVERTER KNOB, TUB

SPOUT AND SHOWER

Remove pipe cap and plug from shower and tub

rough piping.

Install SPOUT ESCUTCHEON (9) onto TUB SPOUT (10).

Apply sealant or Teﬂon tape to threads of tub ﬁller

nipple. Thread TUB SPOUT (10) onto tub nipple.

Install SHOWER ESCUTCHEON (11) onto SHOWER

ARM (12). Apply sealant or Teﬂon tape to threads on

both ends of SHOWER ARM (12) and thread longer

leg of SHOWER ARM (12) into shower elbow.

Thread SHOWER HEAD (13) onto SHOWER ARM (12).

ADJUST HOT LIMIT STOP

By restricting HANDLE rotation and limiting the amount of hot

water allowed to mix with the cold, the HOT LIMIT SAFETY

STOP (1) reduces risk of accidental scalding. To set the maximum

hot water temperature of your faucet, all you need to do

is adjust the setting on the HOT LIMIT SAFETY STOP (1).

Turn CARTRIDGE STEM (2) to the OFF position (coldest setting)

before making adjustment to HOT LIMIT STOP (1). Use a ﬂat

blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1).

Pull forward and rotate counterclockwise one number to limit hot

water temperature. Use ARROW (3) on CARTRIDGE (4)

and NUMBERS (5) on HOT LIMIT STOP (1) for

indication.

COLDER

(Larger Numbers)

0 1 3 5 7 9 11 13 15

HOTTER

(Smaller Numbers)

0 1 3 5 7 9 11 13 15

CAUTION: Protect ﬁnish on SHOWER HEAD and

ARM when installing.

SHR.

ELBOW

TUB

NIPPLE

M968836 Rev.1.4

Thread DIVERTER KNOB (1) onto diverter stem.

PIPE

CAP

Hold ADAPTER (2) onto VALVE STEM (3) and install

ADAPTER SCREW (4) through ADAPTER (2) into

VALVE STEM (3).Tighten ADAPTER SCREW (4) to

secure ADAPTER (2) to VALVE STEM (3).

Install HANDLE BASE (5) onto ADAPTER (2). Insert

SET SCREW (6) into HANDLE BASE (5). Align

HANDLE BASE (4) and tighten with HEX WRENCH

(7) supplied.

A953929-0070A

DIVERTER KIT

M962209-YYY0A

SPOUT KIT

M962495-YYY0A

TUB SPOUT ESCUTCHEON

T064.60X

MODEL NUMBER

A950842-YYY0A

ESCUTCHEON

WITH DIVERTER

SERIN

™

M909917-YYY0A

DIVERTER KNOB

M907053-YYY0A

CAP

M907103-YYY0A

DIVERTER COVER

M968836 Rev.1.4

BATH/SHOWER TRIM KIT

WITH DIVERTER

922388-YYY0A

STREAM STRAIGHTENER

M962818-YYY0A

DEEP ROUGH KIT

(NOT SHOWN)

A918477-0070A

HANDLE SCREW

M918039-0070A

HANDLE ADAPTER

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

IN MEXICO 01-800-839-12-00

CHROME

SATIN NICKEL

002

295

Replace the "YYY" with

appropriate ﬁnish code

M953540-YYY0A

SHOWER HEAD

M962493-YYY0A

SHOWER ARM & FLANGE

M962641-0070A

ESCUTCHEON HOLDER

A912632-0070A

O-RING

M962426-YYY0A

HANDLE KIT

American Standard T064.60X User manual

Brand: American Standard

Model: T064.60X

Category: Sanitary ware

Type: User manual

Download PDF

report

American Standard T064.60X User manual

American Standard T064.60X User manual

Related papers

Other documents