- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
RECOMMENDED TOOLS
M965904 (4/18)
ROUGHING-IN DIMENSIONS
TOWN SQUARE
®
S
PRESSURE BALANCING
BATH AND SHOWER
TRIM KIT
INSTALLATION
INSTRUCTIONS
T45550X
Plumbers’ Putty
or Caulking
Adjustable Wrench Channel Locks
Phillips Screwdriver
Certied to comply with ANSI A112.18.1M
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
Teon Tape Flat Blade Screwdriver
1-5/8" TO 3-1/4"
(41 mm TO 83 mm)
BOTTOM OF
TUB
1/2" NPT
FINISHED WALL
1/2" COPPER
TOP OF
TUB RIM
7-3/8"
(188 mm)
1-3/4" MIN.
(44 mm)
1/2" NPT
7-1/8"
(181 mm)
9-1/8"
(232 mm)
3-1/2"
(90 mm)
6-3/4"
(72 mm)
2-1/2"
(64 mm)
2-5/8"
(66 mm)
7-3/8"
(187 mm)
4" (102 mm)
74" FOR HEAD
CLEARANCE
(188 cm)
18" OPTIONAL
(457 mm)
2-7/8"
(72 mm)
- 2 -
H
C
OFF
1
2
Figure 1.
Figure 3.
2
PLASTER
GUARD
3
4
7
Figure 2.
6
2
5
5
8
UP
UP
UP
1
1
M965904 (4/18)
• Figure 1. Remove plaster guard from valve. Push CAP (1)
over VALVE CARTRIDGE (2) until seated against stop.
• Figure 2. Make sure O-RING (6) is secure within
ESCUTCHEON HOLDER (3). Push ESCUTCHEON
HOLDER (3) onto CAP (1) and attach with
LONG SCREWS (4).
• Figure 3. Install ESCUTCHEON (5) onto CAP (1) and
push ush against nished wall. Escutcheon (5)
will snap t onto ESCUTCHEON HOLDER (3).
INSTALL VALVE TRIM
2
INSTALL, TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE AND HANDLE
• Remove pipe cap and plug from shower and
tub rough piping.
• Install TUB SPOUT (1) onto tub nipple.
CAUTION: Protect finish on TUB SPOUT
when installing.
• Install SHOWER ESCUTCHEON (2) onto
SHOWER ARM (3). Apply sealant or Teon tape
to threads on both ends of SHOWER ARM (3)
and thread longer leg of SHOWER ARM (3) into
shower elbow.
• Thread SHOWER HEAD (4) onto SHOWER ARM (3).
CAUTION: Protect finish on SHOWER HEAD and
ARM when installing.
• Hold ADAPTER (9) onto CARTRIDGE STEM (6) and install
ADAPTER SCREW (10) through ADAPTER (9) into
CARTRIDGE STEM (6).Tighten ADAPTER SCREW (10) to
secure ADAPTER (9) to CARTRIDGE STEM (6).
• Install HANDLE (5) onto ADAPTER (9). Tighten
SET SCREW (7) with HEX WRENCH (8) supplied.
CAUTION
Protect finish on SHOWER HEAD
and TUB SPOUT when installing.
PIPE
PLUG
SHR.
ELBOW
3
2
4
10
HEX
WRENCH
PIPE
CAP
7
8
5
HEX WRENCH
1-3/4" MIN.
TUB FILLER
NIPPLE
6
1
9
OFF
HOT
COLD
- 3 -
M965904 (4/18)
TOWN SQUARE
®
S
PRESSURE BALANCE
BATH AND SHOWER
TRIM KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
8888109-YYY
DIVERTER SPOUT (SLIP-ON)
M907053-YYY0A
ESCUTCHEON CAP
M970465-0070A
ESCUTCHEON HOLDER
M970467-YYY0A
HANDLE KIT
M970221-0070A
SET SCREW
M907891-YYY0A
ESCUTCHEON
078016-0020A
ESCUTCHEON SCREW
A919542-YYY0A
SHOWER ARM
M907633-YYY0A
SHOWER ARM FLANGE
1660515-YYY
SHOWER HEAD (1.8 GPM)
1660516-YYY
SHOWER HEAD (2.5 GPM)
A918477-0070A
HANDLE SCREW
M918039-0070A
HANDLE ADAPTER
COLD
HOT
OFF
MODEL NUMBER
T45550X
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
BRUSHED NICKEL 295
LEGACY BRONZE 278
POLISH NICKEL 013
/
