Ergotron SV31-31001 User guide

Brand: Ergotron

Model: SV31-31001

Category: Multimedia carts & stands

Type: User guide

This manual is also suitable for

SV31-31051

1/14

888-24-052-G-01 rev. J • 12/09

14mm (9/16") 10mm (3/8")

M4 x 10mm

M4 x 8mm

M4 x 5mm

16x

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Nederlands

Benutzerhandbuch - Deutsch

Guida per l’utente - Italiano

Användarhandbok - svenska

http://4support.ergotron.com

For the latest User Installation Guide and StyleLink Software Download please visit:

Encontrará la versión más reciente del manual de instalación del usuario y el software de StyleLink en:

Si vous souhaitez télécharger le dernier manuel d’installation de l’utilisateur ou le logiciel StyleLink, rendez-vous sur :

Den neuesten Installationsleitfaden für Benutzer sowie den neuesten StyleLink-Softwaredownload  nden Sie unter:

Voor de nieuwste Installatiehandleiding voor de gebruiker en voor het downloaden van StyleLink-software gaat u naar:

Per scaricare le versioni più recenti del manuale di installazione e del software StyleLink, andare al sito:

De senaste versionerna av installationshandledningen och nedladdning av programvaran för StyleLink  nns på:

User Guide

Features & Speci cations ............................................... 2 - 3

Set-up .............................................................................. 4 - 6

Cable and Cord Routing ................................................. 7 - 8

Ready On ..........................................................................7

Keyboard Light .................................................................7

Adjustment .................................................................... 9 -10

Auto-Lock Drawer ...............................................................11

Ergonomics .........................................................................12

Maintenance & Safety ........................................................13

Cart Storage ........................................................................14

Warranty ..............................................................................14

StyleView® SV31 LCD Cart

· SV31-31001 without Auto-Lock Drawer

· SV31-31051 with Auto-Lock Drawer

Auto Lock Drawer

(SV31-31051 Cart only)

2/14

888-24-052-G-01 rev. J • 12/09

10.

11.

12.

13.

13a

411

Features & Speci cations

For more information on this or other Ergotron

products, visit our website: www.ergotron.com

-20 °C

- 4 °F

50 °C

122 °F

Relative

Humidity

Range

0-95% rH

-20 °C

- 4 °F

29 °C

86 °F

Relative

Humidity

Range

0-95% rH

Operational Storage

FCC Compliance Statement

The cart has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Changes or modi cations not expressly approved by Ergotron, Inc. could void the user’s authority to operate

the equipment.

Please contact Ergotron for complete EMC compatibility information.

Worksurface

Secure Storage for Notebook, Thin Client or CPU up to 3.75" (95 mm) thick

Front Handle

Height Adjustment Brake

Ready On button wakes computer when set to hibernate mode

USB Hub connects keyboard and mouse USB cables

Keyboard tray slides out, tilts and allows for right or left mousing with attached mouse pouch

Keyboard Light under Front Handle

Cable Management and Storage for excess cables and power supplies

Storage Basket and Rear Handle

Front Locking Casters

Auto-Lock Drawer (SV31-31051 Cart only)

13a. Auto-Lock Drawer Keypad

Height Adjustable LCD Mount attaches LCDs or tablet PC's with 75x75 or 100x100mm mounting interface

WARNING

IMPACT HAZARD!

MOVING PARTS CAN CRUSH AND CUT.

Minimize Lift Tension BEFORE:

· Removing Mounted Equipment.

· Shipping Cart

· Storing Cart

To Minimize Lift Tension

1. Lower worksurface to lowest position.

2. Turn adjustment nut at top of riser

counterclockwise until it stops

(Adjustment may require 40-60 revolutions).

Failure to heed this warning may result in

serious personal injury or property damage!

For More information and instructions refer to product

guide at http://4support.ergotron.com or contact

Ergotron Customer Care at 1-800-888-8458.

822-052

14mm (9/16”)

3/14

888-24-052-G-01 rev. J • 12/09

17"

(432 mm)

3.75"

(95 mm) 1.75"

(44 mm)

12.5"

(318 mm)

18.5"

(470 mm)

(127 mm)

25˚

90˚

12˚

+12˚

LCD

<3 lbs

(1.4 kg)

<4 lbs

(1.8 kg)

<39 lbs

(17.7 kg)

3.4"

(86 mm)

14.6"

(370 mm)

11.8"

(300 mm)

14.4"

(367 mm)

(76 mm)

11.6"

(295 mm)

2.3"

(58 mm)

3.1"

(79 mm)

13.3"

(337 mm)

20.9"

(533 mm)

16.4"

(416 mm)

28.1"

(714 mm)

20.5"

(521 mm)

22.4"

(568 mm)

8.1"

(206 mm)

34.5"

(876 mm)

2.9"

(73 mm)

41.4"

(1053 mm)

47.2"

(1199 mm)

17"

(432 mm)

1.8"

(46 mm)

7.1"

(181 mm)

(102 mm)

1.7"

(43 mm)

16.8"

(427 mm)

4.4" - 9.4"

(112-239 mm)

23.5” - 41.0”

(597-1041 mm)

4.4"

(112 mm)

47.4”- 65.9” (1204-1674 mm)

30.6”- 49.1”

(777-1247 mm)

24.2”- 42.7”

(615-1085 mm)

5.9"

(149 mm)

Features & Speci cations

When  guring dimensions, include

mounted accessories, protruding cables

and port replicators or docking stations.

CPU Compartment

With Independent

LCD Lift:

6-16 lbs (2.7-7.3 kg)

Without Independent

LCD Lift

20 lbs (9 kg)*

* See "How To Eliminate Independent

LCD Lift" section

<3 lbs (1.4 kg) Worksurface

<13 lbs (5.9 kg) CPU Compartment

CAUTION:

If the combined LCD and CPU weight is greater than 23 lbs (10.4

kg) then the CPU must be mounted to the rear of the cart using

the Universal CPU Holder accessory (ordered separately).

Auto Lock Drawer

Weight Capacity

Auto Lock Drawer

<4 lbs (1.8 kg)

(without insert)

<2 lbs (.9 kg)

(with insert)

SV31-31051 Cart only,

see inset, below

Drawer Insert

Weight = 2 lbs (.9 kg)

4/14

888-24-052-G-01 rev. J • 12/09

90˚ 0˚

M4 x 5mm

1x 0˚

22x

75x75mm / 100x100mm

M4 x 10mm

Set-up

WARNING

Impact Hazard!

Moving Parts can Crush and Cut.

Raise monitor to top of vertical

adustment BEFORE removing.

Failure to heed this warning may result in

serious personal injury or property damage!

5/14

888-24-052-G-01 rev. J • 12/09

hg 2x

Set-up

Fan

Fan Cable

WARNING: Fan must always be running when computer is on. Operating

comuter without fan may lead to overheating, resulting in serious personal

injury, and equipment damage.

Connect the USB and Ethernet

Crossover cables to your Computer

NOTE: these cables are

factory-connected to

the USB Hub and routed

from a compartment

at the rear of the cart

to be connected to the

computer at this time.

USB Type A

connection

on computer

Ethernet

Crossover

connection

computer

Plug Fan Cable into

computer USB

Spacers are required under

notebook and battery to ensure

adequate air  ow and to optimize

screen adjustment.

6/14

888-24-052-G-01 rev. J • 12/09

a b

a bc

a1x

2x 1x

Set-up

Route AC

Power

Cords

Place AC Power

Adaptors in

compartment.

7/14

888-24-052-G-01 rev. J • 12/09

Route Cables and Cords

Keyboard Light NOTE: The Keyboard Light is powered from the USB Hub inside the enclosure. Your equipment must be routed into the USB Hub and

your computer must be on for this light to function.

USB to AutoLock Drawer

(factory connected)

Carts with AutoLock Drawer:

Connect Keyboard and Mouse to USB Hub

Carts with no AutoLock Drawer:

Connect Keyboard and Mouse to USB Hub

USB (Type A)

Auto Lock Drawer (factory connected) Auto Lock Drawer Keypad (factory connected)

Ethernet Crossover

(connected to

Computer by User)

Ethernet Crossover

(connected to

Computer by User)

NOTE: Bar Code Scanner should be connected directly to computer USB port.

DO NOT connect Bar Code Scanner to the USB Hub.

NOTE: Bar Code Scanner should be connected directly to computer USB port.

DO NOT connect Bar Code Scanner to the USB Hub.

Keyboard Light

(factory connected)

Keyboard Light

(factory connected)

AutoLock Drawer

Control to Battery Pack

(connected by User)

USB to Battery Pack

(factory connected)

USB to Battery Pack

(factory connected)

USB (Type B)

(factory connected)

USB (Type B)

(factory connected)

USB (Type A)

(connected to Computer by User)

USB (Type A)

(connected to Computer by User)

Ready On

The Ready On button is located on the side of the enclosure. Pressing this button will wake up your computer from hibernate or power off. Setting your equipment to

hibernate as soon as possible is recommended to save battery charge. Your computer must be hooked up via ethernet connection to the Ready On ethernet port inside the

eclosure.

NOTE: Function of Ready On requires external source of power to computer.

Initial Set-up:

1. Turn Computer on.

2. Adjust Bios, Windows Power Management, and NIC settings to enable Wake on LAN.

3. Connect Ethernet Cross-over cable from computer to Ready On.

4. Depress and hold Ready On button for 15 seconds.

5. Turn Computer off.

6. Press Ready On Button. Computer should turn on. If it does not turn on repeat steps 1 - 6. If computer

still does not turn on, contact Ergotron Customer Care.

8/14

888-24-052-G-01 rev. J • 12/09

Route Cables and Cords

Insert cable tie through holder. Wrap cable tie around power cords.

Pull tie

tightly

around

cords.

Trim excess

cable tie

with sissors.

Replace cover.

Remove cover.

NOTE: Carts

with AutoLock

Drawer do not

have cable

cover.

9/14

888-24-052-G-01 rev. J • 12/09

ii iiii

14mm

81x

Adjustment

Release brake to move riser.

Loosen knob, tilt Display to desired

position then retighten knob.

Follow these instructions to tighten or loosen tension.

Lift – Up and down

Tilt – Forward and Backward

It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this

product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments are di cult and do not stay in the desired position, follow

the instructions to loosen or tighten the tension to create a smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a

di erence.

NOTE: Adjustment may require 40 - 60

revolutions.

10/14

888-24-052-G-01 rev. J • 12/09

iii iv 10mm

1x M4 x 8mm

Follow these instructions to tighten or loosen tension.

Lift – Up and down

Adjustment

To Stop Independent LCD Lift

For heavier Displays or when using a

Tablet PC, you can keep the LCD Lift from

moving out of position, by installing this

screw into one of the three holes on the

back of the riser depending on the desired

height.

With Independent

LCD Lift:

6-16 lbs (2.7-7.3 kg)

Without Independent

LCD Lift

20 lbs (9 kg)

WARNING

IMPACT HAZARD!

MOVING PARTS CAN CRUSH AND CUT.

DO NOT remove Stop Screw

without monitor attached.

Doing so will cause monitor pivot to shoot

up rapidly and may cause personal injury.

To Remove Monitor:

1. Remove stop screw while monitor is

attached.

2. Lift monitor to highest postion

3. Remove monitor.

Failure to heed this warning may result in

serious personal injury or property damage!

For More information and instructions refer to product

guide at http://4support.ergotron.com or contact

Ergotron Customer Care at 1-800-888-8458.

822-055

11/14

888-24-052-G-01 rev. J • 12/09

12 3

Auto-Lock Drawer

NOTE: User should

change Master Code

upon receipt of cart.

Lock Drawer (2 methods):

• Wait 4 seconds for drawer to lock automatically

• Press 1 and 2 on number pad simultaneously

Unlock Drawer (3 methods):

• Enter Master Code, then press 1.

• Enter Personal Code, then press 1.

• Key - turn counter clockwise 1/8 turn

Lost Master Code

Contact Ergotron Customer Care for instructions.

AutoLock Drawer Battery Pack

The AutoLock Drawer Control on Non-powered Carts includes a battery pack holding four provided rechargeable NiMH (Nickle Metal Hydride) batteries. To access battery

compartment (located under autolock controller, attached by a Velcro strip) remove the left cover of the cable management area.

Rechargeable

Nickle Metal

Hydride

Drawer Troubleshooting

• Key pad numbers are dark

-Touch anywhere on number pad to activate back-light, (drawer remains

locked until you enter valid code)

-Check to make sure DC cable is connected (SV32 models) or battery

pack is connected (SV31 models)

• Code is accepted but drawer does not open

-For dual drawer systems, make sure other drawer is fully closed and lock

engaged

-For single drawer systems, make sure drawer is fully closed before

entering code

• Drawer won’t open when Personal Code is entered

-Test system by entering Master Code. If drawer doesn’t unlock, follow

"Lost Master Code" instructions.

Flashing LED: Meaning

1: Drawer is open

1 & 2: Waiting for drawer selection (see Unlock Drawer)

3 & 5: Unit is ready to program master or user codes (see Programming New Codes)

5: Drawer is unlocked

All: New code accepted

Erase All Personal Codes (cannot erase only one

code or Master Code):

1 Enter Master Code, then press 1.

2 Press 3 and 5 simultaneously (while blinking)

3 Press 1 and 2 on number pad at the same time

Programming New Codes (Default Master Code: 12345)

Enter Master Code, then press 1.

Numbers 3 and 5 on the Keypad will start  ashing, indicating the Master Code has been accepted.

Simultaneously press 3 and 5 while they are  ashing.

All the numbers will light (you have 3 seconds to enter a code).

Enter a new code—any sequence of 5 numbers. (The  rst code programmed is the new Master Code.)

When the code is accepted, all of the LEDs will  ash once in acknowledgement (you have 3 seconds to enter the next code).

You can then proceed to program up to 10 personal codes by repeating steps 5 and 6.

When  nished entering new codes, system will exit program mode after 3 seconds with a series of LED  ashes.

12/14

888-24-052-G-01 rev. J • 12/09

Ergonomics

Working

customize - to your size

1 Set top of monitor screen about one inch below eye level - Release brake and lift or lower riser

as needed.

2 Tilt screen for comfortable viewing and to reduce eye and neck strain.

3 Pull keyboard tray forward and position mouse tray and mouse pouch on right or left, as needed.

4 Work with elbows bent at about 90° to minimize muscle strain.

5 If the riser moves up and down with difﬁ culty, or if it drifts out of set position, consult the product

manual for adjustment information.

6 Stay in charge!

Powered carts should be plugged into outlet as often as possible to keep battery charged and

computer running.

Moving

stow - before you go

1 During normal movement, release brake and lower worksurface to

lowest position for optimal stability and unobstructed view.

2 Tuck away open trays and return mouse, scanner and other accessories

to their places.

3 Unlock both front casters.

4 Push cart from rear with elbows bent at about 90° to maximize control

and minimize muscle strain.

5 Don’t run out!

Before moving, make sure cord is unplugged from outlet and hooked to

basket for safe travel. Remember, charge battery fully 100% every day!

Maintenance & Safety

Color Symbol Signal

Word Level of Hazard

Red DANGER Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

Orange WARNING Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

Yellow CAUTION Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

None CAUTION

Used without the safety alert symbol indicates a poten-

tially hazardous situation which, if not avoided, may

result in property damage.

Red,

Orange

Yellow

Electrical Indicates an impending electrical hazard which, if not

avoided, may result in personal injury,  re and/or death.

Hazard Symbols Review

The Meaning of Symbols appearing in this Guide, on the Cart or on the Power System

These symbols alert you to a safety condition that demands your attention. You should be able to recognize and

understand the signiﬁ cance of the following Safety Hazards if you encounter them on the Cart or within Cart

documentation such as this Set-up Guide.

EQUIPMENT & ACCESSORIES DISPOSAL

1. Please dispose of all batteries in accordance with

local law

2. User Interface, Auto-lock Drawer, and Ready On

Module should be recycled through an electronics

recycler.

3. Remaining plastics and metals can be recycled

through a commercial recycler.

13/14

888-24-052-G-01 rev. J • 12/09

Safety Alerts Associated with this Product

The following Warnings/Cautions appear in this reference guide or on the cart:

NOTE: Failure to adhere to these guidelines may result in equipment damage or personal injury.

CAUTION: The lift brake helps stablilize the worksurface and keyboard tray during normal use but it DOES NOT increase load capacity. DO NOT load riser with equipment

totalling more than the maximum weight capacity speciﬁ ed by Ergotron. Ensure optimum lift function by testing and if necessary, re-adjusting tension whenever the weight

mounted to the riser changes (i.e., equipment is removed or added). See "Set Riser Lift Tension" adjustment instructions in step 9 on page 5.

CAUTION: Do not operate StyleView Cart with missing or damaged components! Do not remove, modify or substitute Cart components without consulting Ergotron. If you

encounter problems with Cart installation or operation, contact Ergotron Customer Care.

CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.

WARNING: Stored Energy Hazard: The worksurface lift mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this

reason, DO NOT remove equipment unless the worksurface has been moved to the highest position on the tower! Failure to follow this instruction may result in serious personal

injury and/or equipment damage! When Shipping the cart, set the worksurface lift mechanism to the lowest tension setting.

CAUTION: DO NOT loosen, tighten or remove any other nuts or bolts on the riser or top of tower. Tampering with nuts or bolts may result in an unstable Cart, leading to

equipment damage and/or personal injury.

CAUTION: Release Lift Brake before moving work surface! Moving work surface while Lift Brake is engaged may cause serious damage to Lift Engine.

WARNING: In the event that repair of the StyleView Cart is needed, contact Ergotron Customer Care immediately. Cart repair can only be performed by Ergotron, Inc. or by an

Ergotron authorized agent.

CAUTION: Route cables on Cable Channel (right) side of Cart only. Do not store power brick inside base covers. Storing power brick inside base covers may damage electrical

circuts or may result in damage to both Cart and mounted equipment or injury from electrical shock.

Maintenance & Safety

Recommended Periodic Inspection and Maintenance

Component Action How often By whom

ALD Batteries

(SV31 only) Replace 4 ea AA NiMH batteries1Replace when

keypad #4 ﬂ ashing Any user

Ready On Batteries

(SV31 only) Replace 2 ea AA Lithium batteries1

Replace when light

on Ready On ﬂ ashing

Any user

UI, ALD, Ethernet,

USB cables Inspect for wear, pinching, bad

connectors Monthly Any user

Casters Inspect for wear and debris Monthly Any user

Maximum Load Inspect too ensure that maximum

recommended loads are not

exceeded Daily Any user

1. Please dispose of all batteries in accordance with local law

Cleaning and Maintenance

The following procedures are not guaranteed to control

infection. The hospital infection control administrator or

epidemiologist should be consulted regarding cleaning

procedures and processes.

To avoid risk of electric shock, do not expose electrical

components to water, cleaning solutions or other potentially

corrosive liquids or substances.

Do not immerse Cart or Cart components in liquid or

allow liquids to ﬂ ow into the Cart. Wipe all cleaners off surface

immediately using a damp cloth. Thoroughly dry surface after

cleaning.

Do not use ﬂ ammable cleaners on Cart surfaces due to

close proximity of electrical power and equipment.

All paints and plastic Cart components will withstand cleaning

by most commonly used, diluted, non-abrasive solutions such as

quaternary ammonia compounds, ammonia enzyme cleaners,

bleach or alcohol solutions.

• Pen and permanent and dry erase markers can be removed

with 91% isopropyl alcohol and a soft cloth.

• Iodine stains can be removed with commonly used cleaners

and a soft cloth.

• Never use steel wool or other abrasive materials that will

damage the surface ﬁ nish.

• Do not use strong solvents such as trichloroethylene and

acetone. These solvents will damage the surface ﬁ nish.

It is recommended that any cleaning solution be tested on a

small, inconspicuous area to ensure surface is not harmed.

Adjustment, Service, Replacement - DO NOT attempt to

adjust, service or replace any part of the StyleView Cart unless

directed to do so through Ergotron-approved documentation

(i.e. installation instructions). Only Ergotron, Inc. or an Ergotron-

certiﬁ ed entity may adjust, service or replace StyleView Cart

components. If any component on the Cart is missing or

damaged, the Cart must not be used, contact Ergotron Customer

Care immediately to request a replacement part.

Cables - Keep cables neatly organized on the Cart (a variety of solutions are provided with your cart for this purpose). Excess cables should be routed away from moving

components with cable clips. Review Cable Routing section of this guide, or contact Ergotron Customer Care for more information.

Casters - Check casters periodically to make sure they are clean and free of debris that would prevent smooth travel. Avoid moving Cart across uneven, dirty or damaged surfaces.

Customer Equipment- Make sure equipment is balanced and mounted securely to Cart. Do not reposition Cart components on riser or tower unless instructed to do so in the

installation instructions. Moving Cart components too high or too low on the Riser may create an unstable condition, leading to equipment damage or even personal injury. Contact

Ergotron Customer Care for information about moving Cart components.