Legrand Home Lighting Expansion Module - 364726-01 Installation guide

Legrand
Brand
Legrand
Model
Home Lighting Expansion Module - 364726-01
Type
Installation guide

Legrand Home Lighting Expansion Module - 364726-01

Legrand Home Lighting Expansion Module - 364726-01 is an expansion device to the OnQ Home Lighting Controller. It provides control of up to 93 additional Advanced Lighting Control (ALC) switches and I/O Modules. With this expansion module, the OnQ Home Lighting System can control up to 124 ALC lighting control switches and I/O Modules.

The Lighting Expansion Module mounts to an OnQ enclosure or network center bracket adjacent to the OnQ Home Lighting Controller. It connects to the controller's EXPANSION connector with a flat ribbon cable assembly.

Legrand Home Lighting Expansion Module - 364726-01

Legrand Home Lighting Expansion Module - 364726-01 is an expansion device to the OnQ Home Lighting Controller. It provides control of up to 93 additional Advanced Lighting Control (ALC) switches and I/O Modules. With this expansion module, the OnQ Home Lighting System can control up to 124 ALC lighting control switches and I/O Modules.

The Lighting Expansion Module mounts to an OnQ enclosure or network center bracket adjacent to the OnQ Home Lighting Controller. It connects to the controller's EXPANSION connector with a flat ribbon cable assembly.

OnQ Home Lighting Expansion Module
OnQ Technologies, Inc. www.onqtech.com Installation Instructions
Fulling Mill Road, Middletown, PA 17057 800-321-2343 IS-0274 Rev. A
Figure 1. Home Lighting Expansion Module
INTRODUCTION
As an expansion device to the OnQ Home Lighting Controller, the
part no. 364726-01 Home Lighting Expansion Module provides
control of up to 93 additional Advanced Lighting Control (ALC)
switches and I/O Modules. When expanded, the OnQ Home
Lighting System provides control of up to 124 ALC lighting control
switches and I/O Modules.
INSTALLATION
The Lighting Expansion Module mounts to an OnQ enclosure or
network center bracket adjacent to the OnQ Home Lighting
Controller. Each Lighting Expansion Module is furnished with a flat
ribbon cable assembly to connect the Lighting Expansion Module
to the OnQ Home Lighting Controller’s EXPANSION connector.
When the power source shunt is placed in position B, the Lighting
Expansion Module distributes 12VDC power from the OnQ Home
Lighting Controller. When the power source shunt is placed in
position A, the Lighting Expansion Module distributes 12VDC
power from an external power supply. An external power supply
should be employed for 12VDC loading that exceeds 200mA. Total
external device 12VDC loading should not exceed 600mA.
Figure 2. ALC BRANCH Connector Pin-Out
CONNECTIONS
The Lighting Expansion Module provides three ALC
communication ports. The Lighting Expansion Module provides
three modular jack connectors for interfacing ALC switches and I/O
modules to the communication ports; ALC BRANCH 2, ALC
BRANCH 3 and ALC BRANCH 4.
Positions 4 and 5, of the ALC BRANCH 2 port, provides
connections for ALC addresses 32 thru 62 and up to 500 feet of
category rated cable. Positions 4 and 5, of the ALC BRANCH 3
port, provides connections for ALC addresses 63 thru 93 and up to
500 feet of category rated cable. Positions 4 and 5, of the ALC
BRANCH 3 port, provides connections for ALC addresses 94 thru
124 and up to 500 feet of category rated cable.
Positions 1 and 8, of the ALC BRANCH ports provide connections
for distribution of 12VDC power to part no. 364677-01 ALC Branch
Hubs and part no. 364678-01 I/O Modules. Current draw from all
connected external devices should not exceed 600mA.
OPERATION
Upon powering up the Home Lighting Controller and Lighting
Expansion Module combination, the STATUS LED indicator on the
controller will blink at a rate of approximately 1 blink per second. If
the STATUS indicator remains On or Off, it is an indication of a
fault. In the event of a fault, check all connections and power to the
Home Lighting Controller and Lighting Expansion Module.
Subsequent to making any alterations to the system, such as an
address change to an ALC switch, the Home Lighting Controller
should be reset. Resetting can be accomplished either by
removing power from the Home Lighting Controller or by pressing
the RESET button.
Note: Remove power to the controller prior to connecting new
devices. Verify all connections prior to restoring power
The ALC ACTIVITY LED indicator serves as a diagnostic feature.
The ACL ACTIVITY LED will blink whenever the controller detects
any system activity. The ALC ACTIVITY LED is particularly useful
in verifying proper connection of ALC switches and I/O modules.
When any ALC switch button is pressed or I/O Module input is
activated, the ALC ACTIVITY indicator will blink in response to the
event.
Figure 3. Expanded Home Lighting System
POS 1 POS 8
Position 1: 12VDC
Position 4: ALC Comm -
Position 5: ALC Comm +
Position 8: GND
OnQ
EXPANSION OUT
EXPANSION IN
ALC BRANCH 2 ALC BRANCH 3 ALC BRANCH 4
AUX
12VDC
+
-
.
.
LIGHTING EXPANSION
A B
OnQ
Serial Expansion Module
TRANSMIT
RECEIVE
EXPANSION OUT
EXPANSION IN
SERIAL COMM
232
485
OnQ
EXPANSION OUT
EXPANSION IN
ALC BRANCH 2 ALC BRANCH 3 ALC BRANCH 4
AUX
12VDC
+
-
.
LIGHTING EXPANSION
A B
.
Home Lighting Controller
OnQ
ALC
ACTIVITY
STATUS
RESET
EXPANSION
X10 ADDRESS
ALC COMM
BR1
X10 COMM
12VDC
+-
.
OnQ Home Lighting Expansion Module
OnQ Technologies, Inc. www.onqtech.com Installation Instructions
Fulling Mill Road, Middletown, PA 17057 800-321-2343 IS-0274 Rev. A
WIRING DISTRIBUTION
The part no. 364645-01 Wiring Distribution Module is intended for
use with the Home Lighting Controller and the Lighting Expansion
Module. When connected to the Lighting Expansion Mdoule, the
Distribution Module supports direct wiring of ALC Dimmers, Relay
Switches, Auxiliary (slave) Switches, Scene Switches, Program
Switches, I/O Modules and ALC Branch Hubs. Direct wiring is
conducive to testing and quick isolation of faults when they occur.
A modular patch cable (included) connects the Distribution
Module’s CONTROLLER jack to the Lighting Expansion Module’s
ALC BRANCH jacks. All connection points consist of 110 style IDC
connectors for connection of category 3, 5 or 5E cables.
Figure 4. Lighting Expansion with Wiring Distribution
WARRANTY
OnQ warrants to the end-user, each new ALC product to be free of
defects in materials or workmanship for a period of one year from
the date of original purchase from OnQ or its authorized reseller or
installer. Each product is deemed warrantable under conditions of
normal use and when installed and operated within OnQ
specifications and in accordance with the applicable National
Electrical Code and Safety Standards of Underwriters
Laboratories. When determined to be warrantable, OnQ shall at its
option and expense, replace any defective product with a new or
reconditioned product. OnQ will continue to warrant any replaced
product for a period of ninety (90) days from shipment, or through
the end of the original warranty period, which ever is longer.
OnQ
EXPANSION OUT
EXPANSION IN
ALC BRANCH 2 ALC BRANCH 3 A LC BRANCH 4
AUX
12VDC
+
-
.
.
LIGHTING EXPANSION
A B
+
-
+
-
OnQ
1
2
3
4
5
6
7
ON OFF COM
+
-
+
-
+
-
ALC Distribution Module
ON OFF COM
ON OFF COM
ON OFF COM
ON OFF COM
+
-
+
-
ON
OFF
COM
+
-
ON OFF COM
8
3
GND
4
IN
CONTROLLER
GNDIN IN
IN
12
+
-
GND12V
+
-
+
-
+
-
OnQ
1
2
3
4
5
6
7
ON OFF COM
+
-
+
-
+
-
ALC Distribution Module
ON OFF COM
ON OFF COM
ON OFF COM
ON OFF COM
+
-
+
-
ON
OFF
COM
+
-
ON OFF COM
8
3
GND
4
IN
CONTROLLER
GNDIN IN
IN
12
+
-
GND12V
+
-
+
-
+
-
OnQ
1
2
3
4
5
6
7
ON OFF COM
+
-
+
-
+
-
ALC Distribution Module
ON OFF COM
ON OFF COM
ON OFF COM
ON OFF COM
+
-
+
-
ON
OFF
COM
+
-
ON OFF COM
8
3
GND
4
IN
CONTROLLER
GNDIN IN
IN
12
+
-
GND12V
+
-
  • Page 1 1
  • Page 2 2

Legrand Home Lighting Expansion Module - 364726-01 Installation guide

Legrand
Brand
Legrand
Model
Home Lighting Expansion Module - 364726-01
Type
Installation guide

Legrand Home Lighting Expansion Module - 364726-01

Legrand Home Lighting Expansion Module - 364726-01 is an expansion device to the OnQ Home Lighting Controller. It provides control of up to 93 additional Advanced Lighting Control (ALC) switches and I/O Modules. With this expansion module, the OnQ Home Lighting System can control up to 124 ALC lighting control switches and I/O Modules.

The Lighting Expansion Module mounts to an OnQ enclosure or network center bracket adjacent to the OnQ Home Lighting Controller. It connects to the controller's EXPANSION connector with a flat ribbon cable assembly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents