Bradford White PDX1-50S6FBN User manual

Brand: Bradford White

Model: PDX1-50S6FBN

Type: User manual

1 238‐50320‐00B 9/15



SUPPLEMENT–VENTINGINSTRUCTIONSFORINSTALLATIONANDOPERATIONINSTRUCTIONMANUALSFOR

THEFOLLOWINGPRODUCTTYPES:

HIGHEFFICIENCYCONDENSINGCOMMERCIAL,COMMERCIALPOWERDIRECTVENT,LIGHTDUTYCOMMERCIAL

POWERDIRECTVENT,LIGHTDUTYCOMMERCIALPOWERVENT,RESIDENTIALPOWERDIRECTVENT,

RESIDENTIALPOWERVENTMODELSERIES,ULTRALOWNOxRESIDENTIALPOWERDIRECTVENT,ULTRALOW

NOxLIGHTDUTYPOWERDIRECTVENT,ULTRALOWNOxRESIDENTIALPOWERVENT,ULTRALOWNOxLIGHT

DUTYPOWERVENT,HIGHPERFORMANCESERIESPOWERVENT,COMBIPOWERVENT,SOLARPOWERVENT

GASBACKUP.



INSTALLATIONOFDURAVENTPOLYPRO®SINGLEWALLPOLYPROPYLENEVENTINGSYSTEMS



ThissupplementisfortheinstallationofpolypropylenesinglewallventingsystemmanufacturedbyM&GDuraVent,Inc.

TheDuraVentPolyproventingsystemisaCSAapprovedalternativetothePVC,ABS,andCPVCventingcomponentsfor

theHighEfficiencyCondensing Commercial,

CommercialPowerDirectVent,LightDutyCommercialPowerDirectVent,

LightDutyCommercialPowerVent,ResidentialPowerDirectVent,ResidentialPowerVentModelSeries,UltraLow

NOxResidentialPowerDirectVent,UltraLowNOxLightDutyPowerDirectVent,UltraLowNOxResidentialPower

Vent,UltraLowNOxLightDutyPower

Vent,HighPerformanceSeriesPowervent,CombiPowerVent,SolarPowerVent

GasBackupModelSeries.



TheDuraVentventingsystemcomponentsareULCS636approvedandlistedbyarecognizedagencyandmaybe

installedintheU.S.andCanada. Allcomponentsusedmustbefromthesamemanufacturerand

aredesignedforuse

withtheabovenotedproducts. TheDuraVentcomponentsmaybepurchasedfromplumbingsupplydistributors. The

ventsizediameterandmax imu mventlengthsmustbefollowedasdetailedinthe InstallationandOperatingInstruction

Manualthatwassuppliedwiththewaterheater. Thoroughlyreadandunderstand

theventingsectionoftheinstruction

manualsuppliedwiththewaterheaterbeforeproceedingwiththefollowinginstructionsinthissupplement. Thevent

terminalssuppliedwiththewaterheaterorthefactoryapprovedaccessoryventterminalkitsmustbeusedwiththis

ventingsystem.



WARNING

The venting system must be properly installed. Failure to properly install the vent system could result in

property

damage, personal injury, or death.

DO NOT install damaged venting system components. If damage is evident then please contact the supplier

where

the water heater or venting system components were purchased for replacement parts.

Use only the vent terminals provided or factory authorized terminals for venting this water heater.

The water heater requires its own separate venting system. Do not connect the exhaust vent into an existing vent

pipe

or chimney.

All of the exhaust venting connections must be leak checked with a soap solution upon initial start-up of the

water

heater. Any leaks must be repaired before continuing operation of the water heater.

Do not terminate the venting where noise from the exhaust or intake will be objectionable. This includes

locations

close to or across from windows and doors. Avoid anchoring the vent and intake pipes directly to framed

walls, floors,

or ceilings unless rubber isolation pipe hangers are used. This prevents any vibrations from being

transmitted into the

living spaces.

Do not exceed the venting distances or the number of elbows listed in the instruction manual supplied with the

water

heater. Exceeding the maximum venting distances may cause the water heater to malfunction or cause

an unsafe

condition.

DO NOT operate this water heater until the venting installation is complete and the piping completed. Failure

complete installation before operation can result in property damage, personal injury, or death.

2 238‐50320‐00B 9/15



WARNING

DO NOT install Duravent Polypro venting components with any other manufacturer’s vent components.

Duravent

components must be used exclusively throughout the entire venting system from the water heater

coupling or vent

connection to the outside wall or ceiling near the vent terminal location.

This supplement is intended only for additional information for installing Duravent Polypro single wall venting system

and the instruction manual supplied with the water heater must be followed for the detailed information provided for

the

venting system installation.



Step1: ThoroughlyreadandunderstandtheventingsectionoftheInstallationandOperatingInstructionManualthat

wassuppliedwiththewaterheaterbeforedeterminin gthelocationofthewaterheaterandtheventterminals.Locate

thewaterheaterfortheshortestpracticalventlengthtotheoutside. Measurethetotalventingdistancerequiredto

reachtheoutsidewallorroof. Determinethediameteroftheventingcomponents

touseforthelengthofventpipe

(andcombustionairsupplyfordirectventmodels)requiredbyreferringtotheventingtablesintheinstructionmanual

forthemaximumventlengthforeachdiameterpipesize. Obtainallthenecessaryventingsystemcomponentsforthe

installation.



Step2:Before

installation,inspecteachventcomponentfordamagemakingsurethegasketsforeachcomponentare

fullyintactandinundamagedcondition. Donotattempttoinstallorrepairdamagedcomponents.Ifagasketis

damaged,theseareavailablefromthesupplierofDuraVentcomponents. Donotusegasketsfromanother

manufactureranddonottrytorepairthegasket.



Step3:ADuraVentPVCto

Polypropyleneadapter(referredbyDuraVentasApplianceAdapters,2PPS‐AD,3PPS ‐AD,or 

4PPS‐AD)mustbeusedtoconnectintoaPVCcouplingortee(CommercialandResidentialPowerDirectVentairintake

connections),condensateelbow(HighEfficiencyCommercialCondensingmodels)ortheexhaustoutletadapterfor

CommercialPowerVentandResidentialPowerVentmodels.Tomaketheinsertionofthegasketedfittings

intothe

couplingeasier,rotatethejointsslightlyandusewatertolubricatethegaskets. DONOTuseanyotherkindoflubricant.



Wetthegasketsurfaceandinsideofthecouplingusingyourfingerorwetpapertowelandinsertthemaleendofthe

adapterwiththeexterior

gasketintothecoupling,condensateelboworexhau stoutletadapterconnection. Ifalarger

ventdiametersizeistobeused,usetheappropriatelysizedreducercouplingfirstonthewaterheaterintakeorexhaust

ventconnectionasdetailedintheinstallationmanualsuppliedwiththewaterheat er. Seethe

followingphotos.



HighEfficiencyCondensingCommercialModels:Usetheappropriateprimerandcement(refertoventingsectionof

instructionmanualwithwaterheater)forcementingaPVCcoupling(notsuppliedwithwaterheater)totheendofthe

PVCairintakepipeconnection.Usingyourfinger,wetwithwaterthemalegasketedendoftheDuraVentPVCto

PolyProadapterandfullyinsertintotheairintakecoupling. Loosen

theDuraVentadapterconnectorclamp(PPS‐PAC)

andinstalloverthePVCcoupling. Seefollowingphotos.

WARNING

Use only water for lubricating the gaskets and pipe ends to allow easy insertion. DO NOT use any other kind of

lubricant, since deterioration of the gasket may result, which may allow dangerous flue gases to leak into the room.

If the vent pipe needs to be disassembled after the gasket has dried, wet the joint thoroughly to loosen the

connection.

3 238‐50320‐00B 9/15



InstallPVCpipecouplingoverairintakepipeconnection

andcementtopipeusingappropriatesolventandcement. WetgasketsofDuraVentPVCAdapterusingfinger.



InsertmalegasketedendofDuraVent

PVCadapterintoPVCpipecoupling. InstallDuraVentAdapterConnector Clamp(PPS‐PAC)overthe

PVCcoupling sothatclampbracketssecuretheshoulderofPVC

adapterfitting. Tightenclampscrewssecurely.



PVCPipeCoupling(not

suppliedwithwaterheater)

WaterHeaterPVCAirIntake

Pipe.Useappropriate

solventandcementto

cementcouplingtopipe.

Wetgasket usingwater

withfinger

MaleGasketedendofPVC

adapter



FlueClampbandfitoverPVCAdapter

shoulderandPVCCoupling.Tighten

clampscrewssecurelywithscrewdriver.

WARNING

DuraVent Adapter Connector Clamps (p/n: PPS-PAC) MUST be properly

installed to secure the PVC Vent Adapter. DO NOT operate the vent system

without first installing the Flue Adapter Connector Clamps.

4 238‐50320‐00B 9/15



ForHighEfficiencyCommercialModelseriesexhaustconnection,wetoutsidegasketwithfingerandinsertPVCadapter

intothecondensateelbow. InsertDuraVentPVCAdapterfittingintoCondensateElbowasshown.



InstallDuraVentConnectorClamparoundoutsideof TightenConnectorClampScrewtosecurePVCAdapterand

CondensateElbowasshown. AdapterandVentPipeintocondensateElbow.



PVCAdapter‐

intoElbow

WetgasketwithwaterusingfingerofPVCAdapter

CondensateElbow

ConnectorClamp

aroundPPpipe

InstallConnectorClampoverCondensateElbow

TightenConnectorClamp

5 238‐50320‐00B 9/15



CommercialandResidentialPowerDirectVent/PowerVentModels:

Forinstallationofcommercialandresidentialpower

ventmodels,installthemaleendofthePVCto

PolypProadapterintotheairintakepipeteeasshown.

InstalltheadapterconnectorclampoverthePVCadapter.

TheninstalltheelboworventpipesectionintothePVC

adapter. Tightentheclamp

bandsoftheadapterconnector

totheairintaketeeandpipeelboworstraightpipesectionto

secureventpipetothewaterheaterairintaketeeasshown

below.



PVCAdapter

Fitting

AirIntakePipeTee

AdapterConnectorClamp–FitsoverAirIntake

Teeandnextventpipesectionasshown.

6 238‐50320‐00B 9/15



Fortheexhaustventingforallpowerventandpowerdirect ForCommercialPowerDirectVentmodels,insert

ventmodels,insertthePVCAdapterintotheExhaustOutlet PVCAdapterintoExhaustOutletAdapter.

Adapter. Onresidentialmodels,tightentheclamptosecure

thePVCAdapter.



InstalltheAdapterConnectorClampoverthePVCadapterandinstalltheelbowornextsectionofstraightpipeinto

thePVCadapter. ThentightentheclampbandsoftheAdapterConnectoraroundtheExhaustOutletAdapterand

Elbowtosecureventingsystem.

ExhaustOutletAdapterwith

clampforresidentialpower

ventedmodels. Tightenclamp.

Tightenclampscrewstosecure

ventpipeelbowtoexhaust

outletadapter.

ExhaustOutletAdapterfor

PowerDirectVentCommercials.

7 238‐50320‐00B 9/15



Step4:Usingafingerorpapertowel,wetwithwatertheinsidegasketofthePVCadapterandthemaleend(without

gasket)oftheelboworstraightsectionofpipeforrunningtheexhaustorintakepipefromthewaterheater.



SteeljointLockingBands(availablefromDuraVentsupplier)mustbeusedateachpipejoint. Theconnectorringsensure

thatthejointsdonotseparateunderheavyloads. Theseconnector

ringsmustbeusedtocomplywithULC‐S636

requirements.Seefollowingphotowiththejointconnectorattachedtothepipesections.

InsertaLockingBandoverthemaleendoftheventpip esectionwiththehookandlegfacingthejoint. Insertthemale

endoftheelbowor

straightsectionintothePVCadapter. Useatwistingmotionwhilepushingthemaleend ofthepipe

orelbowintothePVCadaptertofullyseatintothegasket. Themaleendofthepipeorelbowmustalwayspointtoward

thewaterheater.



SecureLockingBandtoconnectionjointbyslidingthehookoverthelipofthejointasshownbelow.



Useatwistingmotiontoinsertmaleendof

ventpipesectionintoPVCAdapter

LockingBand first inserted over end of

vent pipe section

PushhookofLockingBandoverthelipof

thejointtosecuretheventpipe

PVCAdapter

WARNING

DO NOT operate vent system without

properly installing Locking Bands.

8 238‐50320‐00B 9/15



Step5:DuraVentsuppliedsupportbracketsmustbeusedtosupportthepipesections. Theventpipesectionsmustbe

supportedaminimumofevery10feet(3meters)ofverticalrunoroneveryhorizontalpipesection. Consultlocalcodes

foradditionalrequirements.

DuraVentsuppliestwotypesofapprovedclampsavailableforhangingtheventpipe.ThePolypropylenesnapstyle

clampcanbeattachedateitherthemaleorfemale

endofthepipe.Determinethelocationfortheanchorbolt

mountingtothewallorframingmember. Mounttheanchorboltsuppliedwiththeclamp.Aligntheencapsulatednut

oftheclampwiththeanchorboltandrotatethebodyofclampwiththenutontothethreadsof

theanchorbolt. With

theventpipeinplace,theclampisthensnappedtogetherbyclosingtheclamparoundtheventpipebodyorfemale

endofthepipe.



ThemetalWallStraptypeclampcanonlybemountedonthebodyoftheventpipe.Openthemetal

clamptofitaround

thebodyoftheventpipeandslideintothedesiredlocationtosecuretothewallorceiling. Securetothewallor

structuralmemberbyusing(2)1½”#8woodscrewsorequivalent(notsuppliedwithclamp). Securetheclamparound

theventpipe

bytighteningthenutsandboltsoftheclamp.





WARNING

Make sure pipe sections are fully inserted into the PVC adapter and/or gasketed end of DuraVent fitting. Insertion

depth is no less than 2 inches.

Plasticclamplatchedaround

bodyofventpipe

LagBoltscrewsintowall

studandclampscrews

ontobolt. Clampthen

fastensaroundventpipe.

9 238‐50320‐00B 9/15



PlasticClampalsofitsoverFemaleFlan geofDuraVentVentPipeSections



PlasticClampopeningallowsroomforLockingBandstohookoverflaredfemalejoint



Position clamp to fit betweenraised

“bump” on female flange asshown

10 238‐50320‐00B 9/15



TightenMetalClamparoundbodyofventpipe. Metalclampfastenstowallwithwoodscrews







HighEfficiencyCommercial CondensingModels:

Forhorizontalsectionsoffluepipe,thepipemustbeinstal ledwithaslightupwardslopeofapproximately¼inchper

foot(20mmpermeter)towardthewaterheatertoallowcondensatetodrainintothecondensateelbow.

ResidentialandCommercialPowerDirectVent/PowerVentModels:

Topreventcondensatefromaccumulatingintheexhaustblower,installthehorizontalventpipewithadownwardslope

towardtheventterminalof¼inchperfoot(20mmpermeter)ofhorizontalventpipe.Anoptionalcondensatekitis

availableforresidentialpowerventmodelsorateefittingwithacondensatedrainloopmaybeusedoncommercial

powerdirectventmodelstopreventcondensateaccumulationin

theblowerforlongverticalrunsofventpipe.Referto

theventingsectionoftheInstallationandOperatingInstructionssuppliedwiththewaterheater.



Step6:Ifanyofthestraightpipesectionsneedtobecut,useahacksawandmakeastraightcutonthemale

(ungasketed)endofthepipe.Whenmakingthecut,allowforthe2”minimum(51mm)insertiondistanceinsidethe

femaleendofthepipe.Makesurethecutsaremadesquareandusearazorknifetodeburrtheedgesofthecutpipeto

avoidanysharpedgesthat

maydamagethegasket.

DuraVenthasadjustableventpipesectionsavailable,whichallow4.5inches(114mm)ofadjustmenttothelength.



WARNING

Cut pipe edges must be properly deburred. Damage to the gasket from not deburring the edges of the cut male

end may result in the release of dangerous flue products.

11 238‐50320‐00B 9/15



Cutendofpipetolengthusingahacksaw.Cutmale Deburringcutpipeedgewithrazorknifetoremove

endonlyandallowfor2”insertiondepthintofemaleendof sharpedgestopreventgasketdamage.

fitting.



Step7:Continueinstallingstraightsectionsofpipeandelbowsandsupportwithpipesupportclampsaspreviously

shownoneveryhorizontalpipesectionoratleastevery10feet(3meters)forverticalruns. Runtheventpipenearthe

outsidewallorrooftobeterminated.ADuraVentPVCtoPolyProAdapter(2”,3”or4”diameters)mustbeusedto

connecttheDuraVentpolypropyleneventpipe

toPVCpipefirstbeforeexitingthewallorroof.Thefemaleflaredend

(insidegasket)ofthelastDuraVentpipesectionmustbecutoffattheproperlengthneeded.Connectthefemaleendof 

thePVCAdpaterintotheendofthelastpipe. ConnectthePVCcoupling

overthemalegasketedendofthePVC

TerminationAdapter.SecurethePVCpipecouplingtotheDuraVentPVCadapterwiththeAdapterConnectorClampand

detailedpreviously. CutthePVCpipetothelengthneededtoexitthewallorroof. Refertotheinstallationinstruction

manualsuppliedwiththe

waterheaterforinformationregardingthelocationoftheventterminals.



Cutthemaleendofthelastpieceofpipetothelengthasneededtogetneartheexitingwallorceiling

ofthedesiredoutsideventterminallocation. Installthislastsectionofpipe.

Deburrcutpipewithrazorknifetoremove

sharpedges.

12 238‐50320‐00B 9/15



InstalltheappropriatediameterDuraVentPVCAdapterontheendofthelastpipe.



InstallaPVCcouplingontothemalegasketedendoftheDuraVentPVCAdapter. Areducercouplingmaybeneededto

usethesuppliedventterminalsif alargerpipediametersizewasused.CementthestraightsectionofPVCpipetothe

PVCpipecoupling.InstallthePVCpipeto

exitthewallorroof,andthencementtheventterminalontothePVCorCPVC

pipe.RefertotheventingsectionofthewaterheaterInstallationandOperatingInstructionmanualfortheappropriate

solventandcementtouse. TheexhaustventterminalfortheEFmodelseriesisshown.

Usetheventterminalssupplied

withthewaterheater. Seethefollowingphotos.



InstallPVCPipeCoupling(notsupplied)overthemaleendofDuraVentPVCAdapter.



Cutendofventpipe

DuraVentPVCtoPolyProadapterattaches

tocutmaleendoflastpipesection.

PVCCouplingattachesto

DuraVentAdapter.

13 238‐50320‐00B 9/15



SecurethePVCcouplingtothePVCTerminalAdapterwiththeDuraVentFluePipeClamp. Cementashortsectionof

PVCpipeintothePVCpipecoupling.CementthesuppliedPVCexhaustterminalcouplingontothePVCpipe.



Step8:Aftertheventingsystem installationiscompleted,startthewaterheaterandcheckalljointsforleaksusinga

soapywatersolution.Anyleaksfoundmustberepaired. Ifagasketisdamaged,replacementgasketsmaybeobtained

fromthelocalDuraVentsupplier.



SecurePVCPipeCouplingtoPVC

AdapterwithAdapterConnector

Clamp.

SuppliedAirIntakeTerminal

CementPVCPipeCouplingandVent Terminal to

PVCpipeusingapprovedsolventand cement.

WARNING

All of the exhaust venting connections must be leak checked with a soap solution upon initial start-up of the water

heater. Any leaks must be repaired before continuing operation of the water heater.

Periodically check all venting system connections for leakage. Replace any defective venting components. Refer

to the maintenance section of the Installation and Operating Instructions for further details.

Bradford White PDX1-50S6FBN User manual

Bradford White PDX1-50S6FBN User manual

Bradford White PDX1-50S6FBN User manual

Related papers

Other documents