114233-2-AA (9626)
Copyright 1997 Kohler Co.
DRAIN SHROUD AND P-TRAPS
BEFORE YOU BEGIN
HOW TO USE THESE INSTRUCTIONS
NOTES
Drain shroud conceals drain for console tables.
Shut off the main water supply.
Observe all local plumbing codes.
REQUIRED TOOLS AND MATERIALS
Adjustable or open end wrench
Strap wrench
DRAIN SHROUD INSTALLATION
Install pop-up drain per manufactures instructions.
Slide drain shroud with slot facing toward the back, up
over tailpiece and around ball lever rod, until contact with
locknut on pop-up drain.
At this point, p-trap must be installed to hold drain shroud
in position.
Tailpiece
Drain Shroud
Slot
Ball Lever Rod
P-TRAP INSTALLATIONS
K-9018 with 1-1/4” O.D. inlet, and 1-1/4” O.D. outlet.
Intended for console table installations.
Insert tube into drain outlet and connect with nut and
gasket (not supplied). Slide flange back to wall, to cover
the drain outlet.
Place trap nut and gasket onto tailpiece. Slide trap over
tailpiece and tube elbow. Tailpiece must extend 1” to 2”
into trap. Tailpiece may have to be cut to fit. Tighten nuts
and gaskets.
Cleanout plug is used to remove any debris which has
fallen into the trap.
Tailpiece
Trap
Nut
Gasket
Nut
Gasket
Flange
Tube
Drain
Outlet
Cleanout Plug
Tube
Elbow
2
114233-2-AA (9626)
Kohler Co., Kohler, WI
K-9020 with 1-1/4” O.D. inlet, and 1-1/4” N.P.T. outlet.
Thread end of tube into drain outlet. Slide flange back to
wall, to cover the drain outlet. Insert other end of tube into
elbow and connect with nut and gasket.
Place trap nut and gasket onto tailpiece. Slide trap over
tailpiece and into elbow. Tailpiece must extend 1” to 2” into
trap. Tailpiece may have to be cut to fit. Tighten nuts and
gasket.
Cleanout plug is used to remove any debris which has
fallen into the trap.
Tailpiece
Trap
Nut
Gasket Nut
Gasket
Flange
Tube
Drain
Outlet
Cleanout Plug
Elbow
Nut
K-9021 with 1-1/4” O.D. inlet, and 1-1/2” N.P.T. outlet.
Thread end of tube into drain outlet. Slide flange back to
wall, to cover the drain outlet. Insert other end of tube into
elbow and connect with nut and gasket.
Place trap nut and gasket onto tailpiece. Slide trap over
tailpiece and into elbow. Tailpiece must extend 1” to 2” into
trap. Tailpiece may have to be cut to fit. Tighten nuts and
gasket.
Cleanout plug is used to remove any debris which has
fallen into the trap.
Tailpiece
Trap
Nut
Gasket Nut
Gasket
Flange
Tube
Drain
Outlet
Cleanout Plug
Elbow
K-9022 with 1-1/2” O.D. inlet, and 1-1/2” N.P.T. outlet.
Thread end of tube into drain outlet. Slide flange back to
wall, to cover the drain outlet. Insert other end of tube into
elbow and connect with nut and gasket.
Place trap nut and gasket onto tailpiece. Slide trap over
tailpiece and into elbow. Tailpiece must extend 1” to 2” into
trap. Tailpiece may have to be cut to fit. Tighten nuts and
gasket.
Cleanout plug is used to remove any debris which has
fallen into the trap.
Tailpiece
Trap
Nut
Gasket Nut
Gasket
Flange
Tube
Drain
Outlet
Cleanout Plug
Elbow
INSTALLATION CHECKOUT
Turn water supplies on and run water through drain to
check for leaks at all P-trap connections.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kohler K-9000-CP Installation guide
-
-
-
-
Clear Flo K-7160-TF-SN Installation guide
-
-
-
-
Kohler K-7437-K-CP Installation guide
-
Other documents
-
Oasis 504339 Installation guide
-
Bradley SN2013/AST4 Installation Instructions Manual
-
Halsey Taylor RC Owner's manual
-
-
American Standard CADET 8115F Installation Instructions Manual
-
-
-
-
-