Kohler K-7167-CP Installation guide

Type
Installation guide

This manual is also suitable for

Kohler K-7167-CP is a 2" brass adjustable pop-up drain designed for use with 24" to 26" baths. It features a removable strainer for easy cleaning and a reversible drain "T" for vertical or horizontal drainage. The overflow ell has lubricated O-rings for a secure fit, and the hold-down plate is secured with screws for added stability. The drain stopper has a 3/8" rise above the strainer and can be adjusted for clearance if needed.

Kohler K-7167-CP is a 2" brass adjustable pop-up drain designed for use with 24" to 26" baths. It features a removable strainer for easy cleaning and a reversible drain "T" for vertical or horizontal drainage. The overflow ell has lubricated O-rings for a secure fit, and the hold-down plate is secured with screws for added stability. The drain stopper has a 3/8" rise above the strainer and can be adjusted for clearance if needed.

112035-2-AA (A)
1998 Kohler Co.

 
BEFORE YOU BEGIN
HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based on the latest
product information available at the time of publication.
Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time with-
out notice.
NOTES
Observe all local plumbing and building codes.
Inspect waste and supply tubing; replace if
necessary.
If you are installing a new bath, install the drain
before installing the bath. Refer to the
manufacturers installation instructions.
Adjustable pop-up drain has removable parts.
Drain “T” is reversible for vertical or horizontal
drainage.
ORDERING INFORMATION
2” brass adjustable pop-up drain
for 24” to 26” baths K-7167. . . . . . . . . . . . . . . . . . . . . . . . .
TOOLS REQUIRED
Assorted screwdrivers
Adjustable or open end wrench
Pipe wrenches
Pliers
Plumbers putty
ROUGHING-IN
Fig. #1
3-1/2”
3”
2” N.P.S.
2” O.D.
7”
24” BATH = 21-1/2”
26” BATH = 23-3/4”
18
2
112035-2-AA (A)
Kohler Co., Kohler, WI
INSTALLATION
Apply a ring of plumbers putty or other sealant around
underside of strainer according to the putty
manufacturers instructions. Set flat, gasket between
drain ell and the bottom of the bath. Turn strainer into drain
ell.
Fig. #2
Drain Ell
Gasket
Strainer
Bath
Plumbers putty
Tighten drain ell securely by inserting pliers handles into
top of strainer as shown. The handles will catch on bosses
inside of strainer as the strainer is turned into drain ell.
Make sure drain ell tube is facing the front of bath.
Remove excess sealant.
Fig. #3
Attach the gasket to the overflow ell as shown. Make sure
that the tapered end of the gasket is facing up.
Lubricate O-rings on overflow ell and insert into tube.
Align overflow ell with overflow hole in bath.
Fig. #4
Overflow Ell
Gasket
Tube
From inside the bath, assemble hold down plate to
overflow ell with screws provided. Tighten all screws.
Fig. #5
Hold Down Plate
3
112035-2-AA (A)
Kohler Co., Kohler, WI
Assemble nut and gasket on drain ell, and nut, washer
and cone washer on tube. Align parts with tee as shown.
Insert tubes completely into tee. Align and tighten the
nuts.
Attach tailpiece to tee and tighten, Tailpiece may need to
be cut for proper fit. 1” to 2” of tailpiece should fit inside the
trap. Install bath according to manufacturers installation
instructions. Make sure the tailpiece on the drain fits
properly into the trap.
Fig. #6
Tube
Nuts
Drain Ell
Tee
Gasket
Cone
Washer
Washer
FOR ABOVE FLOOR INSTALLATIONS: Assemble as
shown, following preceding instructions.
Fig. #7
Tube
Nuts
Drain Ell
Tee
Gasket
Cone
Washer
Washer
If necessary, loosen the screw and adjust linkage to the
proper bath size. The screw should be lined up on the 16
for the 16” bath, 14 for the 14” bath, etc. Refer to the bath
installation instructions to determine your bath size.
Tighten screw after adjusting.
Fig. #8
Insert lift rod assembly into overflow ell. Tighten overflow
hood to overflow ell with the two screws provided.
Fig. #9
Assemble handle to overflow hood with phillips screw
provided. It may be necessary to adjust handle to a
desired position.
Fig. #10
Handle
Overflow
Hood
4
112035-2-AA (A)
Kohler Co., Kohler, WI
Insert drain stopper into drain ell.
Fig. #11
Drain stopper should rise approximately 3/8” above
strainer.       
       
     
Fig. #12
Nut
Stopper
Toggle
If sufficient clearance cannot be obtained by adjusting
stopper, remove lift rod assembly. Loosen screw and slide
adjusting block up on adjusting rail to increase clearance
or down to decrease clearance. Tighten screw and insert
back into overflow ell.
Fig. #13
Lift Rod
Assembly
Screw
Adjusting Block
Adjusting Rail
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kohler K-7167-CP Installation guide

Type
Installation guide
This manual is also suitable for

Kohler K-7167-CP is a 2" brass adjustable pop-up drain designed for use with 24" to 26" baths. It features a removable strainer for easy cleaning and a reversible drain "T" for vertical or horizontal drainage. The overflow ell has lubricated O-rings for a secure fit, and the hold-down plate is secured with screws for added stability. The drain stopper has a 3/8" rise above the strainer and can be adjusted for clearance if needed.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI