Finlux 32FLY189S Owner's manual

Page is loading ...

English - 17 -

Contents

Safety Information ........................................ 18

Getting Started ............................................. 19

Notications & Features & Accessories ................ 19

Features ............................................................... 19

Inserting the Batteries into the Remote ................ 20

Connect Power .................................................... 20

Remote Control ................................................... 21

Connections.......................................................... 22

Media Browser Menu............................................ 23

TV Menu Features and Functions ........................ 24

General TV Operation .......................................... 26

Using the Channel List ......................................... 26

Conguring Parental Settings ............................... 26

Electronic Programme Guide (EPG) .................... 26

Software Upgrade................................................. 27

Troubleshooting & Tips ......................................... 27

AV and HDMI Signal Compatibility ...................... 28

English - 18 -

Safety Information

WARNING: Never let people (including

children) with reduced physical, sensory or

mental capabilities or lack of experience and / or

knowledge use electrical devices unsupervised.

• For ventilation purposes, leave a free space of at

least 10 cm all around the set.

•Do not block ventilation holes.

•Do not place the TV on sloping or unstable surfaces,

the TV may tip over.

• Use this device in moderate climates.

• The power cord plug should be easily accessible. Do

not place the TV, furniture, etc. on the power cord.

A damaged power cord/plug can cause re or give

you an electric shock. Handle the power cord by the

plug, do not unplug the TV by pulling the power cord.

Never touch the power cord/plug with wet hands

as this could cause a short circuit or electric shock.

Never make a knot in the power cord or tie it with

other cords. When damaged it must be replaced,

this should only be done by qualied personnel.

•Do not use this TV in a humid or damp environment.

Do not expose the TV to liquids. In case the cabinet

contacts any liquids unplug the TV immediately

and have it checked by qualied personnel before

operating it any further.

•Do not expose the TV to direct sunlight,

open ames or place it near intense heat

sources such as electric heaters.

• Listening in excessive volumes from earphones and

headphones may cause hearing loss.

• Ensure that no open ame sources, such

as lit candles, are placed on top of the TV.

• To prevent injuries, this TV must be securely

attached to a wall carefully by following the

instructions (if the option is available).

IMPORTANT - Please read these instructions fully before installing or operating

To operate your TV in extreme ambient conditions

may cause the damage of the device.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO

NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

Note: Follow the on screen instructions for operating the

related features.

In extreme weather (storms, lightning) and long

inactivity periods (going on holiday) disconnect

the TV set from the mains. The mains plug is

used to disconnect the TV set from the mains

and therefore it must remain readily operable.

This sign is present wherever there is very

important information regarding the operation

and maintenance of the appliance in the literature

accompanying it.

• Occasionally, a few non-active pixels may appear

on the screen as a xed blue, green or red point.

Please note that this does not affect the performance

of your product. Take care not to scratch the screen

with ngernails or other hard objects.

• Before cleaning, unplug the TV from the wall socket.

Only use a soft, dry cloth while cleaning.

Warning

Serious injury or death risk

Risk of electric shock

Dangerous voltage risk

Caution

Injury or property damage risk

Important

Operating the system correctly

Notice

Additional notes marked

English - 19 -

Environmental Information

This television is designed to consume less energy

to help save the environment. To reduce energy

consumption, you should take the following steps:

If you set the Power Save Mode as Eco, the TV will

switch to energy-saving mode. The Power Save Mode

settings can be found in the ‘Picture’ section of the

Main Menu. Note that some picture settings will be

unavailable to be changed.

If Picture Off is selected, “Screen will be off in

3 seconds.” message will be displayed. Select

PROCEED and press OK to continue. The screen

will be off immediately.

When the TV is not in use, please switch off or

disconnect the TV from the mains plug. This will also

reduce energy consumption.

StandbyNotications

1) If the TV does not receive any input signal (e.g.

from an aerial or HDMI source) for 5 minutes, the TV

will go into standby. When you next switch-on, the

following message will be displayed: “Standby Cause

No Signal” Press OK to continue.

2) If the TV has been left on and not been operated

for a while, the TV will go into standby. When you next

switch-on, the following message will be displayed.

“Standby Cause No Operation” Press OK to

continue.

Features

• Remote controlled colour LED TV.

• Fully integrated digital/cable TV (DVB-T/C).

• HDMI inputs are for connecting a device that has

a HDMI socket.

• USB input.

• OSD menu system.

• Scart socket for external devices (such as DVD

Players, PVR, video games, etc.)

• Stereo sound system.

• Teletext.

• Headphone connection.

• Automatic programming system.

• Manual tuning.

• Automatic power down after up to six hours.

• Sleep timer.

• Child lock.

• Automatic sound mute when no transmission.

• NTSC playback.

• AVL (Automatic Volume Limiting).

• PLL (Frequency Search).

• PC input.

• Plug&Play for Windows 98, ME, 2000, XP, Vista,

Windows 7.

• Game Mode (Optional).

Accessories Included

• Remote Control

• Batteries: 2 x AAA

• Instruction Book

TV Control Switch & Operation

1. Up direction

2. Down direction

3. Programme/Volume / AV / Standby-On selection

switch

The Control button allows you to control the Volume/

Programme/ Source and Standby-On functions of

the TV.

To change volume: Increase the volume by pushing

the button up. Decrease the volume by pushing the

button down.

To change channel: Press the middle of the

button, the channel information banner will appear

on screen. Scroll through the stored channels by

pushing the button up or down

To change source: Press the middle of the button

twice, the source list will appear on screen. Scroll

through the available sources by pushing the button

up or down.

To turn the TV off: Press the middle of the button

down and hold it down for a few seconds, the TV will

turn into standby mode.

Getting Started

Notications&Features&Accessories

English - 20 -

Inserting the Batteries into the Remote

Lift the cover on the back of the remote upward

gently. Install two AAA batteries. Make sure to

match the + and - ends of the batteries in the

battery compartment (observe the correct polarity)

Replace the cover.

Connect Power

IMPORTANT: The TV set is designed to operate on

220-240V AC, 50 Hz socket. After unpacking, allow

the TV set to reach the ambient room temperature

before you connect the set to the mains. Plug the

power cable to the mains socket outlet.

Antenna/Cable Connection

Connect the “aerial” or “cable TV” plug to the AERIAL

INPUT (ANT) socket located on the back of the TV.

Notication

Manufactured under license from Dolby Laboratories.

TRADEMARK ACKNOWLEDGMENT

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

“HDMI, the HDMI logo and High-Denition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.”

Information for Users on Disposal of Old

Equipment and Batteries

[European Union only]

These symbols indicate that equipment with these

symbols should not be disposed of as general

household waste. If you want to dispose of the

product or battery, please consider the collection

systems or facilities for appropriate recycling.

Notice: The sign Pb below the symbol for batteries indicates

that this battery contains lead.

Products

Battery

Specication

TV Broadcasting PAL B/G D/K K I/I’

Receiving Channels

VHF (BAND I/III) - UHF

(BAND U) - HYPERBAND

Number of Preset

Channels

1000

Channel Indicator On Screen Display

RF Aerial Input 75 Ohm (unbalanced)

Operating Voltage 220-240V AC, 50Hz.

Audio German+Nicam Stereo

Audio Output Power

(WRMS.) (10% THD)

2 x 6

Power Consumption 65 W

Weight 6,90

TV Dimensions DxLxH

(with foot)

185x 744 x 494

TV Dimensions DxLxH

(without foot)

90 x 744 x 451

Operation temperature

and operation

humidity:

0ºC up to 40ºC, 85%

humidity max

English - 21 -

1. Standby / On

2. Play (in media browser mode)

3. No function

4. Mono-Stereo Dual I-II / Current language (in

DVB channels)

5. Rapid reverse (in media browser mode)

6. Coloured buttons (Red, Green, Yellow, Blue)

7. Numeric buttons

8. Channel list

9. Navigation buttons

10. OK (Conrm) / Hold (in TXT mode)

11. Menu on / off

12. Return / Back / Index page (in TXT mode)

13. No function

14. Media browser

15. Electronic programme guide (in DVB channels)

16. Teletext / Mix

17. Volume up / down

18. Mute button

19. Programme up / down

20. Image size

21. Info / Reveal (in TXT mode)

22. My button 1 (*)

23. My button 2 (**)

24. Exit

25. Quick Menu

26. Previous programme

27. Rapid advance (in media browser mode)

28. Subtitle on-off (in DVB channels & media

browser mode)

29. Stop (in media browser mode)

30. Pause (in media browser mode)

31. AV / Source

MY BUTTON 1

Press MY BUTTON 1 for ve seconds when on a

desired source, channel or link, until the “MY BUTTON

IS SET” message is displayed on the screen. This

confirms that the selected MY BUTTON is now

associated with the selected function.

Teletext

Press “ ” button to enter. Press again to activate mix

mode. Press once more to exit. Follow the instructions

displayed on digital teletext screen.

Digital Teletext (for UK only)

Press “ ” button to view digital teletext information.

Operate it with the coloured buttons, cursor buttons

and the OK button. The operation method may differ

depending on the contents of the digital teletext. Follow

the instructions displayed on the digital teletext screen.

When the “ ” button is pressed again, the TV returns

to television broadcast.

Getting Started

Remote Control

MY BUTTON 2

This button's main function is to switch between

DVB-T, DVB-C and DVB-S broadcasts. However, if

you press MY BUTTON 2 for ve seconds, you can

set a function to it as described in My Button 1.

Note that if you perform rst time installation, MY

BUTTON 2 will return to its default function, switching

between DVB-T, DVB-C and DVB-S broadcasts.

4

7

8

9

P+

P-

V+

V-

1

.,/@

2

3

5

6

0

OK

Q.MENU

EXIT

BACK

LANG.

SOURCE

2

/

1

/

English - 22 -

NOTE: When connecting a device via the Side AV input, you must use a connection cable to enable

connection. See the illustrations above. To enable PC audio, you will need to use the SIDE AV CONNECTION

cable’s WHITE & RED inputs. If an external device is connected via the SCART socket, the TV will automatically

switch to AV mode.When receiving DTV channels (Mpeg4 H.264) or while in Media Browser mode, output will not

be available via the scart socket. When using the wall mounting kit (optional), we recommend that you plug all

your cables into the back of the TV before mounting on the wall.Insert or remove the CI module only when the TV

is SWITCHED OFF. You should refer to the module instruction manual for details of the settings.

Connector Type Cables Device

Scart

Connection

(back)

VGA

Connection

(back)

SIDE AV

PC/YPbPr

Audio

Connection

(side)

Side Audio

YPbPr or PCConnection Cable

HDMI

Connection

(back)

SPDIFF

Connection

(back)

SIDE AV

Side AV

(Audio/Video)

Connection

(side)

HEADPHONE

Headphone

Connection

(side)

YPBPR

YPbPr Video

Connection

(side)

YPbPr Connection

Cable

USB

Connection

(side)

CI

Connection

(side)

CAM

module

Getting Started

Connections

English - 23 -

Switching On/Off

To Switch the TV On

Connect the power cord to the 220-240V AC, 50 Hz.

To switch on the TV from standby mode either:

Press the “ ” button, P+ / P- or a numeric button on

the remote control.

Press the side function switch until the TV comes on

from standby.

To Switch the TV Off

Press the “ “ button on the remote control or press the

side function switch until the TV switches into standby

mode.

To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched to standby mode, the standby

LED can blink to indicate that features such as Standby Search,

Over Air Download or Timer is active. The LED can also blink

when you switch on the TV from standby mode.

First Time Installation

When turned on for the first time, the language

selection screen is displayed. Select the desired

language and press OK.

The First Time Installation (FTI) screen will be

displayed next. Set your preferences using the

navigation buttons and when nished, press OK to

continue.

You can activate Store mode option to be available

in “Other settings” menu and your TV’s features will

be illustrated on the top of the screen. A conrmation

screen will be displayed. Select YES to proceed.

If Home Mode is selected, Store mode will not be

available after the First Time Installation. Press OK

button to continue.

Aerial Installation

If you select AERIAL option from the Search Type

screen, the television will search for digital terrestrial

TV broadcasts.

NOTE: You can press MENU button to cancel.

After all the available stations are stored, the

Channel List will be displayed on the screen. If

you like how the channels are sorted according to

the LCN (*), please select “Yes” and than press OK.

Press MENU button to quit channel list and watch TV.

(*) LCN is the Logical Channel Number system that

organizes available broadcasts in accordance with a

recognizable channel sequence (if available).

Cable Installation

If you select CABLE option and press OK button on the

remote control. To continue, please select YES and

press OK. To cancel operation, select NO and press

OK. You can select frequency ranges from this screen.

Enter the frequency range manually by using the

numeric button.

Note: Searching duration will change depending on

the selected search step.

Media Playback via USB Input

You can connect a 2.5” and 3.5” inch (hdd with external

power supply) external hard disk drives or USB memory

stick to your TV by using the USB inputs of the TV.

IMPORTANT! Back up your les before making

any connections to the TV. Manufacturer will not

be responsible for any le damage or data loss.

Certain types of USB devices (e.g. MP3 Players)

or USB hard disk drives/memory sticks may not be

compatible with this TV. The TV supports FAT32

and NTFS disk formatting.

While formatting a USB hard disk that has 1TB (Tera

Byte) or more le capacity, you can experience

problems with the formatting process. Do not

repeatedly quickly plug and unplug the drive. This

may cause physical damage to the USB player

and USB device itself. Do not pull out USB module

while playing a le.

Media Browser Menu

You can play photo, music, and movie les stored on a

USB disk by connecting it to your TV. Connect a USB

disk to one of the USB inputs located on the side of

the TV. Pressing the MENU button while in the Media

Browser mode will access the Picture, Sound and

Settings menu options. Pressing the MENU button

again will exit from this screen. You can set your Media

Browser preferences by using the Settings Menu.

Loop/Shufe Mode Operation

Start playback with and

activate

TV plays next file and loop

the list.

Start playback with OK and

activate

The same le will be played in

a loop (repeat).

Start playback with OK/ and

activate

The file will be played in a

shufe.

Quick Menu

Quick Settings menu allows you to access some

options quickly. This menu includes Power Save

Mode, Picture Mode, Equalizer Settings, Favourites

and Sleep Timer options. Press Q.MENU button

on the remote control to view quick menu. See the

following chapters for the details of the listed features.

Getting Started

First Time Installation - USB Connections

English - 24 -

TV Menu Features and Functions

Picture Menu Contents

Mode

You can change the picture mode to suit your preference or requirements. Picture mode

can be set to one of these options: Cinema,Game,Dynamic and Natural.

Contrast Sets the lightness and darkness values of the screen.

Brightness Sets the brightness value for the screen.

Sharpness Sets the sharpness value for the objects displayed on the screen.

Colour Sets the colour value, adjusting the colors.

Power Save

Mode

To set the Power Save Mode as Eco, Picture Off and Disabled.

(When the Mode is Dynamic, Power Save mode is automatically set as disabled.)

Backlight

(Optional)

This setting controls the backlight level. The backlight function will be inactive if the Power

Save Mode is set to Eco. The backlight cannot be activated in VGA, Media Browser mode

or while the picture mode is set to Game.

Noise

Reduction

If the broadcast signal is weak and the picture is noisy, use the Noise Reduction

setting to reduce the amount of noise.

Advanced Settings

Dyanmic

Contrast

You can change the Dynamic Contrast ratio to desired value.

Colour Temp Sets the desired colour tone.

Picture Zoom

Sets the desired picture size from picture zoom menu.

Note: Auto (Only available in Scart mode with SCART PIN8 high voltage/low voltage

switching)

Film Mode

Films are recorded at a different number of frames per second to normal television

programmes. Turn this feature on when you are watching films to see the fast

motion scenes clearly.

Skin Tone Skin tone can be changed between -5 and 5.

Colour Shift Adjusts the desired colour tone.

RGB Gain You can congure the colour temperature values using the RGB Gain feature.

Reset Resets the picture settings to factory default settings.(Except Game Mode)

Autoposition

(in PC mode)

Automatically optimizes the display. Press OK to optimize.

H Position (in

PC mode)

This item shifts the image horizontally to the right hand side or left hand side of the screen.

V Position (in

PC mode)

This item shifts the image vertically towards the top or bottom of the screen.

Dot Clock (in

PC mode)

Dot Clock adjustments correct the interference that appear as vertical banding in dot

intensive presentations like spreadsheets or paragraphs or text in smaller fonts.

Phase (in PC

mode)

Depending on the resolution and scan frequency that you input to the TV set, you may

see a hazy or noisy picture on the screen. In such a case you can use this item to get a

clear picture by trial and error method.

While in VGA (PC) mode, some items in Picture menu will be unavailable. Instead, VGA mode

settings will be added to the Picture Settings while in PC mode.

English - 25 -

Sound Menu Contents

Volume Adjusts the volume level.

Equalizer

Selects the equalizer mode. Custom settings can be made only when

in user mode.

Balance This setting is used for emphasizing left or right speaker balance.

Headphone Sets headphone volume.

Sound Mode You can select a sound mode. (If the selected channel supports).

AVL (Automatic

Volume Limiting)

Function sets the sound to obtain xed output level between programmes.

Digital Out Sets digital out audio type.

Settings Menu Contents

Conditional Access Controls conditional access modules when available.

Language

Congures language settings (may change depending on the country selected)

Preferred and current settings will be available. Current settings can be

changed only if the broadcaster supports.

Parental

Enter correct password to change parental settings. You can easily adjust

menu lock, maturity lock(may change depending on the country selected) and

child lock in this menu. You can also set new pin number.

Timers

Sets sleep timer to turn off the TV after a certain time. Sets timers for selected programmes.

(USB Record)

Date/Time Sets date and time.

Sources Enables or disables selected source options.

Other Settings: Displays other setting options of the TV set:

Menu Timeout Changes timeout duration for menu screens.

Scan Encrypted

Channels

When this setting is on, the search process will locate the encrypted channels as well.

Blue Background Activates or deactivates the blue background system when the signal is weak or absent.

Software Upgrade To ensure that your TV always has the most up to date rmware.

Application Version Displays application version.

Hard of Hearing Enables any special feature sent from the broadcaster.

Audio Description

Audio description refers to an additional narration track for blind and visually

impaired viewers of visual media, including television and movies. You can use

this feature, only if the broadcaster supports that additional narration track.

Note: Audio description sound feature cannot be available in recording or time

shifting mode..

Auto TV Off

You can set the timeout value of auto off feature. When the timeout value is reached

and the TV has not been operated for a selected time, the TV will go into standby mode.

Standby Search

(Optional)

If the Standby Search is set to On, when the TV is in standby mode, available

broadcasts will be searched. If the TV locates any new or missing broadcasts, a

menu screen will be displayed, asking you whether or not to execute these changes.

Channel list will be updated and changed after this process.

English - 26 -

Store Mode

If you are displaying the TV in a store, you can activate this mode. Whilst Store

Mode is enabled, some items in the TV menu may not be available.

Power Up Mode This setting confrigures the power up mode preference.

Install and Retune Menu Contents

Automatic Channel

Scan (Retune)

(If available)

Displays automatic tuning options.

Digital Aerial: Searches and stores aerial DVB stations.

Digital Cable: Searches and stores cable DVB stations.

Analogue: Searches and stores analogue stations.

Digital Aerial & Analogue: Searches and stores aerial DVB and analogue

stations.

Digital Cable & Analogue: Searches and stores cable DVB and analogue

stations.

Manual Channel Scan This feature can be used for direct broadcast entry.

Network Channel Scan Searches for the linked channels in the broadcast system.

Analogue Fine Tune

You can use this setting for ne tuning analogue channels. This feature is not

available if no analogue channels are stored.

First Time Installation Deletes all stored channels and settings, resets TV to factory settings.

The TV sorts all stored stations in the Channel List.

You can edit this channel list, set favourites or set

active stations to be listed by using the Channel List

options.

ConguringParentalSettings

To prohibit viewing of certain programmes, channels and

menus can be locked by using the parental control system.

To display parental lock menu options, the PIN number

should be entered. The factory default PIN number is

0000. After coding the correct PIN number, parental

settings menu will be displayed.

Menu Lock: Menu lock setting enables or disables

the menu access.

Maturity Lock: When set, this option gets the maturity

information from the broadcast and if this maturity

level is disabled, disables access to the broadcast.

Child Lock: When Child Lock is set, the TV can only

be controlled by the remote control. In this case the

control panel buttons will not work.

Set PIN: Denes a new PIN number.

Note: If the Country option is set to France, you can use 4725

as the default code.

General TV Operation

Using the Channel List

Electronic Programme Guide (EPG)

Some, but not all channels send information about the

current and next programmes. Press the “ ” button

to view the EPG menu.

Red button (Prev Day): Displays the programmes of

previous day.

Green button (Next day): Displays the programmes

of the next day.

Yellow button (Zoom): Expands programme information.

Blue button (Filter): Views ltering options.

: Press “ ” button to view Select Genre menu.

Using this feature, you can search the programme guide

database in accordance with the genre. Info available

in the programme guide will be searched and results

matching your criteria will be listed.

(i) INFO: Displays, in detailed, information on the

programme selected.

Numeric buttons (Jump): Jumps to the preferred

channel directly via numeric buttons.

OK: Displays programme options.

Text (Search): Displays “Guide Search” menu.

(Now) : Shows the current programme.

P+P- : More event info

IMPORTANT: Connect a USB disk to your TV while the TV

is switched off. You should then switch on the TV to enable

the recording feature.

English - 27 -

Note: Switching to a different broadcast or source is not

available during a recording.

Programme Options

In EPG menu, press the OK button to enter the

Event Options menu.

Select Channel

In EPG menu, using this option, you can switch

to the selected channel.

Set Timer / Delete Timer

After you have selected a programme in the EPG

menu, press the OK button. Select the Set Timer

on Event option and press the OK button. You

can set a timer for future programmes. To cancel

an already set timer, highlight that programme and

press the OK button. Then select “Delete Timer”

option. The timer will be cancelled.

Software Upgrade

Your TV is capable of finding and updating

automatically via the Aerial/Cable signal.

Software upgrade search via user

interface

Simply navigate on your main menu. Choose

Settings and select Other Settings menu. In Other

Settings menu navigate on to the Software for

Upgrade item and press OK button to check for a

new software upgrade.

3 AM search and upgrade mode

While the TV is connected to an aerial signal. If

Automatic scanning in the Upgrade Options menu

is enabled, the TV wakes up at 03:00 and searches

broadcast channels for new software upgrades. If

new software is found and downloaded successfully,

the next time the TV powers up , it will have the new

software version.

Note: If the TV fails to come on after the upgrade unplug the

TV for 2 minutes and plug in again.

Troubleshooting & Tips

Tv will not turn on

Make sure the power cord is plugged in securely to

wall outlet. The batteries in the remote control may be

exhausted. Press the Power button on the TV.

Poor picture

• Have you selected the correct TV system?

• Low signal level can cause picture distortion.Please

check antenna access.

• Check if you have entered the correct channel

frequency if you have done manual tuning.

• The picture quality may degrade when two devices

are connected to the TV at the same time. In such

a case, disconnect one of the devices.

No picture

• No Picture means that your TV is not receiving a

transmission. Have you selected the correct button on

the remote control? Try once more. Also make sure

the correct input source has been selected.

• Is the antenna connected properly?

• Is the antenna cable damaged?

• Are suitable plugs used to connect the antenna?

• If you are in doubt, consult your dealer.

No sound

• Has the TV been set to mute? To cancel mute, press the

“ ” button, or increase the volume level.

• Sound is coming from only one speaker. Is the balance

set to one extreme? See Sound Menu section.

Remote control - does not operate

• The batteries may be exhausted. Replace the

bateries.

Input sources - can not be selected

• If you cannot select an input source, it is possible that

no device is connected. if not

• Check the AV cables and connections if you have tried

to connect a device.

English - 28 -

Source Supported Signals Available

EXT

(SCART)

PAL 50/60 O

NTSC 60 O

RGB 50 O

RGB 60 O

Side AV

PAL 50/60 O

NTSC 60 O

PC/

YPbPr

480I, 480P 60Hz O

576I, 576P 50Hz O

720P 50Hz,60Hz O

1080I 50Hz,60Hz O

1080P 50Hz,60Hz O

HDMI1

480I 60Hz O

480P 60Hz O

576I, 576P 50Hz O

720P 50Hz,60Hz O

1080I 50Hz,60Hz O

1080P

24Hz, 25Hz

30Hz, 50Hz,

60Hz

O

(X: Not Available, O: Available)

In some cases a signal on the LED TV may not be displayed

properly. The problem may be an inconsistency with

standards from the source equipment (DVD, Set-top box, etc.

). If you do experience such a problem please contact your

dealer and also the manufacturer of the source equipment.

AV and HDMI Signal Compatibility

Supported File Formats for USB Mode

Media File Extension

Format

Remarks

(Maximum resolution/Bit rate etc.)

Video

Audio

Movie

mpg, mpeg MPEG1, MPEG2

MPEG1: 768x576 @30P

MPEG2:1920x1080 @ 30P

vob MPEG2

1920x1080 @ 30P

mp4 MPEG4, Xvid , H.264

mkv

H.264, MPEG4,VC-1

avi MPEG2, MPEG4, Xvid , H.264

v H.264/VP6/Sorenson

H.264/VP6:1920x1080 @ 30P

Sorenson: 352x288 @30P

3gp MPEG4 , H.264 1920x1080 @ 30P

Music

.mp3 -

MPEG 1 Layer 2

32Kbps ~ 448Kbps(Bit rate)

32K, 44.1k, 48k Hz,16K, 22.05K, 24K Hz (Sampling

rate)

MPEG 1 Layer 3

32Kbps ~ 320Kbps(Bit rate)

32K, 44.1k, 48k Hz,16K, 22.05K, 24K Hz,8K, 11.025K,

12K Hz (Sampling rate)

Photo

.jpg .jpeg

Baseline JPEG

-

max WxH = 17000x10000 4147200bytes

.

Progressive JPEG

-

max WxH = 4000x4000 3840000bytes

.bmp - - max WxH = 5760x4096 3840000bytes

Subtitle

.sub .srt

-

PC Input Typical Display Modes

The following table is an illustration of some of the typical video

display modes. Your TV may not support all resolutions. Your TV

supports up to 1920x1080.

Index Resolution Frequency

1 1024x768 60 Hz

2 1280x768 60 Hz

3 1360x768 60 Hz

4 800x600 56 Hz

5 800x600 60 Hz

6 1024x768 66 Hz

7 1280x960 60 Hz

8 1280x1024 60 Hz

9 1400x1050 60 Hz

10 1600x1200 60 Hz

11 1920x1080 60 Hz

Page is loading ...

Finlux 32FLY189S Owner's manual

Finlux 32FLY189S Owner's manual

in other languages

Related papers

Other documents