South bend SB1101 Owner's manual

SINCE

1906

SINCE

1906

MODEL SB1100/SB1101

***IMPORTANT UPDATE***

WARNING: No portion of this manual may be reproduced without written approval.

#JM22435 Printed in Taiwan

Applies to Models Mfd. Since 01/22

and Owner’s Manual Revised 05/21

The following change was made to this machine since the owner’s manual was printed:

• The inlet adapter has changed.

Aside from this information, all other content in the owner’s manual applies and MUST be read and

understood for your own safety. IMPORTANT: Keep this update with the owner’s manual for

future reference.

If you have any further questions about this manual update or the changes made to the machine,

contact our Technical Support at (360) 734-1540 or email www.southbendtools.com.

READ THIS FIRST

New Inlet Adapter

Old Inlet Adapter

4V2

SB1100 Revised Parts

REF PART # DESCRIPTION

4V2 PSB1100004V2 INLET ADAPTER 6" X 4" X 3 (PC) V2.01.22

14V2

SB1101 Revised Parts

REF PART # DESCRIPTION

14V2 PSB1101014V2 INLET ADAPTER 7" X 4" X 3 (PC) V2.01.22

®

A Tradition of Excellence

South Bend Tools

MODELS SB1100 & SB1101

SINGLE-STAGE DUST COLLECTORS

OWNER'S MANUAL

Customer Service

We stand behind our machines. If you have any service questions, parts requests or general questions

about your purchase, feel free to contact us.

South Bend Tools

P.O. Box 2027

Bellingham, WA 98227

Phone: (360) 734-1540

Fax: (360) 676-1075 (International)

Fax: (360) 734-1639 (USA Only)

Email: [email protected]

Updates

For your convenience, any updates to this manual will be available to download free of charge

through our website at:

www.southbendtools.com

Scope of Manual

This manual helps the reader understand the machine, how to prepare it for operation, how to control

it during operation, and how to keep it in good working condition. We assume the reader has a basic

understanding of how to operate this type of machine, but that the reader is not familiar with the

controls and adjustments of this specific model. As with all machinery of this nature, learning the

nuances of operation is a process that happens through training and experience. If you are not an

experienced operator of this type of machinery, read through this entire manual, then learn more

from an experienced operator, schooling, or research before attempting operations. Following this

advice will help you avoid serious personal injury and get the best results from your work.

Manual Feedback

We've made every effort to be accurate when documenting this machine. However, errors sometimes

happen or the machine design changes after the documentation process—so

the manual may not

exactly match your machine.

If a difference between the manual and machine leaves you in doubt,

contact our

customer service for clarification.

We highly value customer feedback on our manuals. If you have a moment, please share your

experience using this manual. What did you like about it? Is there anything you would change to

make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use?

South Bend Tools

C

/O Technical Documentation Manager

P.O. Box 2027

Bellingham, WA 98227

Email: [email protected]

Table of Contents

OPERATION .................................................................... 32

Operation Overview ...........................................32

ACCESSORIES ..............................................................33

MAINTENANCE .............................................................36

Maintenance Schedule .......................................36

Cleaning Canister Filter....................................36

Removing/Replacing Collection Bag .................37

Removing/Replacing Canister Filter ................37

SERVICE........................................................................... 41

Pairing Remote Control & Receiver ..................41

TROUBLESHOOTING ................................................. 42

ELECTRICAL ................................................................... 44

Electrical Safety Instructions ...........................44

SB1100 Wiring Diagram ...................................45

SB1100 Electrical Component Pictures ............46

SB1101 Wiring Diagram ...................................48

SB1101 Electrical Component Pictures ............49

PARTS................................................................................ 51

SB1100 Main ......................................................51

SB1101 Main ......................................................53

Canister Filter....................................................55

Machine Labels ..................................................56

WARRANTY ..................................................................... 57

INTRODUCTION ............................................................... 2

Identiﬁcation ........................................................ 2

Description of Controls & Components ..............3

Product Speciﬁcations .........................................4

SAFETY ................................................................................7

Understanding Risks of Machinery ....................7

Basic Machine Safety ..........................................7

Additional Dust Collector Safety ........................9

PREPARATION .............................................................. 10

Preparation Overview ........................................10

Required for Setup .............................................10

Power Supply Requirements ............................. 11

Unpacking ..........................................................13

SB1100 Inventory ..............................................13

SB1101 Inventory ..............................................14

Hardware Recognition Chart ............................15

Location ..............................................................16

Assembly ............................................................17

Test Run .............................................................22

SYSTEM DESIGN .........................................................23

General ...............................................................23

Duct Material ..................................................... 23

System Design ....................................................25

System Grounding .............................................31

INTRODUCTIOn

-2-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 INTRODUCTION

Identiﬁcation

Inlet Inlet

PortPort

InletInlet

AdapterAdapter

Canister Canister

FilterFilter

SwivelSwivel

CasterCaster

Filter BrushFilter Brush

MotorMotor

CollectionCollection

BagBag

SwitchSwitch

BoxBox

Pressure Pressure

GaugeGauge

Serious personal injury could occur if

you connect the machine to power before

completing the setup process. DO NOT

connect power until instructed to do so later

in this manual.

Untrained users have an increased risk

of seriously injuring themselves with this

machine. Do not operate this machine until

you have understood this entire manual and

received proper training.

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-3-

INTRODUCTION

Description of Controls

& Components

CC

DD

EE

FF

GG

Figure Figure 1. SB1100 & SB1101 components.. SB1100 & SB1101 components.

Figure Figure 2. SB1100 & SB1101 remote control.

Refer to Figures 1-2 and the following

descriptions to become familiar with the basic

controls and components used to operate this

machine.

A. Switch Box: Controls motor operation with a

thermally protected magnetic switch. Houses

an RF receiver for remote control operation.

B. Start Button: Turns machine ON.

C. Emergency Stop Button: Turns machine

OFF and prevents it from starting. Turn

button clockwise to reset.

D. Filter Brush Motor: Turns ON for

approximately 90 seconds after main motor

is turned OFF. Knocks dust cake off filter

pleats, cleaning filter and maintaining air

flow. Filter brush motor run time can be

changed at timer inside switch box (refer to

Wiring on Page 44).

E. Pressure Gauge: Displays vacuum pressure,

indicating when filter and collection bags

need to be cleaned or replaced. Clean filter

when operating pressure drops below

200mmAq. If operating pressure reaches

150mmAq and cleaning does not improve

performance, replace the filter.

F. Collection Bag: Collects fine dust particles

from filter.

G. Remote Control: Green button turns motor

ON. Red button turns motor OFF. Requires

a 12V, type A27 battery.

Note: The remote control operates on radio

frequency and has a 75-ft. range. It does not

need to be aimed at the switch box to operate.

AA

BB

-4-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 INTRODUCTION

Product Speciﬁcations

Model SB1100 & SB1101

Cyclone Dust Collectors

Product Specifications

P.O. Box 2027, Bellingham, WA 98227 U.S.A.

www.southbendtools.com

PHONE: (360) 734-1540 • © South Bend Tools

Model Number SB1100 SB1101

Product Dimensions

Weight 157 lbs 208 lbs.

Width x Depth x Height 39 x 31-1/2 x 76 in. 58 x 31-1/2 x 76 in.

Footprint (Length/Width) 33-1/2 x 21-1/2 in. 49-1/2 x 21-1/2 in.

Shipping Dimensions

Carton #1 Type Cardboard Box

Weight 131 lbs. 169 lbs.

Length x Width x Height 23 x 36 x 23 in. 52 x 23 x 23 in.

Carton #2 Type Cardboard Box (Canister Filter)

Weight 34 lbs

Length x Width x Height 22 x 22 x 32 in.

Carton #3 Type N/A Cardboard Box (Canister Filter 2)

Weight N/A 34 lbs

Length x Width x Height N/A 22 x 22 x 32 in.

Operation

Dust Collector Type Single-Stage

Approved Dust Types Wood

Filter Type Pleated Cartridge

Airflow Performance 1103 CFM @ 3.5 in. SP 1429 CFM @ 3.2 in. SP

Max Static Pressure (at 0 CFM) 11.95 in. 12 in.

Main Inlet Size 6 in. 7 in.

Number of Adapter Inlets 3 3

Adapter Inlet Size 4 in. 4 in.

Machine Collection Capacity at One

Time 3 3

Maximum Material Collection

Capacity 33-1/2 Gallons 67 Gallons

Filtration Rating 1 Micron 1 Micron

Filter Surface Area 80 sq. ft. 160 sq. ft.

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-5-

INTRODUCTION

Model Number SB1100 SB1101

Electrical

Power Requirement 220V, Single-Phase, 60 Hz 240V, Single-Phase, 60 Hz

Full-Load Current Rating 9A 12A

Minimum Circuit Size 15A 20A

Connection Type Cord & Plug

Power Cord Included Yes Yes

Power Cord Length 65 in. 64 in.

Power Cord Gauge 14 AWG

Plug Included Yes

Included Plug Type 6-15 6-20

Switch Type Remote Control Magnetic Switch w/Overload Protection

Main Motor

Type TEFC Capacitor-Start Induction

Horsepower 2 HP 3 HP

Phase Single-Phase

Amps 9A 12A

Speed 3450 RPM

Power Transfer Direct

Bearings Shielded & Permanently Lubricated

Centrifugal Switch/Contacts Type External

Filter Brush Motor

Type TENV Induction

Horsepower 6W

Phase Single-Phase

Amps 0.15A

Speed 1600 RPM

Power Transfer Direct

Bearings Shielded & Permanently Lubricated

Centrifugal Switch/Contacts Type External

Filter Brush Motor 2

Type N/A TENV Induction

Horsepower N/A 6W

Phase N/A Single-Phase

Amps N/A 0.15A

Speed N/A 1600 RPM

Power Transfer N/A Direct

Bearings N/A Shielded & Permanently Lubricated

Centrifugal Switch/Contacts Type N/A External

-6-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 INTRODUCTION

Model Number SB1100 SB1101

Bag Information

Number of Filter Bags 1 2

Filter Bag Diameter 19-1/2 in.

Filter Bag Length 37 in.

Canister Information

Number of Canister Filters 1 2

Canister Filter Diameter 19-5/8 in.

Canister Filter Length 29 in.

Impeller Information

Impeller Type Radial Fan

Impeller Size 12-3/4 in. 12-3/4 in.

Impeller Blade Thickness 1/8 in. 1/8 in.

Construction

Filter Collection Bag Clear Plastic

Canister Spun Bond Polyester

Base Steel

Caster Plastic

Impeller Aluminum

Paint Type/Finish Powder Coated

Blower Housing Steel

Body Steel

Manufacturer Specifications

Country of Origin Taiwan

Warranty 1 Year

Approximate. Assembly & Setup Time 45 Minutes 1 Hour

Serial Number Location ID Label

Sound Rating N/A

SAFETY

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-7-

SAFETY

Understanding Risks of Machinery

Operating all machinery and machining equipment can be dangerous or relatively safe depending

on how it is installed and maintained, and the operator's experience, common sense, risk awareness,

working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).

The owner of this machinery or equipment is ultimately responsible for its safe use. This

responsibility includes proper installation in a safe environment, personnel training and usage

authorization, regular inspection and maintenance, manual availability and comprehension,

application of safety devices, integrity of cutting tools or accessories, and the usage of approved

personal protective equipment by all operators and bystanders.

The manufacturer of this machinery or equipment will not be held liable for injury or property

damage from negligence, improper training, machine modiﬁcations, or misuse. Failure to read,

understand, and follow the manual and safety labels may result in serious personal injury, including

amputation, broken bones, electrocution, or death.

The signals used in this manual to identify hazard levels are as follows:

Death or catastrophic

harm WILL occur.

Moderate injury or ﬁre

MAY occur.

Death or catastrophic

harm COULD occur.

Machine or property

damage may occur.

Basic Machine Safety

Owner’s Manual: All machinery and machining

equipment presents serious injury hazards

to untrained users. To reduce the risk of

injury, anyone who uses THIS item MUST

read and understand this entire manual

before starting.

Personal Protective Equipment: Operating or

servicing this item may expose the user

to ﬂying debris, dust, smoke, dangerous

chemicals, or loud noises. These hazards

can result in eye injury, blindness, long-

term respiratory damage, poisoning,

cancer, reproductive harm or hearing loss.

Reduce your risks from these hazards

by wearing approved eye protection,

respirator, gloves, or hearing protection.

Trained/Supervised Operators Only: Untrained

users can seriously injure themselves

or bystanders. Only allow trained and

properly supervised personnel to operate

this item. Make sure safe operation

instructions are clearly understood. If

electrically powered, use padlocks and

master switches, and remove start switch

keys to prevent unauthorized use or

accidental starting.

Guards/Covers: Accidental contact with

moving parts during operation may cause

severe entanglement, impact, cutting,

or crushing injuries. Reduce this risk by

keeping any included guards/covers/doors

installed, fully functional, and positioned

for maximum protection.

-8-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 SAFETY

Entanglement: Loose clothing, gloves, neckties,

jewelry or long hair may get caught in

moving parts, causing entanglement,

amputation, crushing, or strangulation.

Reduce this risk by removing/securing

these items so they cannot contact moving

parts.

Mental Alertness: Operating this item with

reduced mental alertness increases the

risk of accidental injury. Do not let a

temporary influence or distraction lead to a

permanent disability! Never operate when

under the influence of drugs/alcohol, when

tired, or otherwise distracted.

Safe Environment: Operating electrically

powered equipment in a wet environment

may result in electrocution; operating near

highly ﬂammable materials may result in a

ﬁre or explosion. Only operate this item in

a dry location that is free from ﬂammable

materials.

Electrical Connection: With electically powered

equipment, improper connections to the

power source may result in electrocution

or fire. Always adhere to all electrical

requirements and applicable codes when

connecting to the power source. Have all

work inspected by a qualified electrician to

minimize risk.

Disconnect Power: Adjusting or servicing

electrically powered equipment while it

is connected to the power source greatly

increases the risk of injury from accidental

startup. Always disconnect power

BEFORE any service or adjustments,

including changing blades or other tooling.

Secure Workpiece/Tooling: Loose workpieces,

cutting tools, or rotating spindles can

become dangerous projectiles if not

secured or if they hit another object during

operation. Reduce the risk of this hazard

by verifying that all fastening devices are

properly secured and items attached to

spindles have enough clearance to safely

rotate.

Chuck Keys or Adjusting Tools: Tools used to

adjust spindles, chucks, or any moving/

rotating parts will become dangerous

projectiles if left in place when the machine

is started. Reduce this risk by developing

the habit of always removing these tools

immediately after using them.

Work Area: Clutter and dark shadows increase

the risks of accidental injury. Only operate

this item in a clean, non-glaring, and well-

lighted work area.

Properly Functioning Equipment: Poorly

maintained, damaged, or malfunctioning

equipment has higher risks of causing

serious personal injury compared to

those that are properly maintained.

To reduce this risk, always maintain

this item to the highest standards and

promptly repair/service a damaged or

malfunctioning component. Always follow

the maintenance instructions included in

this documentation.

Unattended Operation: Electrically powered

equipment that is left unattended while

running cannot be controlled and is

dangerous to bystanders. Always turn the

power OFF before walking away.

Health Hazards: Certain cutting fluids and

lubricants, or dust/smoke created when

cutting, may contain chemicals known to

the State of California to cause cancer,

respiratory problems, birth defects,

or other reproductive harm. Minimize

exposure to these chemicals by wearing

approved personal protective equipment

and operating in a well ventilated area.

Difﬁcult Operations: Attempting difficult

operations with which you are unfamiliar

increases the risk of injury. If you

experience difficulties performing the

intended operation, STOP! Seek an

alternative method to accomplish the

same task, ask a qualified expert how the

operation should be performed, or contact

our Technical Support for assistance.

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-9-

SAFETY

Additional Dust Collector Safety

Power Disconnect. Turn machine OFF,

disconnect from power supply, and

allow impeller to completely stop before

leaving machine unattended, or doing any

maintenance or service.

Regular Cleaning. To reduce risk of starting

a fire, regularly check/empty collection

bags or drum to avoid buildup of fine dust,

which can increase risk of fire. Regularly

clean surrounding area where machine

is operated—excessive dust buildup on

overhead lights, heaters, electrical panels, or

other heat sources will increase risk of fire.

Suspended Dust Particles. To reduce risk of

death or injury caused by explosions or fires,

DO NOT operate in areas where these risks

are high, including spaces near pilot lights,

open flames, or other ignition sources.

Avoiding Sparks. To reduce risk of fire, avoid

collecting any metal objects or stones. These

can possibly produce sparks when they

strike impeller, which can smolder in wood

dust for a long time before a fire is detected.

If you accidentally cut into wood containing

metal, immediately turn OFF dust collector,

disconnect from power, and wait for impeller

to stop. Then empty bag or drum into

approved airtight metal container.

Fire Suppression. Only operate dust collector

in locations that contain fire suppression

system or have fire extinguisher nearby.

Static Electricity. To reduce risk of fire or

explosions caused by sparks from static

electricity, ground all ducting using

grounding wire.

Dust Allergies. Dust from certain woods will

cause an allergic reaction. Make sure you

know what type of wood dust you will be

exposed to in case of an allergic reaction.

Intended Use.

Collecting the wrong materials

can result in serious inhalation hazards, fire,

explosions, or machine damage. This machine

is ONLY designed to collect wood dust and

chips from woodworking machines. DO NOT

use it to collect silica, polyurethane, toxic

fumes, metal dust or shavings, lead paint,

drywall, asbestos, biohazards, explosive dusts,

flammable or combustible liquids or fumes,

nor burning or smoking material.

Wear a Respirator.

Fine dust that is too small to

be caught in filter will be blown into ambient

air. Always wear a NIOSH-approved

respirator during operation and for a short

time after to reduce your risk of permanent

respiratory damage. Never collect dust from

any hazardous material.

Impeller Hazards.

To reduce risk of entanglement

or contact with impeller, DO NOT place hands,

hair, clothing, or tools in or near open dust

collection inlet during operation, and keep

small animals and children away. The powerful

suction could easily pull them into impeller.

Hazardous Dust

. Dust exposure created while

using machinery may cause cancer, birth

defects, or long-term respiratory damage.

Be aware of dust hazards associated with

each workpiece material, and always wear a

NIOSH-approved respirator.

Emptying Dust.

When emptying bag or drum,

wear respirator and safety glasses. Empty

dust away from ignition sources and into

approved container.

Operating Location.

To reduce respiratory

exposure to fine dust, locate permanently

installed dust collectors away from working

area or in another room. DO NOT place dust

collector where it can be exposed to rain or

moisture, which creates a shock hazard and

will reduce life of machine.

Long-term respiratory damage can occur from using dust collectors without proper use of a

respirator. Fire or explosions can result in smoke inhalation, serious burns, or death—if machine

is used to collect incorrect materials, is operated near potential explosion sources, or ducting is

improperly grounded. Entanglement, amputation, or death can occur if hair, clothing, or ﬁ ngers

are pulled into the inlet. To reduce the risk of these hazards, operator and bystanders MUST

completely heed the hazards and warnings below.

PREPARATION

-10-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 PREPARATION

Preparation Overview Required for Setup

The items listed below are required to

successfully set up and prepare this machine for

operation.

For Power Connection

• A power source that meets the minimum

circuit requirements for this machine. (Refer

to the Power Supply Requirements

section for details.)

• A qualified electrician to ensure a safe and

code-compliant connection to the power

source.

For Assembly

• An Assistant

• Safety Glasses (for each person)

• Phillips Screwdriver #2

• Wrench or Socket 1⁄2"

The purpose of the preparation section is to help

you prepare your machine for operation. The list

below outlines the basic process. Specific steps

for each of these points will be covered in detail

later in this section.

The typical preparation process is as follows:

1. Unpack the machine and inventory the

contents of the box/crate.

2. Clean the machine and its components.

3. Identify an acceptable location for the

machine and move it to that location.

4. Assemble the loose components and make

any necessary adjustments or inspections to

ensure the machine is ready for operation.

5. Connect the machine to the power source.

6. Test run the machine to make sure it

functions properly and is ready for operation.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine with

respect and caution to decrease the risk of

operator injury. If normal safety precautions are

overlooked or ignored, serious personal injury

may occur.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your indi-

vidual working conditions. Use this and other

machinery with caution and respect. Failure to

do so may result in serious personal injury or

property damage.

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-11-

PREPARATION

Power Supply

Requirements

Electrocution or fire may

occur if machine is not

correctly grounded and

attached to the power

supply. Use a qualified

electrician to ensure a safe

power connection.

Before installing the machine, consider the

availability and proximity of the required power

supply circuit. If an existing circuit does not meet

the requirements for this machine, a new circuit

must be installed.

To minimize the risk of electrocution, fire,

or equipment damage, installation work and

electrical wiring must be done by a

n electrician

or qualified service personnel

in accordance with

applicable electrical codes and safety standards.

Availability

The full-load current rating is the amperage

a machine draws at 100% of the rated output

power. On machines with multiple motors, this is

the amperage drawn by the largest motor or sum

of all motors and electrical devices that might

operate at one time during normal operations.

The full-load current is not the maximum

amount of amps that the machine will draw. If

the machine is overloaded, it will draw additional

amps beyond the full-load rating.

If the machine is overloaded for a sufficient

length of time, damage, overheating, or fire may

result—especially if connected to an undersized

circuit. To reduce the risk of these hazards,

avoid overloading the machine during operation

and make sure it is connected to a power supply

circuit that meets the requirements in the

following section.

Full-Load Current Rating

Circuit Information

Grounding Requirements

SB1100 at 220V ....................................... 9 Amps

SB1101 at 240V ..................................... 12 Amps

For your own safety and protection of property,

consult an electrician if you are unsure about

wiring practices or applicable electrical codes.

Note: The circuit requirements in this manual

are for

a dedicated circuit—where only one

machine will be running at a time. If this

machine will be connected to a shared circuit

where multiple machines will be running at

the same time, consult a qualified electrician to

ensure the circuit is properly sized.

A power supply circuit includes all electrical

equipment between the main breaker box or fuse

panel in your building and the incoming power

connections inside the machine. This circuit

must be safely sized to handle the full-load

current that may be drawn from the machine for

an extended period of time. (If this machine is

connected to a circuit protected by fuses, use a

time delay fuse marked D.)

This machine must be grounded! In the event

of

certain types of malfunctions or breakdowns,

grounding provides a path of least resistance

for electric current

in order to reduce the risk of

electric shock.

Improper connection of the equipment-grounding

wire can result in a risk of electric shock. The

wire with green insulation (with or without

yellow stripes) is the equipment-grounding wire.

If repair or replacement of the power cord or

plug is necessary, do not connect the equipment-

grounding wire to a live (current carrying)

terminal.

Check with an electrician or qualiﬁed service

personnel if you do not understand these

grounding requirements, or if you are in doubt

about whether the tool is properly grounded.

If you ever notice that a cord or plug is

damaged or worn, disconnect it from power, and

immediately replace it with a new one.

-12-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 PREPARATION

This machine is equipped with a power cord

that has

an equipment-grounding wire and a

grounding plug

(similar to the figure below).

The plug

must only be inserted into a matching

receptacle (outlet)

that is properly installed and

grounded in accordance with all local codes and

ordinances.

This machine is equipped with a power cord

that has

an equipment-grounding wire and a

grounding plug

(similar to the figure below).

The plug

must only be inserted into a matching

receptacle (outlet)

that is properly installed and

grounded in accordance with all local codes and

ordinances.

Grounding Prong

Current Carrying Prongs

6-15 PLUG

GROUNDED

6-15 RECEPTACLE

Figure Figure 3. NEMA 6-15 plug and receptacle.. NEMA 6-15 plug and receptacle.

Extension Cords

SB1100 .............................. 14 AWG, 50 ft or less

SB1101 .............................. 12 AWG, 50 ft or less

We do not recommend using an extension cord

with this machine. If you must use one, only

use it if absolutely necessary and only on a

temporary basis.

Extension cords cause voltage drop, which may

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine

must contain a ground wire, match the required

plug and receptacle listed in the

Circuit

Requirements

for the applicable voltage, and

meet the following requirements:

This machine is prewired to operate on a power

supply circuit that has a verified ground and

meets the following requirements:

Nominal Voltage ......................................... 240V

Cycle .............................................................60 Hz

Phase ..............................................Single-Phase

Circuit Rating....................................... 20 Amps

Plug/Receptacle (included) ...........NEMA 6-20

No adapter should be used with plug. If

plug does not fit available receptacle, or if

machine must be reconnected for use on a

different type of circuit, reconnection must

be performed by an electrician or qualified

service personnel, and it must comply with all

local codes and ordinances.

SB1100 Circuit Information SB1101 Circuit Information

This machine is prewired to operate on a power

supply circuit that has a verified ground and

meets the following requirements:

Nominal Voltage ......................................... 220V

Cycle .............................................................60 Hz

Phase ..............................................Single-Phase

Circuit Rating....................................... 15 Amps

Plug/Receptacle (included) ...........NEMA 6-15

Grounding Prong

Current Carrying Prongs

6-20 PLUG

GROUNDED

6-20 RECEPTACLE

Figure Figure 4. NEMA 6-20 plug and receptacle.. NEMA 6-20 plug and receptacle.

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-13-

PREPARATION

Unpacking

This item was carefully packaged to prevent

damage during transport. If you discover any

damage, please immediately call Customer

Service at

(360) 734-1540 for advice. You may

need to file a freight claim, so save the containers

and all packing materials for possible inspection

by the carrier or its agent.

SB1100 Inventory

Main Inventory (Figure 5) Qty

A. Motor/Impeller Assembly .............................. 1

B. Outlet Tube ....................................................1

C. Collector ..........................................................1

D. Switch Box ...................................................... 1

E. Base ................................................................1

F. Gauge Bracket ................................................1

G. Pressure Gauge ..............................................1

H. Hose

1⁄2" ........................................................... 1

I. Collection Bag ................................................1

J. Square Gaskets ..............................................2

K. Bag Clamp ...................................................... 1

L. Canister Support ............................................1

M. Swivel Casters ................................................4

N. Inlet Adapter .................................................. 1

O. Upper Alignment Arm ...................................1

P. Filter Motor Hardware Bag ...........................1

— Cap Screws M4-.7 x 60 .............................. 4

— Lock Washers 4mm ...................................4

— Flat Washers 4mm ....................................4

— Hex Nuts M4-.7 .........................................4

Q. Hose Clamps 3⁄4" .............................................2

R. Filter Cover ....................................................1

S. Lower Alignment Arm ................................... 1

T. Filter Brush Motor ......................................... 1

U. Gear Reducer .................................................. 1

V. Hex Bolts M6-1 x 16 .......................................2

W. Hex Nuts 10-24 ..............................................2

X. Phillips Head Screws 10-24 x 3⁄4" ................... 2

Y. Flange Nuts 1⁄4"-20 ......................................... 2

Z. Button Head Cap Screws 1⁄4"-20 x 1⁄2" ............ 2

AA. Flange Bolts 1⁄4"-20 x 3⁄4" .................................6

AB. Flange Bolts 5⁄16"-18 x 1⁄2" ............................. 38

AC. Flange Bolts 5⁄16"-18 x 3⁄4" ...............................2

AD. Flange Screw 10-24 x 3⁄8" ...............................1

Figure Figure 5. SB1100 main inventory.. SB1100 main inventory.

JJ

KK

VV

GG

WWXXYYZZAAAA ABAB ACAC ADAD

FF

AA

II

HH

BBCC

DDEE

LLMM

NN

OOPP

QQRR

SS

TT

UU

Figure Figure 6. SB1100 canister filter inventory.. SB1100 canister filter inventory.

AEAE AFAF

AGAG AHAH

Filter Box (Figure 6) Qty

AE. Canister Filter Assembly ............................... 1

AF. Canister Clamp ..............................................1

AG. Foam Tape 5 x 42mm ....................................1

AH. Foam Tape 5 x 20mm ....................................1

-14-

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 PREPARATION

SB1101 Inventory

Main Inventory (Figure 7) Qty

A. Motor/Impeller Assembly .............................. 1

B. Outlet Tube ....................................................1

C. Right Collector ............................................... 1

D. Switch Box ...................................................... 1

E. Base ................................................................1

F. Left Collector ..................................................1

G. Gauge Bracket ................................................ 1

H. Pressure Gauge .............................................. 1

I. Square Gaskets ..............................................3

J. Hose

1⁄2" ........................................................... 1

K. Swivel Casters ................................................ 4

L. Inlet Adapter .................................................. 1

M. Collection Bags ...............................................2

N. Canister Supports .......................................... 2

O. Bag Clamps ....................................................2

P. Filter Motor Hardware Bags ......................... 2

— Cap Screws M4-.7 x 60 .............................. 8

— Lock Washers 4mm ...................................8

— Flat Washers 4mm ....................................8

— Hex Nuts M4-.7 .........................................8

Q. Hose Clamps 3⁄4" .............................................2

R. Filter Covers ...................................................2

S. Upper Alignment Arms ................................. 2

T. Filter Brush Motors ....................................... 2

U. Lower Alignment Arms ................................. 2

V. Gear Reducers ................................................2

W. Hex Bolts M6-1 x 16 .......................................4

X. Hex Nuts 10-24 .............................................. 2

Y. Phillips Head Screws 10-24 x 3⁄4" ................... 2

Z. Flange Nuts 1⁄4"-20 ......................................... 2

AA. Button Head Cap Screws 1⁄4"-20 x 1⁄2" ............ 2

AB. Flange Bolts 1⁄4"-20 x 3⁄4" ............................... 12

AC. Flange Bolts 5⁄16"-18 x 1⁄2" .............................48

AD. Flange Bolts 5⁄16"-18 x 3⁄4" ...............................4

AE. Flange Screw 10-24 x 3⁄8" ...............................1

Filter Box 1 (Figure 8) Qty

AF. Canister Filter Assembly ...............................1

AG. Canister Clamp ..............................................1

AH. Foam Tape 5 x 42mm ....................................1

AI. Foam Tape 5 x 20mm ....................................1

Filter Box 2 (Figure 8) Qty

AF. Canister Filter Assembly ...............................1

AG. Canister Clamp ..............................................1

AH. Foam Tape 5 x 42mm ....................................1

AI. Foam Tape 5 x 20mm ....................................1

Figure Figure 7. SB1101 main inventory.. SB1101 main inventory.

JJ

QQ

UUVV

WWXXYYZZAAAA ABAB ACAC ADAD AEAE

AFAF

AGAG

AHAH AIAI

KK

AA

II

HH

GG

FF

BBCC

DDEE

LL

MM

NN

OOPP

Figure Figure 8. SB1101 canister filter inventory.. SB1101 canister filter inventory.

RR

SSTT

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-15-

PREPARATION

Hardware Recognition Chart

USE THIS CHART TO MATCH UP

HARDWARE DURING THE INVENTORY

AND ASSEMBLY PROCESS.

Hex

Wrench Phillips

Head

Screw

Flat

Head

Screw

Lock

Nut

Wing

Nut

WASHERS ARE MEASURE BY THE INSIDE DIAMETER

LINES ARE 1MM APART

LINES ARE 1/16 INCH APART

3

2 1/4"

2 1/2"

2 3/4"

2

1 3/4"

1 1/2"

1 1/4"

1

9/16"

7/16"

5/16"

3/4"

7/8"

5/8"

1/2"

3/8"

1/4"

7/16"

1/2"

3/8"

1/4"

5/16"

#10

Cap

Screw

Carriage

Bolt Flange

Bolt

Button

Head

Screw

Tap

Screw

External

Retaining

Ring

Internal

Retaining

Ring

E-Clip

Set

Screw

Hex

Nut

Flat Washer

Key

Hex

Bolt

Lock

Washer

5mm

10mm

15mm

20mm

25mm

30mm

35mm

40mm

45mm

50mm

55mm

60mm

65mm

70mm

75mm

MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE

#10

7/16"

1/2"

3/8"

1/4"

5/16"

9/16"

5/8"

Hardware Recognition Chart

5mm

Flat

Head

Cap

Screw

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

4mm

6mm

8mm

10mm

12mm

16mm

4mm

5mm

6mm

8mm

10mm

12mm

-16 -

For Machines Mfd. Since 05/21

South Bend Tools

Model SB1100 & SB1101 PREPARATION

39”

311⁄2"

SB1101SB1100

58"

311⁄2"

Figure 9. Clearances.Figure 9. Clearances.

Physical Environment

Electrical Installation

Lighting

Weight Load

Space Allocation

Weight Load

Refer to the Machine Speciﬁcations for the

weight of your machine. Make sure that the

surface upon which the machine is placed will

bear the weight of the machine, additional

equipment that may be installed on the machine,

and the heaviest workpiece that will be used.

Additionally, consider the weight of the operator

and any dynamic loading that may occur when

operating the machine.

Space Allocation

Consider the largest size of workpiece that will

be processed through this machine and provide

enough space around the machine for adequate

operator material handling or the installation

of auxiliary equipment. With permanent

installations, leave enough space around

the machine to open or remove doors/covers

as required by the maintenance and service

described in this manual.

Physical Environment

The physical environment where your machine

is operated is important for safe operation and

longevity of

parts. For best results, operate this

machine in a dry environment that is free from

excessive moisture, hazardous

or flammable

chemicals, airborne abrasives, or extreme

conditions. Extreme conditions for this type

of machinery are generally those where the

ambient temperature

is outside the range of 41°–

104°F; the relative humidity

is outside the range

of

20–95% (non-condensing); or the environment

is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power

source. Make sure all power cords are protected

from traffic, material handling, moisture,

chemicals, or other hazards. Make sure to leave

access to a means of disconnecting the power

source or engaging a lockout/tagout device.

Lighting

Lighting around the machine must be adequate

enough to perform operations safely. Shadows,

glare, or strobe effects that may distract or

impede the operator must be eliminated.

Children or untrained

people may be seriously

injured by this machine.

Only install in an access

restricted location.

Location

South Bend Tools

For Machines Mfd. Since 05/21 Model SB1100 & SB1101

-17-

PREPARATION

Assembly

The machine must be fully assembled before it

can be operated. Before beginning the assembly

process, refer to Needed for Setup and gather

all listed items. To ensure the assembly process

goes smoothly, first clean any parts that are

covered or coated in heavy-duty rust preventative

(if applicable).

To assemble dust collector:

1. Attach (4) swivel casters to base with (16)

5⁄16"-18 x 1⁄2" flange bolts (see Figure 10).

2. Align motor/impeller assembly with

mounting holes on base. Attach assembly to

base with (4) 5⁄16"-18 x 1⁄2" flange bolts (see

Figure 11).

3. Place square gasket on impeller outlet rim

(see Figure 12).

4. Attach outlet tube to impeller outlet with (5)

5⁄16"-18 x 1⁄2" flange bolts (see Figures 13 &

14). Do not use three inner mounting holes.

Figure Figure 10. Example of swivel caster attached to base.. Example of swivel caster attached to base.

Figure Figure 12. Square gasket in place on impeller rim. . Square gasket in place on impeller rim.

x16x16

Figure Figure 11. Motor/impeller assembly on base.. Motor/impeller assembly on base.

x4x4 Figure Figure 13. SB1100 outlet tube attached. . SB1100 outlet tube attached.

x5x5

Inner Inner

Mounting HoleMounting Hole

Figure Figure 14. SB1101 outlet tube attached. . SB1101 outlet tube attached.

x5x5 Inner Inner

Mounting HoleMounting Hole

SquareSquare

GasketGasket

Page is loading ...

South bend SB1101 Owner's manual

South bend SB1101 Owner's manual

Related papers

Other documents