Anjielo Smart EN-84253 Outdoor manual Owner's manual

Brand: Anjielo Smart

Model: EN-84253 Outdoor manual

Category: Door intercom systems

Type: Owner's manual

MC-0470-V2.0

OPERATION INSTRUCTION

Video Intercom System

Outdoor Station

Instruction

www.anjielo.com

RF CARD

Overview

(2)

(3)

(4)

1. Yellow(Video)

2. Black(GND)

3. White(Audio)

INDOOR

MONITOR Slave

Slave

INDOOR

MONITOR

INDOOR

MONITOR

INDOOR

MONITOR

3. White(Audio)

4. Red(DC12V~15V)

...

MONITOR1

VIDEO1 VIDEO2 VIDEO3 VIDEO4

GND1

OPEN

GND

COM

GND2 GND3 GND4

GND

DC12V

AUDIO1 AUDIO2 AUDIO3 AUDIO4

VCC1 VCC2 VCC3 VCC4

S6 S5

NONO

MONITOR2 MONITOR3 MONITOR4

Wiring Diagram

Camera

Name Plate

Camera Light Unlock Indicator Light

Speaker

Call Indicator Light

Mic

Call Button

Card Reader

Fingerprint Module

Status Indicator

Light

www.anjielo.com

Function

Administration

Talking

Night mode

When the ambient light is low, in the state of

call/monitor/talk, the camera light is automatically

turned on.

Support IC card with 13.56MHz( Max 200pcs card)

During calling/ monitoring/ talking, the “talk light” is

always on, and the light is oﬀ when the call is over.

In the state of unlocking, “unlocking light” is always

on, and the light is oﬀ after the lock is closed.

The “status indicator” ﬂashes when adding or

removing card modes, and it stays on when

returning to normal mode.

1. Full duplex communication

2. Visual intercom

1. Indoor monitor unlock

2. Card unlock

3. Door button unlock

4. Fingerprint unlock(For the devices with ﬁngerprint

only)

Unlock Mode

Support card

type

Talking status

Unlock status

Operation

status

1. Add master card

When the call panel on standby status, keep press the S5 button and S6

button more than 3s and release then till buzzer rings (Bi Bi), Then the

status indicator light ﬂash slowly that the call panel enter add master card

mode.

First use two cards swipe on the card reader, the buzzer will with Bi Bi

sound after swipe card, one of this 2 cards which swipe ﬁrstly is the add

card master card, another card is delete card master card. (the call panel

only accept 2 pieces cards during add card master card mode, add card

During add master card, keep press call button 3 second, return back add

master card mode and back to standby mode. If keep not do setting also

return back standby mode after 30s.

2. Add user card

Notice: One card only can be added once in the above operation.

On standby mode, do setting for outdoor station back side dial switch,

buzzer with sounds feedback. If click to 1, buzzer feedback “Bi” one time,

means unlock time 2s; If click to 2, buzzer feedback “Bi Bi” two time, means

3. User delet master card delet user card

On standby mode, during 10s punch 3 times delete master card enter

delete card mode ( punch ﬁrst and second feedback BI BI two times

sounds, punch the third time feedback BI BI BI three times sound). At this

moment, if punch card will be delete (when succesful feedback BI BI, if

failed feedback BI BI BI BI), puch again delete master card exit (if no

operation after 1min auto exit). If punch add master card, will be delete all

had been programme card( except master card), at the moment, punch

again delete master card seven times BI BI feedback exit; If punch the

empty card, will be failed and exit delete card mode.

4. Set the lock time by dialing code

When the call panel on standby status, swipe the add card master card 3

times within 10s the indicator light ﬂash slowly, ﬁrst swipe and second swipe

buzzer with “Bi Bi” two sound, third swipe buzzer with “Bi Bi Bi” three sound.

Then start swipe the unregistered card on the card reader, (“Bi Bi” two

sound will company with each time if add card successful. “Bi Bi Bi Bi”

four sound will company if failed to add card) , After add all cards or want

to stop adding card, swipe the add card master card can quit add card

mode, (It will quit the add card mode if no any operating in 30s). Then the

CALL indicator light turn on and machine back to standby status.

Two pcs master card, one is add card master card, one is delete card

master card.

master card and delete card master card should not be the same one,

further cards is invalid after these 2 cards, the master card can not delete,

only support add new master card to replace the original one).

www.anjielo.com

unlock time 6s; If click to 3, buzzer feedback “Bi Bi Bi” three time, means

unlock time 8s; If click to 4, buzzer feedback “Bi Bi Bi Bi” four time, means

unlock time 10s.

The following instructions are only applicable to machines with ﬁngerprint

module and should be used with infrared remote control.

Default administrator password: 999999

The default public unlock password: 123456

Default lock time: 2 second

Default security mode: oﬀ

Supports 496 ﬁngerprints.

Press *+ management password (initial administrator password is 999999)

+ # to enter the setting mode, at which time the status indicator will ﬂash

slowly.

Enter the administrator action state:

Mode

Time

10s

1 2

1. Modify the management password, public door password and

restore factory settings

Controller function introduction (For the devices with controller only)

Admin password: After entering admin mode, press 0 (status indicator

ﬂash) +77 + +NNNNNN (six digit password) + +NNNNNN (enter password

again) +#. After two beeps, the modiﬁcation succeeds and returns to the

setting mode.

Public opening password: After entering administrator mode, press 0

(status indicator ﬂash) +11 +#+NNNNNN (4-6 password) +#+NNNNNN

(enter password again) +#.

Restore factory setting:

After entering administrator mode, follow these steps to add the card.

After entering administrator mode, follow these steps to delete the speciﬁed

number card and password.

1 + NNN + # + swipe

Notice:

Steps:

Deletes the speciﬁed number card

A. Only one card can be added per bit number. Adding diﬀerent cards

with the same bit number will cause the previously added cards to

be replaced. Remember to add the bit number when you add the card,

so that the previous card will not be invalidated due to repeated additions.

B. The newly added card will automatically generate a default password

of “0000”. This password cannot be used to open the door and will

only be used for user to change the password.

(1). Enter 1 in administrator mode to enter add card mode (status indicator

ﬂash).

(2). Enter the three-digit NNN (digit 000~199) and press # to conﬁrm.

(3). When you swipe your card in the swipe sensing area, BIBI will sound

twice to indicate that the card has been added successfully.BI, BI,

BI, BI, four sound, it fails to add the card, indicating that the card has

been added.

(4). Repeat steps 2 through 3 to add ﬁngerprints continuously.

2. Add door opening cards

3. Delete door opening card

(1). After entering the administrator mode, press 0(status indicator ﬂash)

+99 + # (Bi -- sound, status indicator stops ﬂashing), and the machine

will resume factory Settings.

(2). In standby mode, press and hold the left and right buttons on the back

of the machine to power up. When the buzzer drops 3, it means the

factory has successfully resumed.

Steps:

2 + NNN + #

(1). Enter 2 in administrator mode to enter delete card mode (status

www.anjielo.com

After entering the administrator mode, press 4 (status indicator ﬂash)+ 00

-99(indicating opening time)+# (BI BI two sound, status indicator slow ﬂash)

to set successfully. If set to 02, the opening time will be 2 seconds, and so

on. But if set to 00, the induction card swiping once is on and then swiping

again is oﬀ.

Swipe card open the door

Card or password to open the door

Steps:

6. User Operation

Read card deletion

5. Safe mode

Delete all cards

2 + Read card

2 + 88 + #

Press 5 (status indicator ﬂash) +00+# (BI BI twice, status indicator ﬂash

slowly) -- oﬀ mode.

Press 5 (status indicator ﬂash) +01+# (BI BI two sound, status indicator

ﬂash slowly) -- lock mode: within 5 minutes, the machine will look for 2

minutes if you continuously brush invalid card or enter the wrong password

for 10 times, the status indicator will ﬂash and automatically call the indoor

machine. Keystrokes and card swiping are invalid during this period.

(Except call buttons)

Press 5 (status indicator ﬂash) +02+# (BI BI two sound, status indicator

ﬂash slowly) -- alarm mode: indicating that within 5 minutes, the machine

will lock up and alarm for 1 minute if you continuously brush invalid card

or enter the wrong password. Meanwhile, the status indicator will ﬂash

and automatically call the indoor machine. Keystrokes and card swiping

are invalid during this period. (Except call buttons)

After entering administrator mode, follow these steps to switch to safe

mode.

(1). Enter 9 in administrator mode to enter delete card mode (status indicator

ﬂash).

(1). Enter 2 in administrator mode to enter delete card mode (status indicator

ﬂash).

Note: During any of the above Settings, press * to exit or return to the

previous level.

After entering administrator mode, follow these steps to delete the read

card.

After entering administrator mode, follow these steps to delete all cards.

(2). Swipe your card in the swipe sensing area and BIBI will sound twice

to indicate successful deletion (status indicator ﬂashes quickly).

(2). Enter 88 and press # to conﬁrm.

Swipe a valid card in the induction zone or enter the password +# on the

Brush the added valid card in the induction zone, open the door.

The user USES the card to change the password.

In standby state, press *, read card + old password +# (default 0000, BI

BI twice, status indicator light ﬂashes slowly), NNNN (four-digit new

password) +#+NNNN (enter password again) +#. If the operation is correct,

the status indicator will stop ﬂashing once BI, indicating the password has

been modiﬁed successfully.

(3). Repeat step 2 to continuously delete the read card and password.

Repeat step 2 to continuously delete the read card and password.

(3). Equipment Bi...Delete all card successfully after multiple sounds,

return to administrator mode (status indicator ﬂashes slowly).

(3). After BIBI rings twice, the card and password with speciﬁed number

are deleted successfully (status indicator ﬂashes quickly).

(4). Repeat step 2 to continuously delete the numbered card and password.

4. Set the lock time by infrared remote control

(2). Enter the three-digit NNN (digit 000~199) and press # to conﬁrm.

indicator ﬂash). Note: Both dial code and infrared remote control are supported to set the

unlocking time. The unlocking time is subject to the last setting.

www.anjielo.com

Steps:

Delete all ﬁngerprints

Read ﬁngerprint delete

9 + Fingerprint reading

9 + 88 + #

Step:

Card + password open the door

7. Add ﬁngerprints

(2). Enter the three-digit NNN (digit 000~495) and press # to conﬁrm.

(3). The ﬁngerprint of the speciﬁed number was successfully deleted after

BIBI sounded twice (status indicator ﬂash).

(4). Repeat step 2 to continuously delete a ﬁngerprint with a speciﬁed

number.

(1). Enter 8 in administrator mode to add ﬁngerprint mode (status indicator

ﬂash).

Note: only one ﬁngerprint can be added per bit. Adding diﬀerent ﬁngerprints

to the same bit will cause the previously added ﬁngerprint to be

replaced.

When adding a ﬁngerprint, remember to add the bit number so that

the previous ﬁngerprint will not be invalidated due to repeated

additions.

After entering administrator mode, follow these steps to remove the read

ﬁngerprint.

(1). Enter 9 in administrator mode to delete ﬁngerprint mode (status indicator

ﬂash).

(1). Enter 9 in Administrator mode to delete ﬁngerprint mode (status indicator

ﬂash).

(3). Repeat step 2 to continuously delete the read ﬁngerprint.

(2). Hold your ﬁnger in the read-write area. The read-write area will turn

green and BIBI will sound twice to indicate the successful deletion

(status indicator will ﬂash).

(2). Enter 88 and press # to conﬁrm.

(3). Equipment Bi...Delete all prints successfully after multiple sounds.

Return to administrator mode (status indicator light ﬂashes slowly).

After entering administrator mode, follow these steps to add a ﬁngerprint.

8 + NNN + # + ﬁrst registration ﬁngerprint + second registration ﬁngerprint.

(2). Enter the three-digit NNN (digit 000~495) and press # to conﬁrm.

(4). Continue to register with the same ﬁnger close to the read-write area

for a second time. When BIBI is heard twice again, the registration is

successful.

(5). The same ﬁngerprint can be registered twice to complete the speciﬁed

number of ﬁngerprints added.

(6). Repeat steps 2 through 4 to add ﬁngerprints continuously.

(1). Enter 9 in administrator mode to delete ﬁngerprint mode (status indicator

ﬂash).

After entering administrator mode, follow these steps to remove the speciﬁed

number ﬁngerprint.

After entering administrator mode, follow these steps to remove all ﬁngerprints.

(3). Hold your ﬁnger in the read-write area and BIBI will indicate the ﬁrst

successful registration.

After swiping a valid card, enter the password +#, and open the door when

both are correct.

8. Delete the ﬁngerprint

Removes the speciﬁed number ﬁngerprint

Step:

9 + NNN + #

910

keyboard, one of which is correct to open the door.

www.anjielo.com

Camera

Flush Mount

Surface Mount

1/4, 1/3in CCD/CMOS

sensing distance ≤3cm

Environment temperature o o

-30 C～+50 C

Power supplier DC：+12V—+15V

Power consumption 150mA max.

LED night White camera light

Deﬁnition 800 TVL

viewing angle 90° 90° 90° 110°

Installation Embedded installation/ Surface

installation

Product parameter

RF CARD

720P 960P 1080P

11 12

www.anjielo.com

110

Installation Process of Door Station

Outdoor unit ---------------------------------------------------------------

Plastic Anchors -----------------------------------------------------------

Screws ------------------------------------------------------------------------

5 pin line---------------------------------------------------------------------

User manual --------------------------------------------------------------

4 pin line---------------------------------------------------------------------

Power adapter ------------------------------------------------------------

2 pin line --------------------------------------------------------------------

1PCS

4PCS

1PCS

4PCS

1PCS

Accessories

RF CARD

13 14

Avoid installation of the device near strong radiation e.g. AC motor

and lift.

Maintenance should be complied with qualiﬁed technician.

Keep it away from the water and magnetic ﬁeld.

Keep more than 30cm away from AC power supply to avoid external

interference.

Switch oﬀ power supply before installation.

Select the most suitable position where the camera is located at user’s

eye level.

Avoid hard shake, beating and collision, otherwise the internal exact

components maybe be damaged.

Do not expose the outdoor camera under strong light or sunshine.

Do not install the outdoor camera in the environment e.g. direct sunlight,

contact rain, high temperature, high humidity, full of dust and chemistry

corrosive.

www.anjielo.com

Anjielo Smart EN-84253 Outdoor manual Owner's manual

Brand: Anjielo Smart

Model: EN-84253 Outdoor manual

Category: Door intercom systems

Type: Owner's manual

Download PDF

report

Anjielo Smart EN-84253 Outdoor manual Owner's manual

Anjielo Smart EN-84253 Outdoor manual Owner's manual

Related papers

Other documents