ELAMOR Keyless Entry Door Lock Deadbolt Installation guide

Brand: ELAMOR

Model: Keyless Entry Door Lock Deadbolt

Type: Installation guide

OPERATION MANUAL

KEYLESS DEADBOLT LOCK

5757

545454

Battery Cover

Reset Button

Back Knob

Unlock Status

Lock Status

1.Details

Keypad

Cylinder

Unlock Button

Conﬁrm Button

“ # ” Button

Lock Button

Return Button

*“ ” Button

Fingerprint

Reader

5757

545454

5.Set up

After the installation is completed, it is necessary to correct the locking direction of the door lock

through the “Self-test Function” of the device:

1. Keep the door open, twist the back knob manually to extend the lock bolt and keep it extended.

2. Press the key “ ”+“ ”+“ 9 ”+“ ” , and the device will automatically adjust the locking direction.

3. After the adjustment is completed, the lock bolt will automatically retract and become the

unlocked state, otherwise perform the above operation again.

4. If the device enters the user, it needs to verify the master code or ﬁngerprint before performing the

“Self-test Function” .

Note:

1. The master code is “ 123456 ” under factory default conditions. After adding master, the default

code becomes invalid.

2. If there is no master, the default code has administrator privileges.

3. Users can set a 6-8-digit code.

4. Users can prevent the code from being exposed to strangers by entering random numbers before

and after the code, and the number of digits does not exceed 40.

5. The “ ” key has function of locking and returning , and the “ ” key has the function of unlocking

and conﬁrming. Users can also unlock and lock by verifying ﬁngerprint.

6. If you enter the wrong code or ﬁngerprint 5 times in a row, the system will be locked for 3 minutes.

This state can be released after the time is up or the power is cut oﬀ.

Instructions(press “ ” or timeout to exit)

Add master code or ﬁngerprint:

1. Press “ ”+“ ”+“ 1 ”+“ ” .

(Need to enter a master code before enter ﬁngerprints)

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. Enter the master code + “ ” twice in a row or enter ﬁngerprint 5 times.

4.10 master codes or ﬁngerprint can be added, and the location number range is 001-010.

5. The location number of the ﬁrst master code or ﬁngerprint added is 001 and so on.

Add user code or ﬁngerprint:

1. Press “ ”+“ ”+“ 2 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. Enter the user code + “ ” twice in a row or enter ﬁngerprint 5 times.

4. 40 user codes or ﬁngerprint can be added, and the location number range is 011-040.

5. The location number of the ﬁrst user code or ﬁngerprint added is 011 and so on.

Add a one-time code:

1. Press “ ”+“ ”+“ 3 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. Enter the one-time code + “ ” twice in a row.

4. The one-time code can only open the lock once, and the code will be automatically invalidated and

deleted after use.

5. 10 one-time codes can be added.

Delete user code (There are three ways):

1. Press “ ”+“ ”+“ 4 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. Enter the unneeded code or ﬁngerprint + “ ” .

4. Enter the location number of the unneeded code or ﬁngerprint + “ ” .

(For example, 002 represents the second master code, 012 represents the second user code)

5. Enter "0000" + “ ” to delete all user codes or ﬁngerprint except the master code or ﬁngerprint.

6. Master code or ﬁngerprint need to be kept at least one.

7. The newly added code and ﬁngerprint will be ﬁlled to the front position.

5757

545454

Vacation mode:

1. Press “ ”+“ ”+“ 5 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. When vacation mode is enabled, no user code or ﬁngerprint other than the master will be able to

open the door until the mode is disabled.

Silent mode:

1. Press “ ”+“ ”+“ 6 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. Enable and disable silent mode.

Delayed auto-lock function:

1. Press “ ”+“ ”+“ 8 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. Enter the delay auto-lock time + “ ” .

4. The time can be set for 5-30 seconds / input "0" + " " to disable the delay automatic locking

function.

Self-test Function:

1. Keep the door open, twist the back knob manually to extend the lock tongue and keep it extended.

2. Press the “ ”+“ ”+“ 9 ”+“ ” , and the device will automatically adjust the opening direction.

3. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

4. After the adjustment is completed, the lock tongue will automatically retract and become the

unlocked state, otherwise perform the above operation again.

5. When the device cannot be used normally, it can be adjusted to the normal state through the

“Self-test Function” .

Restore to factory default settings:

Method 1:

1. Press and hold the reset button 5 seconds through the “ Reset-PIN ” until a long beep is heard.

2. Release the reset button.

3. The factory default settings are restored successfully.

Method 2:

1. Press “ ”+“ ”+“ 0 ”+“ ” .

2. Verify the master code + “ ” conﬁrm or verify the master ﬁngerprint.

3. The factory default settings are restored successfully.

5757

545454

6.Functions

Add master code: + + 1 +

Restore to factory default settings

123456

Default Settings

Add user code: + + 2 +

Add a one-time code: + + 3 +

Self-test Function: + + 9 +

10 master codes or ﬁngerprint can be added, and the location number range is 001-010.

The location number of the ﬁrst master code or ﬁngerprint added is 001 and so on.

40 user codes or ﬁngerprint can be added, and the location number range is 011-040.

The location number of the ﬁrst user code or ﬁngerprint added is 011 and so on.

The one-time code can only open the lock once

10 one-time codes can be added.

No user code or ﬁngerprint other than the master will be able to open the door until

the mode is disabled

Press and hold the reset button 5 seconds through the “ Reset-PIN ”.

Press “ ”+“ ”+“ 0 ”+“ ” + Verify the master code or ﬁngerprint + “ ” conﬁrm.

Enter the unneeded code or ﬁngerprint + “ ” conﬁrm.

Enter the location number of the unneeded code or ﬁngerprint + “ ” conﬁrm.

Enter "0000" + “ ” key to delete all user codes or ﬁngerprint except the master.

After the installation is completed, it is necessary to correct the locking

direction of the door lock through the “Self-test Function” of the device.

When the device cannot be used normally, it can be adjusted to the normal

state through the “Self-test Function”

Vacation mode : + + 5 +

Oﬀ

Delete user code: + + 4 +

Above

Default Settings

Delayed auto-lock: + + + 8

Enter the delay auto-lock time + “ ” conﬁrm.

The time can be set for 5-30 seconds

input "0" + " " key to disable the delay automatic locking function

Oﬀ

Default Settings

Silent mode: + + + 6

Enable and disable silent mode.

Oﬀ

Empty

575757

5454

ELAMOR Keyless Entry Door Lock Deadbolt Installation guide

Brand: ELAMOR

Model: Keyless Entry Door Lock Deadbolt

Type: Installation guide

Download PDF

report

ELAMOR Keyless Entry Door Lock Deadbolt Installation guide

ELAMOR Keyless Entry Door Lock Deadbolt Installation guide

Other documents