Infinova V1492N-28N05 Operating instructions

Brand: Infinova

Model: V1492N-28N05

Category: Security cameras

Type: Operating instructions

This manual is also suitable for



V1492N-N Series

High-speed IP PTZ Camera System

Operation Manual









This manual mainly addresses the operation and programming of Infinova V1492N-N series high-speed IP

PTZ cameras. Based on network technology, V1492N-N series integrated high-speed IP PTZ cameras could

easily realize network digital video transmission and network control function, and provide professional

remote video services. They provide high-reliable, cost-effective solutions to various applications.



Notice

This manual may not be reproduced in any form or by any means to create any derivative such as translation, transformation, or adaptation

without the prior written permission of Infinova.

Infinova reserves the right to change this manual and the specifications without prior notice. The most recent product specifications and

user documentation for all Infinova products are available on our web site www.infinova.com..

Trademarks

Infinova

® is a trademark of Infinova.

All other trademarks that may appear belong to their respective proprietors.

FCC Warning

The V1492N-N series high-speed IP PTZ cameras comply with the FCC rules.

Operation is subject to the following two conditions:

zThis device will not cause harmful interference.

zThis device must accept any interference received, including interference that may cause undesired operations.

The V1492N-N series high-speed IP PTZ cameras have been tested and found to comply with the limits for a Class A digital device,

pursuant to the FCC rules. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not

occur in a particular installation.



Read this manual carefully before installation. This manual should be saved for future use.

Important Safety Instructions and Warnings:

zElectronic devices must be kept away from water, fire or high magnetic radiation.

zClean with a dry cloth.

zProvide adequate ventilation.

zUnplug the power supply when the device is not to be used for an extended period of time.

zOnly use components and parts recommended by manufacturer.

zPosition power source and related wires to assure to be kept away from ground and entrance.

zRefer to qualified personnel for all service matters.

zSave product packaging to ensure availability of proper shipping containers for future transportation.

Indicates that the un-insulated components within the product may carry a voltage harmful to humans.

Indicates operations that should be conducted in strict compliance with instructions and guidelines contained in this manual.



Warning: To avoid risk of fire and electric shock, keep the product away from rain and moisture!



Table of Contents



&KDSWHU,6\VWHP,QWURGXFWLRQ 

1.1 Product Description .................................................................1

1.2 Product Features ......................................................................1

1.3 Product Model..........................................................................2

1.4 Product Specifications .............................................................2

1.5 Notice.......................................................................................3

&KDSWHU,,,QVWDOODWLRQ 

2.1 Dimensions ..............................................................................3

2.2 Desktop Mount ........................................................................4

2.3 Wall Mount ..............................................................................4

2.4 Pole Mount...............................................................................4

2.5 Corner Mount........................................................................... 5

&KDSWHU,,,,(%URZVHU6HWWLQJ 

3.1 Software Installation ................................................................5

3.2 Set IE Browser ......................................................................... 6

&KDSWHU,9%DVLF)XQFWLRQ2SHUDWLRQ 

4.1 Login........................................................................................ 7

4.2 System Information.................................................................. 8

4.3 Account Settings ......................................................................8

4.4 Network Settings......................................................................9

4.4.1 MAC address.................................................................... 9

4.4.2 IPv4 setting.......................................................................9

4.4.3 Network Link ................................................................. 10

4.4.4 FTP settings.................................................................... 10

4.4.5 SMTP Settings................................................................10

4.4.6 SNMP Settings ............................................................... 10

4.5 Time Settings ......................................................................... 10

4.6 Alarm settings ........................................................................ 10

4.7 PTZ Settings .......................................................................... 11

4.8 System Log ............................................................................ 11

4.9 Deinterlaced Settings ............................................................. 11

4.10 SD Card ............................................................................... 11

4.11 Recording Control................................................................12

4.12 Security................................................................................ 12

4.13 Advanced Settings................................................................ 12

4.13.1 Software Update...........................................................12

4.13.2 Factory Settings............................................................13

4.13.3 Online Reboot ..............................................................13

&KDSWHU9+9LGHR6HWWLQJV  

5.1 Video Size.............................................................................. 14

5.2 Player..................................................................................... 14

5.3 Stream Type ........................................................................... 14

5.4 Motion Detection ................................................................... 14

5.5 Privacy mask.......................................................................... 15

5.6 Color Setting.......................................................................... 15

5.7 Image Quality ........................................................................ 15

5.8 OSD Settings ......................................................................... 15

5.9 Qos Setting ............................................................................ 16

5.10 Resolution Settings .............................................................. 16

5.11 I/P Rate ................................................................................ 16

5.12 Frame Rate........................................................................... 16

5.13 Bit Rate................................................................................ 17

5.14 Audio ................................................................................... 17

5.15 Snapshot............................................................................... 17

&KDSWHU9,0-3(*9LGHR6HWWLQJ 

6.1 Resolution.............................................................................. 18

6.2 Image Quality ........................................................................ 18

6.3 Frame Rate............................................................................. 18

6.4 Snapshot................................................................................. 18

&KDSWHU



9,,0HQX6HWWLQJV  

&KDSWHU



9,,,



37=&DPHUD&RQWURO 

8.1 Lens Direction Control .......................................................... 20

8.2 Lens Function setting............................................................. 21

8.3 Pan/Tilt Control Function ...................................................... 21

8.3.1 Speed Adjustment .......................................................... 21

8.3.2 Setting Preset and Calling up Preset............................... 21

8.3.3 Setting Pattern and Calling up Pattern............................ 21

8.3.4 Setting Autopan and Calling up Autopan....................... 22

8.3.5 Calling up Autoscan....................................................... 22

8.3.6 Calling up Flip Horizontal 180° ..................................... 22

&KDSWHU9,,,,9LGHR'RZQORDG 

$SSHQGL[,0DJQHWLF5LQJ)LOWHU,QVWUXFWLRQ  

$SSHQGL[,,4XHVWLRQV6ROXWLRQV 

$SSHQGL[,,,',36HWWLQJV 

1. Setting Camera ID ................................................................... 27

2. Setting Communication Baud Rate and Protocol..................... 29

$SSHQGL[,9  &DEOH'LDPH WHU &DOFXODWLRQ DQG/LJKWQLQJ 

6XUJH3URWHFWLRQ  

$SSHQGL[96HWXS5HPRYDORI,QIL5HSOD\HU 

Chapter I System Introduction

1.1 Product Description

This manual addresses the operation and programming procedures

of Infinova V1492N-N series high-speed IP PTZ cameras.

With 10/100M Base-T self-adaptive network functions, the

V1492N-N series can output H.264/M-JPEG format video and

support triple stream encoding and bi-directional audio. Strong

capability of network remote control not only allows the relative

software to search network video, but also sets the IP address,

subnet mask & gateway of the video server via Internet Explorer, as

well as video encoding, e.g., pre-define encoding parameters, data

transmission rate, image quality, etc.

A powder-coated, aluminum construction makes the V1492N-N

ideal for either indoor or outdoor applications. The system has an

absolute operating temperature range of -40°F ~ 140°F (-40°C ~

60°C). The V1492N-N series are available with an input voltage of

24VAC or with a selectable power source of 24VDC.

The V1492N-N series include a window wiper. The wiper is

completely integrated into the enclosure and does not interfere with

the viewing range of the system.

1.2 Product Features

&RPSDULQJWRLWV FRXQWHUSDUWV,QILQRYD¶ V911VHULHV 

KLJKVSHHG, 337= FDPHUDV K DYHWK HIROOR ZLQJIHDWX UHV DQG

IXQFWLRQV

zNetwork Video Commission: view the video via Windows IE

browser.

zSupport multiple users’ simultaneous visit, sending video to

multiple video receivers simultaneously.

zSD card storage

zNetwork Video Commission: transform the analog video to

digital signal and transmit to receiver via network; real-time

monitoring from client computer via Windows IE browser is

supported

zBuilt-in Web Server, accessible for Internet explorer 6.0 and

higher versions.

zNetwork control signal transmission

zPassword protection

zSupport set IP address manually.

zSupport Dynamic I/P Frame Rate

zSupport Dynamic Quality and Compression Rate adjustment

(Via network)

zMotion detection

zSnapshot function

zControllable Digital Focus (Digital Zoom)

zRemote software upgrade

zNetwork Remote Control. Send RS485 control command to

decoder, and thus drive the Pan/Tilt and the three-vari (vari-iris,

vari-focus, vari-zoom) lens or directly control equipments via

RS485 interface (optional).

zAlarm function (optional)

zSupports multiple ways to handle alarms, such as sending an

email, FTP upload, audible alarm, relay output

zEmbedded INFINOVA, PELCO-P and PELCO-D protocols.



$SDUWIURPDERYHIHDWXUHVWKLV,337=FDPHUDSRVVHVVHV

z+LJKUHVROXWLRQ,PDJH&RPSUHVVLRQ

The high-speed IP PTZ cameras support 4CIF, 2CIF, CIF, QCIF

resolution image compression.

z,PSURYHG1HWZRUN)XQFWLRQ

Infinova’s V1492N-N series high-speed IP PTZ cameras support

the entire TCP/IP Protocol Suite (RTP/RTSP, TCP, IP, HTTP, SNMP,

UDP, SMTP etc). The system is allowed to adjust the bit rate and

frame rate of V1492N-N series high-speed IP PTZ cameras network

layer, and optional manual/Auto set QP (I Frame /P Frame)

parameters are provided in order to adapt to the critical application

requirements of surveillance system. Event log, summary

information could be set on the real-time interface, and the

snapshots could also be saved.

z5HGXQGDQW,QWHUIDFHVDQG6ZLWFKFRQWURO)XQFWLRQ

The parameters such as control protocol, baud rate, PTZ speed etc.

could be adjusted through the interfaces on Infinova V1492N-N

series integrated high-speed IP PTZ cameras. Quick & accurate

remote PTZ control makes network surveillance easy. Transparent

RS-485 data ports are provided to communicate with the external

devices. They could be directly accessed to the network through

RJ45 self-adaptive 10M/100M network connector.

z0XOWLSOH[LQJ7HFKQLFDO6XSSRUW

Adopting high-precise driving system, the high-speed IP PTZ

cameras could quickly orient and continuously scan, provide

high-quality, full-Notion, full-color, and real-time active images,

detect the moving objects, and set video encodings. The high-speed

IP PTZ camera could preset encoding parameters and data

transmission rate, etc.

z([WHQVLYH$SSOLFDWLRQ)LHOGV

Based on the encrypted TCP/IP protocol transmission, Infinova’s

V1492N-N series high-speed IP PTZ cameras could be widely used

in the applications requiring professional surveillance, such as

airports, railway stations, jails, warehouses, factories, shores,

campuses, etc.

z)OH[LEOHVHWW LQJVWRWXQHWK HFRORU VDWXUDWLRQDQGLPDJH

EULJKWQHVV

z6HWDODU PSDUDPH WHUVDQGYLGH RSDU DPHWHUVWKU RXJKWKH 

PHQXRQWKHZHESDJH



z&RPSO\ZLWK219,)VSHFLILFDWLRQ

V1492N-N series complies with ONVIF (Open Network Video

Interface Forum) specification, which ensures high compatibility

among various network video products, providing cost-efficient,

flexible and reliable solutions.

1.3 Product Model

7KLVLQVWDOODWLRQPDQXDOVXLWVIRU,QILQRYDSURGXFWV

V1492N-18N05 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

18X, 24 VDC)

V1492N-18N06 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

18X, 24 VAC)

V1492N-18N15 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

18X, 24 VDC)

V1492N-18N16 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

18X, 24 VAC)

V1492N-28N05 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

28X, 24 VDC)

V1492N-28N06 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

28X, 24 VAC)

V1492N-28N15 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

28X, 24 VDC)

V1492N-28N16 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

28X, 24 VAC)

V1492N-35N05 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

35X, 24 VDC)

V1492N-35N06 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

35X, 24 VAC)

V1492N-35N15 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

35X, 24 VDC)

V1492N-35N16 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

35X, 24 VAC)

V1492N-36N05 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

36X, 24 VDC)

V1492N-36N06 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, NTSC,

36X, 24 VAC)

V1492N-36N15 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

36X, 24 VDC)

V1492N-36N16 Integrated High-speed IP PTZ Camera

System (H.264/M-JPEG Format, PAL,

36X, 24 VAC)

3DUW1XPEHU([WHQVLRQVIRU$ODUP$XGLR566HOHFWLRQ

:LWKRXW$ODUP

$XGLR56

:LWK$ODUP

$XGLR56 (; (;:LWK$ODUP

$XGLR56

none W V1492N-18N06 V1492N-18N06W

1.4 Product Specifications

9LGHR

Video Compression: Three Simultaneous Video Streams: Dual

H.264 & Scalable M-JPEG

Maximum Resolution: 4CIF @H.264/M-JPEG

Optional Resolution:

Major stream: NTSC: 4CIF(704×480)/2CIF(704×240)/

CIF(352×240)/QCIF(176×120)

PAL: 4CIF(704×576)/2CIF(704×288)/

CIF(352×288)/QCIF(176×144)

Minor stream: NTSC:CIF(352×240)/QCIF(176×120)

PAL: CIF(352×288)/QCIF(176×144)

Data Rate: 256Kbps ~ 3Mbps

Frame Rate: PAL: 25fps; NTSC: 30fps (max)

*HQHUDO

Video Decoder: PELCO-P/D, INFINOVA

Presets: 254

Pattern: 4

Auto Pan: 4

Auto Scan: 1

Motion detection: Yes

Alarm (optional): 2 alarm inputs, 2 outputs

SD card storage: Available



$XGLRRSWLRQDO 

Compression: G.711

Ports: 1 input/1 output

(OHFWULFDO

Input Voltage: 24VAC/24VDC

Power Consumption: 24VAC: 53W; 24VDC: 51W;

Heater: Thermostatically controlled

0HFKDQLFDO

Pan Movement: 360° Continuous Pan Rotation

Vertical Tilt: Unobstructed +40° to -90°

Variable Pan/Tilt Speed:

Pan: 0.1° to 50°/sec variable-speed operation,

Tilt: 0.1° to 25°/sec variable-speed operation

Preset Speeds:

Pan: 100°/sec

Tilt: 30°/sec

Camera Mounting: Integrated camera sled assembly

Weight: 21 lbs. (9.5 kg)

Load:

Pan: 22 lbs. (10 kg)

Tilt: 7.7 lbs. (3.5 kg)

Construction: Die-cast, extruded and sheet aluminum,

stainless steel hardware

Protection Rating: IP66

Mounting: Desktop Mount, Wall Mount, Pole Side

Mount, Corner Mount, Pole Top Mount

Auto Controlled Temperature:

Heater: Turns on at 50°F ± 9°F (10°C ± 5°C)

Turns off at 86°F ± 9°F (30°C ± 5°C)

(QYLURQPHQWDO

Environmental Air Pressure: 1.5MPa

Temperature: -40°F ~ 140°F (-40°C ~ 60°C)

Humidity: 0~95%RH (non-condensing)

1.5 Notice



1. Firstly perform network settings after login. Gateway IP address

should be set as the gateway connected to the V1492N-N IP PTZ

cameras.

2. The IP address and MAC address should not conflict with the IP

address and MAC address of other devices, or no image will be

available.

3. No need to restart the system after performing network settings.

4. If you do not remember the IP address of the IP PTZ camera,

then you can use the scanning software on the PC to detect the IP

address, and you can also restore the default settings (such as IP

address) via the “One Button Reset” function on the base PCB of

high-speed IP PTZ camera (the Reset button is S100).

Chapter II Installation

2.1 Dimensions

There are 4 ways for the mounting of high-speed PTZ camera:

desktop mount, wall mount, pole mount and corner mount.

(Unit: mm)

37=&DPHUD'LPHQVLRQV

443.4

147.6

167.3

94.5

302.4

315.0

%UDFNHW'LPHQVLRQV

1RWH The PTZ camera’s ID and baud rate can be set via either

software or DIP switch. With the two ways, there are totally 254

address IDs settable for PELCO-P/D and INFINOVA protocols.

For specific setup via DIP switch, please refer to Appendix III

before installation. Address ID = Value of DIP switch + 1 (OFF=0

ON=1).

If the 8 positions on DIP switch S1 are all placed to ON position, it

indicates users can set address ID and baud rate via software. Please

refer to Chapter VII for details.

2.2 Desktop Mount

The desktop mount is chiefly suitable for the places in which there

are various kinds of desk, rooftop, balcony, etc, and according to

the vertical rotation range of PTZ camera from -90eto 40efor the

sake of its mechanism structure, the PTZ camera has to be mounted

at the edge of desktop. Thus, something related to the intensity and

other factors of the desktop has to be taken into consideration. In

the process of mounting, there has to be a few holes to be drilled in

a proper distance from the edge of desktop, and then fix the PTZ

camera adapter there by using expansion bolts. Confirm whether it

is firm enough, then mount the PTZ camera and finish the whole

mounting. Users can select the suitable way how the cable is pulled

out according to their need. Below figures demonstrate the way

how the cable is dragged out.

Desktop Mount Structure

Cable dragged out from the side

(Mainly used when there is not enough room below the desktop)

Cable dragged out from the base

(Mainly used when there is enough room below the desktop)

2.3 Wall Mount

Wall mount is to fix the PTZ camera on the erect or slanting plane

by means of some specific auxiliary mounting components, and

before mounting, these wall mount brackets have to be fixed on

wall or other erect planes. After it is fastened steadily, just mount

the PTZ camera on the bracket to complete the mounting. Shown as

below:

Wall Mount Bracket Structure

Cable hole, as referenced

size, actual size depends on

construction needs.

M8 or same type

eyelet bolts (British

measurement )

Cable dragged out from the side

Wall Mount Bracket Structure

Cable hole,

Ø40.0 as referenced

size,actual size depends on

construction needs.

M8 or same type

eyelet bolts (British

measuremen t )

Ø40.0

108.0

127.0

4-Ø8.0

Cable dragged out from the base

2.4 Pole Mount

Pole side mount is to install the PTZ camera to the cylinder via

linkage components. It is necessary to fix a connection board to the

cylinder via a hoop before installing. Then, install the wall mount

brackets to the connection board. After it is fastened steadily, just

mount the PTZ camera on the wall bracket to complete the

mounting.

Cable from the side

Cable dragged out from the base

2.5 Corner Mount

Corner mount is to install the PTZ camera to the suitable position of

the corner via linkage component. It is necessary to fix the Corner

Mount Adapter to the corner before installing. Then, install the corner

mount brackets to the Corner Mount Adapter. After it is fastened

steadily, just mount the PTZ camera on the wall bracket to complete

the mounting. Shown as below:

Wall II Wall I

Corner Mount Adapter Structure

M6 Expanded Bolts

M6 Expanded

Bolts

Corner Line

Cable dragged out from the side

150.0

Cable dragged out from the base

1RWH all the brackets for all the above mount ways sold separately.

Chapter III IE Browser Setting

zSupport IE browser version: Internet Explorer 6.0 or greater;

zBefore attempting to view the image, make sure the system have

Directx 9.0c or greater image viewer software.

zInstall Quicktime.



3.1 Software Installation

(TXLSPHQW&RQQHFWLRQ

zConnection order: Firstly connect the network cables; then

connect the video (only used for servers)

zNote: Check if the connection is tight or not before power-on.

After turning on the power, the system will carry out self-checking

which takes about 30 seconds.

,QVWDOODWLRQ3URFHGXUHV

The installation procedures of V1492N-N Integrated High-speed IP

PTZ Camera Image software are listed as follows:

(1) Download OCX

First, user has to log in with the Infinova super ID and password

(For more information, please refer to Chapter 4.1 Login). After

successfully logging in, you will be informed that the browsing

OCX is needed, which is pictured as below:

Figure 3-1 OCX Installation

(2) Install OCX

According to the installation information, click “OK” button, then

the system will automatically install OCX. Real-time video is

displayed on the screen as follows after installation.

Figure 3-2 Download OCX

If the installation above fails, move forward according to the

following steps to continue:

(3) Install DirectX End-User Runtime (Directx 9.0c) version 9.0c

or above, which can be downloaded at

http://www.microsoft.com/downloads/details.aspx?FamilyId=0A9B

6820-BFBB-4799-9908-D418CDEAC197&displaylang=en

(4) Install Microsoft NET Framework Version 1.1 Redistributable

Package, which can be downloaded at

http://www.microsoft.com/downloads/details.aspx?FamilyID=262d

25e3-f589-4842-8157-034d1e7cf3a3&displaylang=en

Both of the two softwares above are in English and free of charge.

As for the Chinese version, available link is provided on the same

page.

1RWH The steps mentioned above are not in sequence. Please try

step 1 and 2 first, and if it fails, you can proceed with step 3 or 4.

The preparation of IE image browsing comes to and end.

3.2 Set IE Browser

You can watch the images and relative interfaces that caught by

camera over IE browser or a kind of special software V2216, based

on the applicable network to browse and control the video image. If

the installation of OCX is done, the user also has to set the security

property of Internet browser.

(1) As shown in the following figure, kick the “Tool” in the menu

bar, and ten click the pop-up Internet option.

Figure 3-3

(2) Select “Security” in the pop-up Internet options, as shown in

the following figure:

Figure 3-4

(3) Click “Custom Level” to pop up the following interface in

Figure 2-5:

Figure 3-5

(4) Enable or Prompt the option of “Download unsigned ActiveX

controls”.

(5) Select “low” in the “Reset custom settings”.

Chapter IV Basic Function Operation

This chapter mainly introduces the settings and operation of

V1492N-N Integrated High-speed IP PTZ Camera.

4.1 Login

Please open IE browser after it powers on for about 50 seconds and

enter http://192.168.1.100/ (the default IP address) in the IP address

for example.

Note: The language of webpage will be different based on operating system.

That is, the interface is in English to English operating system and in

Chinese to Chinese operating system. We introduce the English interface in

this manual. The login dialog box displays as below:

Figure 4-1 User Login

If this is the first time to run the software, you should enter the

default super username and password. The default ID is admin

(password: admin). Click ‘OK’ button to log on. If the username or

password is not correct, the system will return to the above dialog

box.

Click ‘Reset’ to clear the old username and password, and then

enter the new username and password.

(1) If login as the super user, the following interface will display:

Figure 4-2 Super User Interface after Login

(2) If login as the common user, the following interface will

display:

Figure 4-3 Common User Interface after Login

After login successfully, you can click “MJPEG” button to enter

real-time video interface under M-JPEG format as shown in figure

4-4.

Figure 4-4 M-JPEG interface

User can enter system setting interface by click the button

“Settings” above the video image.

System setting interfaces of super and common user are shown as

follows:

Figure 4-5. Setting Interface for Super User

Figure 4-6 Setting Interface for Common User

In the “settings” interface, Super user can perform the following

functions: browsing system information, user management

(add/delete user, change password), device address/protocol/ baud

rate setting, Network settings (including IPv4 network setting,

SMTP settings, FTP settings, SNMP Settings), alarm setting,

Optimize setting, time-zone and time synchronization settings,

system log view, Deinterlaced setting, SD card and Recording

Control, Security settings and Advanced setting (including Software

update, Factory settings and reboot).

Common user only can view system information, change his own

password, and view system log.

1RWH The following descriptions are used for the super

user.

4.2 System Information

The initial interface of System Settings displays related system

information. You can get to know most of system information from

this interface such as: basic information of system, network setting,

NTP setting, video parameter setting, alarm setting, H.264 video

settings, M-JPEG video settings etc.

4.3 Account Settings

After logging on as a super user, click the button.

When the button turns to be high light, the following account

information will display:

Figure 4-7 Account Setting

$GG8VHUV

Note: support a maximum of 8 accounts. stands for super user,

while stands for common user.

(1) Click “ ”, enter the interface of “Add a User”.

Figure 4-8 Add User

(2) Enter the desired User Name and Password (Special

characters are not allowed to appear in User Name or

Password, and number of password characters can be from

8-20.)

(3) Click “OK” button. If the setting is successful, the new user

name will appear in the following account list. Take adding

“USER1” as the new user for example.



Figure 4-9 Add User

(4) If the user exists, the following interface will display:



Figure 4-10

Click “OK” button, the image will be back to Figure 4-9.

If the 9th user is to be added, the following box will pop up:

Figure 4-11

'HOHWH8VHUV

1RWH Only super user can delete common user, plus super user

cannot delete other super user.

Click button behind the common user you want to delete in

the account list, then the following figure will display:

Figure 4-12

Click “OK” button, the selected user would be deleted and the

account list would be automatically updated.

8VHU3DVVZRUG&KDQJH

Click button in the account list, the dialog box of Edit User

Information will pop up:

Figure 4-13

Input the old password, enter your desired new password for twice

and then click “OK” button, the following picture will appear:

Figure 4-14

,PSRUWDQWQRWHV

1) Super user’s password can only be edited by himself.

2) Common user’s password can be edited by both super user and

himself.

For the sake of safety, please change the password as soon as

possible.

4.4 Network Settings

Click button in the navigation bar, the following

interface concerning network parameter would display:

Figure 4-15

0$&DGGUHVV

0$&$GGUHVVdisplay MAC address of the device.

,3YVHWWLQJ

Figure 4-16

Users can set IP address, subnet mask and gateway of Ipv4.

$GGUHVV7\SH display the way of IP address distribution: manually

configured or DHCP dynamic distributed. If “manually configured”

selected, relevant settings can be set in the following fields.

8QLW,3 DGGU HVV used to set the IP address of V1492N-N

Integrated High-speed IP PTZ Camera.

6XEQHWPDVN used to set subnet mask of V1492N-N Integrated

High-speed IP PTZ Camera.

*DWHZD\, 3DGGU HVV used to set the gateway address of

V1492N-N Integrated High-speed IP PTZ Camera.

When all settings are finished, click “Set” button. The following

interface will appear:

Figure 4-17

Click “OK” button, the system will skip to login interface

automatically.

1HWZRUN/LQN

Figure 4-18

In this interfaceˈuser can choose the Network Link modes. There

are five modes are available:

˄1˅10M-half

˄2˅10M-full

˄3˅100M-half

˄4˅100M-full

˄5˅Auto

1RWHOnly the super user can set this option.

)73VHWWLQJV

Figure 4-19

V1492N-N series IP PTZ camera has the function of alarm

associated with FTP upload.

Configure server IP, user name and password in the FTP settings

and enable FTP alarm in alarm settings, then alarm associate with

FTP upload can be achieved.

60736HWWLQJV

Figure 4-20

zServer IP: Set mail server address.

zFrom: Set sender’s mail address.

zTo: Mail address of recipient.

zCC: Mail address of the person copy to.

zAuthentication: Enable or disable authentication function. This

function should be set according to authentication requirements

of mail server.

zUser name: Sender’s name, it can be set according user’s needs.

zPassword: Set sender’s password.

zNote: there is no limit for Sender’s name and password settings.

After setting completes, click “Set” button to take effect.

If user selects “mail” in “Alarm Settings” interface, system will

send mail according to SMTP settings.

61036HWWLQJV

V1492N-N Integrated High-speed IP PTZ Camera has the heartbeat

function.

In the SNMP Settings interface, start the heartbeat server, set its IP

address and the heartbeat interval, and then heartbeat package will

be sent to the appointed server or the client at the specified interval

so that the server or client can easily know about the network status

of the camera.

4.5 Time Settings

Click button in the navigation bar to display the

following Time Zone Settings interface:

Figure 4-21

7LPH] RQH Select the desired time zone in the scroll box, and then click

“Set” to save it.

There are 33 time zones for selection: GMT-12:00~GMT~GMT+13:00, and

the default setting is GMT Greenwich Mean Time.

For Daylight Saving Time enable region, please tick “Automatically adjust

clock for daylight saving changes”.

6\QFKURQL]HZ LWKFR PSXWHUWL PH used to check whether the time of

system is the same as that of local PC. Click “Set” to adjust.

6\QFKURQL]HZLWK173VHUYHU whether to select NTP server or not. Select

“NTP” to enable NTP server, or otherwise disable NTP server.

If NTP server is selected, you can input NTP server address into IP bar.

Click “Set” to finish. If so, the system will adjust time with NTP server

automatically.

4.6 Alarm settings

Click button in the navigation bar to display the

following Alarm Settings interface:

Figure 4-22

I /O In: Settable 2-channel alarm input In1/In2.

Each alarm input has 2 modes

(1) Grounded Circuit

(2) Open Circuit

Recommended: Grounded Circuit

Alarm out Contact: used to set sending way of alarm.

Local Contact: I/O out is triggered by I/O alarm in or motion

detection alarm. Default: Local Contact.

Net Contact: I/O out is controlled by the surveillance

management software.

Note: This function needs to be supported by digital video

surveillance management software like V2216. If Net Contact is

selected, user has to set Alarm Server IP the same as the IP address

of V2216-CMS server. After setting finished, user can remotely

control the relay via V2216 software. For detailed information,

please refer to V2216 manual.

Alarm Server IP: used to set the IP address of alarm server when

NET contact is selected. If alarm occurs, it will inform the alarm

server.

Users can set alarm handling ways for alarm input or motion

detection alarm, like sending Mail, FTP upload, audible alarm,

Relay output After setting completes, click “Set” button to take

effect.

4.7 PTZ Settings

Click button in the navigation bar to display the

PTZ Setting box:

Figure 4-23 PTZ Interface

Camera Address: set the distributed address of V1492N-N

Integrated High-speed IP PTZ Camera. The number of camera

address is determined by different control protocol.

Baud rate: set the communication baud rate of control and camera

modules, the default value is 2400 bps.

Protocol: select the corresponding protocol of camera. The built-in

service software in this IP PTZ camera supports Pelco-P, Pelco-D

and Infinova.

4.8 System Log

Click button on the navigation bar to enter the

system log interface shown as below:

Figure 4-24

It can display 30 logs on a page. User can turn over the page by

clicking the below arrows or skip to the designated page by clicking

“Goto”. Click “Delete logs”, a prompt will come out. Then, click

“Yes” to clear logs.

4.9 Deinterlaced Settings

Click button, and then comes out the deinterlaced

settings interface:

Figure 4-25

It’s recommended to enable the Deinterlaced setting for many

dynamic scenes and disable it for static scenes. Defaulted as: “ON”.

Note: Only the super user can set this option.

4.10 SD Card

Click the “SD Card” button to display the following interface:

Figure 4-26 SD Card

You can view the total size and free space of SD card, and can also

format it.

To remove the SD card during working, please click “Safe pull out

SD card”.

4.11 Recording Control

Click the “Recording Control” button to display the following

interface:

Figure 4-27 Recording Control

Recording Storage Mode: Circle Mode or Stop Mode. Circle Mode

means when the SD card is full, the newly recorded files can

automatically overwrite the existing files; Stop Mode means when

the SD card is full, it stops recording automatically.

Manual Recording Control: Start or Stop recording.

Alarm Recording: Enable or disable automatic recording during

alarm.

Automatic Recording when Network anomaly: Enable or disable

automatic recording during network abnormity.

Note: It only supports recording of minor stream. If the resolution

of minor stream is set “OFF”, recording cannot be performed.

4.12 Security

Figure 4-28 Security

V1492N-N Integrated High-speed IP PTZ Camera is compatible

with https and 802.1x protocols. In the Security interface, you can

make relevant settings for https and 802.1x protocols.

4.13 Advanced Settings

V1492N-N series provides a series of advanced functions, such as Software

Update, Factory Settings and Online Reboot.

Click button to enter the interface shown below:

Figure 4-29

6RIWZDUH8SGDWH

Free software update is provided for V1492N-N series IP PTZ

cameras, and this update service can reduce system maintenance

budget. You can download the latest software from the Internet.

Follow the steps below to update software:

Figure 4-30

Click “Browse” button above, then select program update in the

pop-up dialog box. After that, click “Upload” button, the system

begins to update.

If update successfully, the following information will appear on the

current interface:

Figure 4-31

If the type of updating file is wrong, the following information will

come out:

Figure 4-32

At this time, re-check the updating file and camera system, or

otherwise choose other program to update.

1RWHAfter update successfully, it needs to restart the system.

)DFWRU\6HWWLQJV



Figure 4-33

Click “Set” button, the following hint would display:

Figure 4-34

Click “OK”, system starts to reset to the factory default. It takes

about 15 seconds to undertake this process, when finishing, the

figure below would appear:



Figure 4-35

Click “OK” button to close the webpage.

1RWH When factory setting is finished, IP address resumes to

192.168.1.100, while subnet code resumes to 255.255.255.0.

2QOLQH5HERRW

Figure 4-36

Click “Reboot”, the system will be automatically re-started. And

after 80 seconds the webpage closes.

Chapter V H.264 Video Settings

When login successfully, the interface will be”H.264” (as shown in

figure 4-2 or 4-3). It can switch to full-screen mode by double

clicking the video window, and exit full-screen mode by double

clicking again. A serial buttons on the left help you to set

concerning parameters such as video setting, motion detection,

Privacy masks, OSD, audio, stream type, player and so on.

The system supports dual encoding stream, and it can set video

parameters under Major stream and Minor stream separately. Below,

take the video settings under Major stream as an example.

Common user is just able to set the four items: video size, stream

type, audio and player.

5.1 Video Size

Click the “Video Size” button in the navigation bar to display the

following interface:

Figure 5-1

Enter the desired value in the Width and Height field, and click

“Set” to confirm.

A 704*576 picture indicates 704 pixels in width, and 576 pixels in

height. Other settings are alike in signification.



5HFRPPHQGHGVHWWLQJV

704*480 (NTSC format) or 704*576 (PAL format)

The selectable video image sizes include:

NTSC: 704*480, 704*240, 352*240;

PAL: 704*576, 704*288, 352*288, 176*145.

5.2 Player

Click “Player” button, and Player setting interface will be shown as

follows:



Figure 5-2

Users can select player to play video:

,QILQRYD3OD\HU Choose Infinova player to play video.

4XLFN7LPH: Choose Quicktime Player to play video.

1RWH Available merely for the super user.



5.3 Stream Type

Click “Stream Type” button, and Stream Type interface will be

shown as follows:



Figure 5-3

There are two options: Major stream and Minor stream.

1RWHOnly the super user can set this option.

5.4 Motion Detection

Click ǏMotion Detection ǐ button to display the following

interface regarding motion detection sensitivity:

Figure 5-4

6HQVLWLYLW\: set the sensitivity, the value is between 1 and 30.

Recommended setting: 15



0RWLRQGHWHFWLRQDU HD Two coordinates determine an area.

The line between those two points is the diagonal of detection area.

Each point extends along 2 lines perpendicular to the X-axis and

Y-axis, and the rectangle formed by those 4 crossed lines is the

motion detection area.

If there is any motion detection alarm in the preset area, the alarm

icon on the webpage will turn red . If it’s normal, the icon is

grey .

>21@ Open motion detection alarm.

>2))@ Close motion detection alarm.

1RWH If the motion detection alarm is on, you need to wait about 5

seconds for motion detection alarm checking.

Page is loading ...

Infinova V1492N-28N05 Operating instructions

Brand: Infinova

Model: V1492N-28N05

Category: Security cameras

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Infinova V1492N-28N05 Operating instructions

This manual is also suitable for

Infinova V1492N-28N05 Operating instructions

Related papers

Other documents