Tesco VCUP15 Upright Bagless Vacuum User guide

Brand: Tesco

Model: VCUP15 Upright Bagless Vacuum

Category: Vacuum cleaners

Type: User guide

Tesco VCUP15 Upright Bagless Vacuum is a powerful and versatile cleaning appliance that is suitable for both carpets and hard floors. It features a high-efficiency motor that generates strong suction to remove dirt, dust, and debris effectively. The vacuum cleaner comes with a variety of attachments, including a crevice tool, furniture tool, and upholstery tool, which allow you to clean hard-to-reach areas, upholstery, and delicate surfaces. The lightweight design and swivel steering make the vacuum easy to maneuver around furniture and obstacles.

Upright Vacuum Cleaner

USER GUIDE

VCUP15

Page 2

IMPORTANT SAFETY INFORMATION

To reduce the risk of fire, electrical shock, or injury:

Read all the instructions carefully before using your appliance and

keep them for future reference. If you pass the product on to a third

party, include this manual.

This appliance can be used by children aged from 8 years and above

and persons with reduced physical sensory or mental capabilities or

lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children

without supervision

Unplug the appliance from the mains supply when not in use,

removing or attaching filters, accessories, the dust cup and before

cleaning any part of the appliance.

When unplugging, hold the plug top, not the power cord.

Do not immerse the body of the cleaner or the electrical cord or plug

in water or liquids.

Do not use outdoors in damp or wet weather

Do not use your appliance indoors in damp or wet conditions.

Do not use attachments or accessories not recommended by the

manufacturer.

This appliance is for household use. Do not use for any purpose not

expressly specified in this manual.

There are no user serviceable parts in this appliance. Unauthorised

dismantling or servicing will void the warranty.

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person in

order to avoid a hazard

Refer all servicing which involves the taking or putting on of parts

(other than those specifically referred to in this manual), to a

qualified repair person or approved service centre.

Do not use attachments or accessories which are not recommended

by the manufacturer. They may cause malfunction or injury.

Do not use harsh abrasives, or caustic cleaners when cleaning this

appliance.

Store the appliance away from direct sunlight.

Electrical Information

Before using this appliance ensure the voltage of your electricity supply

is the same as that indicated on the rating plate.

When operating your cleaner:

Never leave the cleaner unattended when it is connected to the

electricity supply.

Do NOT use the vacuum cleaner if it has been dropped, damaged, left

outdoors, or dropped into water.

Do NOT pull or carry the cleaner by the cord, close a door on the cord,

or pull the cord around sharp edges or corners. Use the handle to

carry and move the cleaner.

Do NOT run the appliance over the power cord.

Do NOT handle the mains plug or cleaner with wet hands.

Do NOT use the vacuum cleaner to pick up large objects or objects

that are likely to damage the vacuum cleaner.

Do NOT attempt to vacuum long hair, string, pieces of cloth, etc.

when vacuuming carpets or floors. These may clog the cleaner.

Keep hair, loose clothing, jewellery, fingers, feet and all parts of your

body away from openings and moving parts.

Do NOT vacuum hot items; e.g. cigarettes, matches, ashes.

Do NOT vacuum hard or metal objects, nails pins, etc.

Do NOT pick up toxic, or flammable materials or use in the presence

of explosive or toxic dust, liquids or vapour.

Use only on dry, indoor surfaces.

Do NOT put any objects into openings.

Do NOT use without all the filters in place or with any filter blocked.

Before use check that the dust cup is empty and empty it frequently

during use.

Switch the cleaner off before plugging or unplugging the vacuum

cleaner into the mains supply.

Use extra care when vacuuming on stairs.

Keep all vents openings and attachments free of dust, lint, hair and

anything else that may reduce air flow.

Keep the end of the hose and all attachments away from your face

and body.

If the appliance becomes clogged, switch off and unplug the power

cord before clearing the obstruction.

IMPORTANT- PLEASE READ

For efficient operation it is essential that all the airways and filters are

cleaned regularly and that the dust container is emptied before it is

full and after every use of the appliance. Failure to do this will restrict

the airflow and result in poor cleaner performance.

Damage caused by failure to empty the dust container and to clean

the filters and airways as specified in these instructions will not be

covered by the warranty.

AUTOMATIC SHUT-OFF THERMOSTAT

There is a safety thermostat inside the cleaner to prevent the unit

from being run with too high a vacuum rate. If the airways or filters

get clogged the pressure in the cleaner will be excessive and the

thermostat will activate. The cleaner then will stop working to

protect the motor from overheating.

If this happens switch off and unplug the cleaner immediately. Allow

the motor to cool down for one hour and clean the airways and filters

thoroughly. Plug the cleaner in again and switch on: the cleaner

should now operate normally.

Your Vacuum Cleaner and its accessories.

Unpacking

Unpack the appliance and accessories. Retain the

packaging. If you dispose of it, do so obey recycling

regulations. Identify the cleaner components from the

illustrations.

If items are missing or damaged, contact your nearest Tesco

store for assistance. Please have your receipt ready when

you call.

Page 3

Hose

Nozzle

Dust Filter

Handle

IMPORTANT NOTICE - PLEASE READ BEFORE USING THIS PRODUCT!

THIS CLEANER WORKS BY SUCKING AIR AT HIGH PRESSURE THROUGH A POWERFUL MOTOR. FOR

EFFICIENT AND SAFE OPERATION IT IS ESSENTIAL THAT ALL THE AIRWAYS AND FILTERS ARE CLEANED

AT REGULAR INTERVALS AND THAT THE DUST IS EMPTIED BEFORE THE DUST CUP IS FULL.

FAILURE TO CLEAN THE AIRWAYS AND EMPTY THE DUST CUP IN GOOD TIME WILL RESTRICT THE

AIRFLOW AND RESULT IN POOR CLEANER PERFORMANCE.

LONG TERM NEGLECT WILL BLOCK THE AIRFLOW AND MAY DAMAGE THE CLEANER BEYOND

REPAIR. DAMAGE CAUSED BY FAILURE TO REPLACE THE DUST CUP AND TO CLEAN THE FILTERS, AND

AIRWAYS AS SPECIFIED IN THESE INSTRUCTIONS WILL NOT BE COVERED BY THE WARRANTY.

Power

Head

Multi Tool Accessory

Motor Filter

& Cage

Used as a crevice tool

(remove or fully retract)

As a furniture tool

(Pull out until

the catch clicks in)

As a furniture brush

(Remove. Reverse the

tool. Push it back

until the catch clicks)

VCUP15 Vacuum Cleaner User Guide

Lower Hose

Power Cord

Hook

Hose Clip

Upper Power

Cord Cleat

Lower Power

Cord Cleat

Power Cord

Flexible

Hose

Multi Tool

Power On/Off

Switch

Hose

Collar

Dust Cup

Dust Cup Lid

Pressure Release

A: Detach the Dust Cup. Press

the catch down and remove the

Dust Cup from its cradle.

B: Place the handle on the body

and press down firmly so that the

handle clicks into place. Pull the

handle up slightly to check that the

handle is securely attached to the

body.

C: Replace the Dust Cup and

check that it is seated firmly.

D: Secure the handle to the

cleaner with the provided screw.

E: Place the extension hose

collar with the slot over the

locating lug on the lower hose

tube. Press in and rotate so that

the collar locks securely.

F: Dress the extension hose over

the hose clip as shown. When

not in use the hose should

always be attached in this way to

minimise accidents.

G: Push the hose nozzle firmly

into the sleeve on top of the

lower hose.

H: Place the multi tool onto the

tool post which is located in front

of the extension tube nozzle.

I: Set the cleaner upright.

Place your foot over the  mark

on the power head and press

down. Now angle the cleaner

fully upright until it clicks into

place. Always make sure that the

cleaner is upright before

winding/unwinding the power

cord, operating the cleaner or

for storage.

J: Remove the plastic tie from

the power cord and uncoil the

cord fully. Make sure the upper

cleat is set vertical and wind the

cord over the upper and lower

cleat.

Assembling your Vacuum Cleaner

Page 4

VCUP15 Vacuum Cleaner User Guide

B CA

Set the cleaner upright before you commence.

A: Rotate the upper cord holder to release the power cord. Uncoil the

power cord fully.

B: For convenience, you may hook the cable over the cable hook on

the rear of the handle. This will help stop the cable snagging.

Plug the power cord into the electrical outlet. Switch on at the mains

point.

Vacuuming Carpets and Floors

Always check the carpet or floor covering manufacturer's

recommended cleaning instructions before vacuuming. Be

especially careful when vacuuming polyester or low melting

point (LMP) polypropylene carpets as the powerful brush could

cause carpet burn.

C: With your foot, depress the Power On/Off

switch. Press to switch the cleaner ON. Press

again to switch the cleaner OFF.

D: Place your foot over the “shoe“ icon on the

power head and lightly press down. The

cleaner can now be angled as required

E: The cleaner can be freely angled vertically

and also swivelled to assist you in getting to

those hard to reach areas.

Using the accessories

1: Switch the cleaner OFF.

2: Place the cleaner in the upright position.

3: Free the hose from the clip at the top

4: Lift off the multi tool.

5: Lift out the hose from the mounting at the side of the cleaner.

6: Switch the cleaner ON

The hose can be used with the nozzle alone or with the multi tool fitted.

7: The multi tool can be used:

$ As a crevice tool to vacuum down the side of cushions, etc.

$ As a brush for furniture and small objects.

$ As an upholstery tool for soft furniture. Do not use it on fabrics that

may snag or on polished surfaces which may scratch.

(Refer to Page 3 for further details)

Page 5

Using your Vacuum Cleaner

VCUP15 Vacuum Cleaner User Guide

Vacuuming Stairs

The cleaner hose will not reach all

the way up a standard flight of (13)

stairs. The stairs should be cleaned

a few stairs at a time from the

bottom to the top using the

accessory tool.

1: Place the cleaner at the bottom

of the stairs with the rear of the

cleaner resting against the first step.

2: Plug the cleaner in. Switch it on

3: Support the cleaner with one

hand and vacuum a few (3-4) stairs

being careful not to overstretch.

Never clean the stairs with the cleaner more than one

stair above you as the cleaner could topple and

cause injury or damage.

4: Switch off and move the cleaner onto the highest stair you

have just cleaned. Place the

cleaner with the rear of the

cleaner resting against the step

above.

5: Stand beside or one step

below the cleaner. Support the

cleaner with one hand and

vacuum a few more (3-4) stairs.

Be careful not to overstretch or

over- balance.

6: Repeat the process until you

reach the top of the stairs.

7: Now switch the cleaner off,

unplug and wind the power

cord.

8: Replace and stow the hose

and multi-tool.

Emptying the Dust Cup

Empty the dust cup regularly to maintain the efficient

performance of the cleaner. Failure to do this may impair the

efficiency of the cleaner.

The maximum dirt level is marked on the

Dust Cup. Empty the Cup before the dirt

reaches the MAX mark.

$ Switch the cleaner off and unplug it

from the mains.

$ Set the cleaner upright and ensure it is

locked in place.

Hold the Dust up by the handle and

press the dust cup release catch.

Hinge the cup out of its cradle.

Carefully remove the dust cup from the

cleaner, keeping it vertical.

Invert the dust cup over a bin.

Release the catch on the bottom lid.

Shake and tap the dust cup lightly to

remove as much dust as possible.

Close the lid.

If you are still vacuuming, replace the cup.

Cleaning the Dust Cup and Filter

When you have finished cleaning you must clean the HEPA filter

in the dust cup after emptying it. This is essential.

The HEPA filter traps up to 99% of particles as fine as 0.3

microns. This includes mites, pollen grains and fine hairs.

Because of this very high level of filtering it is essential that you

clean the filter regularly to maintain efficient filter performance.

Remove the Dust Cup from the cleaner and empty it.

Place the Dust cup on a worktop or sturdy

table.

Unclip the lid catch and hinge the lid

back as far as it will go.

Do NOT use force!

General Do's and Don'ts

$ Do NOT pull the vacuum cleaner around the room by the

hose as it could tip over and cause damage.

$ Do NOT over extend the hose. Trying to reach beyond the

hose length could cause the vacuum to tip over.

$ Do NOT pull or carry the cleaner by the cord, close a door

on the cord, or pull the cord around sharp edges or corners.

$ Always use the handle when lifting or moving the cleaner

between different locations. Do not lift the cleaner with the

dust cup handle on its own.

$ Never clean the stairs with the cleaner more than one stair

above you as the cleaner could topple and cause injury or

damage. Follow all the instructions on the previous page.

$ Before moving the cleaner a long way or up or down a flight

of stairs,

$ As soon as you have finished using the hose, replace the

nozzle and mufti tool and put the hose back in its clip .

IMPORTANT NOTE WHEN USING THE ACCESSORIES

Never attach or remove accessories when the vacuum

cleaner is switched on.

The cleaner is fitted with a spring loaded deflection plate located

under the cleaner. When the cleaner is set upright this plate and

the small wheels under the cleaner keep the brush clear of the

floor surface minimising the likelihood of floor damage. See P 8

Always have the cleaner in

the upright position when

u s i n g t h e h o s e a n d

acce ssory tools. If the

cleaner is operated so that it

is tilted forward the brush

will dig into the floor surface

and could damage it. There

is also the possibility that the

cleaner may tip over.

Page 6

VCUP15 Vacuum Cleaner User Guide

Hold the HEPA filter

cage by the two finger

grips and lift it out of the

cup.

You should now remove

t h e c y c l o n e f i l t e r

assembly. Open the

base of the Dust Cup

and push t he fil ter

assembly out.

Hold the assembly in

both hands.

Rotate the lower section

of the filter anticlockwise

and separate the two

sections of the filter.

Rinse both sections of the cyclone filter assembly under the tap in

lukewarm water to remove any dust. The dust cup and dust cup

cover can also be washed in lukewarm water. Allow all sections

to dry fully before re-assembly

Cleaning the SMS Filter

At least once a month or when you notice a decrease in suction,

wash the SMS filter by running it under the tap.

The filter is in two sections. Invert the filter and lift out the inner

black filter. This filter has a rough and a smooth side. The rough

side faces down (into the Dust Cup).

Brush out both sections of the filter with a soft brush. If the filters

are soiled, wash them under running water until they are

thoroughly clean. Do not use strong detergents. DO NOT place

any part in a dishwasher. Allow all parts to fully dry before re-

assembly. This may take up to 24 hours. Only when the filter is

dry should you replace them in the Dust Cup.

The white filter will discolour over time. Although this does not

indicate a loss in effectiveness, the filter should be replaced at

least every six months to keep your cleaner in peak condition.

When all components

are dry, re-assemble

the filter and Dust

cup reversing the

instructions at the top

o f t h e p r e v i o u s

column.

Now replace the Dust

Cup in the cleaner.

Cleaning the Motor Filter

Unplug the cleaner from the mains supply.

The motor filter is located in a cage above the power head at the

front of the cleaner.

Slide the catch at the

bottom of the cage to the

left to unlock it and then lift

it out.

Brush out any debris

carefully from the grille

behind the filter cage.

Remove the filter from the

cage. Brush out the filter

And the filter cage with a

soft brush. If the filters is

soiled, wash it under

running water until tit is

clean. After washing allow

both parts to fully air dry.

(This may take up to 24

hours.) Only when the

filter is dry should you

replace it in the cleaner.

Replace the filter in the cage (with the rough side facing inward).

To replace the cage, align

it into the recess at the top

and hinge it shut. Now

fasten the catch by sliding

it to the right.

Page 7

VCUP15 Vacuum Cleaner User Guide

LOOSE

TIGHT

FILTER COMPONENTS

VCUP15 Vacuum Cleaner User Guide

Clearing a Blockage

If the cleaner loses suction and the dust in the dust cup is below

the MAX mark, this may be due to a blockage.

DO NOT operate the cleaner if the suction is impaired.

$ Set the cleaner upright, switch off and unplug immediately.

$ Empty the dust, check and clean all the filters.

$ Disconnect the hose to see if debris has backed up.

$ Examine the multi tool.

$ Remove any blockage with a stick or broom handle.

If all the above seem clear, the lower hose may be blocked.

Pull the lower hose collar off the

inlet pipe. The fit is intentionally

tight.

Clear the blockage and replace

the hose.

If you notice that the brush speed is slow and/or there is a

loss of suction, this may be due to the brush getting clogged.

Prompt action will maintain cleaner performance and avoid any

potential problems of belt slippage.

Switch the cleaner off and unplug it from the mains.

Check that the

deflection plate

m o v e s f r e e l y.

Clean the brush

area and remove

all obstructions

before continuing

to use the cleaner.

IMPORTANT-Motor Thermostat

If the vacuum cleaner should overheat, the protective

thermostat will automatically turn the unit off.

If this occurs: Switch off and unplug. Check and clear any

blockage and clean/replace the filter.

Wait at least 45 minutes before attempting to reuse the

cleaner. After the cleaner has cooled down plug in and switch

on. The vacuum should now start.

DEFLECTION PLATE

Changing the Drive Belt

Sluggish speed and loss of suction may be caused by a worn or slack belt. A spare belt is provided.

DO NOT replace this components yourself unless you are confident that you can carry out this procedure satisfactorily.

Make sure the cleaner is switched off and unplugged from the mains before you start work. Protect the work surface if necessary.

You need a No2 Phillips screwdriver to carry out this procedure.

Stage 1. Remove the Cover Plate

Remove the Dust Cup.

Angle the cleaner fully back.

Turn the cleaner over and place it on a stout work bench

The cover plate is attached to the cleaner with six screws.

There are identified below (you can only access the centre

screw by first lifting up the deflection plate).

1: Remove all six screws and keep them safe

2: Ease the cover plate off to expose the brush and roller

Page 8

Stage 2. Remove the Brush

Ease the Right end of the brush out of its bearing.

Repeat for the Left edge.

Now lift out the brush with both hands. Be careful as the belt is still under tension.

Pull out the brush from the belt.

VCUP15 Vacuum Cleaner User Guide

Stage 3. Remove the Belt

Inspect the belt for wear. If the inside of the belt is very shiny but otherwise unworn and free from

nicks or tears, you may be able to extend its useful life by turning it inside out.

If you are not replacing the belt, clean it carefully with a dry cloth to remove any residue but do not

remove the belt..

When you are removing or replacing the belt, twist the belt on its side and slide the edge of the

belt around the end of the spindle.

(You may find it easier to cut the belt off with a pair of sharp scissors.

Manoeuvre the belt over the spindle, straighten it

out and lay the belt flat on the spindle.

Thread the brush through the belt.

Position the belt over the convex section of the

brush . Make sure the belt is not twisted

Stage 4. Replace the belt

Stage 5. Replace the brush

Insert the brush into the belt.

A. Hold the brush in both hands. Pull the brush towards you and partially insert the left hand side bearing of the brush into its socket

with your thumb. (This will place the belt under tension, so you may have to use moderate pulling force.)

B: Align the Right Hand side of the Brush over the Bearing and pressthe brush into place.

Press sides of the brush fully home.

Finally, rotate the brush by hand to ensure that the mechanism moves freely and that the belt does not foul the guides and is central

on the motor spindle.

Page 9

VCUP15 Vacuum Cleaner User Guide

Stage 6. Re-assembly

Rotate the brush by hand to ensure that the mechanism moves freely and that the belt does not foul the guides and is central on the

motor spindle.

Now replace the cover plate .

Place the cover plate into position and press the plate to the cleaner body all round to ensure a good fit.

Screw the plate to the cleaner body. Remember the screw under the deflection plate.

Before using the cleaner, switch it on and confirm that the brush rotates freely and that the brush height mechanism operates properly.

Warranty

This appliance is intended only for household use. It must be

properly installed and operated in accordance with these

instructions. Failure to do this will invalidate the warranty.

Your appliance is covered by a warranty for 12 months from the

date of purchase. If a fault develops during this period, please

return the unit to your nearest Tesco store together with the

original receipt as proof of purchase. This warranty in no way

affects your consumer rights

UK: Waste electrical products should not be disposed

of with household waste. Separate disposal facilities

exist, for your nearest facilities see www.recycle-

more.co.uk or in-store for details.

ROI: Produced after 13th August 2005. Waste

electrical products should not be disposed of with

household waste. Please recycle where facilities exist.

Check with your Local Authority or retailer for recycling

advice.

Specifications

Voltage: 220-240 V AC 50Hz

Net Weight: 4.5 kg

Product Fiche

Class II construction double insulated. This product must

not be connected to earth.

OPERATING CAUTIONS

$ NEVER operate the cleaner with damaged filters or with a

filter missing

$ Use approved filters and regularly clean and replace them.

$ Wind the cord around the cleats after use.

If an obstruction occurs during cleaning: Turn the cleaner

OFF and unplug. Check the dust level. Empty the dust cup.

Check the hose and the tubes for blockage and clear these

manually following the instructions above.

After Use

Set the cleaner fully upright. Switch the cleaner off. Unplug from

the mains. Set the cleats vertical and rewind the cord around the

cleats. Empty the dust cup and clean the dust cup filter

Re-assemble the hose and attachments if necessary.

Wipe the cleaner body with a damp cloth and dry thoroughly.

Store the cleaner safely out of the reach if children and pets.

Cleaning and storage

$ The plastic outer body shell and the exterior surfaces of the

attachments may be cleaned with a barely damp cloth and

then dried thoroughly.

$ Do NOT allow water or liquids to penetrate the vacuum

cleaner. This could be dangerous.

$ Store the appliance away from direct sunlight, and out of the

reach of children.

Trade mark: Tesco

Model: VCUP15

Energy efficiency class: A

Annual energy consumption: 24.1 kWh/annum

Carpet cleaning performance class: D

Hard floor cleaning performance class: C

Dust re-emission class: G

Sound power level: 89dB(A)

Rated input power: 700W

Page 10

Page 8

Tesco Stores Ltd.

Welwyn Garden City AL7 1GA, U.K.

Tesco VCUP15 Upright Bagless Vacuum User guide

Brand: Tesco

Model: VCUP15 Upright Bagless Vacuum

Category: Vacuum cleaners

Type: User guide

Download PDF

report

Tesco VCUP15 Upright Bagless Vacuum User guide

Tesco VCUP15 Upright Bagless Vacuum User guide

Related papers

Other documents