Tesco 2 in 1 Cordless Stick Vacuum User guide

Brand: Tesco

Model: 2 in 1 Cordless Stick Vacuum

Type: User guide

USER GUIDE

Cordless Stick Vacuum Cleaner

CSVC15

To reduce the risk of re, electrical shock, or injury:

Read all the instructions carefully before using your appliance •

and keep them for future reference. If you pass the product on

to a third party, include this manual.

Ensure the appliance is switched o when not in use, removing •

or attaching lters, accessories, the dust cup and before clean-

ing any part of the appliance.

Do not immerse the body of the cleaner or the battery or the •

power supply unit (charger) in water or liquids.

Do not use outdoors in damp or wet weather•

Do not use your appliance indoors in damp or wet conditions.•

Do not use attachments or accessories which are not recommend-•

ed by the manufacturer. They may cause malfunction or injury.

This appliance can be used by children aged from 8 years and •

above and persons with reduced physical sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the ap-

pliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.•

Cleaning and user maintenance shall not be made by children.•

This appliance is for household use. Do not use for any purpose •

not expressly specied in this manual.

There are no user serviceable parts in this appliance. Unauthor-•

ised dismantling or servicing will void the warranty.

Refer all servicing which involves the taking or putting on of •

parts (other than those specically referred to in this manual),

to a qualied repair person or approved service centre.

Do not use harsh abrasives, or caustic cleaners when cleaning •

this appliance.

Store the appliance away from direct sunlight.•

Do not expose the appliance to temperatures below 0°C or •

above 40°C.

The appliance is only to be used with the power supply •

unit (Charger) provided with the appliance.

If the power supply unit or DC cable is damaged, it must be •

replaced by the manufacturer or its service agent or a similarly

qualied person in order to avoid a hazard.

When operating your cleaner:

NEVER leave the cleaner unattended.

When using the cleaner as a hand-held appliance store the main ap-

pliance safely out of harm’s way or hang it up on the storage bracket.

Do NOT use the vacuum cleaner if it has been dropped, damaged,

left outdoors, or dropped into water.

Do NOT use the vacuum cleaner to pick up large objects or objects

that are likely to damage the vacuum cleaner.

Do NOT attempt to vacuum long hair, string, pieces of cloth, etc.

These may clog the cleaner.

Keep hair, loose clothing, jewellery, ngers, feet and all parts of your

body away from openings and moving parts.

Wear sensible footwear. Do not operate in bare feet, socks or wear-

ing open toed footwear.

Do NOT vacuum hot items; e.g. cigarettes, matches, ashes.

Do NOT vacuum hard or metal or sharp objects, nails pins, etc.

Do NOT

vacuum

toxic, or ammable materials or use the appliance

in the presence of explosive or toxic dust, liquids or vapour.

Do NOT vacuum toner dust from printers or copiers or vacuum ash or

soot in any form.

Do NOT vacuum insects or any other creatures.

Use only on dry, indoor surfaces.

Do NOT put any objects into openings.

Do NOT use without all the lters in place or with any lter blocked.

Before use check that the dust cup is empty and empty it frequently

during use.

Use extra care when vacuuming on stairs.

Keep all vents openings and attachments free of dust, lint, hair and

anything else that may reduce air ow.

Keep all attachments away from your face and body.

If the appliance is clogged, switch o before clearing the obstruction.

LITHIUM ION BATTERY. DO NOT PUNCTURE, DROP,

PLACE ON HOT SURFACES OR EXPOSE TO HEAT OR WATER.

This appliance uses a Lithium Ion Battery. HANDLE THE BATTERY

WITH CARE. There is a risk of leakage, explosion, re or burns:

If the battery is opened, exposed to heat, re or immersed in •

liquids.

If the battery terminals are short-circuited with a metal object.•

LEAKAGE: If the battery is punctured or mishandled the battery

contents may leak. If battery contents come into contact with skin

or eyes, rinse the aected area continuously for 15 minutes in clean

cold water and seek medical help immediately.

The battery must be disposed only in specially designated disposal

areas. Refer to Page 8 for details concerning battery disposal.

IMPORTANT NOTICE - PLEASE READ BEFORE USING THIS PRODUCT!

CLEAN ALL AIRWAYS AND FILTERS AT REGULAR INTERVALS AND AND

EMPTY THE DUST BEFORE THE DUST CUP IS FULL. FAILURE TO CLEAN

THE FILTERS AND EMPTY THE DUST IN GOOD TIME WILL RESTRICT THE

AIRFLOW AND RESULT IN POOR CLEANER PERFORMANCE.

DAMAGE

CAUSED BY FAILURE TO EMPTY THE DUST AND TO CLEAN FILTERS AND

AIRWAYS AS SPECIFIED

WILL NOT BE COVERED BY THE WARRANTY.

If the appliance malfunctions: Switch it o immediately (and

disconnect the power supply). Seek help as soon as possible.

MPORTANT SAFETY INFORMATION

Page 2

CSVC15 User Guide

Your Vacuum Cleaner and its accessories

FRONT VIEW SIDE VIEW

Preliminaries

Floor Head Power Control

Turbo Speed Button

Handle Folding Button

Handle Folding Hinge

Hand Vac. Release Button

Hand Vacuum Handle

Hand Vac. ON/OFF Button

Dust Cup Release Button

Floor Head

Floor Head Pivot

Floor Head Catch

Wall Mount

Dust Full Mark

Dust Cup & Filters

Battery Release Button

Removable Li-ion Battery

Battery Charging Socket

Floor Head Brush

Battery Charge Indicators

Handle

Remove all packaging from the appliance and accessories. Retain

the packaging. If you dispose of it, do so according to any recycling

regulations.

Identify the cleaner components from the illustrations. If any items are

missing or damaged, contact your nearest Tesco store for assistance.

Please have your receipt ready when you call.

Please read all these instructions before you use your cleaner.

The cleaner is provided with a wall mounting assembly. When the

cleaner is not in use and/or when charging the battery we suggest you

place the cleaner in the wall mount.

Page 3

Note: Actual model may vary

DC POWER SUPPLY

CSVC15 User Guide

Wall Mounting the Cleaner

Assembling The Cleaner

The cleaner should be mounted within easy reach of a mains power

point. When mounted the cleaner should be securely hung on the

mounting bracket with the cleaner oor head resting on the oor.

The wall or other mounting surface should be secure and be able to

stand the weight of the appliance plus a small amount of pulling force.

Screws are provided to attach the mounting bracket, but it is your

responsibility to ensure that they are suitable for use with your wall. If

not, you should provide suitable screws and fastening hardware.

If you are in any doubt as to your ability to safely complete this procedure,

consult a suitably qualied technician.

1: Attach the support bracket to the wall.

Mark a line 400mm above the oor.

Centre the bracket mount on this line as shown and

place the bracket with the top edge horizontal.

Using the bracket as a template mark out the three x-

ing holes. Attach the bracket securely to the wall with

suitable xings. You may need to drill and plug the wall.

400mm to oor

2: Attach the cleaner to the bracket.

Push the mounting boss of the cleaner

into the bracket mount to securely at-

tach the cleaner.

3: The oor head should rest on

the oor for greater security.

1: Remove the Hand Vacuum from the cradle.

Lay the cleaner cradle at on a worktop. Press the “Hand Vac” button and

lift out the hand vacuum from the cradle.

2: Attach the Floor Head.

Turn the cleaner on its front. Press the oor head catch in and then insert

the oor head all the way. Release the catch and check the head is secure.

3: Insert the handle.

Turn the cleaner on its back. Push the handle in as far as it will go.

4: Secure the handle.

Turn the cleaner on its front. Remove the attachment screw from its

plastic bag. Screw it rmly into the hole below the handle. Do not over-

tighten.

5: Stand the cradle upright and replace the hand vacuum.

Assembly is now complete

3 5

Page 4

CSVC15 User Guide

Page 5

Charging the Cleaner Battery

Cleaning Floors and Carpets (Upright Mode)

Make sure the battery is securely attached - refer to Page XX for details on attaching and detaching the battery.1.

Attach the cleaner to the support bracket.2.

Make sure the cleaner power switch is OFF.3.

Fully unwrap the DC power supply cord. Plug the DC socket of the adaptor into the charging point on the cleaner. Now plug the power sup-4.

ply into a mains point and switch on at the mains. Ensure the DC cord is not stretched taut and is unlikely to be pulled out of the cleaner,

Charge the battery for 5 hours or until the battery is fully charged. The battery is fully charged when all the lights on the battery indicator 5.

are lit. Refer to illustration 5 below.

IMPORTANT: Lithium Ion batteries should not be kept “topped up”. Leaving the charger connected to the battery for long periods when the battery is

fully charged will shorten the battery’s useful life. If two lights show on the indicator and if the cleaning job is small, it is better to use the cleaner in this

condition than to continuously charge the battery.

Make sure the cleaner power switch is OFF.1.

Unplug and coil the DC supply cable and 2.

store the power supply.

Lift the cleaner o the support bracket and 3.

place the cleaner on the oor.

Place your foot on the oor head and angle 4.

the cleaner back to unlock the oor head.

Switch the cleaner on by setting the Power 5.

Switch to the “Floor” or “Carpet” position to

suit your oor. (The oor brush operates only

when carpet mode is selected.)

Press the TURBO switch for an extra burst 6.

of power. Press the switch again to cancel

TURBO mode. (To conserve battery life use

this mode only for short periods).

During operation you can rotate the cleaner 7.

around the oor head for ease of cleaning.

By releasing the handle lock you can use the

cleaner to get at all those dicult areas.

Hold the cleaner securely. Press The “FOLD-8.

ING handle” button and rotate the handle

down to free it, DO NOT force it or attempt

to fold it through an angle greater than 90°

or you may damage the appliance.

You can now access all those dicult areas.9.

When you have nished:

Return the handle to the upright position and

make sure it locks in place.

Switch the cleaner o.

Place your foot on the oor head, set the cleaner

upright and make sure it locks in place.

Empty the dust, clean the lters if necessary and

attach the cleaner to the storage bracket after

use

4 5

BATTERY INDICATOR MENU

Top Indicator lit only - Battery needs charging.

Top and Centre indicators lit - Battery is partially

charged. You can use the cleaner for short spells.

All three indicators lit - Battery is fully charged.

You can use the cleaner normally.

Do not overcharge the battery. Disconnect the

charger when all three indicators are lit.

4 5

CSVC15 User Guide

Page 6

Using the Cleaner as a Handheld Device

Cleaning and Maintenance

Make sure the cleaner power switch is OFF. Unplug 1.

and coil the DC supply cable and store the power

supply. Lift the cleaner o the support bracket and

place the cleaner on the oor.

Removing and Replacing the Hand Vac

To remove: Support the cleaner. Hold the Handle of 2.

the Hand Vacuum, press the HAND VAC button and

release the Hand Cleaner from the Frame.

To replace: Place the Hand Vac into the slot in the 3.

frame. Push it back until it clicks into place. Pull it

slightly to ensure it is locked.

Operation

There is an extension tube in the nozzle of the 4.

cleaner. This has two positions - short and extended.

Pull the tube out to select the desired length. En-

sure the tube is locked in position. There is a brush

at the side of the cleaner. If you wish to use the

brush, lift it o and slide it over the extension tube.

Hold the cleaner securely in one hand and press the 5.

ON OFF switch to start the cleaner.

Gently pass the cleaner over the surface. Switch the

cleaner o between operations to conserve battery life.

There is no TURBO mode when the cleaner is handheld.

After Use: Switch o both the power switches.

Replace the extension tube and brush, empty the dust,

clean the lters if necessary.

Replace the cleaner in the main frame and attach the as-

sembled cleaner to the storage bracket after use.

2 3 4

6 8

Removing the Dust

When the Dust reaches the FULL mark you must empty the Dust Cup. 1.

Remove the Hand Vac from the cradle. Hold it over a bin, press the 2.

Release Button and shake all the dust into the bin. Now close the

Dust Cup.

Cleaning the Filters and Motor Cavity

As dust accumulates in the lter, the increased resistance will cause the air

ow to decrease. Clean the lters regularly and ideally after every use.

Press the Dust Cup release button and remove the Dust cup from the 3.

cleaner body.

Invert the cup and remove the black sponge lter.4.

The main lter is a two-part assembly

Pull the inner EPU lter out.5.

Now remove the outer mesh lter6.

Brush out the lters with a soft brush. If they are soiled, wash them 7.

out fully under running water. Let them dry before replacing them.

Never replace a damp lter in the cleaner.

Brush out any debris from the motor cavity.8.

After cleaning, replace the lters

Make sure all lters are dry, Assemble 1.

the two part lter and replace it in

the cleaner. Note the locating spigot

in the outer lter.

Replace the sponge lter. 2.

Return the Dust Cup to the Hand Vac. 3.

Place it into the catch as shown and

press it back until it clicks into place.

Now replace the Hand Vac into the 4.

Frame.

Floor Brush: Cleaning and Maintenance

Hair, threads and bres can clog the brush,

impeding rotation and impairing cleaner

performance. Inspect the brush after every

use and clean it as necessary.

Switch the cleaner o and remove 5.

the Floor Head. from the cleaner.

Place the oor head on a workbench 6.

and hinge the brush retainer clip out.

Carefully ease out the brush with the 7.

aid of a screwdriver or similar tool.

Remove the brush completely. 8.

Remove any adhered items and clean the

brush thoroughly.

Replace the brush. Place the left 9.

side of the brush in the bearing and

then press the brush rmly into

place. Close the brush retainer clip

and check that the brush rotates

smoothly.

Replace the Floor Head. in the 10.

cleaner.

Clearing a Blockage

If the cleaner loses suction this may be

due to clogged lters or a blockage. DO

NOT operate the cleaner if the suction is

impaired.

If you suspect a blockage:

Set the cleaner upright, switch o imme-

diately. Empty the dust, check the lters

and the oor brush and clean them.

If this does not remove the blockage:

Clearing a blockage in the Hand 11.

Vac: Remove the Hand Vac from the

cradle. Remove the lters and open

the Dust Cup. Clear the blockage

with a exible stick.

Clearing a blockage in the Floor 12.

Head: Lean the Floor Head fully

back. Remove the Floor Head from

the cradle. Remove the brush from

the Floor Head. Clear the blockage

with a exible stick.

Reassemble the cleaner when you have

nished and and attach it to the support

bracket.

CSVC15 User Guide

6 7

Page 7

2.75kgs

Tesco 2 in 1 Cordless Stick Vacuum User guide

Tesco 2 in 1 Cordless Stick Vacuum User guide

Tesco 2 in 1 Cordless Stick Vacuum User guide

Related papers

Other documents