IS-42138-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
6) Unscrew the threaded ring[F] from screw collar loop. Take
canopy[G] and pass over screw collar loop. Approximately
one half of the screw collar loop exterior threads should
be exposed. Adjust screw collar loop by turning assembly
up or down in mounng strap. Remove canopy.
7) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
8) Slip canopy over screw collar loop and thread on threaded
ring. Aach chain[I] (open one link[H]) to boom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
9) Adjust chain to desired length by removing chain links and
aach chain to xture with one open link[H], close the
open links by wrapping with a towel and squeezing closed
using pliers.
10) Weave electrical wire and ground wire through chain[I]
no more than 3 inches apart. Pass wire through threaded
ring[F], canopy, screw collar loop, threaded pipe and into
outlet box.
11) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
13) Raise canopy to ceiling.
14) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
15) Aach the curved arms[L] the upper part of the main
body with a nylon washer[Q] using the set screws[M].
16) Take the lower body[P] and place on top of the lower
part of the curved arms with four (4) nylon washers[Q]
using the set screws[M].
17) Take the trim cover[K] and place onto the boom of the
installed lower body and hold in place with the nial[R].
18) Install the recommended bulbs (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain Link
[I] Chain
[J] Large Loop
[K] Trim Cover
[L] Curved Arms
[M] Set Screws
[N] Strap
Mounting
Screws
[O] Main Body
[P] Lower Body
[Q] Nylon Washer
[R] Finial
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take the main body[O] and place one of the trim
covers[K] on top of the main body as shown.
2) Take the large loop[J] and run the wires through its
center and thread onto the installed trim cover.
3) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
4) Run another hexnut down threaded pipe almost touching
rst hexnut. Now screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
5) Connect mounng strap[D] to outlet box using the strap
mounng screws[N].
Installaon Instrucons (connued)
E
D
C
N
A
G
B
F
I
H
H
J
K
L
M
O
P
Q
K
R
M
Q
Page is loading ...
IS-42138-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
6) Unscrew the threaded ring[F] from screw collar loop. Take
canopy[G] and pass over screw collar loop. Approximately
one half of the screw collar loop exterior threads should
be exposed. Adjust screw collar loop by turning assembly
up or down in mounng strap. Remove canopy.
7) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
8) Slip canopy over screw collar loop and thread on threaded
ring. Aach chain[I] (open one link[H]) to boom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
9) Adjust chain to desired length by removing chain links and
aach chain to xture with one open link[H], close the
open links by wrapping with a towel and squeezing closed
using pliers.
10) Weave electrical wire and ground wire through chain[I]
no more than 3 inches apart. Pass wire through threaded
ring[F], canopy, screw collar loop, threaded pipe and into
outlet box.
11) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
13) Raise canopy to ceiling.
14) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
15) Aach the curved arms[L] the upper part of the main
body with a nylon washer[Q] using the set screws[M].
16) Take the lower body[P] and place on top of the lower
part of the curved arms with four (4) nylon washers[Q]
using the set screws[M].
17) Take the trim cover[K] and place onto the boom of the
installed lower body and hold in place with the nial[R].
18) Install the recommended bulbs (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain Link
[I] Chain
[J] Large Loop
[K] Trim Cover
[L] Curved Arms
[M] Set Screws
[N] Strap
Mounting
Screws
[O] Main Body
[P] Lower Body
[Q] Nylon Washer
[R] Finial
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take the main body[O] and place one of the trim
covers[K] on top of the main body as shown.
2) Take the large loop[J] and run the wires through its
center and thread onto the installed trim cover.
3) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
4) Run another hexnut down threaded pipe almost touching
rst hexnut. Now screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
5) Connect mounng strap[D] to outlet box using the strap
mounng screws[N].
Installaon Instrucons (connued)
E
D
C
N
A
G
B
F
I
H
H
J
K
L
M
O
P
Q
K
R
M
Q
Page is loading ...
/
