• Thispowersupplyisforusewithlandscapelightingsystemsonly.

• Donotsubmergetransformer.

• Thisdeviceisacceptedasacomponentofalandscapelightingsystem

 wherethesuitabilityofthecombinationshallbedeterminedbyCSAor

 localauthoritieshavingjurisdiction.TocomplywithCSArequirement,this

 xtureshouldbeinstalledbyaqualiedelectrician.AuCanada.Pourêtre

 enaccordavecIES1015CSA.Celuminairedoitêtreinstalléparun

 électricienqualié.

• WARNING:Riskofelectricshock,useonlywithlowvoltagelandscape

• Transformershouldbemountedclosetopowersupply.Extensioncords

 shouldnotbeusedwiththisunit.

• WARNING:(forPowerSupplyCordconnectedPOWERUNIT)

 RISK OF ELECTRIC SHOCK.Installpowerunit5feet(1.5m)ormore

 fromthepool,spa,orfountainwherethepowerunitisinstalled(a)

 indoorwithin10feet(3.0m)ofapool,spa,orfountain,or(b)outdoor,

 connectpowertounittoareceptacleprotectedbyaGFCI.

• Thisoutdoorpowerunitshallbeconnectedtoa115/120voltcoveredGFCI

 receptaclemarked“WetLocation”whileinuse.

• Mounttherain-tighttransformeratleastonefootabovegroundlevelwith

®

landscapedistributor.

 •8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.

 •10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.

 •12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’

  (76M),15502-BK;500’(152M),15505-BK;and1000’(304M),15506-BK.

• FindingTransformerLoad:Lowvoltagesystemsrequiretheuseofa

 transformertoreducestandard120-VOLTpowerfromyourhometo

 12-VOLTS.Todeterminethetransformersizeyouwillneed,addupthe

 wattagesofalllampsyouplantouse.Selectatransformerthatmatches

 transformer.

ThisinstructionsheetcoverstheinstallationofthefollowingKichler®Transformers:15515AZT,15M100AZT.Readtheseinstructionscarefully

beforeinstallingthisunit.

1) Determinedesiredlocationformountingtransformer.NOTE:When

 decidinglocationformountingconsiderationshouldbetakenforthe

 requirementslistedabove.

2) Markpositionoftopportionofthekeyholeslotlocationattopof

 transformerandtheslotlocatedatbottom.

3) Ifmountingtoasolidsurfacesuchaswood,siding,etc;

  A) Drill1/8”diameterpilotholesatpositionsmarkedinStep2.

 toslidedown,makingsurebottomslotisbehindheadofbottomscrew.

5) Tightenscrewsuntiltransformerissecure.

6) Split12/2.10/2,or8/2cableapproximately3”,andstrip1/2”insulation

 offeachwire.12/2.10/2,and8/2cableistheheavyblackcablewhich

 allKichler

®

12-voltlowvoltagelightingxtureswillbeconnected.

 (Referenceabovefordescriptionandpartnumbers).

7) Pushonebarewireineachoftheholesonthebottomsideoftheterminal

 blockandtightenscrewsonthefaceoftheterminalblockuntilwiresare

 secure.

(SECONDARYSIDE-12VOLTSIDE)

• Circuitbreakerwilltripifthereisashortoriftotal

 wattageinstalledexceedsratedwattagepercircuit.

•Toresetbreaker,ipswitchto‘OFF’thenbackto

 ‘ON’position.

• Iftheunitcyclesonandoffwithoutregardtothe

 timersetting,itshouldbecheckedbyaqualied

 serviceperson.

erly installed and failed under normal operating conditions, provided it is returned to the point of purchase, Where it Will be repaired or, as it may be

determined, to replace the transformer.