Dunlop M108S User manual

Dunlop
Brand
Dunlop
Model
M108S
Category
TV signal amplifiers
Type
User manual

Dunlop M108S is a ten-band graphic EQ pedal that gives guitarists and bassists a powerful tool for shaping their sound. With ten carefully chosen frequencies and both input and output level controls, the M108S lets you dial in the perfect sound for any room or situation. The pedal also features a gain slider for boosting the overall output level, and a true bypass switch for preserving your signal when the pedal is off.

Here are some of the possible use cases for the Dunlop M108S:

  • Correcting for room acoustics: The M108S can be used to correct for the акустика помещенияproblems of a room. For example, if a room is too bright, you can use the M108S to cut the high frequencies.

Dunlop M108S is a ten-band graphic EQ pedal that gives guitarists and bassists a powerful tool for shaping their sound. With ten carefully chosen frequencies and both input and output level controls, the M108S lets you dial in the perfect sound for any room or situation. The pedal also features a gain slider for boosting the overall output level, and a true bypass switch for preserving your signal when the pedal is off.

Here are some of the possible use cases for the Dunlop M108S:

  • Correcting for room acoustics: The M108S can be used to correct for the акустика помещенияproblems of a room. For example, if a room is too bright, you can use the M108S to cut the high frequencies.
92503020568REVC
M108S TEN BAND GRAPHIC EQ
M108S TEN BAND EQ
DIRECTIONS
• Run a cable from your guitar to
the M108S’s INPUT jack and run
another cable from the M108S’s
OUTPUT 1 jack to your amplifier.
Optional: Connect a separate
signal chain from the OUTPUT 2
jack to a second amplifier.
• Set all sliders to their 0dB
position and depress the
footswitch to turn the pedal on.
• Move the VOLUME slider up to
increase overall effect volume or
down to decrease it.
• Move the GAIN slider up to
increase gain or down to
decrease it.
• Move PARAGRAPHIC sliders
up to boost or down to cut
associated frequency by up
to ±12dB.
POWER
The Ten Band EQ is powered by
an 18-volt AC adapter such as the
included Dunlop ECB004 or
the DC Brick
™
and Iso-Brick
™
power supplies.
DUNLOP MANUFACTURING, INC.
P.O. BOX 846 BENICIA, CA 94510 U.S.A.
TEL: 1-707-745 -272 2 FA X: 1-707-74 5-265 8
The MXR Ten Band Graphic EQ gives players
huge amounts of tone shaping and level control
in a bullet-proof enclosure. This pedal has
been upgraded with noise-reduction circuitry,
true bypass switching, a lightweight aluminum
housing, and a second output so you can run two
separate signal chains. With ten carefully chosen
frequencies and both input and output level
controls, the Ten Band EQ will let you tune your
bass or guitar rig to any room in seconds.
SPECIFICATIONS
Input Impedance 470 kΩ
Output Impedance 5 kΩ
Max Input Level
All Sliders at 0 dB
+14 dBV
at 1 kHz
Max Output Level
All Sliders at 0 dB
+14 dBV
at 1 kHz
Frequency
Response
±1 dB, 20 Hz
to 20 kHz
Noise Floor* -101.4dBv
Filtering ±12db at:
31.25, 62.5, 125,
50, 500, 1k, 2k,
4k, 8kHz
±12dB shelf
at 16kHz
Bypass True Hardwire
Power Supply 18 Volts DC
Current Draw 48 mA
*A-weighted at 5.2Vrms
+12
0
+12
+6
-6
-12
0
+6
-6
-12
+12
+6
-6
-12
0
GAIN16K8K4K2K1K50025012562.531.2 5VOL
INPOWEROUT 2OUT 1
CONTROLS
1 VOLUME slider controls
overall effect volume
2 EQ sliders boost or attenuate
up to ±18dB at six different
frequency centers
3 GAIN slider controls amount
of gain boost
4 FOOTSWITCH toggles effect
on/bypass ( blue slider LEDs
indicate on)
1 32
4
  • Page 1 1
  • Page 2 2

Dunlop M108S User manual

Dunlop
Brand
Dunlop
Model
M108S
Category
TV signal amplifiers
Type
User manual

Dunlop M108S is a ten-band graphic EQ pedal that gives guitarists and bassists a powerful tool for shaping their sound. With ten carefully chosen frequencies and both input and output level controls, the M108S lets you dial in the perfect sound for any room or situation. The pedal also features a gain slider for boosting the overall output level, and a true bypass switch for preserving your signal when the pedal is off.

Here are some of the possible use cases for the Dunlop M108S:

  • Correcting for room acoustics: The M108S can be used to correct for the акустика помещенияproblems of a room. For example, if a room is too bright, you can use the M108S to cut the high frequencies.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents