Digital Watchdog DWC-P220CMW User guide

Brand
Digital Watchdog
Model
DWC-P220CMW
Category
Signal cables
Type
User guide

This manual is also suitable for

DWC-P220CMW
Ceiling mounting bracket for white analog PTZ cameras
Quick Start Guide
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours: 9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results
for applicable part numbers will populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
WHAT’S IN THE BOX
1x Teflon tape 2x set screws, no head (M5x5)
4x O-ring 2x machine screws, BH (UNC #8-32 8L)
1x hex Allen wrench (2.5) 4x machine screws, PH (M6x9)
3x plastic anchors (6pi) 7x machine screws, PH (M6x12)
3x tapping screws, PH (6x35) 1x quick setup guide
A. Attach the mount base ( ) and plate ( ) to the mounting surface using the supplied M6 tapping
screws ( ) and plastic bushings ( ).
B. Wind Teflon tape around both threaded ends of the pipe (about 20 times) for sealing. If necessary,
use a silicone rubber sealant to seal the area where the mount base and the pipe meet.
C. Fit the pipe (of which threads are covered by Teflon tape) into the mount base ( ) and turn until
it is securely fastened.
D. Pull all the required cables through the mount base ( ) and pipe ( ).
E. Align the dome adaptor ( ) with the pipe and turn until it is securely fastened.
F. Fasten the mount base ( ), dome adaptor ( ) using the set screw.
G. Fasten the vandal proof dome housing to the dome adaptor ( ) using M6 x 12 machine screw.
INSTALLING THE MOUNTING ACCESSORY
Rev Date: 01/20
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Quick Start Guide
5
6
6
6
6
1
1
1
1
4
3
2
Installation with a junction box
1
4
3
2
Cable
Installation without a junction box
1
2
Cable
Junction Box
5
1
MOUNTING THE CAMERA TO THE MOUNTING ACCESSORY
USING A JUNCTION BOX OR MOUNTING PLATE
CABLING THE CAMERA
Dimensions Inches (mm)
1. Cable passing through the wall 2. Cable on the wall (Remove the
conduit knockout for cable
passing through)
3. Cable passing through
the wall with the
junction box (Attention
to the plate side)
Cable
Mount
Base
Plate
Cable
Junction
Box
Mount
Base
Plate
Cable
Mount
Base
Plate
Knockout
Seal around the mount base
tightly using silicon rubber
1.92"
(49mm)
15"
(381mm)
11.41"
(290mm)
1.65"
(42mm)
0.25"
(6.5mm)
49
4.19"
(106.5mm)
4.88"
(124mm)
(Mount base size)
PF 1” TAP
120°
CEILING
1.92"
(49mm)
15"
(381mm)
11.41"
(290mm)
1.65"
(42mm)
0.25"
(6.5mm)
49
4.19"
(106.5mm)
4.88"
(124mm)
(Mount base size)
PF 1” TAP
120°
CEILING
  • Page 1 1
  • Page 2 2

Digital Watchdog DWC-P220CMW User guide

Brand
Digital Watchdog
Model
DWC-P220CMW
Category
Signal cables
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents