Vivo DESK-V303G Assembly Instructions

Brand: Vivo

Model: DESK-V303G

Type: Assembly Instructions

Gray Kids’ Height Adjustable Desk and Chair

Instruction Manual

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

https://vivo-us.com/products/desk-v303g

SKU: DESK-V303G

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

If you do not understand these directions, or if you have any doubts about the safety of the installation,

please call a qualified technician. Check carefully to make sure there are no missing or defective parts.

Improper installation may cause damage or serious injury. Do not use this product for any purpose that is

not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage

or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING!

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF DESK OR CHAIR

• USE TIPOVER RESTRAINT OR ANCHOR DESK TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

PACKAGE CONTENTS

B1 (x1)

Chair Leg

B2 (x4)

Feet

B4 (x1)

Side Support Bar

B5 (x1)

Center Support

Bar

B6 (x1)

Seat Bottom

B3 (x1)

Support Bar

B8 (x1)

Desktop

B9 (x1)

Desk Leg

B10 (x1)

LED Lamp

B7 (x1)

Seat Back

A1 (x8)

Lock Washer

A3 (x8)

Plastic Washer

A4 (x4)

ST4.8x25 Screw

A5 (x2)

Knob

A2 (x12)

M6x20

A6 (x4)

M6x45

A8 (x1)

Allen Wrench

A7 (x1)

Hook

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

TOOLS NEEDED

Phillips

Screwdriver

ASSEMBLY STEPS

STEP 1

Adjust sides of chair legs (B1) to equal length.

Place chair legs in feet (B2), making sure legs

are fully seated in openings.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

165lbs

(75kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

220lbs

(100kg)

DESK

CHAIR

STEP 2

Secure feet using x4 M6x20 screws (A2) and x4

lock washers (A1). Tighten with Allen wrench

(A8).

STEP 3

Assemble right side support bar (B3) to leg

using x2 M6x20 screws (A2) and x2 plastic

washers (A3), making sure the back of the bar

faces in the same direction as the long ends of

the feet. The support bar has a large hole on

the le side which will face inward. Tighten

with Allen wrench.

STEP 4

Slide center support bar (B5) into large hole

on right side bar. Slide le side support bar

(B4) onto center bar, and secure to legs with x2

M6x20 screws (A2) and x2 plastic washers (A3).

Tighten with Allen wrench.

STEP 5

Mount plastic seat bottom (B6)

to assembled chair frame using

1” screws (A4). Tighten with

Phillips screwdriver.

STEP 6

Slide plastic seat back (B7) onto chair frame,

aligning upper or lower holes in seat back with

screw holes in frame depending on the needed

height.

STEP 7

Secure seat back using knobs (A5).

STEP 8

Adjust chair feet to sit level if needed.

STEP 9

Adjust sides of desk legs (B9) to equal length. Place desk legs in

feet (B2), making sure legs are fully seated in openings.

STEP 10

Secure feet using x4 M6x20 screws (A2) and x4 lock

washers (A1). Tighten with Allen wrench (A8).

STEP 11

Assemble desktop (B8) to legs using M6x45 screws (A6) and

x4 plastic washers (A3), making sure the front of the desktop

faces in the same direction as the long ends of the feet.

Tighten with Allen wrench.

STEP 12

Squeeze sides of hook (A7) and fit into slot on le or right side of desk.

STEP 13

Adjust desk feet to sit level if needed. Place lamp (B10) into le side hole in desktop. Connect power

adapter to lamp and plug into wall outlet.

STEP 14

Loosen knobs on sides of desk to adjust desktop tilt angle, and tighten knobs to secure position.

CAUTION: Do not grip the back of the desktop when adjusting tilt angle. Grip sides of desktop for

safer adjustment.

Lamp Operation: Touch power

button to turn lamp on. Touch

button again repeatedly to

change brightness (low, medium,

high). To turn lamp o, hold

power button.

Height Adjustment

RAISE:

Step on the support bar with one foot and pull up with even motion on both sides of the desk, until it

reaches desired height. Repeat with chair.

LOWER:

Step on the support bar with one foot and pull up with even motion on both sides of the desk, until it

reaches max height. Slowly lower down to desired height. Repeat with chair.

To avoid injury due to

falling, do not lean the

chair backwards or to

the sides while sitting.

Remove large or unstable

objects before tilting the

desktop.

CAUTION!

Failure to follow these instructions may result in property damage and/or personal injury.

LAST UPDATED: 09/21/2020

REV1

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo DESK-V303G Assembly Instructions

Vivo DESK-V303G Assembly Instructions

Vivo DESK-V303G Assembly Instructions

Related papers

Other documents