USER MANUAL
CarPlay/Android Auto Car Stereo
LEADFAN
LEADFAN
- 1 -
BEFORE INSTALLATION
Thank you very much for purchasing and using our products, when
you receive the product, please do not take the product directly to the
car for installation, because the product is in the after a long journey
it may affect the product. Please try the machine before installing.
Test method: Take the machine to the battery of the car and test it.
This car stereo applies to a power supply voltage at 12V DC, connect the
red and yellow wire of the power cord together and connect it to the
positive pole of the battery. The black wire of the power cord is connected
to the negative pole of the battery. Wait for 10 seconds after connecting,
press each button of the machine to see if the machine can boot normally.
If it can be turned on, it means there is no problem, you can install it. If
the test machine can not start normally, confirm that you follow the steps
of our test method in strict accordance with the operation. If the problem
is still not solved, please contact us.
Attentions:
*Do not drop the metal objects into the radio.
*If there is smoke or smell on the radio, turn off the power at once.
*Do not make the radio fall or have a strong collision.
*Do not install the radio in place of strong sunlight, high temperature,
high humidity or dusty.
*Replace the fuse with the same specification. If you are using a different
one, it may cause failure of the radio.
*In order to prevent short circuit, please pull out the power wire when you
replace the fuse.
*Do not get the radio wet when washing your car. This may cause a short
circuit, fire or other failure.
LEADFAN
LEADFAN
- 2 -
INSTALLTION
Note: Please connect the wires as instruction show, otherwise the
machine can’t be turned on or occur some other problems. If the yellow
line is connected to the wrong place, the radio will still be turned on, but
the memory will be erased every time you turn it off.
LEADFAN
LEADFAN
- 3 -
INSTALLTION
LEADFAN
LEADFAN
- 4 -
MAIN INTERFACE
LEADFAN
LEADFAN
- 5 -
1. HOME: Display the top menu screen.
2. Volume: Adjust the volume, from 0 to 40.
3. Light: Turn on, dim the light and turn off.
4. Return: Return to the previous screen.
5. Time Display: You can click here to set the time
6. Currently Used Mode:Can switch/pause
7. Radio: Enter the radio mode to listen to the radio station.
8. BT: Enter the Bluetooth call interface.
9. Setup: Enter the system setting interface.
10. USB: Plug your USB driver to the port, then touch the USB icon to
enter the USB playback mode.
11. SD: Insert Micro SD to the port, it can play Music/Video/ Pictures
from the card
12. Phonelink: CarPlay/Android Auto and mirrorlink function. Inserting
the data cable uses the mirrorlink function by default. Click ‘Phonelink’ to
switch to CarPlay/Android Auto function supports voice control.
13. AV in: Enter the AV IN external audio mode interface.
14. Wallpaper Settings
LEADFAN
LEADFAN
- 6 -
RADIO
1The area of the stored station. Can store stations. When you need
to listen to a certain fixed station, just click it.
2/3 Press to search for radio stations, short press will step 0.05MHz,
long press will change automatically.
4 Switch band FM1-FM2-FM3.
5Automatically search for radio stations in the full frequency band
and store them.
6 Long-range/short-range broadcast.
7Mono / Stereo switch.
8 Automatically browse each station for 5 seconds.
LEADFAN
LEADFAN
- 7 -
MUSIC
PHOTO
LEADFAN
LEADFAN
- 8 -
BLUETOOTH
1 Make a call
2 Contact Book
3 Call record
4 Bluetooth music
5 Bluetooth pairing
6 Previous son
g
7 Pla
y
/Pause
8 Next song
Device name : ‘CAR KIT’ PIN: ‘0000’
Connecting Method:
1.Turn on the car stereo and make it discoverable
2.On your phone, tap settings-Bluetooth, choose the device name to pair it
LEADFAN
LEADFAN
- 9 -
SETTING
1 Settin
g
2 Sound effect settin
g
3 Bri
g
htness ad
j
ustment
4 Time setting
5 Wall
p
a
p
er
6 Steering wheel control
Language: English/Chinese/Spanish/Portuguese/Russian/Italian /German/
French/ Turkish/ Czech/ Thai/ Polish
Beep: On/Off
Key Light: You can change the LED Light to seven colors,
White/Purple/Cyan/Yellow/Red/Blue/Green or auto.
Reversing Mtue: On/Off
LEADFAN
LEADFAN
- 10 -
Phonelink
1 Phone link for Android
2 Android Auto
3 Phone link for iPhone
4 Apple CarPlay
NOTE:
Phone link for iPhone: When the phone pops up a dialog box: Trust
This Computer? Select Trust to enter the interconnect mode.
Phone link for Android: Find "Developer options", and click Go to
find "USB debugging" and turn this feature on.
CarPlay/Android Auto and mirrorlink function. Inserting the data cable
uses the mirrorlink function by default. Click ‘Phonelink’ to switch to
CarPlay/Android Auto function supports voice control.
LEADFAN
LEADFAN
- 11 -
Apple CarPlay
1. Connect the iPhone and the machine with a USB original data cable.
2. Then the machine will automatically enter the CarPlay interface.
3. After exiting,can press Phonelink on the homepage to enter the CarPlay
Android Auto
1. Download and install ‘Android auto’ software in ‘Google Play’.
2. A mobile phone with Android 5.0 or higher. Must use a valid data cable
connection.
3. Open the Android auto software on the phone.
4.After the connection is successful, you can use the functions provided by
Android auto.
LEADFAN
LEADFAN
- 12 -
Remote Controller
NOTE: Battery is not included, please insert one before use.
Reversing Camera
LEADFAN
LEADFAN
- 13 -
BASIC PARAMETERS
UNIT INSTALLATION SIZE
Operating Voltage
DC12V
Maximum Current 15A
Operating Temperature 14 ~ +140°F / -10 ~ +60°C
Screen Size 7 Inch
Screen Resolution 1024*600
Output Power 60Wx4
Bluetooth Function Version:4.0 Password:0000
Support Video Format RM/RMVB/AVI/MP4/MKV/3GP
Su
pp
ort Audio Format MP3/WMA/WAV/APE/FLAC
Support Picture Format JPG
Button Li
g
ht Colorful li
g
ht automatic / Monochrome li
g
ht o
p
tional
Radio Frequency FM 87.5~108MHz
Support media devices USB 2.0/TF card
AUX Input Front panel 3.5mm interface
Reverse Function Support (camera option)
Remote Control Infrared remote control
Language Selection
English/Chinese/Indonesian/German/Russian/Spanish
/French/Italian/Thai
Arab/Ukraine/Portugal/Czech Republic
Steering Wheel Controls Support
LEADFAN
LEADFAN
- 14 -
TROUBLESHOOTING
1 ) Unable to boot normally—Reasons for not booting
1. The yellow line should be connected to the positive pole, red line to the key control
line, black to the negative pole, less connection or wrong connection does not boot.
2. The color of the original car line may not same as the radio, if you connect according to
the color it can not be turned on.
3. The original car plug can't be plugged directly into the new unit, even if it just plugs in,
it can't be used, otherwise it won't be turned on.
4. Check if the fuse on the yellow line is broken. Twist the yellow and red wire together,
turn on the key and press the unit's power button to see if it can be turned on.
2 ) Automatic shut-down
1. The cable error connect: If the blue cable (automatic antenna power supply) is
connected to the power cable of the unit an automatic shutdown will occur. Please follow
the correct wiring method to solve the problem.
2. The voltage is unstable: Please find a 12V-5A power supply and re-tested. If it does not
automatically shut down after the test, please replace the power supply.
3 ) Having noise—The general situation of noise is caused by two reasons
1. The original speaker power is too small. When the volume of the unit is turned up,
there will be noise.
Solution: When replacing the speaker or listening to the song, the volume should not be
too large.
2. The speaker cable is grounded.
Solution: Take the iron speaker cable. Directly connected to the speaker cable of the
unit.
4 ) Remote control cannot be used—Check if the battery of the remote control has
power
Test method: Turn on the camera of the mobile phone and align the light of the remote
control, then press the button of the remote control to see if the phone will light up. If it is
not lit, there will be no power replace the battery; If it is lit, there is electricity which
proves that there is no problem with the remote control
5 ) Settings can not be saved (no memory)
1. The yellow line and the red line are connected together (connect yellow to power
supply, red to adaptive cruise control).
2. Yellow and red are reversed (just change position).
LEADFAN
LEADFAN
- 15 -
6 ) Car audio with Bluetooth but it can't work—Check the phone to see if you can
search for the unit code
Operation steps: Turn on the unit, use the phone Bluetooth search, search for CAR BT,
then click the connection, after connecting, you can answer the phone or Bluetooth to play
the song.
PIN Code: 0000 .
7 ) The radio smells and has smoke.
Smoke proves that the internal circuit has been burned. Change the insurance fuse, if it
can not solve the problem, the unit needs to be repaired.
8 ) How to adjust the sound, where is the equalizer set, the sound can not be adjusted
1. Adjust the sound: please tum the volume to adjust.
2. Equalizer settings: In general, press the volume knob to display the equalizer SEL, and
rotate the volume button to adjust each sound effect.
3.The sound cannot be adjusted: Please reset the unit or unplug the power cord and plug it
in.
9 ) No display of reversing video
Connect the wrong line or less wiring. Camera connection method：
A. The first step is to find accessories (accessory: camera + power cord + video cable)
B. The second step is to find the port of the wiring.
First find the reverse control Line on the power Line of the unit. The control line is a pink
line or brown line, connect this line to the positive pole of 12V and the screen will tum
blue.
And then find the back of the unit the CAME video input interface, find the positive and
negative of the backup light.
Third, connect the camera. There are two sockets on the camera, the red socket is
connected to the power cable, the yellow is inserted into the video cable, the red wire of
the power cable and the wire of the video cable are screwed together on the positive pole
of the reverse lamp, and the black wire of the power cable is not used, connected, the
other end of the video cable is connected to the CAME video input interface on the back
of the unit. The red line coming out of the video line is connected to the reversing control
line of the power line.
LEADFAN
LEADFAN
- 16 -
10 ) USB flash disk can not be played, the card slot does not enter the card?
Format the USB flash disk, and the file system is selected as: FAT32, re-download on or
two songs and try again. If it still doesn't work, please replace the USB flash drive.
The card slot does not enter the card: Check whether the memory card is inserted, the plug
is broken.
11 ) FM does not receive the radio station
1.The antenna plug is not fully inserted, the antenna is disconnect or the line is
disconnect.
2.Search channel hold AMS does not let go for 2 seconds The unit will automatically
search or press the up and down button to perform a channel search. Can't solve the above
2 points, Please unplug the antenna plug and find a screwdriver or a metal strip to insert it
instead of the antenna.
12 ) There is no sound right after installation
1. Check if the speaker cable is short-circuited and connected. Please reconnect if you
have any short circuit.
2. Check how many speaker cables according to the original speaker cable if there are
only 2 speaker cables to prove that the original car line does not match our unit, you need
to reroute the original car Line. One speaker must Lead to 2 speaker wires. 2 speakers
must be have 4 speaker cables to available.
13 ) There is no sound after a while
—Disconnect all the speaker cable from the unit (do not remove them), and then find an
external speaker to receive the gray and purple of the tail line of the unit.
Green any group, and then try to see if there is any sound. If there is a sound, it is proved
that the car's speaker line is short-circuited with iron or the speaker is damaged. If there is
no sound, the unit is broken.
LEADFAN
LEADFAN
/
