New England Arbors VA68890 Installation guide

Type
Installation guide

New England Arbors VA68890 is a sturdy and versatile arbor designed to enhance your outdoor space. Made from high-quality materials, it's built to withstand various weather conditions, ensuring longevity and durability. The arbor features a classic design with a trellis top, providing ample support for climbing plants and creating a beautiful focal point in your garden. It's perfect for defining pathways, creating an entryway, or adding height and dimension to your landscape.

New England Arbors VA68890 is a sturdy and versatile arbor designed to enhance your outdoor space. Made from high-quality materials, it's built to withstand various weather conditions, ensuring longevity and durability. The arbor features a classic design with a trellis top, providing ample support for climbing plants and creating a beautiful focal point in your garden. It's perfect for defining pathways, creating an entryway, or adding height and dimension to your landscape.

Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at
1 800 282 9346, ext #20
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Preassembled Arch (2)
2. Arch Rafters (6)
3.
4.
Braces (4)
5.
Preassembled Side Panels (2)
6.
Hardware
a)
c)
1 1/2” Wood Screws (12) To attach rafters to arch
Tools You Will Need
• Cordless Drill
Tape Measure
• Level
• Short Ladder
• Shovel
General Information
Read Instructions through carefully before beginning assembly.
When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
We recommend an area approx 10’x 8’ for unobstructed assembling.
You should not need to use excessive force when assembling components.
The Westwood Arbor
Please read through before starting assembly.
Ground Stakes (4)
2” Wood Screws (4) To attach braces to arbor posts
d) 3” Wood Screws (4) To attach braces to swoop top arch
b) 1 1/2” Wood Screws (8) To attach ground stakes to posts
e) 3 1/2” Wood Screws (8) To attach swoop top arches to posts
AS SE MB LY IN ST RUCTIONS
1
www.edenarbors.com
5
a
Not to Scale
b
Ver 1.1/FEB 2011
4
1
2
3
c
6
14 in
18 in
5 in
3 in
59.0 in
3 in
42 in
81.9 in
78.4 in
47 in
85.9 in
d
e
ST E P O N E
2
1
The Westwood Arbor
Connect Arch System to Side Panels
www.edenarbors.com
Lay down the side panels and arches as shown aside. Align the
notch on the underside of the arch as shown. Make sure the side
panels and arch are flush to each other.
Fasten the arches to the posts using the provided 3½” screws
(two per post).
1
2
2
ST E P T W O
3
Attach Braces and Rafters
Stand arbor upright, place and align the braces to the posts and
arches. Ensure that the faces of the posts and braces are flush to
each other. Fasten the brace to the post using the provided 2”
screws; fasten the brace to the swoop top arch using the provided
3“ screws as shown below.
Fasten the six arch rafters onto the arches using two
screws per rafter. Align to pre-drilled holes to ensure proper
spacing.
3
4
4
2” Screw
3” Screw
3
1915 Dove St., Port Huron MI USA 48060
Toll Free Phone: 1 800 282 9346 Toll Free Fax: 1 877 464 9286
www.edenarbors.com
Into Earth For Permanent Installation
STRONGLY RECOMMENDED
ST E P TH R E E
Temporary Arbor Installation
Arbors must be well secured to prevent tipping over from wind load etc.
We have provided four ground stakes for securing the arbor.
If you are installing your arbor on concrete or a wood deck, visit your
hardware store to purchase the appropriate galvanized bracketing
hardware.
Attach Ground Stakes
1
2
Permanent Arbor Installation
A
B
Fasten all four ground stakes to the base of the posts using the
provided 1 1/2” screws (2 screws per anchor) as shown aside.
For a temporary arbor installation, carefully lift the arbor and
place into final location. Push the anchors into the ground by
pushing down on the posts. Do not step on the side panel
bottom rail as the rail is not meant to carry a load. If the soil is
hard, you may need to excavate a 4 inch holes prior, or pour
some water to soften the ground.
Ensure the arbor opening is set at 42 and that the arbor is
plumb and level.
For a permanent installation, measure and dig four-8” holes, 14
deep where the ground stakes will be located. The centers of the
holes should be a rectangular pattern with dimensions of
44 1/2 x 16.
Fill excavated holes with mixed concrete and carefully lift arbor
into place. Plumb and level the arbor.
Note: The posts should not be set in the concrete.
Arbor Post
Ground Stake
Concrete
Ground
1
14 in.
35.5 cm.
  • Page 1 1
  • Page 2 2
  • Page 3 3

New England Arbors VA68890 Installation guide

Type
Installation guide

New England Arbors VA68890 is a sturdy and versatile arbor designed to enhance your outdoor space. Made from high-quality materials, it's built to withstand various weather conditions, ensuring longevity and durability. The arbor features a classic design with a trellis top, providing ample support for climbing plants and creating a beautiful focal point in your garden. It's perfect for defining pathways, creating an entryway, or adding height and dimension to your landscape.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI