P/N 3100424 ISSUE 1 © 2002
PAGE 1
CHESHIRE, CT 203-699-3000 FAX 203-699-3365 (CUST. SERV.) 203-699-3078 (TECH. SERV.)
Installation Instructions for Catalog Series 100SB
Pathfinder
TM
Sealed Beam Rotating Lights
Description and OperationDescription and Operation
Description and OperationDescription and Operation
Description and Operation
Edwards catalog series 100SB Pathfinder signals are AC
operated sealed beam rotating lights. The signals are con-
duit mounted and are suitable for use in either indoor or
outdoor (weatherproof) applications.
Electrical SpecificationsElectrical Specifications
Electrical SpecificationsElectrical Specifications
Electrical Specifications
MaintenanceMaintenance
MaintenanceMaintenance
Maintenance
Cat. Number Input Power Current
100SB*-N5 110V AC 60 Hz 0.88A
120V AC 60 Hz 1.04A
125V AC 60 Hz 1.14A
*The letter in this position of the catalog number signifies the color of
the supplied dome: A - amber, B - blue, C - clear, G - green, or R - red.
CAUTIONCAUTION
CAUTIONCAUTION
CAUTION
To avoid injury, prior to disassembly, disconnect power from
the unit.
InstallationInstallation
InstallationInstallation
Installation
CAUTIONSCAUTIONS
CAUTIONSCAUTIONS
CAUTIONS
Do not apply power to the unit until installation is
completed and cover is secured.
When installing indoors, the signal may be mounted with
the dome facing either directly up or down. For outdoor
installation, the signal must be installed with the dome
facing directly up.
Conduit Mounting
1. Route the 18" wiring leads from the 100SB through a
3/4" NPT conduit (not supplied) into a junction box.
See Figure 1.
2. Connect the green ground wire to earth ground.
Connect the black wire lead to the positive (+) power
source lead and connect the white wire lead to neutral
power source lead using wire nuts (not supplied).
3. Apply power and ensure unit operates properly.
Lamp Replacement
1. See Figure 1. Remove the screw in the clamp ring,
remove the ring and lift off the dome.
2. Replace the appropriate lamp with a GE-4416-1 PAR
36 lamp.
3. Replace the dome and secure with the clamp ring and
screw removed in step 1.
4. Apply power and ensure unit operates properly.
Cleaning
Abrasive materials or cleaners must not be used to clean
the dome.
The signal's dome should be periodically cleaned to main-
tain optimum light visibility. The dome may b e cleaned
with a soft cloth or sponge using a mild detergent. Dry
the dome thoroughly before replacing.
CAUTIONCAUTION
CAUTIONCAUTION
CAUTION
Table 1. Replacement Parts
Cat. Number Description
Replacement Domes
100SB-LA Amber
100SB-LB Blue
100SB-LC Clear
100SB-LG Green
100SB-LR Red
Replacement Lamp
GE-4416-1 PAR 36 Replacement Lamp
Contacting Edwards:
Phone: (203) 699-3000
E-Mail: [email protected]
Website: http://www.edwards-signals.com
P/N 3100424 ISSUE 1 PAGE 2
Figure 1. Catalog Series 100SB Pathfinder
Junction Box (not supplied)
Wiring (Black to positive (+),
white to neutral and green
to ground). Wire nuts not supplied.
3/4" Conduit (not supplied)
PVC Base
Clamp Ring
Dome
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
EDWARDS 108 Series Installation guide
-
-
-
-
-
-
-
-
-