Heat & Glo North Star User manual

4-03 1 480-1081

WARNING!

Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage, bodily injury or even death. Please read entire manual before you install and use

your replace.

O-T L

Tested and

Listed by

Beaverton

Oregon USA

OMNI-Test Laboratories, Inc.

C

Hearth & Home Technologies

20802 Kensington Blvd.

Lakeville, MN 55044

Division, HON INDUSTRIES

www.heatnglo.com

SAVE THESE INSTRUCTIONS

NORTH STAR

EPA CERTIFIED

WOODBURNING FIREPLACE

INSTALLATION & OPERATING INSTRUCTIONS

480-1081 2 4-03

North Star

EPA Certied Fireplace

SAFETY PRECAUTIONS

1. Please read these installation instructions completely before

beginning installation procedures. Failure to follow them could

cause a replace malfunction resulting in serious injury and/or

property damage.

2. Contact local building or re ofcials or authorized authority

about restrictions, installation inspection and permit require-

ments in your area. The replace installation must comply with

all local, regional, state and national codes and regulations.

3. An adequate supply of replacement combustion air from

outside the house must be available to the re for the replace

to operate properly.

In the event of negative pressure in the home when running

several appliances simultaneously caused by an unusually

tightly sealed home, the combustion air kit supplied with

your replace may not provide all the air required to support

combustion. Hearth & Home Technologies is not responsible

for any smoking or related problems that may result from the

lack of adequate combustion air. It is the responsibility of the

builder/contractor to ensure that adequate combustion air has

been provided for the replace.

4. This fireplace must be installed with the HTI SL Series

Chimney System.

The chimney system must always terminate outside the

building. Be sure to follow all chimney specications given in

these installation instructions.

5. NEVER leave children unattended when there is a re burning

in the replace.

6. This woodburning replace is built for solid wood fuel only.

NEVER use gasoline, gasoline type lantern fuel, kerosene,

charcoal lighter uid, or similar liquids in this replace. Keep

any flammable liquids a safe distance from the fireplace

while it is in use.

7.

DO NOT use chimney cleaners or ame colorants in your replace.

8. While servicing this replace, always shut off any electricity

to the fireplace. This will prevent possible electric shock.

Also, make sure the replace is completely cooled before

.......Installation and Draft Considerations ...................4

A. Listings and Code Approvals............................... 3

B. Description of the Fireplace System ................... 3

C. Fireplace Dimesions, Clearances & Outside Air . 5

D. Chimney Components......................................... 6

E. Pre-Installation Preparation................................. 9

F. Chimney Requirements..................................... 10

G. Installation of Fireplace ..................................... 13

H. Constructing a Chase........................................ 19

I. Operating Instructions ....................................... 21

J. Maintenance Instructions .................................. 27

Exploded View................................................... 32

Replacement Parts............................................ 33

Index ................................................................. 34

Warranty............................................................ 35

CAUTION:

Do not expose the replace to the elements (i.e. rain, etc.)

and keep the replace dry at all times. Wet insulation will

produce an odor when the replace is used.

servicing.

9. To ensure a safe replace system and to prevent the build

up of soot and creosote, inspect and clean the replace and

chimney prior to use and periodically during the burning

season. See page 27 for cleaning instructions.

10. DO NOT BURN GARBAGE OR FLAMMABLE FUIDS SUCH

AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not burn

treated wood, or wood with salt (driftwood, etc.) Burning

materials other than wood (including charcoal) under adverse

conditions may generate carbon monoxide in the home,

resulting inillness or possible death.

11. Do not connect this unit to a chimney ue already serving

another appliance.

12. Comply with all minimum clearances to combustibles as

shown in this manual for this appliance.

13. Build re on brick rebox oor. Do not use grates, andirons or

other methods to support fuel.

14. For further information refer to NFPA 211 (US) or

CAN/CSA-B365 (Canada).

WARNING!

D

o not operate without fully assembling all components.

WARNING!

Burning wet unseasoned wood can cause excessive

creosote accumulation. When ignited it can cause

a chimney re that may result in a serious house

re.

WARNING!

Do not store wood within fireplace installation

clearances or within the space required for re-fueling

and ash removal.

WARNING!

HOT WHILE IN OPERATION AND WHEN COOLING

DOWN, DO NOT TOUCH. SEVERE BURNS MAY

RESULT. KEEP CHILDREN AWAY. KEEP COMBUSTI-

BLE MATERIALS AND LIQUIDS HAVING FLAMMABLE

VAPORS AWAY. A SAFETY BARRIER SHOULD BE

INSTALLED IF CHILDREN ARE PRESENT.

TABLE OF CONTENTS

4-03 3 480-1081

North Star

EPA Certied Fireplace

WARNING!

This replace and its components are designed to be

installed and operated as a system. Any alteration to

or substitution for items in this system, unless allowed

by these installation instructions, will void the OMNI

Test Laboratories, Inc., listing and may void the product

warranty. It may also create a hazardous installation. Read

through these instructions thoroughly before starting

your installation and follow them carefully throughout

your project.

1. The replace system consists of the following:

a. Fireplace

b. Firebrick

c. Chimney Termination Cap

d. Chimney System

e. Hearth Extension

f. Outside Air

2. Required Components Include:

a. Chimney Air Kit

3. Optional Components Include:

a. Fire Screen

b. Lintel Bar

c. Heat Zone Kit

NOTE: Illustrations used throughout these instructions

reect “typical installations” and are for design purposes

only. Actual installation may vary slightly due to individual

design preferences. However, minimum clearances must

be maintained at all times.

The illustrations and diagrams used throughout these

installation instructions are not drawn to scale.

Figure 3A - Typical Fireplace System

B. DESCRIPTION OF THE FIREPLACE

SYSTEM

A. LISTINGS AND CODE APPROVALS

This fireplace system has been tested and listed in

accordance with UL127 and ULC-S610-M87 standards,

and has been listed by OMNI Test Laboratories, Inc., for

installation and operation in the United States and Canada

as described in this manual. The North Star Fireplace is

approved for mobile home installations when not installed in

a sleeping room and when an outside combustion air inlet

is provided. The structural integrity of the mobile home oor,

ceiling, and walls must be maintained. The replace must be

properly grounded to the frame of the mobile home. Outside

Air must be installed in a mobile home installation.

This replace has been tested and listed for use with the

SL-300 Series chimney and replace components listed

on page 7.

Check with your local building code agency before you begin

your installation to ensure compliance with local codes,

including the need for permits and follow-up inspections. Be

sure local building codes do not supersede UL specications

and always obtain a building permit so that insurance

protection benets cannot be unexpectedly cancelled.

If you need assistance during installation, please contact

your local dealer. For the number of your nearest Heat-N-Glo

dealer, please call 1-888-427-3973.

Heat-N-Glo® is a registered trademark of Hearth & Home

Technologies, Division of HON INDUSTRIES.

480-1081 4 4-03

North Star

EPA Certied Fireplace

INSTALLATION AND DRAFT CONSIDERATIONS

The North Star Fireplace requires a minimum ue draft of -0.10 inches of water column on High, and -0.04 inches

of water column on Low, as measured with a draft meter. Most dealers have draft meters available to measure your

ue draft if you suspect a problem.

If the re is difcult to start, and smoke spills out of the door, or you nd it hard to establish and maintain a moderately high

burn rate, then the ue draft is too low and corrective measures must be taken.

OUTSIDE AIR KIT INSTALLATION

Recommended

Location

Marginal

Location

Not

Recommended

Location

Location NOT

Recommended

Cathedral Ceiling Construction

2nd Floor

Balcony

1st Floor

Multi-level Roofs

The outside air kit is installed on the right hand side of the replace.

NOTE: A control knob allows you control of the outside air inlet.

Use of outside air for combustion is required to conserve heated

air within the structure and to provide make up air to keep the

replace venting properly.

1.

Cut a 6” hole in outside wall to accommodate outside air

piping.

2. Use 6” metal ex or rigid piping (not supplied) to directly

connect outside air to fireplace intake. Secure with hose

clamp.

3. Use the supplied termination cap with a rodent screen.

4. Seal between the wall and the pipe with silicone to prevent

moisture penetration.

IMPORTANT!! OUTSIDE AIR MUST BE IN OPEN POSITION TO OPERATE FIREPLACE PROPERLY

4-03 5 480-1081

North Star

EPA Certied Fireplace

C. FIREPLACE DIMENSIONS

23-1/8"

11-1/8"

9-11/16"

6-1/2"

5-7/8"

1"

Fan Electrical Access,

(right side of fireplace)

See Page 10

TOP VIEW

FRONT VIEW

SIDE VIEW

MINIMUM CLEARANCES TO COMBUSTIBLES

NONCOMBUSTIBLE

DECORATIVE MATERIAL

(2) HX4 MICORE FACTORY

BUILT HEARTH EXTENSION

(Each HX4 = 1/2" (13mm) thick)

HEARTH METAL STRIPS

GAP (SEAL WITH NONCOMBUSTIBLE SEALANT)

UP TO BOTTOM OF FASCIA

6" (152mm)

1" (51mm)

40-5/16"

31-1/8

"

37"

3-1/2"

40"

43-13/16"

Figure 5A - Factory Built Hearth Extension

WITHIN ENCLOSURE AREA:

Appliance to backwall 1” (25mm)

Appliance to sidewall 1” (25mm)

Duct boots to framing 0” (0mm)

Top standoffs to header 0” (0mm”)

EXPOSED SURFACES

Faceplate to sidewall 16” (406mm)

Heat Zone air grills to ceiling 12”(305mm)

HEARTH EXTENSION / FLOOR PROTECTION

1. Fireplace and Hearth Extension are ush on the oor:

Combustible ooring 20” (508mm) in front of and 8” (203mm) to either side of the fuel opening; must be insulated with

non-combustible oor protection with a minimum thickness of 1” (25mm) and (“k” value = 0.43).

2. Fireplace is ush on the oor and Hearth Extension is raised to the bottom of the fascia:

Raised hearth must be constructed of non-combustible materials such as cement block or equivalent material Decorative

combustible ooring on the raised hearth must be 20” (508mm) in front of and 8” (203mm) to either side of the fuel

opening must be insulated with non-combustible floor protection with a minimum thickness of 1-1/2” (38mm) and

(“k” value = 0.43).

3. Fireplace is recessed in the oor to the bottom of the fascia:

Combustible ooring 30” (762mm) in front of and 8” (203mm) to either side of the fuel opening ;must be insulated with

non-combustible oor protection with a minimum thickness of 1” (25mm) and (“k” value = 0.43).

MANTEL

Mantel from base of replace 60” (1524mm)

Maximum mantel width 12” (305mm

CHIMNEY SECTIONS

Chimney sections at any level require a 2” (51mm) minimum

air space clearance between the framing and chimney

section.

480-1081 6 4-03

North Star

EPA Certied Fireplace

D. CHIMNEY COMPONENTS

The following pictures show the SL-300 Series chimney and replace components which may

be safely used with this replace.

4"

42"

ID4

INSULATED DUCT

4

"

42"

UD4

UNINSULATED DUCT

Catalog No. Description

CAK4A Chimney Air Kit

ID4 Insulated Duct/Outside Air

UD4 Uninsulated Duct/Outside Air

SL306 Chimney Section - 6” long

SL312 Chimney Section - 12” long

SL318 Chimney Section - 18” long

SL324 Chimney Section - 24” long

SL336 Chimney Seciton - 36” long

SL348 Chimney Section - 48” long

SL3 Chimney Stabilizer

SL315 Chimney Offset/Return - 15°

SL330 Chimney Offset/Return - 30°

FS338 Firestop - Straight

FS339 Firestop - 15°

FS340 Firestop - 30°

AS8 Straight Attic Insulation Shield

JB877 Chimney Joint Band

CB876 Chimney Bracket

RF370 Roof Flashing - Flat to 6/12 Pitch

RF371 Roof Flashing - 6/12 to 12/12 Pitch

TR344 Round Termination Cap

TR342 Round Telescoping Termination Cap

ST375 Square Termination Cap

TS345 Square Termination Cap

CT35 Chase Top

MH842 Mobile Home Thimble

MH841 Mobile Home Thimble Extension, 20”

HX4 MICORE Hearth Extension, 20” wide

Mesh-HHT Fire Screen

HHT-Template Metal Face Template

HeatZone-Wood Heat Zone Kit

LintelBar-HHT Lintel Bar

4-03 7 480-1081

North Star

EPA Certied Fireplace

SL3 - Chimney Stabilizer

SL315-330 - Offset/Return

RF370 - Roof Flashing

Flat to 6/12 Pitch

RF371 - Roof Flashing

6/12 to 12/12 Pitch

CB876

Chimney Bracket

AS8

Straight Attic

Insulation Shield

Chimney Sections

Firestop Spacer

24"

A

8" 101/2"

Inside

Diameter

8"

Outside

Diameter

10"

A

B

14-1/2"

10-1/2"

2"

10-1/2"

JB877

Joint Band

12"

24-5/8"

27-3/8"

12"

31"

24-5/8"

SL306 6” 4-3/4”

SL312 12” 10-3/4”

SL318 18” 16-3/4”

SL324 24” 22-3/4”

SL336 36” 34-3/4”

SL348 48” 46-3/4”

Catalog No.

A B

FS338 0° 14-1/2”

FS339 15° 18-3/8”

FS340 30° 16-3/4”

Catalog No.

A B

A = Actual Length

B = Effective length (length of

chimney part after it has been

snapped to another)

Inside

Diameter

8"

Outside

Diameter

10"

20-3/4"

480-1081 8 4-03

North Star

EPA Certied Fireplace

10-1/2"

12"

5-1/4"

4"

TR344

Round Termination Cap

TR342

Round Telescoping

Termination Cap

ST375

Square Termination Cap

CT35

Chase Top

CAK4A

Chimney Air Kit

15-3/4"

TR342

TERMINATION CAP

TOP OF

UPPERMOST

CHIMNEY

SECTION

14-1/2"

MAX.

DISTANCE

CHASE TOP

23"

14-3/4"

17-3/4"

(8" Flue)

(10-1/2" Outer)

16-1/2"

13-1/4"

22-1/4"

23-1/2"

TS345/TS345P

Square Termination Cap

72" 36"

2"

10-7/8"

24-5/8"

16-5/8"

16-5/8"29"

MH841

Mobile Home Thimble

Extension 20”

MH842

Mobile Home Thimble

4-03 9 480-1081

North Star

EPA Certied Fireplace

88-7/8"

44-7/16"

23-5/8"

62-13/16"

42"

Figure 9B

Installation Along a Wall or an Exterior Chase

Figure 9C

Corner Installation

WARNING! Do not draw outside air from garage spaces. Exhaust products of gasoline engines are hazardous.

Do not install outside air ducts such that the air may be drawn from attic spaces, basements or above the roong where

other heating appliances or fans and chimneys exhaust or utilize air. These precautions will reduce the possibility of

replace smoking or air ow reversal. The outside air inlet must remain clear of leaves, debris ice and/or snow. It must be

unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability to maintain

a re. Smoke spillage can also set off smoke alarms.

WARNING! To prevent contact with sagging or loose insulation, the replace must not be installed against vapor barriers

or exposed insulation. Localized overheating could occur and a re could result.

Figure 9A - Fireplace Locations

1. Fireplace Locations and Space Requirements

Several options are available to you when choosing a location for your replace. This replace may be used as a room divider,

installed along a wall, across a corner or used in an exterior chase. See Figure 9A.

Locating the replace in a basement, near frequently opened doors, central heat outlets or returns, or other locations of considerable

air movement can affect the performance and cause intermittent smoke spillage from the front of the replace when no outside

air is used. Outside air is required for combustion. (see page 21). The North Star Fireplace comes equipped with an outside

air inlet to feed combustion air from outside the home, along with an outside air termination cap. Consideration should be given

to these factors before deciding on a location.

CLEARANCES!

A minimum 1” air clearance must

be maintained at the back and

sides of the replace assembly.

Chimney sections at any level

require a 2” minimum air space

clearance between the framing

and chimney section.

51"

23-1/2"

10"

E. PRE-INSTALLATION PREPARATION

As a room

divider

A

long a wall

In an exterior chase or

projecting into a garage

Across a corner

These are

rough

framing

dimensions

only.

Figures 9B and 9C show two typical installations for the outside air kit. Allowances must be made for 90° bends. Less

space is required when ducting goes directly outside without forming elbows.

480-1081 10 4-03

North Star

EPA Certied Fireplace

43-7/8"

42"

2"

24"

Position mantel

60” from base of

the replace

WARNING!

Do not apply combustible nishing materials over

any part of the front of this replace or a structure

re may result. The metal replace face may only

be covered with noncombustible materials such

as ceramic tile, brick, or stone. Do not cover or

block any cooling air slots.

CLEARANCES!

A minimum 1” air clearance must be maintained at the back and sides

of the replace assembly.

Chimney sections at any level require a 2” minimum air space

clearance between the framing and chimney section.

Figure 10A- Framing the Fireplace

The North Star Fireplace will t the framed opening width of

43-7/8” tall. The nished cavity depth must be no less than 24”.

Framing must extend straight up all the way to the ceiling.

Figure 10A shows a typical framing (using 2 x 4 lumber) of the

replace, assuming combustible materials are used. All required

clearances to combustibles around the replace must be adhered

to. Any framing across the top of the replace must be above

the level of the top standoffs.

F. CHIMNEY REQUIREMENTS

When planning your fireplace location, the chimney construction and necessary clearances must be considered. The fireplace

system and chimney components have been tested to provide exibility in construction. The following gures are the minimum

distances from the base of the replace.

2. Framing the Fireplace

1. Min overall straight height 13 ft.

2. Min height with offset/return 14.5 ft.

3. Max height 50 ft.

4. Max chimney length between

an offset and return

12 ft.

5. Maximum distance between chimney stabilizers 35 ft.

6. Double offset/return minimum height 20 ft.

7.

Maximum unsupported chimney length between the offset and return

6 ft.

8.

Maximum straight unsupported chimney height above the replace

35 ft.

3. Electrical Access and Wiring Diagram

14-2 w/ground

Standard wall mount with

Junction Box

14-3 w/ground

WIRE NUT

WHITE

GREEN

BLACK

RED

WHITE

Match colors to wire

harness (red to red,

white to white, etc) and

secure with a wire nut

NOTE: The manual override switch, rheostat speed

control and cover plate are supplied. You will need to

supply: 14-3 wire with ground; 14-2 wire with ground;

standard wall mount junction box; wire nuts.

1. Remove outside air cover plate on the bottom

right side of the replace.

2. Thread the 14-3 with ground wire through the

opening with the strain relief on the cover plate.

3. Match colors to wire harness, (red to red, white

to white, etc) and secure with wire nuts.

Figure 10B- Fan Wiring Diagram

NOTE: Wiring for blowers must be done before

framed enclosure is completed. If using a

Heat Zone kit, it also must be installed before

enclosure is complete.

4-03 11 480-1081

North Star

EPA Certied Fireplace

WARNING!

Do not combine offsets to create an offset greater than 30° from vertical. This

may create a re hazard since the natural draft may be restricted.

a. To bypass any overhead obstructions, the chimney may be offset using a 15° or a 30° offset/return. Perform the following steps

to determine the correct chimney component combination for your particular installation.

b. An offset and return may be attached together or a chimney section(s) may be used between an offset and return.

1) Measure how far the chimney needs to be shifted to enable it to avoid the overhead obstacle. See Figure 11A, dimension

“A” to determine chimney sections required to achieve the needed shift.

2) After determining the offset dimension, refer to Table 1 and nd the “A” dimension closest to but not less than the

distance of shift needed for your installation.

3) The “B” dimension that coincides with the “A” dimension represents the required vertical clearance that is needed

to complete the offset and return.

4) Read across the chart and nd the number of chimney sections required and the model number of those particular

chimney parts.

5) Whenever the chimney penetrates a oor/ceiling, a restop spacer must be installed.

6) The effective height of the replace assembly is measured from the base of replace to top of starter collar.

Example: Your “A” dimension

from Figure 11A is 14-1/2”.

Using Table 1 the dimension

closest to, but not less than

14-1/2” is 14-5//8” using a 30°

offset/return. It is then deter-

mined from the table that you

would need 33” (Dimension

“B”) between the offset and

return. The chimney com-

ponents that best fit your

application are two SL312s.

A

B

1-1/4" OVERLAP

Figure 11A - Chimney Offset/

Return

*Proper assembly of air cooled chimney parts result in an overlap at

chimney joints of 1-1/4”. Effective length is built into this chart.

Table 1 Offset Chart*

1. Using Offsets and Returns

1-5/8” 13-3/8” 3-7/8” 14-1/2” - - - - - --

2-7/8” 17-3/4” 6-1/4” 18-5/8” 1 - - - - --

- - 8-5/8” 22-3/4” 2 - - - - --

4-1/2” 23-5/8” 9-1/4” 23-3/4” - 1 - - - --

- - 11-5/8” 27-7/8” 1 1 - - - --

6” 29-3/8” 12-1/4” 29” - - 1 - - --

7-1/4” 34” 14-5/8” 33” - 2 - - - --

- - 15-1/4” 34-1/8” - - 2 1 - --

- - 17-5/8” 38-1/4” 1 - - 1 - -

- - 20-5/8” 43-1/2” - - - - - --

10-5/8” 46-3/4” 21-1/4” 44-5/8” - - - - 1 -

11-7/8” 51-3/8” 23-5/8” 48-3/8” 1 - - - 1 -

- - 26-5/8” 53-7/8” - - - 2 - -

13-3/4” 58-3/8” 27-1/4” 55-3/4” - - - - - -

15” 63” 29-5/8” 59” 1 - - - - 1

16-1/2” 68-3/4” 32-5/8” 64-1/4” - 1 - - - 1

18” 74-5/8” 35-5/8” 69-1/2” - - 1 - - 1

- - 38-5/8” 74-5/8” - - - 1 - 1

- - 41” 78-3/4” 1 - - 1 - 1

22-3/4” 91-7/8” 44-5/8” 85” - - - - 1 1

24” 96-1/2” 47” 89-1/8” 1 - - - 1 1

25” 103-1/2” 50-5/8” 95-1/2” - - - - - 2

A B A B

15° 30°

SL306 SL312 SL318 SL324 SL336 SL348

480-1081 12 4-03

North Star

EPA Certied Fireplace

THEN

BUT

MUST BE AT

LEAST 2 FEET

NEVER LESS

THAN 3 FEET

I

F 10

FEET OR

LESS

Figure 12A- Chimney Height

*Dimensions reect effective height.

Table 2

2. Chimney Height Requirements (above roof

line)

a. Major building codes specify a minimum chimney

height above the roof top. These specications are

summarized in what is known as the Ten Foot Rule.

This rule states:

If the horizontal distance from the side of the

chimney to the peak of the roof is 10 feet or less, the

top of the chimney must be at least 2 feet above

the peak of the roof, but never less than 3 feet

in overall height above the highest point where it

passes through the roof.

If the horizontal distance from the side of the

chimney to the peak of the roof is more than 10 feet,

a chimney height reference point is established on

the surface of the roof a distance of 10 feet from the

side of the chimney in a horizontal plane. The top

of the chimney must be at least 2 feet above this

reference point, but never less than 3 feet in height

above the highest point where it passes through the

roof. See Figure 12A.

b. These chimney heights are necessary in the interest

of safety but do not ensure smoke-free operation.

Trees, buildings, adjoining roof lines, adverse wind

conditions, etc. may create a need for a taller

chimney should smoking occur.

3. Number of Sections Required

To determine the chimney components needed to

complete your particular installation, follow the steps

below:

a. Determine the total vertical height of the replace

installation. This dimension is measured from the

base of the replace assembly to the point where

the smoke exits the termination cap.

b. Subtract the effective height of the replace assembly

from the overall height of the replace installation

(measured from the base of the replace to the

bottom of the termination cap).

c. Refer to Table 2 to determine what components must

be selected to complete the replace installation.

d. Determine the number of restop spacers, stabiliz-

ers, roof ashing, etc. required to complete the

replace installation.

HEIGHT OF CHIMNEY COMPONENTS

Chimney Stabilizer

SL3 4-3/4”

Firestop Spacers

FS338 0”

FS339 0”

FS340 0”

Offsets/Returns

SL315 13-3/8”

SL330 14-1/2”

Roof Flashing

RF370 0

RF371 0

Chimney Sections*

SL306 4-3/4”

SL312 10-3/4”

SL318 16-3/4”

SL324 22-3/4”

SL336 34-3/4”

SL348 46-3/4”

4-03 13 480-1081

North Star

EPA Certied Fireplace

WARNING!

Before starting, do the following:

1. Wear gloves and safety glasses for protection.

2. Keep hand tools in good condition. Sharpen cutting edges and make sure tool handles are secure.

3. Always maintain the minimum air space required to the enclosure to prevent re.

G. INSTALLATION OF FIREPLACE

1" OVERLAP

Metal strips 2" under edge of

Fireplace and Hearth Extension and

2" on both side of fireplace opening

Figure 13A - Positioning the Metal Strips

1. Positioning the Fireplace

This fireplace may be placed on either a combustible or

noncombustible continuous at surface, depending on the type

of installation. Follow the instructions for framing on pages

9-10 and Hearth Extension/Floor Protection Requirements

under Minimum Clearances to Combustibles on page 5.

Slide the fireplace into position. Be sure to provide the

minimum 1” air clearance at the sides and back of the

replace assembly.

3. Leveling the Fireplace

L

evel the replace side-to-side and front-to-back. Shim with

noncombustible material, such as sheet metal, as necessary.

Secure the replace (using the pallet mounting brackets located

on either side of the replace) to the oor.

2. Placing the Protective Metal Hearth Strips

Included with your replace you will nd two metal hearth

strips measuring approximately 23” x 4”. These strips are

used to provide added protection where the replace and the

hearth extension meet.

Slide each metal strip 2” under the front edge of the replace.

The individual pieces must overlap each other by 1” minimum

in the middle of the replace to provide continuous coverage

of the oor. See Figure 13A. These metal strips should extend

from the front and sides of the replace opening by 2”.

WARNING!

Carefully follow the instructions for assembly of the

pipe and other parts needed to install this fireplace

system. Failure to do so may result in a re, especially

if combustibles are too close to the replace or chimney

and air spaces are blocked, preventing the free movement

of cooling air.

4. Assembling Chimney Sections

Attach either a straight chimney section or an offset to the top

of the replace (depending on your installation requirement).

Chimney sections are locked together by pushing downward

until the top section meets the stop bead on the lower

section.

The inner ue is placed to the inside of the ue section below

it. The outer casing is placed outside the outer casing of the

chimney section below it. See Figure 13B.

NOTE: Chimney Air Kit, Part CAK4A is required.

Follow instructions supplied with the kit.

Figure 13B-Assembling Chimney Sections

CAUTION:

Inner ue and outer liner sections cannot be disassembled

once locked together. Plan ahead to ensure the proper

installation height is achieved with the selected chimney

components.

480-1081 14 4-03

North Star

EPA Certied Fireplace

ROOM ABOVE

A

TTIC ABOVE

Figure 14A

Installing the Firestop Spacer

CAUTION:

Firestop spacers must be used whenever the

chimney penetrates a ceiling/oor area.

24"

AS8 ATTIC

INSULATION

SHIELD

FS338

FIRESTOP

SPACER

CHIMNEY

IN

SULATION

10-1/2"

14-1/2"

Figure 14B

Installing an Attic Insulation Shield

6. Attic Insulation Shield

An insulation shield should be installed when there is a

possibility of insulation coming into contact with the factory

built chimney system. The insulation shield is installed by

positioning it over the vertical chimney section where it

penetrates a restop spacer. The restop spacer will support

the insulation shield. See Figure 14B.

5. Installing Firestop Spacers

Mark and cut out an opening in the ceiling for the restop

spacer being utilized (14-1/2” x 14-1/2” for an FS338, 14-1/2”

x 18-3/8” for an FS339 and 14-1/2” x 23” for an FS340).

Frame the opening with the same dimension lumber used

in the ceiling joists.

Install the restop spacer.

These restop spacers are designed to provide the minimum

2” air space required around the chimney. In all situations, the

restop spacers are to be nailed to the ceiling joists from the

bottom or replace side, EXCEPT when the space above is

an insulated ceiling or attic space. In this situation, the restop

spacer must be nailed from the top side to prevent loose

insulation from falling into the required 2” air space around the

chimney. See Figure 14A.

7. Double-checking the Chimney Assembly

Continue assembling the chimney sections up through the

restop spacers as needed. While doing so, be aware of the

height and unsupported chimney length limitations that are

given on page 10 under “Chimney Requirements”.

Check each section by pulling up slightly from the top to

ensure proper engagement before installing the succeeding

sections. If they have been connected correctly, they will not

disengage when tested.

NOTE: Wiring for blowers must be done before

framed enclosure is completed. If using a Heat

Zone kit, it also must be installed before enclosure

is complete.

4-03 15 480-1081

North Star

EPA Certied Fireplace

1. An outside air inlet must be provided for combustion and must

remain clear of leaves, debris, ice and/or snow. It must be

unrestricted while unit is in use to prevent room air starvation

which can cause smoke spillage and an inability to maintain a

re. Smoke spillage can also set off smoke alarms.

2. The replace is to be secured to the mobile home structure.

Use same holes that attached the replace to the pallet to

secure it to the oor use 1/4” x 2” lag bolts or equivalent.

3. Unit must be grounded with #8 solid copper grounding wire or

equivalent and terminated at each end with N.E.C. approved

grounding device.

4.

Refer to Minimum Clearances to Combustibles on page 5 and

chimney components on pages 6-8.

5. Floor protections requirements on page 17 must be followed

precisely.

6. Use silicone to create an effective vapor barrier at the location

where the chimney or other component penetrates to the

exterior of the structure.

7.

Follow the chimney and chimney connector manufacturer’s

instructions when installing the ue system for use in a mobile

home.

NOTE: Top sections of chimney must be removable to allow

maximum clearance of 13.5’ (411cm) from ground level for

transportation purposes.

8. Burn wood only. Other types of fuels may generate poisonous

gases (e.g., carbon monoxide).

8. Mobile home installation

You must use the outside air termnination cap supplied

with your North Star Fireplace for installation in a

mobile home. If you use an alternative material it must

be designed to prevent material from dropping into the

area beneath the mobile home, and to prevent rodents

from enterting from the outside.

CAUTION:

The structural integrity of the mobile home oor, wall and

ceiling/roof must be maintaned. (i.e., Do not cut through

oor joist, wall stud, ceiling truss, etc.)

WARNING!

NEVER DRAW COMBUSTION AIR FROM A WALL,

FLOOR OR CEILING CAVITY OR FROM ANY

ENCLOSED SPACE SUCH AS AN ATTIC OR GARAGE.

WARNING!

DO NOT INSTALL IN SLEEPING ROOM.

9. SL-300 Series MH842 Celing/Roof Thimble

1. Locate the point where the chimney will exit the roof by

plumbing down to the center of the chimney. Lay out, cut and

frame a 14-1/2” square opening (measured on the horizontal)

through the ceiling and roof structure. See Chapter 25 of the

Uniform Building Code for Framing Details.

2. The thimble must extend completely through the roof structure

shielding combustible materials. Five location holes have been

provided to allow for a variety of ceiling/roof thicknesses. The

MH841 Thimble Extension is required when the ceiling/roof

thickness exceeds 12-1/2”. The extension should overlap

the thimble one inch.

3. To attach the extension to the thimble, drill 1/8” holes through

the outer shield of the thimble using the predrilled holes in the

extension as guides. Attach the extension to the thimble using

the screws provided with the extension.

4. Install the thimble assembly and nail it securely to the framing

members.

5. Center the ashing over the chimney and nail it to the roof

using the Stormguard nails provided. Keep gaps between the

ashing plate and the roof to a minimum.

6. Caulk the flashing plate and roof junction as well as the

vertical seam on the ashing. All nail heads must be caulked

with a roong sealant.

7. Finish assembling the chimney storm collar and termination

cap following the installation instructions provided with

them.

CHIMNEY

FLASHING

PLATE

JOISTS

NAIL

THIMBLE

FLASHING

CHIMNEY

FLASHING

PLATE

NAIL

THIMBLE

SCREW

THIMBLE

EXTENSION

Figure 15A - Installing an MH842, Conguration 1

Figure 15A - Installing an MH842, Conguration 2

480-1081 16 4-03

North Star

EPA Certied Fireplace

WARNING!

Maintain a minimum of 2” air clearance to all parts of the

chimney system at all times! Failure to maintain this 2” air

clearance will cause a structure re.

NOTE: You must provide support for the pipe during construction

and check to be sure inadvertent loading has not dislodged the

chimney section from the replace or at any chimney joint.

WARNING!

When chimney sections exceeding six feet in length

are installed between an offset and return, structural

support must be provided to reduce off-center loading

and prevent chimney sections from separating at the

chimney joints.

FIRESTOP

JOINT BAND

(OPTIONAL)

STRAPS

OPTIONAL

ADDITIONAL

SUPPORT

Figure 16B - Offset/Return with Stabilizer

10 Securing the Chimney System

When offsets and returns are joined to straight pipe sections,

they must be locked into position with the screws provided

(outer only), using the predrilled holes. To prevent gravity

from pulling the chimney sections apart, the returns and the

chimney stabilizers have straps for securing these parts to

joists or rafters. See Figure 16B.

11.Marking the Exit Point of the Roof

Locate the point where the chimney will exit the roof by

plumbing down to the center of the chimney. Drive a nail up

through the roof to mark the center. See Figure 16C.

12.Cutting out the Hole in the Roof

Measure to either side of the nail 7-1/4” and mark the

14-1/2” x 14-1/2” opening required. This is measured on the

horizontal; actual length may be larger depending on the pitch

of the roof. Cut out and frame the opening. See Chapter 25 of

the Uniform Building Code for Roof Framing Details.

Be sure to maintain a 2” minimum air space between the

chimney section and the roof.

13.Assembling the Chimney Sections

Through the Roof

Continue to add chimney sections through the roof opening,

maintaining at least a 2” air space.

Figure 16C - Ceiling/Attic Construction

9. SL-300 MH842 Celing/Roof Thimble

(Cont’d)

NAIL

FLASHING

PLATE

CHIMNEY

THIMBLE

EXTENSION

SCREW

FLASHING

THIMBLE

A

DJUSTABLE

EXTENSION

HOLES

Figure 16A - Installing an MH842 Conguration 3

4-03 17 480-1081

North Star

EPA Certied Fireplace

14.Installing the Roof Flashing

If a roof ashing is to be used, install the roof ashing

appropriate to the roof pitch and install a round termination

cap following the instructions shipped with the cap.

For chase installations you can use a round termination

cap (TR344), a round telescoping termination cap (TR342)

or a square termination cap (ST375). A chase installation

must use a chase top. Chase tops are available from your

dealer. See page 19 for building a chase.

NOTE: Use only a noncombustible material to nish the

face of the replace below the level of the front standoffs.

A noncombustible material such as USG MICORE CV230

Mineral Fiber Board, or USG DUROCK Cement Board is

recommended for this purpose.

15.Completion of the Enclosure

Complete the fireplace enclosure, allowing space for

outside air ducts. Electrical wiring should not come in

contact with the replace. A minimum clearance of 1”

must be maintained between the replace sides and

back and the enclosure. See pages 9-10 for framing

details.

CLEARANCES!

A minimum 1” air clearance must be maintained at

the back and sides of the replace assembly.

Chimney sections at any level require a 2” minimum

air space clearance between the framing and

chimney section.

Figure 17B - Factory Built Hearth Extension

16.Hearth Extension

A hearth extension must be installed with all replaces to

protect the combustible oor in front of the replace from

both radiant heat and sparks.

The construction of, and materials used for a hearth

extension are shown in Figures 17A and 17B. A hearth

extension of this construction may be covered with any

noncombustible decorative material and may have a

maximum thickness as per the illustration. Seal gaps

between the hearth extension and the front of the replace

with a bead of noncombustible sealant.

NONCOMBUSTIBLE

DECORATIVE MATERIAL

(2) HX4 MICORE FACTORY

BUILT HEARTH EXTENSION

(Each HX4 = 1/2" (13mm) thick)

HEARTH METAL STRIPS

GAP (SEAL WITH NONCOMBUSTIBLE SEALANT)

UP TO BOTTOM OF FASCIA

6" (152mm)

1" (51mm)

20"

8" from each side of

fuel loading door

41"

Figure 17A-Field Construction Hearth Extensions

1. Hearth Extension & Floor Protection ush on the oor.

Combustible ooring 20” in front of and 8” to either side of the fuel opening; must be insulated with non-combustible oor

protection with a minimum thickness of 1” (“k” value = 0.43). Use Alternate Material Worksheet on page 18 to determine

the “k” value of the alternative material..

2. Fireplace is ush on the oor and Hearth Extension is raised to the bottom of the fascia:

Raised hearth must be constructed of non-combustible materials such as cement block or equivalent material Decorative

combustible ooring on the raised hearth must be 20” (508mm) in front of and 8” (203mm) to either side of the fuel opening must be

insulated with non-combustible oor protection with a minimum thickness of 1-1/2” (38mm) and (“k” value = 0.43).

3. Fireplace is recessed in the oor to the bottom of the fascia:

Combustible ooring 30” (762mm) in front of and 8” (203mm) to either side of the fuel opening; must be insulated with

non-combustible oor protection with a minimum thickness of 1” (25mm) and (“k” value = 0.43).

480-1081 18 4-03

North Star

EPA Certied Fireplace

WARNING!

Hearth extensions are to be installed only as illustrated to

prevent high temperatures from occurring on concealed

combustible materials. Hearth sealing strips prevent

burning or hot particles from inadvertently falling directly

on combustible surfaces in the event the building should

settle and disturb the original construction.

Seal with non-

combustible sealant

Figure 18A - Position the Hearth Extension

18. Position the Hearth Extension

Position and secure the hearth extension over the

protective metal strips that have been placed partially

under the fireplace front. These strips should be

protruding approximately 2” from under the replace

front and 2” on both sides of the replace opening.

See Figure 13A on page 13. Seal the crack between

the hearth extension and replace with a bead of

noncombustible sealant. See Figure 18A. Apply a

noncombustible nishing material of your choice to the

hearth extension.

NOTE:

SEE PAGE 5 “CLEARANCES TO COM-

BUSTILES, HEARTH EXTENSIONS / FLOOR PROTEC-

TION” FOR CLEARANCES REQUIRED FOR DIFFER-

ENT HEARTH EXTENSION INSTALLATIONS. THE

CLEARANCES MUST BE STRICTLY ADHERED TO.

How to determine if alternate oor protection materials are acceptable:

All oor protection must be non-combustible (i.e., metals, brick, stone, mineral ber boards, etc.). Any organic materials (i.e., plastics, wood paper

products, etc.) are combustible and must not be used. The oor protection specied includes some form of thermal designation such as R-value

(thermal resistance) or k-factor (thermal conductivity).

PROCEDURE:

1. Convert specication to R-value:

2. Determine the R-value of the proposed alternate oor protector.

i. Use the formula in step (1) to convert values not expressed as “R”.

ii. For multiple layers, add R-values of each layer to determine overall R-value.

3. If the overall R-value of the system is greater than the R-value of the specied oor protector, the alternate is acceptable.

EXAMPLE: The specied oor protector should be 3/4 inch thick material with a k-factor of 0.84. The proposed alternate is 4” brick with an r-factor

of 0.2 over 1/8” mineral board with a k-factor of 0.29.

Step (a): Use formula above to convert specication to R-value.

Step (b): Calculate R of proposed system.

=

1

.84

R =

x T

1

k

x 0.75 = 0.893

R

brick

= 0.2 x 4 = 0.431

4" brick of r = 0.2, therefore:

1/8" mineral board of k = 0.29, therefore:

R

mineral board

=

1

0.29

x 0.125 = 0.431

R

total

= R

brick

+ R

mineral board

= 0.8 + 0.431 = 1.231

Step (c): Compare proposed system R

total

of 1.231 to specified R of 0.893. Since proposed system R

total

is greater than required, the system

is acceptable.

DEFINITIONS

1

k

Btu(in)

ft

2

(hr)(

o

F)

= K x 12

(ft

2

)(hr)(

o

F)

Btu

R =

k =

K =

r =

(ft

2

)(hr)(

o

F)

(Btu)(in)

=

Btu(ft)

ft

2

(hr)(

o

F)

R =

x T

1

k

R =

x T

1

K x 12

k-factor is given with a required thickness (T) in inches:

K-factor is given with a required thickness (T) in inches:

r-factor is given with a required thickness (T) in inches: R = r x T

R-value given - no conversion needed.

R =

x T

1

K x 12

R =

x T

1

k

17. Alternate materials worksheet

4-03 19 480-1081

North Star

EPA Certied Fireplace

19. Finishing Material

Do not install combustible materials over the front

of the replace! This poses a safety hazard and may

start a re. You may only use noncombustible material

over the front of the replace.

a. Combustible Material

Material which is made of or surfaced with wood,

compressed paper, plant bers, plastics, or any

material capable of igniting and burning, whether

ame proofed or not, plastered or unplastered.

b. Noncombustible Material

Material which will not ignite and burn. Such

materials are those consisting entirely of steel, iron,

brick, tile, concrete, slate, glass or plasters, or any

combination thereof.

c. Noncombustible Sealant Material

Sealants which will not ignite and burn; General

Electric RTV103 Black (or equivalent), Rutland, Inc.

Fireplace Mortar #63 (or equivalent).

After completing the framing and applying the facing

material (dry wall) over the framing, a 1/2” wide

(maximum) bead of noncombustible sealant must

be used to close off any gaps at the top and sides

between the replace and facing to prevent cold

air leaks.

Only noncombustible materials may be used to

cover the metal replace front.

d. Cardboard OR Metal Template

A cardboard template of the front is printed on the

outside of the shipping box. It measures 1/8” bigger

all the way around than the actual front. Cut out the

template for use in your installation.

A metal template is also available for more durable

continued use remaining accurate over time.

The part number for this metal template is HHT-

Template.

21. Mantel

A combustible mantel may be positioned no lower than

60” from base of the replace. The combustible mantel

may have a maximum depth of 12”. Combustible trim

pieces that project no more than 1-1/2” from the face of

the replace can be placed no closer than 6” from the

side of the replace decorative front. Combustible trim

must not cover the metal surfaces of the replace. This

mantel clearance is in accordance with Section 7-3.3.3

of ANSI/NFPA211.

H. CONSTRUCTING A CHASE

1 2 3

Figure 19A - Chase Constructions

1. Materials

a. The chase is constructed using framing materials

much the same as the walls in your home. A variety

of siding materials may be used including brick,

stone, veneer brick, or standard siding materials.

b. In constructing the chase, several factors must

be considered:

1) Maintain a 2” air space around the chimney.

2) The chase top must be constructed of noncom-

bustible material.

3) In cold climates, a restop spacer should be

installed in an insulated false ceiling at the 8’

level above the replace assembly. This reduces

heat loss through the chase.

4) In cold climates, the walls of the chase should

be insulated to the level of the false ceiling

as shown in Figure 20A on page 20. This will

help reduce heat loss from the home around

the replace.

A chase is a vertical boxlike enclosure built around the

chimney and replace. A chase may be constructed for the

replace and chimney or for the chimney only. It is most

commonly constructed on an outside wall.

In cold climates, it is recommended that the chase oor

be insulated using batt type insulation between the oor

joists.

Three examples of chase applications are shown in Figure

19A.

1. Fireplace and chimney enclosed in an exterior

chase.

2. Chimney offset through exterior wall and enclosed

in chase.

3. Chase constructed on roof.

480-1081 20 4-03

North Star

EPA Certied Fireplace

Figure 20B - Installing a

TR344 Round Termination

Cap

Figure 20C - Installing a

TR342 Round Telescoping

Termination Cap

3. Termination Cap

a. Install the chimney sections up through

the chase enclosure. When using a TR344

round termination cap, the uppermost top

section of pipe must extend 6” above the

top of the chase collar to allow installation

of the storm collar and termination cap.

See Figure 20B.

b. For installations utilizing a TR342 telescop-

ing round termination cap, the uppermost

chimney section must be below the top of

the chase top, but not more than 14-1/2”

below the top of the chase top flashing

collar. See Figure 20C.

c. For installations utilizing an ST375 square

termination cap the last chimney section

must not be more than 4-1/2” below the

chase top. See Figure 20D.

d. For installation utilizing a TS345/TS345P

Square Termination Cap, the uppermost

chimney section must not be more than 3”

below the chase top. See Figure 20E.

e. Attach the chase top (CT35) to the top of

the chase.

f. Install the termination cap, following the

instructions provided with it.

Storm Collar

Chase Flashing

6" min

2" min

Storm Collar

Chase Flashing

2" min

14-1/2" max

Top of uppermost

chimney section

2. Chase Top

Construct a chase of desired materials main-

taining a minimum 2” air space around the

chimney.

Cap

standoff

Top of pipe

2" min from

chase top to

top of chase

flashing

4-1/2"

max

Chase

flashing

Figure 20D - Installing an

ST375 Square Termination

Cap

Chase

flashing

Top of pipe

2" min from chase top to

top of chase flashing

3" max

Figure 20E - Installing

a TS345/TS345P Square

Termination Cap

WARNING!

Never install a single wall slip section or smoke-

pipe in a chase structure. The higher temperature of

this single wall pipe may radiate sufcient heat to

combustible chase materials to cause a re.

WARNING!

Detailed instructions for installation of the chase top, storm

collar and termination cap are packaged with these parts.

To avoid danger of re, all instructions must be strictly

followed, including the provision of air space clearance

between chimney system and enclosure. To protect against

the effects of corrosion on those parts exposed to the

weather, we recommend that the chase top be painted with

a rust-resistant paint.

NEED NEW DRAWING

FIRESTOP

SPACER

METAL CHASE TOP

ROUND TERMINATION CAP

(TR342/TR344)

FALSE

CEILING

Figure 20A - Chase Assembly

Page is loading ...

Heat & Glo North Star User manual

This manual is also suitable for

Heat & Glo North Star User manual

Related papers

Other documents