Seastar Solutions HH4311 Installation guide

Seastar Solutions
Brand
Seastar Solutions
Model
HH4311
Category
Cordless combi drills
Type
Installation guide
INSTALLATION INSTRUCTIONS
Copy Part# 764608, Rev. D, 09/2013 Page 1 of 2
© 2007 Marine Canada Acquisition Inc. DBA SEASTAR SOLUTIONS 3831 No. 6 Road, Richmond, B.C. Canada V6V 1P6 Fax: 604.270.7172 Web: www.seastarsolutions.com
Figure A.
WARNING
Determine desired mounting position of the BayStar Helm pump.
Ensure that the steering wheel will not interfere with any other
functional equipment. Check for adequate space behind the
dash. The BayStar Helm Pump can be installed with the shaft in
the horizontal, vertical or any angle in between. The filler plug
must always be in the uppermost position.
Mounting the Helm
Drilling the Hole
Using the mounting plate on page 2, use the following steps to
make an accurate and clean cut into the dash.
1. Tape the template to the dash and use a center punch for
locating the holes on dash, or photocopy if required to use as
a drilling template. If a photocopy is required check ALL
MEASUREMENTS as per the template to ensure that the
photocopied template is true and correct.
2. Before drilling the holes, check that the helm location will allow
unrestricted movement of the steering wheel.
3. Drill the 3" diameter center hole and the four 5/16" diameter
mounting holes, positioned as shown.
Cleaning fluids containing ammonia, acids or any other corrosive
ingredients MUST NOT be used for cleaning any part of this
Hydraulic Steering System. Failure to comply will cause serious
damage to the steering system, resulting in possible loss of
steering, causing property damage, personal injury and/or death
.
3" DIA.
(76 mm)
4-5/8"
(118 mm)
3-15/16"
(100 mm)
7-15/16" (200 mm)
HELM PUMPS HH4311
AND HH4314
NOTICE
To ease installation, it is recommended that you install the hose
fittings into the rear of the helm pump prior to mounting. See NPT
fitting installations on page 2.
INSTALLATION INSTRUCTIONS
Copy Part# 764608, Rev. D, 09/2013 Page 2 of 2
© 2007 Marine Canada Acquisition Inc. DBA SEASTAR SOLUTIONS 3831 No. 6 Road, Richmond, B.C. Canada V6V 1P6 Fax: 604.270.7172 Web: www.seastarsolutions.com
HELM FLANGE OUTLINE (for reference only)
4-5/8" (118mm) DIA. MAXIMUM COVERAGE
WARNING
Use self-locking type fasteners only; substituting non-self locking
fasteners can result in loosening or separation of equipment and
loss of steering control. DO NOT
exceed 110 in-lbs. (12 Nm)
torque on helm and wedge nuts and bolts.
WARNING
DO NOT use Teflon Tape.
NOTICE
Ports marked R are for the connec-
tion of additional steering stations
and/or an autopilot. Apply a Teflon
based, 'liquid' pipe sealant to the
threads going into the helm pump.
DO NOT use Teflon tape.
Apply a liquid, Teflon based pipe sealant onto the threads going
into the helm pump.
• Tighten fitting HAND-TIGHT.
• Using a wrench, tighten and additional 1.5 turns.
• Continue to tighten until desired orientation is achieved.
NPT Fitting Installations
  • Page 1 1
  • Page 2 2

Seastar Solutions HH4311 Installation guide

Seastar Solutions
Brand
Seastar Solutions
Model
HH4311
Category
Cordless combi drills
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents