2. Vehicles & accessories
  3. Motor vehicle electronics
  4. Radar detectors
  5. Simrad
  6. MARIS 900 MK15 19” 4S & MARIS 900 MK15 24” 4S

Simrad MARIS 900 MK15 19” 4S & MARIS 900 MK15 24” 4S, MARIS 900 MK15 19” 4S & MARIS 900 MK15 24” 4S Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Simrad MARIS 900 MK15 19” 4S & MARIS 900 MK15 24” 4S Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Dimensions - MK15 19” 4S
Dimensions - MK15 24” 4S
MK15 19” 4S MK15 24” 4S
Panel mounting
MARIS ECDIS 900 MK15 19” 4S
MARIS ECDIS 900 MK15 24” 4S
INSTALLATION GUIDE
*988-11130-001*
Bracket mounting (Optional)
For technical specificaons,
cerficates and declaraons,
refer to the product website on:
www.navico-commercial.com
593 mm (23.35”)
76.4 mm (3.01”)
Max height
80.9 mm (3.19”)
Max height
367.9 mm
(14.48”)
318.42 mm
(12.54”)
8.05 mm (0.32”)
40.58 mm (1.60”)
150 mm (5.91”)
4 * M6 threads for Vesa mounting
4 * M6 threads for Vesa mounting,
max 12 mm deep
BACK VIEWSIDE VIEWFRONT VIEW
BACK VIEW
SIDE VIEW
FRONT VIEW
TOP VIEW
TOP VIEW
581 mm (22.87”)
372 mm
(14.65”)
4 * R =
4 mm (0.16”)
4 * R =
4 mm (0.16”)
PANEL CUT-OUT
156.5 mm
(6.16”)
280 mm
(11.02”)
92 mm (3.62”)
150 mm (5.91”)
151 mm (5.94”)
280 mm
(11.02”)
74.5 mm
(2.93”)
384 mm
(15.12”)
577 mm (22.71”)
8 mm (0.31”) 25 mm (0.98”)
45 mm (1.77”)
490 mm (19.29”)
407.93 mm (16.06”)
10.53 mm (0.41”)
412 mm (16.22”)
369 mm
(14.53”)
429 mm (16.89”)
382 mm
(15.04”)
100 mm (3.94”)
182 mm (7.17”)
100 mm (3.94”)
42.9 mm (1.69”)
72 mm (2.87”)
38 mm (1.50”)
PANEL CUT-OUT
334.47mm
(13.17”)
39 mm (1.54”)
A
A
AA
B
B
10
11
13
12
Terminal layout - 19” units
Note 1
Note 2
Note 1
Note 1
Terminal layout - 24” units
Wiring details - Power supply
Parts included
Optional equipment
Wiring details - Serial interface
NOTES
MARIS MK15 19” 4S ECDIS unit
MARIS MK15 24” 4S ECDIS unit
Power cables (240 V AC and 115 V AC)
Terminal block (for 24 V DC)
Terminal blocks (for Serial Interface)
USB DVD drive
ECDIS 900 documentation & dongle kit
Keyboard
Trackball/Mouse
Panel mounting kit for 19”
Panel mounting kit for 24”
Mounting brackets for 19”
Mounting brackets for 24”
USB Extention cable (1 m)
External IEC 61162/1-2 Serial Interface unit
000-12547-001
000-11515-001
000-12523-001
000-12561-001
000-11197-001
000-11008-001
000-11804-001
000-11805-001
000-11802-001
000-11803-001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Grounding screw
RS-232 &
RS-422/RS-485
USB 1,2,3,4
USB 1,2,3,4
2 x
Hard drives
Mic In & Line Out
IEC 61162/1-2
Serial Interface
MK15 19”/24”
Serial Interface unit
INTERFACING
DEVICE
Grounding screw
PS/2 Keyboard
& Trackball/Mouse
RS-232 &
RS-422/RS-485
IEC 61162/1-2
Serial Interface
LAN 1: ECDIS NET
LAN 2: RADAR NET
Power Inputs
DC & AC
Power Inputs
DC & AC
Mic In & Line Out
Not used
Not used
PS/2 Keyboard
& Trackball/Mouse
External IEC 61162/1-2 Serial Interface unit MUST be connected to USB port 1.
USB Extender and E-Token MUST be connected to USB port 2, 3 or 4.
Pin
1
2
3
4
5
6
7
8
9
10
Signal
TX_B
TX_A
GND
RX_B
RX_A
TX_B
TX_A
GND
RX_B
RX_A
Wiring details - Cable securing
24 V DC
115 V AC/60 Hz
230V AC/50 Hz
The ECDIS unit has a dual input power supply which will
accept both AC and DC input.
If both inputs are connected, the unit will be powered by AC.
If AC is disconnected it will automatically switch over to DC
without aecting the operation of the unit. This makes it
possible to use AC power as primary power and a 24V battery
as secondary power.
Parts and Assessories
1
2 3
4
5
6
8
7
9
10
11
14
13
KEY DESCRIPTION PART NO
1
2
3
4
Note 2
DC models must be properly grounded via the screw located on the unit.
To reduce tension of the cables you connect, secure
them with a cable tie to the available chassis hinges
located near the connectors. Note that the actual
position of these hinges may vary depending on the
specic unit.
12
Ports
A
B
C
D
COM
3
4
5
6
LAN 1: ECDIS NET
LAN 2: RADAR NET
/