1
Welcome!
Thank you for purchasing the new table blender SY-BV4. In order to fully benefit from this
product, please read the following instructions carefully. Store this user manual in a safe place
for future reference.
Safety Instructions
Please read the instruction manual before using.
Close supervision is necessary when the appliance is being operated near children.
When shifting the appliance from one place to another, handle it with great care; if the unit
is dropped or hit, it will stop functioning properly.
The appliance should always be laid on a smooth table or plane surface during use.
Do not let the cord hang over the edge of a table or touch hot surfaces.
Make sure the appliance is unplugged when not in use. Only plug in the plug to a wall
outlet, do not use extensions or multi socket outlets as this could provoke a circuit overload.
If your wall outlet becomes loose, the appliance may overheat. Should this occur, contact
Sytech Service Center.
Any attachment which is not supplied with the blender must not be used as it may cause
fire, electric shock or personal injuries.
Make sure the appliance is properly & completely assembled before operating.
Do not touch the small cutting blades in the base of the filter net.
Do not use abrasives cleaners when cleaning this appliance.
This appliance has an over heating protection installed inside, when the appliance overheats,
the power will turn off. The appliance will resume normal functions once cooled down –
usually after 15 minutes.
In order to prolong the life span of the machine, we suggest that the machine should stop
for 3 seconds every 10 seconds. The appliance must not be used for more than 2 minutes
continuously.
If the power cord is damaged, the unit does not function properly, or the blades or other
accessories are broken/damaged contact Sytech Service Center, never try to manipulate the
product by yourself as this may invalidate the guarantee.
Always store in a dry and safe place when the appliance is not being used.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instructions concerning use of the appliance by a person responsible
for their safety.
Do not attempt to remove any parts of the housing nor insert any metal objects into the
interior of the appliance.
To prevent damage to the power cord, always keep it away from sharp edges or corners.
Do not place the power cord over or near hot surfaces.
If the supply cord is damaged, contact Sytech Service Centre
DO NOT operate the appliance if:
The appliance or the power cord are damaged
The appliance has been dropped.
The crystal jug is broken or shows any signs of cracks.
Always remove the plug from the wall socket:
After use
In case of any malfunction
Before cleaning
2
Parts of the SY-BV4
Measure cup
Jar cover
Jar
Cup support
Seal ring
Jar base
Body
Blade asm
Before first use
Check that all the accessories are in the box and the unit is not damaged in any way. Then
insert some water into the jar and mix it (see section “Using the SY-BV4”),
repeat this process 1
or 2 times then pour out the water.
Clean the measuring cup, Lid, Glass jar thoroughly with warm water or in the dishwasher.
Warning: the blade is sharp, handle with great care and ensure that the appliance is unplugged
from the outlet before assembling or removing parts.
3
Using the SY-BV4
To attach the jug, place the jug on top of the motor unit and turn it clockwise (See fig. 1).
Ensure that the eight holes under the jar fix entirely into the fixers on the body. If the
blender doesn’t start functioning, it could mean that the jug is not well placed – remove it
and assemble it once again.
Ensure that the speed selector is on “0” before switching the plug into the wall outlet.
Always peel and remove the seeds from fruits or vegetables and cut them into small pieces
before inserting them into the blender. It is recommended to add a small amount of water
with the food to facilitate the blending process.
Never exceed the maximum level as
indicated on the jar.
Place the ingredients into the jar, place the top cover on the jar and switch the plug into
the wall outlet. Then select the desired speed level to begin the blending process. You can
choose between speed 1 and 10, where 1 is the lowest and 10 the highest. To accelerate
the process of blending you can set the speed to P (Pulse). See figure 2 below.
When in use, you may insert food or any ingredient though the centre opening of the top
cover.
HIGH
low
Low speed(1~5)
High speed(6~10)
Fig.2
PULSE
OFF
6
7
8
9
10
5
4
3
2
1
Stop
At any time ,set the knob
to stop the appliance
Pulse
Set and hold the pulse.
release the to stop
Fig.1
4
Note: Do not use boiling liquids or run the appliance whilst empty.
Do not operate the blender for more than 3 minutes consecutively.
Once the mixture has been blended to your desired consistency, turn the speed selector to
“0” position
Turn anti-clockwise and remove the jar from the Motor unit, carefully remove the measure
cup and then the contents can be poured and served.
Cleaning and Maintenance
The Auto Clean function can clean the blender and blades easily, rapidly and safely.
Pour some warm soapy water into the jar and turn the Speed Selector to P position for a
few seconds
Remove the jar and rinse under running water.
Always wipe the outer surface of the motor unit with a moistened cloth, do not use any
abrasive cleaners.
Never immerse the motor unit in water for cleaning.
Dry all parts thoroughly and place them back in their position.
The blades can be disassembled for complete cleaning. Hold the blades carefully, (Warning:
the blades are sharp) take it out by turning the cup (Fig.3) and the blades at the same time,
in opposite directions. Then place the top cover, measuring cup, the jar and blade assembly
into the dishwasher for cleaning. These parts are all dishwasher safe components. However
make sure that the temperature setting of the dishwasher does not exceed 60º
If any problem has been encountered during use never disassemble the motor base by
yourself, there are no user serviceable parts inside. Contact Sytech Service Centre for any
queries.
Technical Specifications
Electric Table blender
Motor power: 400W.
6 leaf blades of stainless steel
Removable parts for easy cleaning.
10 speeds with Pulse function
Housing material: Plastic
Jar material: Glass
Jar capacity: 1.5L
Safety switch
Weight: 2,98 Kg.
Dimensions: 20 x 17 x 37.5 cm.
Power source: 230V / 50Hz.
5
Declaration of conformity
Manufacturer: Satyatrade S.L
Dirección: Pol. Ind. La Raya, C/ Guadalquivir, 2
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: Table blender
Sytech® SY-BV4 complies with the following directives:
CE Standard: Directive 2004/108/EC
LVD Standard: 2006/95/EC
ROHS Standard: 2011/65/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
6
/
