model
BLN2
BLENDER
Mains supply: ............220-240V ~50Hz
Power consumption:.... 600W
Max operating period:..2 minutes
Because we continually strive to improve our products we may
change specifications and designs without prior notice.
Warning. This blender must NOT be earthed.
Disconnect from the mains before cleaning the blender.
Make sure no water enter the inside of the appliance!
Never immerse the blender or base in water and keep the
electrical contacts dry!
Clean the blender exterior with a soft damp cloth.
Do not use abrasive cleaners or scouring pads which may
damage the finish of the blender.
Rinse the jar under running water.
Should there be a need, the blade assembly can be cleaned
separately. Turn the blade anti-clockwise and the part holding
the blade in place clockwise.
Only use water and dishwashing liquid to clean the blender.
Never put any parts in the dishwasher.
specifications
Cleaning
safety first
Always remove the main plug from the socket when you have finish using the
blender, before you clean the blender, before you put on or remove the
container or if any faults occur.
Wait until the blade have stopped rotating before you remove the jug.
Never use this blender without a lid.
Do not put your hands or any utensils such as forks or spoons into the jug while
the blades are rotating.
Do not immerse in water.
Children should never be allowed to use this blender.
Never leave the appliance plugged in when there are young children around.
Keep the mains lead away from heat.
Do not use the blender if the mains lead or the housing are visibly damaged.
Repairs must only be carried out by qualified electricians.
This blender has been designed for domestic quantities only and is not suitable
for commercial use.
This appliance complies with the appropriate EMC safety directives.
Always place the blender on a firm and level surface.
for the sake of the
environment
Do not simply throw the packaging away. Cardboard packaging can be taken to
your local waste paper collection point. Deposit plastic bags made of
polyethylene (PE) at PE collection points. Please ask you local authority for the
address of your nearest recycling depot.
Do not operate the blender with a damaged cord
or plug or if the blender malfunctions or has
been dropped or damaged in any way.
If the power cord becomes damaged, it must be
replaced by your service agent or qualified
person to prevent a hazard. Please contact the
store where you bought your blender
blender
BLN2
-2-
using your blender
getting to know your blender
Fig. 1
A
B
C
D
E
Description of the Appliance
A Handle
B Jug
C Blades
D Base
E Power dial
F Stainless Jug
Caution: Never use the blender without a lid.
Assembling the blender
Place the base on a dry, stable surface.
Turn the power dial to 0-position.
Place the jug to the base (fig.2)
Operating the blender
Place the base on a stable surface.
Remove the lid (fig. 3) with the ingredients you
want to mix.
Note: The blender can be used for mixing liquids, crushed
ice, grinding and grating of fruits and vegetables,
whipping cream, etc.
fig. 2 fig. 3
fig. 4
Important: Do not exceed the maximum
capacity!
Replace the lid (fig. 4) back onto the jug.
Connect the plug to the mains socket.
Rest on hand on the top of blender jar to place lid securely
in place.
Switch on by turning the power dia (fig. 5) to one of the
position. (1,2,3,4,5 or 6)
For controlled cycle operation, press "pulse" button and hold
down for about 2 seconds. release the "pulse" button to stop
running of blade.
Put the new ingredients into the refill lid and pour through the
hole in the jug (fig. 6).
Place the refill lid back into the hole in the lid and turn it
clockwise until it click into position.
When the blending is finished, switch the power dial (fig. 5)
back to the stop-position"0".
Lift the jug off the base.
Important: Do not operate the blender longer than 2
minutes. After each 2 minutes session the blender must
be allowed to cool down for at least 10 minutes.
fig. 5
Pulse=Manual operation
0 = Stop
1 = Slowest speed
2 = Slow
3 = Medium speed
4 = Fast
5 = Faster
fig. 6
troubleshooting
If the blender doesn't work please check:
the power is switched on and the blender switch is on the
setting except "0".
the fuse in the plug.
F
-3-
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Kambrook KBL120 User manual
-
-
Dualit Kitchen Blender User manual
-
Wolfgang Puck BBLFP050 User manual
-
Cookworks 1.5L Jug Blender User manual
-
Igenix IG8300 Instructions For Use Manual
-
Bosch MMB64G3MAU/01 User manual
-
DeLonghi KF8150M User manual
-
-
Tefal BL811DMX User manual