sec.4b
−−−−
1
2GO! - Technical manual
APARTMENT
DOOR PHONE STATIONS
SECTION 4B
(REV.D)
ATLANTICO DOOR PHONE Ref. 1182 2
DEFAULT PROGRAMMING .............................................................2
INSTALLATION .................................................................................2
Terminal board .............................................................................3
TONE SELECTION ...........................................................................3
Door phone call tone ....................................................................3
Floor call tone ...............................................................................3
Programming data deletion ..........................................................3
UTOPIA DOOR PHONE Ref. 1182/1 4
DEFAULT PROGRAMMING .............................................................4
INSTALLATION .................................................................................4
Terminal board .............................................................................5
TONE SELECTION ...........................................................................5
Door phone call tone ....................................................................5
Floor call tone ...............................................................................5
Programming data deletion ..........................................................5
Adjusting call volume....................................................................5
Download from www.urmetdomus.com Technical Manuals area.
SECTION CONTENTS
Some products may be described in the “New” section.§
APARTMENT DOOR PHONE STATIONS
2
−−−−
sec.4b
2GO! - Technical manual
ATLANTICO DOOR PHONE Ref. 1182
3
2
1
100 mm
236 mm
64 mm
The main characteristics of Atlantico door phones are:
Simple and essential design by Michele De Lucchi.
Plastic fi nishing (white ABS): glossy button, embossed other parts.
Telephone-like handset hook switch arranged in the lower part of
the top.
Condenser (electret) microphone.
Dedicated button for door opener function.
Fixed carriage terminal fi tted on basic printed circuit.
Top clipped onto base without screws.
Handset hook system with tong in upper part of top and housing
in lower part.
White rubber, round cross-section spiral cord with telephone plug
on base on door phone
1
4
5
2
3
1
Apartment internal code dip switch (ID)
2
User code dip switch (CODE)
3
Yellow indicator LED
4
Line terminal switch
5
Terminal board
DEFAULT PROGRAMMING
User Code: 31
Indoor station code: 1
Line termination: ON
•
•
•
•
•
•
•
•
•
ATLANTICO DOOR PHONE Ref. 1182
DEFAULT PROGRAMMING
INSTALLATION
INSTALLATION
1,55 m
To remove the door phone top, lever with the tip of a screwdriver in
the area shown and remove it by turning it on the upper tabs.
Use the holes on the base to fasten the door phone to the wall. Use
the bolts provided with each device.
Refi t the door phone top after installation.
Fasten the door phone to the wall with the bolts provided for
fl ush-mounting in 503 boxes.
Mod. 503
§
ATLANTICO DOOR PHONE Ref. 1182
APARTMENT DOOR PHONE STATIONS
sec.4b
−−−−
3
2GO! - Technical manual
ATLANTICO DOOR PHONE Ref. 1182
TONE SELECTION
Connect the non-polarised Bus line wire to the LINE terminals.
To use the fl oor call or supplementary ringer function, remove the
dedicated terminal protection and connect the respective wires.
Check that the yellow LED on the door phone is off and refi t the hood
as shown below.
TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
CP
}
Floor call button
CP
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
1. Hold the door opener button pressed. Press and release the
button 3. The indoor station will play a tone.
2. Hold the door opener button pressed and press the button 3
again to change the tone.
3. Release the door opener button when you have chosen the tone
you want. The tone is now programmed.
•
•
FLOOR CALL TONE
1. Hold the door opener button pressed. Press and release the
button 2. The indoor station will play a tone.
2. Hold the door opener button pressed and press the button 2
again to change the tone.
3. Release the door opener button when you have chosen the tone
you want. The tone is now programmed.
PROGRAMMING DATA DELETION
Proceed as follows to delete all optional programming data:
1. Hold the door opener button pressed and pick-up the handset.
2. Press 3 and 2 at the same time for 3 seconds until you hear the
deletion tone.
3. Release buttons and hang up.
ATLANTICO DOOR PHONE Ref. 1182
APARTMENT DOOR PHONE STATIONS
4
−−−−
sec.4b
2GO! - Technical manual
UTOPIA DOOR PHONE Ref. 1182/1
1
2
3
225 mm
90 mm 48,5 mm
The main characteristics of Utopia door phones are:
Innovative design.
Open door indicator LED: this function indicates whether the
door corresponding to the main door unit (ID=1) is open (where
applicable).
Dedicated button for door opener function.
Three supplementary buttons for intercom calls, operating electrical
loads and door phone auto power-on.
Adjustable volume with mute function.
Dedicated call speaker with loader, clearer sound.
Telephone-like handset hook switch.
Condenser (electret) microphone.
Fixed carriage terminal fi tted on basic printed circuit.
Top clipped onto base without screws.
Round cross-section spiral cord with telephone plug on base on
door phone.
ON
ON
43215
21
1
3
4
5
2
1
Apartment internal code dip switch (ID)
2
User code dip switch (CODE)
3
Yellow indicator LED
4
Line terminal switch
5
Terminal board
DEFAULT PROGRAMMING
User Code: 31
Indoor station code: 1
Line termination: ON
•
•
•
•
•
•
•
•
•
•
•
INSTALLATION
1
2
3
1,55m
To remove the door phone top, lever with the tip of a screwdriver in
the area shown and remove it by turning it on the upper tabs.
Use the holes on the base to fasten the door phone to the wall. Use
the bolts provided with each device.
Refi t the door phone top after installation.
UTOPIA DOOR PHONE Ref. 1182/1
DEFAULT PROGRAMMING
INSTALLATION
UTOPIA DOOR PHONE Ref. 1182/1
APARTMENT DOOR PHONE STATIONS
sec.4b
−−−−
5
2GO! - Technical manual
Connect the non-polarised Bus line wire to the LINE terminals.
Check that the yellow LED on the door phone is off and refi t the hood
as shown below.
TERMINAL BOARD
LINE
}
Non-polarised bus line
LINE
CP
}
Floor call button
CP
S+ Supplementary ringer connection positive
S- Supplementary ringer connection negative
TONE SELECTION
Five tones can be selected on 2GO! system indoor stations. The tones
can be programmed also by the end user by following the simple
sequence below.
DOOR PHONE CALL TONE
1. Hold the door opener button pressed. Press and release the
button 3. The indoor station will play a tone.
1
2
3
2. Hold the door opener button pressed and press the button 3
again to change the tone.
3. Release the door opener button when you have chosen the tone
you want. The tone is now programmed.
FLOOR CALL TONE
1. Hold the door opener button pressed. Press and release the
button 2. The indoor station will play a tone.
1
2
3
2. Hold the door opener button pressed and press the button 2
again to change the tone.
3. Release the door opener button when you have chosen the tone
you want. The tone is now programmed.
PROGRAMMING DATA DELETION
Proceed as follows to delete all optional programming data:
1. Hold the door opener button pressed and pick-up the handset.
2. Press 3 and 2 at the same time for 3 seconds until you hear the
deletion tone.
3. Release buttons and hang up.
ADJUSTING CALL VOLUME
MAX
Maximum
calling volume
MIN
Minimum
calling volume
Red
MUTE
No calling tone
UTOPIA DOOR PHONE Ref. 1182/1
TONE SELECTION
UTOPIA DOOR PHONE Ref. 1182/1
6
−−−−
sec.4b
2GO! - Technical manual
/
