Duerkopp Adler 745-35-10 User manual

Type
User manual
745-35-10
Additional Instructions
Assembling the long
transport clamp
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2017
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Additional Instructions 745-35-10 - 01.0 - 01/2017 1
1 General information ...................................................................3
2 Assembling the long transport clamp......................................4
3 Adjusting the software settings................................................6
4 Additional settings .....................................................................8
4.1 Selecting the positioning points....................................................8
4.2 Changing the folder......................................................................8
Table of Contents
2 Additional Instructions 745-35-10 - 01.0 - 01/2017
General information
Additional Instructions 745-35-10 - 01.0 - 01/2017 3
1 General information
Class 745-35-10 can be retrofitted with a long transport clamp.
Components of the kit
Check whether the scope of delivery for kit 0745 417754 is correct prior to
installation.
Part number Quantity Description
0745 417824 1 Set of clamps, right, consisting of:
0745 417744, clamp, quantity:1
0745 417764, flap clamp, quantity:1
0745 417834 1 Set of clamps, left, consisting of:
0745 417734, clamp, quantity:1
0745 417774, flap clamp, quantity:1
0791 745790 EN 1 Additional Instructions
Assembling the long transport clamp
4 Additional Instructions 745-35-10 - 01.0 - 01/2017
2 Assembling the long transport clamp
To assemble the long transport clamp:
1. Disassemble the old transport clamp:
Pull the cables off the throttle valves.
Unscrew the transport clamp
Fig. 1: Assembling the long transport clamp (1)
2. Insert the long transport clamp (1) and slightly tighten the screws (2).
3. Connect the cables on both sides of the corresponding throttle valves.
(1) - Long transport clamp (2) - Screws
Assembling the long transport clamp
Additional Instructions 745-35-10 - 01.0 - 01/2017 5
Fig. 2: Assembling the long transport clamp (3)
4. Set the long transport clamp including the screws (3) parallel to the
folder.
5. Tighten the screws (2).
(2) - Screws (3) - Screws
③③
Adjusting the software settings
6 Additional Instructions 745-35-10 - 01.0 - 01/2017
3 Adjusting the software settings
Information
The long transport clamp requires a software version A02.XX.
If the machine has a software version A01.XX a software update must be
performed ( Operating Instructions).
Following the installation of the long transport clamp, the software setting
for the seam length must be set to a greater value.
The greater seam length must be set both in the service menu and in the
program parameters.
Adjusting the setting in the service menu
To set the seam length in the service menu:
1. Select the subitem Machine configuration in the service
menu .
Fig. 3: Adjusting the setting in the service menu (1)
2. Select the subitem Subclass and set the seam clearance to 220 mm:
Adjusting the software settings
Additional Instructions 745-35-10 - 01.0 - 01/2017 7
Fig. 4: Adjusting the setting in the service menu (2)
Adjusting the setting in the program parameters
To set the seam length in the program parameters:
1. Select the item Create seam program in the program
parameters .
Fig. 5: Adjusting the setting in the program parameters
2. Select the subitem Flap scan and set the flap length to 220 mm.
3. Adjust or correct the positioning points of the seam pro-
grams that have already been created.
Additional settings
8 Additional Instructions 745-35-10 - 01.0 - 01/2017
4 Additional settings
4.1 Selecting the positioning points
Following the installation for the long transport clamp, you need to select
new positioning points.
To do so, refer to chapter Aligning the laser modules ( Service
Instructions) and Select positioning points ( Service Instructions,
Operating Instructions).
4.2 Changing the folder
The folder for class745-35-10 A must be changed to a folder with a length
of 220 mm.
To do so, refer to chapter Folder ( Service Instructions).
DÜRKOPP ADLER AG
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: +49 (0) 521 925 00
www.duerkopp-adler.com
Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany
© Dürkopp Adler AG - Original Instructions - 0791 745790 EN - 01.0 - 01/2017
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Duerkopp Adler 745-35-10 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI