Duerkopp Adler 743-221-01 User manual

743-221-01

Service Instructions

Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,

including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

Table of Contents

Service Instructions 743-221-01 - 01.0 - 10/2018 1

1 About these instructions ...........................................................3

1.1 For whom are these instructions intended?..................................3

1.2 Representation conventions – symbols and characters...............3

1.3 Other documents..........................................................................4

1.4 Liability..........................................................................................5

2 Safety...........................................................................................7

2.1 Basic safety instructions...............................................................7

2.2 Signal words and symbols used in warnings................................8

3 Working basis...........................................................................11

3.1 Order of the settings...................................................................11

3.2 Laying the cable guide................................................................11

3.2.1 Swiveling up the machine head..................................................12

3.2.2 Removing and replacing the head cover....................................13

3.2.3 Removing and fitting the arm cover............................................14

3.2.4 Removing and inserting the sliding plate....................................15

3.3 Flats on shafts ............................................................................16

4 Setting the machine head........................................................17

4.1 Gages.........................................................................................17

4.2 Setting the adjusting disc............................................................18

4.3 Setting the arm shaft crank.........................................................19

4.4 Setting the needle thread tension release..................................21

4.5 Setting the thread tensioning spring...........................................22

4.6 Setting the needle bar height......................................................23

4.7 Hook settings..............................................................................25

4.7.1 Setting the loop stroke and the distance of the hook tip to the

needle.........................................................................................25

4.7.2 Setting the hook drive housing...................................................26

4.8 Setting the bobbin case support.................................................28

4.9 Setting the light barrier for the remaining thread monitor...........29

4.10 Setting the winder.......................................................................30

4.11 Setting the position encoder.......................................................31

4.12 Replacing the right-hand arm shaft bearing ...............................32

5 Setting the sewing unit ............................................................35

5.1 Setting the thread trimmer..........................................................35

5.1.1 Assembling and removing the cutter..........................................37

5.1.2 Replacing the piston...................................................................40

5.2 Setting the folding table..............................................................41

5.2.1 Setting the folding table retraction..............................................42

5.2.2 Setting the angular adjustment...................................................44

5.3 Setting the transport carriage.....................................................45

5.3.1 Setting the run-off protection......................................................47

5.4 Setting the configuration set.......................................................48

5.4.1 Setting the guide roller for the configuration set.........................48

5.4.2 Setting the pressing cylinder for the configuration set................49

5.4.3 Setting the closing motion for the configuration set....................50

5.4.4 Setting the configuration set.......................................................52

5.5 Adjusting the pressure monitor...................................................54

Table of Contents

2 Service Instructions 743-221-01 - 01.0 - 10/2018

6 Programming ............................................................................55

6.1 General information....................................................................55

6.2 Calling up the technician level....................................................57

6.2.1 Menu item Machine Config ..................................................58

6.2.2 Menu item User Config .........................................................61

6.2.3 Menu item Service .....................................................................63

6.3 Installing software per dongle.....................................................69

6.4 Checking the functionality of the keys on the control panel........71

7 Maintenance..............................................................................73

7.1 Swiveling up the machine head..................................................74

7.2 Cleaning .....................................................................................75

7.2.1 Cleaning the machine head........................................................75

7.2.2 Cleaning the motor fan sieve......................................................76

7.3 Lubricating..................................................................................77

7.3.1 Checking the machine head lubrication......................................79

7.3.2 Checking the hook lubrication ....................................................79

7.4 Servicing the pneumatic system.................................................80

7.4.1 Setting the operating pressure ...................................................80

7.4.2 Draining the water condensation................................................81

7.4.3 Cleaning the filter element..........................................................82

7.5 Parts list......................................................................................83

8 Decommissioning.....................................................................85

9 Disposal.....................................................................................87

10 Troubleshooting .......................................................................89

10.1 Customer Service.......................................................................89

10.2 Messages of the software...........................................................89

10.3 Errors in sewing process ............................................................94

11 Technical data...........................................................................97

12 Appendix ...................................................................................99

12.1 Wiring diagram ...........................................................................99

12.2 Summary of all settings............................................................103

About these instructions

Service Instructions 743-221-01 - 01.0 - 10/2018 3

1 About these instructions

These instructions have been prepared with utmost care. They contain in-

formation and notes intended to ensure long-term and reliable operation.

Should you notice any discrepancies or if you have improvement re-

quests, then we would be glad to receive your feedback through Custo-

mer Service ( p. 35).

Consider the instructions part of the product and store them in a place

where they are readily available.

1.1 For whom are these instructions intended?

These instructions are intended for:

• Specialists:

This group has the appropriate technical training for performing

maintenance or repairing malfunctions.

With regard to minimum qualification and other requirements to be met by

personnel, please also follow the chapter Safety ( p. 7).

1.2 Representation conventions – symbols and characters

Various information in these instructions is represented or highlighted by

the following characters in order to facilitate easy and quick understan-

ding:

Proper setting

Specifies proper setting.

Disturbances

Specifies the disturbances that can occur from an incorrect setting.

Cover

Specifies which covers must be disassembled in order to access the com-

ponents to be set.

Steps to be performed when operating the machine (sewing and

equipping)

Steps to be performed for service, maintenance, and installation

Steps to be performed via the software control panel

The individual steps are numbered:

First step

Second step

The steps must always be followed in the specified order.

1.

2.

…

About these instructions

4 Service Instructions 743-221-01 - 01.0 - 10/2018

Lists are marked by bullet points.

Result of performing an operation

Change to the machine or on the display/control panel.

Important

Special attention must be paid to this point when performing a step.

Information

Additional information, e.g. on alternative operating options.

Order

Specifies the work to be performed before or after a setting.

References

 Reference to another section in these instructions.

Safety Important warnings for the user of the machine are specifically marked.

Since safety is of particular importance, hazard symbols, levels of danger

and their signal words are described separately in the chapter

Safety ( p. 7).

Location

information

If no other clear location information is used in a figure, indications of right

or left are always from the user's point of view.

1.3 Other documents

The machine includes components from other manufacturers. Each ma-

nufacturer has performed a hazard assessment for these purchased parts

and confirmed their design compliance with applicable European and na-

tional regulations. The proper use of the built-in components is described

in the corresponding manufacturer's instructions.

•



About these instructions

Service Instructions 743-221-01 - 01.0 - 10/2018 5

1.4 Liability

All information and notes in these instructions have been compiled in

accordance with the latest technology and the applicable standards and

regulations.

Dürkopp Adler cannot be held liable for any damage resulting from:

• Breakage and damage during transport

• Failure to observe these instructions

• Improper use

• Unauthorized modifications to the machine

• Use of untrained personnel

• Use of unapproved parts

Transport

Dürkopp Adler cannot be held liable for breakage and transport damages.

Inspect the delivery immediately upon receiving it. Report any damage

to the last transport manager. This also applies if the packaging is not

damaged.

Leave machines, equipment and packaging material in the condition in

which they were found when the damage was discovered. This will ensure

any claims against the transport company.

Report all other complaints to Dürkopp Adler immediately after receiving

the product.

About these instructions

6 Service Instructions 743-221-01 - 01.0 - 10/2018

Safety

Service Instructions 743-221-01 - 01.0 - 10/2018 7

2 Safety

This chapter contains basic information for your safety. Read the instruc-

tions carefully before setting up or operating the machine. Make sure to

follow the information included in the safety instructions. Failure to do so

can result in serious injury and property damage.

2.1 Basic safety instructions

The machine may only be used as described in these instructions.

These instructions must be available at the machine's location at all times.

Work on live components and equipment is prohibited. Exceptions are

defined in the DIN VDE 0105.

For the following work, switch off the machine at the main switch or

disconnect the power plug:

• Replacing the needle or other sewing tools

• Leaving the workstation

• Performing maintenance work and repairs

• Threading

Missing or faulty parts could impair safety and damage the machine.

Only use original parts from the manufacturer.

Transport Use a lifting carriage or forklift to transport the machine. Raise the machi-

ne max. 20 mm and secure it to prevent it from slipping off.

Setup The connecting cable must have a power plug approved in the relevant

country. The power plug may only be assembled to the power cable by

qualified specialists.

Obligations

of the operator

Follow the country-specific safety and accident prevention regulations and

the legal regulations concerning industrial safety and the protection of the

environment.

All the warnings and safety signs on the machine must always be in legible

condition. Do not remove!

Missing or damaged warnings and safety signs must be replaced

immediately.

Requirements

to be met by

the personnel

Only qualified specialists may:

• set up the machine / put the machine in operation

• perform maintenance work and repairs

• perform work on electrical equipment

Only authorized persons may work on the machine and must first have

understood these instructions.

Safety

8 Service Instructions 743-221-01 - 01.0 - 10/2018

Operation Check the machine during operating for any externally visible damage.

Stop working if you notice any changes to the machine. Report any chan-

ges to your supervisor. Do not use a damaged machine any further.

Safety

equipment

Safety equipment should not be removed or deactivated. If it is essential

to remove or deactivate safety equipment for a repair operation, it must be

assembled and put back into operation immediately afterward.

2.2 Signal words and symbols used in warnings

Warnings in the text are distinguished by color bars. The color scheme is

based on the severity of the danger. Signal words indicate the severity of

the danger.

Signal words Signal words and the hazard they describe:

Symbols The following symbols indicate the type of danger to personnel:

Signal word Meaning

DANGER (with hazard symbol)

If ignored, fatal or serious injury will result

WARNING (with hazard symbol)

If ignored, fatal or serious injury can result

CAUTION (with hazard symbol)

If ignored, moderate or minor injury can result

CAUTION (with hazard symbol)

If ignored, environmental damage can result

NOTICE (without hazard symbol)

If ignored, property damage can result

Symbol Type of danger

General

Electric shock

Safety

Service Instructions 743-221-01 - 01.0 - 10/2018 9

Examples Examples of the layout of warnings in the text:

 This is what a warning looks like for a hazard that will result in serious

injury or even death if ignored.

 This is what a warning looks like for a hazard that could result in seri-

ous or even fatal injury if ignored.

 This is what a warning looks like for a hazard that could result in

moderate or minor injury if the warning is ignored.

Puncture

Crushing

Environmental damage

Symbol Type of danger

DANGER

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

WARNING

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

CAUTION

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

Safety

10 Service Instructions 743-221-01 - 01.0 - 10/2018

 This is what a warning looks like for a hazard that could result in

environmental damage if ignored.

 This is what a warning looks like for a hazard that could result in pro-

perty damage if ignored.

CAUTION

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

NOTICE

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

Working basis

Service Instructions 743-221-01 - 01.0 - 10/2018 11

3 Working basis

3.1 Order of the settings

Order

The setting positions for the machine are interdependent.

Always comply with the order of individual setting steps as specified.

It is absolutely essential that you follow all notices regarding prerequisites

and subsequent settings that are marked with in the margin.

3.2 Laying the cable guide

Ensure that all cables are laid in the machine such that the function of mo-

ving parts is not hampered.

To lay the cable guide:

1. Lay any excess cabling neatly in proper cable snakes.

2. Bind together the cable loops with cable ties.

Important

Tie loops wherever possible to fixed parts.

The cables must be secured firmly.

3. Cut off any overlapping cable ties.

NOTICE

Property damage may occur!

Risk of machine damage from incorrect order.

It is essential to follow the working order specified in these

instructions.

NOTICE

Property damage may occur!

Excess cables can impair the functioning of moving machine parts.

This impairs the sewing function and can result in damage.

Lay excess cable as described above.

Working basis

12 Service Instructions 743-221-01 - 01.0 - 10/2018

3.2.1 Swiveling up the machine head

Fig. 1: Swiveling up the machine head

To swivel up the machine head:

1. Pivot the supporting table (1), bundle clamp, and ejector to the side.

2. Move the configuration set (2) into the left end position.

3. Carefully pivot up the upper machine section using the handle (3) and

lean it against the folding support.

 The upper machine section is held in this position through the loca-

tion of the center of mass.

4. Lower the machine in the same way.

WARNING

Risk of injury from moving parts!

Crushing possible.

Switch off the machine before swiveling up the

machine head.

(1) - Supporting table

(2) - Configuration set

(3) - Handle

③

②

①

Working basis

Service Instructions 743-221-01 - 01.0 - 10/2018 13

3.2.2 Removing and replacing the head cover

Fig. 2: Removing and replacing the head cover

Removing the head cover

To remove the head cover:

1. Loosen the glass protection screws (3).

2. Remove the glass protection.

3. Loosen the head cover screws (1).

4. Remove the head cover (2).

Replacing the head cover

To replace the head cover:

1. Replace the head cover (2).

2. Tighten the head cover screws (1).

3. Position the glass protection.

4. Tighten the glass protection screws (3).

(1) - Screws

(2) - Head cover

(3) - Glass protection screws

①

②

①

③

Working basis

14 Service Instructions 743-221-01 - 01.0 - 10/2018

3.2.3 Removing and fitting the arm cover

Fig. 3: Removing and fitting the arm cover

Removing the arm cover

To remove the arm cover:

1. Losen the screws (1).

2. Remove the arm cover (2).

Fitting the arm cover

To fit the arm cover:

1. Fit the arm cover (2).

2. Fasten screws (1).

(1) - Screws (2) - Armcover

①

②

Working basis

Service Instructions 743-221-01 - 01.0 - 10/2018 15

3.2.4 Removing and inserting the sliding plate

Fig. 4: Removing and inserting the sliding plate (1)

To remove the sliding plate:

1. Remove the configuration set (2).

2. Remove the casing (4).

3. Losen the light barrier (5) and thread trimmer (3) and put them down

on the oil pan.

Fig. 5: Removing and inserting the sliding plate (2)

4. Losen the screws (6) on the sliding plate and remove the sliding plate.

NOTICE

Property damage may occur!

Damage to the needle or the sliding plate.

The centring discs must not be twisted. These are used to align the

sliding plate to the needle.

(1) - Gage

(2) - Configuration set

(3) - Thread trimmer

(4) - Casing

(5) - Light barrier

①

③

②

④

⑤

(6) - Screws (7) - Centring discs

Working basis

16 Service Instructions 743-221-01 - 01.0 - 10/2018

3.3 Flats on shafts

Fig. 6: Flats on shafts

Some shafts have flat surfaces at the points where the components are

screwed on. This stabilizes the connection and makes setting easier.

For all settings on the surface, the first screw is screwed in rotational

direction onto the surface.

Important

Always ensure that the screw faces are completely flush with the surface.

(1) - Flat (2) - Shaft

2

1

Setting the machine head

Service Instructions 743-221-01 - 01.0 - 10/2018 17

4 Setting the machine head

4.1 Gages

Fig. 7: Gages

The setting gages listed below allow you to precisely set and check the se-

wing unit.

WARNING

Risk of injury from moving parts!

Crushing possible.

Switch off the machine before setting the machine

head.

WARNING

Risk of injury from sharp parts!

Puncture possible.

Switch off the machine before setting the machine

head.

(1) - Locking peg

(2) - Gage

(3) - Feeler gage

(4) - Gage

(5) - Sleeve

Position Setting gage Order number Use

1 Locking peg 9301 022608 For locking the sewing unit in

place at position A - F.

2 Gage 0935 107077 For aligning the transport car-

riage, checking the reference

point, guide roller, and center

of the needle.

Setting the machine head

18 Service Instructions 743-221-01 - 01.0 - 10/2018

4.2 Setting the adjusting disc

Fig. 8: Setting the adjusting disc

Use the locking peg (3) and the adjusting disc (4) integrated on the toothed

belt wheel of the arm shaft to lock the sewing unit in place in all setting po-

sitions.

To do this, the adjusting disc is equipped with six slots which are identified

on the handwheel (1) with the letters A, B, C, D, E, and F. In conjunction

with the marking (2), the letters indicate the position of the slots in which

the machine can be locked in place using the peg (3).

Slot A (loop stroke position) is deeper than the other slots. In the individual

positions, the following can be set:

3 Feeler gage 0933 080200 For setting and checking the

guide roller.

4 Gage 0935 107071 For aligning the needle bar

height and hook drive housing.

5 Sleeve 0935 107090 For aligning the remaining

thread monitor.

(1) - Handwheel

(2) - Marking

(3) - Locking peg

(4) - Adjusting disc

Slot Setting

A Adjusting disc to groove in the arm shaft crank, belt wheel,

loop stroke, distance of hook tip to needle

B No function

C 2. Needle position (thread lever upper position)

D No function

E Needle bar height

F No function

Position Setting gage Order number Use

①

②

③

④③

Page is loading ...

Duerkopp Adler 743-221-01 User manual

Duerkopp Adler 743-221-01 User manual

Related papers

Other documents