Nuface Trinity User manual

Brand: Nuface

Model: Trinity

Category: Skin care appliances

Type: User manual

Nuface Trinity is an advanced skincare device that uses microcurrent technology to improve facial contour, reduce fine lines and wrinkles, and stimulate collagen and elastin production. It features interchangeable treatment attachments, including a Wrinkle Reducer that utilizes red and infrared light therapy to specifically target and reduce the appearance of fine lines and wrinkles. With regular use, Nuface Trinity can help rejuvenate your skin, leaving it looking smoother, firmer, and more youthful.

Wrinkle Reducer

Attachment

USER MANUAL

TABLE OF CONTENTS

01 Introduction

02 Ideal User

02 Getting to Know Your Device

02 Before Using Your Attachment

03 Usage Instructions

03 Indications for Use

03 Contraindications for Use

04 Treatment Steps

05 Treatment Frequency

05 Results

06 Frequently Asked Questions

06 Caring for Your Device

06 Temperature Sensor

06 Cleaning

07 Troubleshooting

08 International Usage

08 Important Information

08 Risks

08 Precautions

09 Warnings

10 Warranty

INTRODUCTION

NuFACE TRINITY® WRINKLE REDUCER ATTACHMENT

The NuFACE Trinity Wrinkle Reducer (Wrinkle Reducer)

uses a precise combination of red and infrared lights to

reduce the appearance of wrinkles. There are 36 LEDs in

the attachment, composed of 32 red LEDs and 4 infrared

LEDs that illuminate when the device is turned on and

placed on the skin. Please note, the infrared light is not

visible to the naked eye. This means that the infrared LEDs

will not appear to be on when in use. However, they are on

whenever the red LEDs are illuminated.

IDEAL USER

The Wrinkle Reducer is for anyone wanting to reduce the

appearance of ﬁne lines and wrinkles.

GETTING TO KNOW YOUR DEVICE

1. POWER ON/OFF BUTTON

2. INTENSITY CONTROL UP

3. INTENSITY CONTROL DOWN

4. PROTECTIVE SHIELD/SKIN SENSOR

5. TRINITY WRINKLE

REDUCER ATTACHMENT

6. ATTACHMENT

RELEASE BUTTON

BEFORE USING YOUR

ATTACHMENT

1. The Wrinkle Reducer’s unique

technology ﬂashes the LEDs to provide improved

results. Use in a well-lit room if you ﬁnd the ﬂashing

lights bothersome.

2. Firmly press the release button to remove or fasten

the attachment.

3. When fastening a new treatment

attachment, press the release button,

guide the attachment in place

(as pictured), and then release the

button to secure the attachment to

your NuFACE Trinity device.

4. For most devices, the +/- keys are not

active when the Wrinkle Reducer is

attached. If your device’s +/- keys are

active, increase the power so all ﬁve

output lights are illuminated.

5. Test your skin to make sure you are not sensitive to light.

To do so, place the Wrinkle Reducer on your forearm

for 3 minutes and then check the area. If it turns red

and lasts for more than 2 hours, your skin is sensitive

to light and you should not use the Wrinkle Reducer. 2

6. Before treatment, take a photo of your cleansed face

in a well-lit room to document your results. After

treatment, take a photo of your face/problem areas.

Every eight weeks, take another photo of your face

in the same room with the same lighting at the same

location. Compare results to previous weeks

of treatment.

USAGE INSTRUCTIONS

INDICATIONS FOR USE

The Wrinkle Reducer is an over-the-counter hand-held

device intended for the treatment of full-face wrinkles.

CONTRAINDICATIONS FOR USE

• Do not use if you have a history of seizures, especially

if you have photosensitive epilepsy, as the pulsing light

could induce seizures.

• Do not use on the neck if diagnosed with or suspect a

thyroid problem.

• Do not use the Wrinkle Reducer if your skin is sensitive

to light. People can be sensitive to light and not be

aware of it. In addition, certain drugs or cosmetics can

cause skin sensitivity, as well as other factors. See the

“Before Using Your Attachment” section for directions to

test your skin.

• Do not use over any suspicious or cancerous

lesion — consult your doctor.

• Do not use over topical or systemic steroids.

• Do not use if you are pregnant.

• Do not use on infants and children under the age of 14,

and keep device and attachments out of the reach of

children.

TREATMENT STEPS

1. Follow all of the steps indicated in the “Before Using

Your Attachment” section.

2. Cleanse your face with an oil-free cleanser. Note: Do

not use the NuFACE Gel Primer with the Wrinkle

Reducer. The Gel Primer is for use with microcurrent

devices/attachments only.

3. Remove your device from the charging cradle and turn

it on by pressing the ON/OFF button. An ascending

audible beep is emitted notifying you that your device

is on, and the red LEDs will ﬂash rapidly 3 times. Do

not touch the Wrinkle Reducer shield until the unit has

ﬁnished ﬂashing.

4. Divide the face into 7 sections as pictured (Page 5).

5. Place the Wrinkle Reducer in direct contact with your

clean, dry skin, over the area to be treated. Your

Wrinkle Reducer has a skin sensor that will illuminate

the red LEDs when in complete contact with your

skin. Press ﬁrmly enough to keep the Wrinkle Reducer

in direct contact with your skin. The device should

be used on lines and wrinkles within the section, not

speciﬁcally where the number appears on the photo.

Treat each section for 3 minutes until beep sounds.

6. If the Wrinkle Reducer is not touching the skin, your

device will emit 3 beeps notifying you to hold directly

on your skin.

7. Your device will automatically shut off after 21 minutes

indicating you are now ﬁnished with the treatment.

Section 1

Hold on areas of the left

upper lip, lower lip and

lower cheek/jowl.

Section 2

Hold on areas of the left

upper cheek.

Section 3

Hold on areas of the left

under eye area (orbital

bone of the eye). DO

NOT treat upper eyelid.

Section 4

Hold on areas of the

right upper lip, lower lip

and lower cheek/jowl.

Section 5

Hold on areas of the

right upper cheek.

Section 6

Hold on areas of the

right under eye area

(orbital bone of the

eye). DO NOT treat upper eyelid.

Section 7

Hold on areas across the forehead.

TREATMENT FREQUENCY

• Use no more than 3 minutes per area, up to 21 minutes a

day for the entire face. Do not overlap areas.

• For the ﬁrst 60 days, use 5 times per week.

• After 60 days, use 2-3 times per week for maintenance.

• Allow 24 hours between treatments.

RESULTS

It takes about 8 weeks to see the start of the reduction in

the appearance of ﬁne lines and wrinkles. Some users see

results in a shorter period of time, while others take longer.

Results may vary based on skin type and skin damage.

LEFT RIGHT

FREQUENTLY ASKED QUESTIONS

1. Why do I hold the Wrinkle Reducer directly on my skin?

To allow your skin to absorb as much light as possible.

2. Why does the Trinity Wrinkle Reducer ﬂash?

It ﬂashes when it’s in use to increase the efﬁcacy of the

treatment. The ﬂash treatment is unique to NuFACE.

If you’re sensitive to the lights, you can wear goggles.

You can purchase goggles from your local drugstore.

3. Why do some of the red LEDs look like they aren’t

on? Some of the LEDs are infrared, which are not

visible to the naked eye.

4. How long will it take to see results? It usually takes

6 to 8 weeks to see the start of the reduction of ﬁne

lines and wrinkles. Some people see results in a shorter

period of time, while others take longer.

5. What can I do to maintain results? Once you achieve

your desired results, use the device 2-3 times per week

for maintenance.

6. Can I use my favorite anti-aging creams or serums

with my Wrinkle Reducer? Yes.

7. How long do the red LEDs last? The red LEDs

are unique and are designed to last more than

25,000 hours.

CARING FOR

YOUR DEVICE

TEMPERATURE SENSOR

The Wrinkle Reducer will

normally get warm during

a treatment. A temperature

sensor will turn the device

off if the internal attachment

temperature exceeds 129.5°F.

Allow the device to cool for

30 minutes before reuse should

this occur.

CLEANING

Use a damp, soft, lint-free cloth and water or rubbing

alcohol to clean the Wrinkle Reducer. Do not immerse in

water at any time. 6

TROUBLESHOOTING

If your Wrinkle Reducer is not turning on, please make

sure all the below are true:

• The Wrinkle Reducer is completely attached to the

device and ﬁts snugly. Make sure to ﬁrmly press the

release button when attaching and detaching the

Wrinkle Reducer.

• The NuFACE Trinity device battery is fully charged. If

not, please charge your device for a full 12 hours. The

NuFACE Trinity device battery needs to be fully charged

as the Wrinkle Reducer takes more power than the

Facial Trainer Attachment (microcurrent).

• The Wrinkle Reducer is pressed completely to the skin,

activating (or turning on) the LEDs. Remember, the

Wrinkle Reducer has a skin sensor making the red LEDs

turn on only when in complete contact with your skin.

• The Wrinkle Reducer has been allowed to self-calibrate.

The attachment will automatically calibrate within

the ﬁrst few seconds of turning on the device. This is

indicated by three rapid ﬂashes of the red LEDs. Make

sure you do not touch the Wrinkle Reducer while the

device is calibrating.

• The gold connector board (as

pictured) is clean. Avoid getting

any gel, skin care products or dirt

on the connector board. Should

the connector board get dirty, we

recommend wetting a cotton swab

(not a cotton ball) with isopropyl

alcohol to clean the face of the

connector board, wipe dry, and

then air dry for one hour before use.

If all the above are true and your Wrinkle Reducer is

still not working please call NuFACE customer service

at 888-360-9171. We’re here to help!

INTERNATIONAL USAGE

The Wrinkle Reducer is compatible worldwide as it

is connected to the worldwide compatible NuFACE

Trinity device.

IMPORTANT INFORMATION

RISKS

The risks and dangers of using the Wrinkle Reducer in

any way that does not follow this User Manual may be un-

known. Use the Wrinkle Reducer only as described within

this User Manual. The Wrinkle Reducer was not tested for

use over the eye socket or eyelid so the risks are unknown.

PRECAUTIONS

• If using the device causes any discomfort, discontinue

use immediately.

• Overuse of this device may result in dryness of

the skin.

• Contact a doctor immediately if you suspect that you have

had a negative reaction from using the Wrinkle Reducer.

• Do not store the attachment in the sun or on a hot

surface. High temperature may be damaging.

• Do not disassemble the attachment as this may cause

damage, malfunction, electrical shock, ﬁre or injury.

There are no user-serviceable parts inside.

Note: Disassembly voids the warranty.

• Do not operate in an environment where other devices,

that intentionally radiate electromagnetic energy in an

unshielded manner, are being used. Portable or mobile

radio frequency communication equipment can affect

medical electrical equipment.

• Failure to use and maintain the NuFACE Trinity Wrinkle

Reducer in accordance with the instructions outlined in

this manual will void the warranty.

• Always protect your skin from the sun. The sun may

cause wrinkles and reduce the beneﬁts of the Wrinkle

Reducer.

• Do not look directly into the Wrinkle Reducer’s LEDs or

shine in the eyes while in operation as this may cause

you to see spots for a few moments. The skin sensor on

the Wrinkle Reducer will help protect you from the lights

as the Wrinkle Reducer must be in contact with the skin

to activate the lights.

WARNINGS

• Never operate this device if it is not working properly,

if it has been dropped or damaged, or submerged

in water.

• Never drop or insert any object into any openings on

the device.

• Only use the power adapter provided with the NuFACE

Trinity System.

• Do not scratch or damage the treatment attachment.

• Use of controls or adjustments, or performance of

procedures other than those speciﬁed herein, may result

in injury.

• Keep all electrical appliances (including NuFACE Trinity

device and treatment attachments) away from water

(including baths and showers).

• Do not use ﬂammable aerosol products or oxygen near

the device.

• If the NuFACE Trinity device begins to overheat, turn off

immediately.

• Stop using the device immediately if you believe the

device is malfunctioning. Return the device to Carol

Cole Company for examination and repair.

WARRANTY

The Carol Cole Company warrants that the NuFACE® device and

attachments are free of defects in materials and workmanship for one (1)

year from the date of purchase. This warranty is valid only in accordance

with the conditions set forth below. Abnormal wear and tear, such as

submersions and drops, are not covered by this warranty. This one

(1) year warranty applies to consumer use only and is void when the

product is used in a commercial or institutional setting. This warranty

extends only to the original consumer purchaser and is not transferable.

In addition, proof of purchase must be demonstrated. This warranty is

void if the product has been subject to accident, misuse, abuse, improper

maintenance or repair, unauthorized modiﬁcation, or any other use not

found in the printed instructions. This limited warranty is the only written

or expressed warranty given by the Carol Cole Company. Any implied

warranties on the product (including but not limited to any implied

warranties of merchantability or ﬁtness for a particular purpose) are

limited in duration to the duration of this warranty. Some states do not

allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. Repair or replacement of the product is

the exclusive remedy available to the consumer under this warranty. The

Carol Cole Company shall not be liable for any incidental or

consequential damages for breach of this warranty or any implied

warranty on this product. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you.

PROCEDURE FOR WARRANTY REPAIRS OR REPLACEMENT

If warranty service is necessary, the original purchaser must

contact the Carol Cole Company for warranty service instructions.

Carol Cole Company

Returns/Repairs

1325 Sycamore Avenue, Suite A

Vista, CA 92081 USA

For your protection, it is suggested you insure the return of the

device to the Carol Cole Company. Damage occurring during

shipment is not covered by this warranty. Returns that are missing

proper documentation and/or any shipping and handling charges

will not be processed.

1.888.360.9171 | info@myNuFACE.com | www.myNuFACE.com

1.888.360.9171 l info@myNuFACE.com l www.myNuFACE.com

NuFACE® is a registered trademark of the Carol Cole Company.

Manufactured by Carol Cole Company.

Made in U.S. from Imported Parts l Vista, CA 92081

L-0025.V5

Nuface Trinity User manual

Brand: Nuface

Model: Trinity

Category: Skin care appliances

Type: User manual

Download PDF

report

Nuface Trinity User manual

Nuface Trinity User manual

Related papers

Other documents