Resol Calvio Owner's manual

Brand: Resol

Model: Calvio

Type: Owner's manual

CALVIO

www.resol.de

Thank you for buying this RESOL product.

Please read this manual carefully to get the best performance from this unit.

RESOL CALVIO

Mounting

Connection

Handling

*48000140*

48000140

CALVIO

| 2

Contents

Safety advice .......................................................................................................... 2

Technical data and function survey ..................................................................... 3

1. Installation of the transmitting module ................................................ 4

2 Operation and function .......................................................................... 4

3. Flashing codes .......................................................................................... 5

4. Changing the batteries ........................................................................... 5

5. Device family number ............................................................................. 6

6. Trouble shooting ...................................................................................... 7

Imprint ................................................................................................................... 8

Safety advice

Please pay attention to the following

safety advice in order to avoid danger

and damage to people and property.

This product is to be used in accor-

dance with its intended use only (see

page 3).

Instructions

Attention should be paid to

- the statutory provisions for preven-

tion of industrial accidents,

- the statutory provisions for environ-

mental protection,

- the Health and Safety at Work Act

1974

- Part P of the Building Regulations

2005

- BS7671 Requirements for electrical

installations and relevant safety re-

gulations of DIN, EN, DVGW, TRGI,

TRF and VDE.

These instructions are exclusively

addressed to authorised skilled per-

sonnel.

- Only qualified electricians should

carry out electrical works.

- Initial installation must be effected

by qualiﬁed personnel named by the

manufacturer

Declaration of conformity

We, RESOL Elektronische Regelungen GmbH, D-45527 Hattingen, declare under

our sole responsibility that our product CALVIO complies with the following

standards:

EN 55 014-1

EN 60 730-1

According to the regulations of the above directives, the product is labelled with

89/336/EWG

73/ 23/EWG

Hattingen, 19.02.2007

RESOL Elektronische Regelungen GmbH,

ppa. Gerald Neuse

CALVIO

3 |

Transmitting module

130

Technical data

Transmitting module:

Housing: plastic, PC-ABS and PMMA

Protection type: IP 20 optional IP 22

(DIN 40050)

Ambient temp.: 0 ... 40 °C

Size: Ø 130 mm, depth 45 mm

Mounting: wall mounting

Display: 1 functional control lamp

Sensors: sensor chain with 8

temperature sensors, 1,5 m

Length of sensor chain: 1,5 m, total

length 3 m

Power supply: 220 ... 240 V~

Receiver module:

Housing: acrylic glass with aluminium

plugs

Size: Ø 50 mm, height 150 mm

Indication: 8 variable red/blue light

emitting diodes

Range of indication:

Standard: clear blue = T ≤� 25 °C

clear red = T ≥� 55 °C

Buffer storage:

clear blue = T ≤ 40 °C

clear red = T ≥�85 °C

Power supply: 2 x Mignon AA 1,5 V

152 mm

8 mm

Receiver and

display module

CALVIO - See the Heat!

Visualizing the amount of stored heat provides enhanced control as well as

information. The user can see at a glance whether the storage is warm and the

heat layering stable or if it is losing heat too quickly.

A sensor chain detects temperatures in the eight different layers of the storage.

Data is queried over a digital bus system by a controller unit and transformed

into transmittable information. In order to avoid unnecessary electrical smog

and to extend battery life, wireless data transmission occurs for just a fraction

of a second when required by the receiver and indication module (activated by

touching the upper cover).

The display module receives the temperature information and makes it easy to

read using colour-changing red/blue light emitting diodes.

The warm water supply indicator allows the adjustment of consumption beha-

vior and, if necessary, the use of an additional heating system that is optimized

according to individual requirements. Through simple visualization, CALVIO thus

increases the solar coverage portion without loss of convenience.

Dangerous voltage

on contact!

Electrostatic discharge

can lead to damage of

electronic components!

CALVIO

| 4

The unit must be installed in a dry interior location. Please

note that in order to function correctly, the device should

not be exposed to any electromagnetic ﬁelds, e.g. of ﬂuore-

scent lamps and large electric motors.

• Choose a location for fastening the transmission module

near the storage or directly at the storage (take into

account the length of the sensor chain).

• Fasten the transmitting module using the two clearance

holes.

• Fasten the sensor chain to the outer layer below the

insulation of the storage. If necessary, use temperature-

resistant adhesive tape. Arrange the sensor chain for “big“

(storage wall height >= 1.4m) and “small“ (storage wall

height < 1.4m) storage constructions according to the

patterns on the left.

• Connect the mains plug of the transmission module to

the mains.

• Insert batteries into the receiver module (see page 5).

Transmitting and receiver module are then ready for ope-

ration.

1. Installation of the transmitting

module

fastening holes

2. Handling and Function

Touching the upper cylindrical cover turns the display on for

10 seconds. Temperature layers are indicated using red and

blue LEDs. As is common, blue is assigned to low tempera-

tures and red to high.

The control lamp of the transmitting module switches off to

indicate data communication. The yellow LED at the bottom

of the receiver and indication module is on during the time

the connection is established.





Storage “big“ Storage “small“

mains feeder

sensor chain

1 2 3 4 5 6 7 8

CALVIO

5 |

3. Flashing codes Transmitting module

• After the supply voltage has been switched on, the yellow

control LED ﬂashes (usually 1 x).This ﬂashing signals that

the transmitting module and the receiver module recog-

nize each other.

• Uninterrupted lighting signalises readiness for operation.

• If the light extinguishes for a short period of time, data

(temperature values) have been requested by the recei-

ver module.

Receiver and display module

• After the upper cover has been touched for a longer pe-

riod of time, the number of illuminating LEDs indicates

the device family number. Illuminating blue LEDs indicate

that the transmitting module has been conﬁgurated for a

standard storage. A corresponding indication by red LEDs

indicates that the transmitting module has been conﬁgu-

rated for the buffer storage.

• A short lighting up (max. 1 sec.) of the yellow LED in-

dicates that data have been requested (by touching the

surface of the cover).

• If the yellow LED ﬂashes every 0,5 sec. during the tempe-

rature distribution indication, the batteries are too weak.

The batteries have then to be replaced.

3. Changing the batteries

Attention:

Avoid damage caused by electrostatic discharges. Before

beginning any intervention, divert charges by touching

metallic surfaces, such as radiators and water taps.

In order to replace the batteries, unscrew and remove

the two screws at the lower cylinder plug of the receiver

module. Then remove the lower cylinder plug and take out

the battery holder.

Replace the batteries in the holder with two new ones of

the type Mignon AA 1,5V.

Please conduct the assembly in reverse order.

Do not use batteries by different manufacturers. Use full

batteries only and do not use full batteries along with used

batteries..

cylinder

plug

screws



LED (yellow)

control LED

LED (red/blue)

Advice:

cover

CALVIO

| 6

4. Device family number Warning!

Switch-off power supply and remove

plug from the mains before opening

the housing!

Transmitting and receiver module must have the same device

family number in order to be able to communicate with each

other. The device family number 1 is set by the manufacturer

and the device is ready for opeartion after installation.

If other modules are also near your module (e.g. in the

neighborhood), it can happen that the installed module also

receives data from these other modules. In order to avoid

this, another addresses or device family number should be

used. To set the device family number, use the DIP switches

inside the transmitting and the receiver modules. All DIP-

switches are set in the OFF position by the manufacturer

(corresponding to device family number 1). The adjustable

positions of the DIP-switches with the corresponding device

family number are shown in the table to the left.

DIP-switch 4:

transmitter module: assigned

receiver module: standard / buffer storage

In order to use the DIP-switches in the transmitter mo-

dule, open the housing:

• Unscrew screws (1) on the top and the bottom and

remove the housing cover.

• Unscrew screw (2) in the cover and remove cover..

housing cover

cover base

DIP-switches

DIP-switch device family

number

123

OFF OFF OFF 1

ON OFF OFF 2

OFF ON OFF 3

ON ON OFF 4

OFF OFF ON 5

ON OFF ON 6

OFF ON ON 7

ON ON ON 8

DIP-

switch 4

sensor chain

fastened to blue red

OFF standard storage < 25 °C > 55 °C

ON buffer storage < 40 °C > 85 °C

CALVIO

7 |

DIP-switches

To use the DIP-switches in the receiver module, unscrew

the screws at the lower cylinder plug and remove lower

plug (see page 5). Now, 4 DIP-switches can be seen.

6. Trouble shooting Should the temperature distribution not be indicated after

data has been requested by the receiver module and after

the yellow LED has extinguised, the following could be the

cause:

• The transmitting module has no voltage. Insert the mains

plug into the mains.

• The device family number of transmitting and receiver

module are not identical. Adjust the device familiy num-

ber (see p. 6).

If the LED does not light up after the receiver module has

requested data, and if no other indication is made, it may

be the case that the batteries are empty. Replace batteries.

CALVIO

| 8

Distributed by:

Please note:

The design and the speciﬁcations are to be changed without notice.

The illustrations may differ from the original product.

RESOL - Elektronische Regelungen GmbH

Heiskampstraße 10

D - 45527 Hattingen

Tel.: +49 (0) 23 24 / 96 48 - 0

Fax: +49 (0) 23 24 / 96 48 - 755

www.resol.de

info@resol.de

Reprinting / copying

This mounting- and operation manual including all parts is

copyrighted. Another use outside the copyright requires

the approval of RESOL - Elektronische Regelungen GmbH.

This especially applies for copies, translations, micro ﬁlms

and the storage into electronic systems. Editor: RESOL -

Elektronische Regelungen GmbH

Important notice:

We took a lot of care with the texts and drawings of this

manual and to the best of our knowledge and consent. As

faults can never be excluded, please note: Your own calcu-

lations and plans, under consideration of the current stan-

dards and DIN-directions should only be basis for your

projects. We don´t offer a guarantee for the completeness

of the drawings and texts of this manual - they only repre-

sent some examples. They can only be used at your own

risk. No liability is assumed for incorrect, incomplete or

false information and the resulting damages.

Errors an technical changes excepted.

Resol Calvio Owner's manual

Resol Calvio Owner's manual

Resol Calvio Owner's manual

Related papers

Other documents