Furuno FAR-2157 User manual

Category
Radar detectors
Type
User manual

This manual is also suitable for

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
www.furuno.co.jp
MARINE RADAR
FAR-2157/2157-BB/2157-D
Installation manual
SAFETY INSTRUCTIONS....................... i
SYSTEM CONFIGURATION ................. iii
EQUIPMENT LISTS .............................. iv
1. MOUNTING ..................................... 1-1
1.1 Antenna Unit ........................................ 1-1
1.2 Monitor Unit.......................................... 1-7
1.3 Control Unit ........................................ 1-10
1.4 Processor Unit .................................. 1-15
1.5 Power Supply Unit ............................ 1-16
2. WIRING ........................................... 2-1
2.1 Wiring Overview................................... 2-1
2.2 Antenna Unit ........................................ 2-2
2.3 Monitor Unit (for FAR-2157)................. 2-8
2.4 Processor Unit ..................................... 2-9
2.5 Power Supply Unit ............................. 2-14
2.6 Changing AC Power Specification ..... 2-16
3. ADJUSTMENT ................................ 3-1
3.1 Initializing tuning .................................. 3-1
3.2 Heading Alignment............................... 3-3
3.3 Adjustment Sweep Timing.................... 3-5
3.4 Suppressing Main Bang ....................... 3-6
3.5 Other Settings ...................................... 3-7
4. OPTIONAL EQUIPMENT ................4-1
4.1 Gyro Converter GC-10 ......................... 4-1
4.2 Memory Card Interface Unit ............... 4-10
4.3 DVI-RGB Conversion Kit.................... 4-13
4.4 BNC Connector Converter ................. 4-16
5. IO DATA...........................................5-1
PACKING LISTS ................................ A-1
OTLINE DRAWINGS .......................... D-1
INTERCONNECTION DIAGRAM ....... S-1
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone : +81-(0)798-65-2111
Fax
:
+81-(0)798-65-4200
A : FEB 2007
.
Printed in Japan
All rights reserved.
E : FEB . 10, 2011
Pub. No. IME-35220-E
*00014869214**00014869214*
(HIMA ) FAR-2157/BB
*
00014869214
*
*
00014869214
*
* 0 0 0 1 4 8 6 9 2 1 4 *
i
WARNING
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Warning, Caution
Mandatory Action
Prohibitive Action
SAFETY INSTRUCTIONS
T
he installer must read and follow all the safety instructions before attempting to install the
e
quipment.
WARNING
The radar antenna emits electromagnetic radio frequency (RF) energy which can
be harmful, particularly to your eyes. Never look directly into the antenna aperture
from a close distance while the radar is in operation or expose yourself to the
transmitting antenna at a close distance.
Distances at which RF radiation levels of 100 W/m
2
and 10 W/m
2
exist are given in
the table below.
Note: If the antenna unit is installed at a close distance in front of the wheel house
,
it may be necessary to halt transmission within a certain sector of antenna
revolution. This can be done from the SCANNER menu.
XN4A
XN5A
Radiator
type
Distance to
100 W/m
2
point
Distance to
10 W/m
2
point
1.20 m
1.10 m
13.60 m
12.30 m
Radio Frequency Radiation Hazard
ii
WARNING
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
Only qualified personnel should work
inside the equipment.
Wear a hard hat and safety belt when
mounting the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna mast.
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna
mast.
Do not install units other than the
antenna unit in a place subject to rain
or water splash.
Fire, electrical shock or injury can result if
water leaks into those units.
Turn off the power at the switchboard
before beginning the installation.
Fire, electrical shock or injury can result if
the power is on during the installation.
Use only the specified power cables.
Use of power cables that are thinner than
those specified can cause fire.
Securely attach protective earth to the
ship's body.
The protective earth is required to prevent
electrical shock.
A proper license is necessary to install
a radar.
See your dealer for details.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
CAUTION
Antenna Unit
(60 kw)
Standard
compass
Monitor Unit
(MU-201CR)
1.55 m 1.00 m
Processor Unit
(RPU-013)
1.35 m 0.85 m
Control Unit
(RCU-014)
0.30 m 0.30 m
Control Unit
(RCU-015)
0.95 m 0.60 m
Control Unit
(RCU-016)
0.65 m 0.45 m
Power Supply
Unit (PSU-006)
Memory Card
Interface Unit
(CU-200)
0.90 m 0.60 m
Steering
compass
4.30 m 2.80 m
0.30 m 0.30 m
Switching Hub
(HUB-100)
1.00 m 0.60 m
Monitor Unit
(MU-190
)
1.65 m
1.05 m
iii
SYSTEM CONFIGURATION
PROCESSOR
UNIT
RPU-013
Navigator
IEC-61162 Serial data
(I/O)
IEC-61162 Serial data
(Input)
Speed Log
Gyrocompass
AIS
Track Controller
: Optional supply
: Local supply
: Standard supply
100-115 VAC/
220-230 VAC
1f, 50/60 Hz
AD-100
MEMORY CARD
INTERFACE UNIT
CU-200-FAR
VDR
External
Monitor
Radar Remote
Display
Alarm
MONITOR UNIT
MU-201CR
(For FAR-2157)
MU-190
(For FAR-2157-D)
CONTROL UNIT
RCU-014
(Standard)
OR
RCU-015
(Trackball)
CONTROL UNIT
RCU-016
TRANSFORMER
RU-1803
440 VAC
1f, 50/60 Hz
GYRO CONVERTER
GC-10
100-230 VAC
1f, 50/60 Hz
ANTENNA UNIT
XN4A-RSB-106
XN4A-RSB-107
XN5A-RSB-106
XN5A-RSB-107
SWITCHING HUB
HUB-100
Equipment category
Unit
Antenna
Other units
Category
Exposed to weather
Protected from weather
POWER SUPPLY UNIT
PSU-006
100-115V/220-230 VAC
1f, 50/60 Hz
TRANSFORMER
RU-1803
440 VAC, 1f,
50/60 Hz
110 VAC, 3f, 60 Hz
220 VAC, 3f, 50 Hz
440 VAC, 3f, 50 Hz
(For antenna motor)
(For HV power)
200 VAC, 3f, 50 Hz
220 VAC, 3f, 60 Hz
TRANSFORMER
RU-5693
TRANSFORMER
RU-6522
TRANSFORMER
RU-5466-1
RECTIFIER
RU-3423
100/110/115/220/230 VAC
1f, 50/60 Hz
24 VDC
*
* FAR-2157-BB is not equipped with a
monitor unit. Procure one locally.
iv
EQUIPMENT LISTS
Standard supply
* See packing list at end of this manual.
Optional equipment
Name Type Code No. Qty Remarks
Antenna Unit XN4A-RSB-106 –
1
200/220 VAC, 2570 mm
XN4A-RSB-107 – 24 VDC, 2570 mm
XN5A-RSB-106 – 200/220 VAC, 3210 mm
XN5A-RSB-107 – 24 VDC, 3210 mm
Power Supply Unit PSU-006 – 1
Monitor Unit MU-201CR – 1 For FAR-2157
MU-190 – For FAR-2157-D
Processor Unit RPU-013 – 1
Control Unit RCU-014 –
1
Standard type
RCU-015 – Trackball type
Installation
Materials*
CP03-31301 008-572-970 1 For antenna unit
CP03-25700 000-080-435
1
15 m signal cable (RW-9600)
CP03-25710 000-080-436 30 m signal cable (RW-9600)
CP03-25730 000-082-191 40 m signal cable (RW-9600)
CP03-25720 000-080-437 50 m signal cable (RW-9600)
CP03-25800 000-080-434 1 Cable assy. for monitor unit
CP03-25602 008-535-940 1 For processor unit
CP03-31401 008-572-750 1 For power supply unit
CP03-25604 008-539-850 1 For control unit
Accessories* FP03-09810 008-536-010 1 For monitor unit
FP03-09850 008-535-610
1
For standard-type control unit
FP03-09860 008-535-690 For trackball-type control unit
Spare Parts* SP03-14404 008-535-910
1
For processor unit, 100 VAC
SP03-14405 008-535-920 For processor unit, 220 VAC
SP03-09203 008-424-380 1 For 24 VDC antenna unit
SP03-14401 008-535-990 1 For FAR-2157's monitor unit
SP03-15501 008-572-730
1
For power supply unit, 100 VAC
SP03-15501 008-572-740 For power supply unit, 220 VAC
Name Type Code No. Remarks
Gyro Converter GC-10-2 000-080-440 See Chapter 4.
Rectifier Unit RU-3423 – 100/110/115/220/230 VAC to 24 DC,
for power supply unit
(Continued on the next page.)
v
Stepdown
Transformer
Unit
RU-1803 – 440 to 100 VAC, for processor unit
RU-5693 – 110 to 220 VAC, 3φ, for antenna unit
RU-6522 – 220 to 200 VAC, 3φ, for antenna unit
RU-5466-1 – 440 to 200 VAC, 3φ, for antenna unit
Memory Card
Interface Unit
CU-200-FAR 000-081-568 w/CP03-27430, see Chapter 4.
External Alarm
Buzzer
OP03-21 000-030-097
Control Unit RCU-016 000-080-299 Remote type, w/FP03-09860
RAM Card O0RAM08MC-005 004-376-740 8MB
DVI-RGB
Converter Kit
OP03-180-1 008-545-590 For installation in the field.
OP03-180-2 008-536-070 For installation in field. See Ch. 4.
Cable Assy. XH10P-W-6P L=20M 000-149-748
Processor unit
QControl unit, 20 m
XH10P-W-6P L=30M 000-149-749
Processor unit
QControl unit, 30 m
XH10P-W-5P-A L=10M 000-149-050 Between control units, 10 m
XH10P-W-5P-A L=20M 000-149-051 Between control units, 20 m
XH10P-W-5P-A L=30M 000-149-052 Between control units, 30 m
DVI-D/D S-LINK 10M 000-150-200
Processor unit
QControl unit, 10 m
S03-9-5(8-8P) 008-206-640 External radar, 5 m, 8-8P
S03-9-10(8-8P) 008-206-650 External radar, 10 m, 8-8P
S03-9-15(8-8P) 008-209-160 External radar, 15 m, 8-8P
Installation
Materials
(Armored LAN-
Cable Kit)
CP03-28900 000-082-658 FR-FTPC-CY 10 m, modular
connector MPS588-C, 2 pcs.
CP03-28910 000-082-659 FR-FTPC-CY 20 m, modular
connector MPS588-C, 2 pcs.
CP03-28920 000-082-660 FR-FTPC-CY 30 m, modular
connector MPS588-C, 2 pcs.
Bracket Assy. FP03-09820 008-535-560 Hanger assy. for monitor unit
Handgrip Assy. FP03-09840 008-535-570 For monitor unit
Dust Cover 03-163-1201 100-307-260 For monitor unit
Clamp Assy. OP03-182 008-535-620 For RCU-014
Flush Mount Kit FP03-09870 008-535-630 For control unit
OP03-198 001-008-050
Connection
Stand
OP03-183 008-535-640
RCU-014
QMU-201CR
OP03-185 008-535-660 RCU-014
Hanger Kit FP03-10201 008-539-530 Desktop inst. kit for CU-200-FAR
BNC
Connector
Converter
DSUB-BNC-1 000-148-528 For connecting VDR
Switching Hub HUB-100 – See Operator's Manual for HUB-100,
issued separately.
Hood FP03-11500 001-020-090 For MU-201CR display unit
Slim Hood FP03-11510 001-034-390 For MU-201CR display unit
Name Type Code No. Remarks
vi
This page is intentionally left blank.
1-1
1. MOUNTING
1.1 Antenna Unit
Mounting considerations
The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on
a suitable platform. The mounting location should afford a good all-round view and satisfy the
siting and mounting considerations mentioned below.
Siting
• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow
direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar
picture.
• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial perfor-
mance and hot gases may deform the radiator. The antenna unit must not be mounted where
the temperature is more than 70°C.
• Locate a direction finder antenna clear of the antenna unit to prevent interference to the direc-
tion finder. A separation of more than two meters is recommended.
• Choose a location where reflections from the radar reflector will not be received by the radar
antenna.
• The "standard" antenna unit orientation has the cable glands directed toward the bow.
• Leave sufficient space around the unit for maintenance and servicing. See the antenna unit out-
line drawing for recommended maintenance space.
Mounting
• Use rope and crane to hoist the antenna unit to the mounting location. Lifting fixtures are pro-
vided on the antenna chassis to which to fasten rope.
• Mount the unit parallel to the waterline.
• A hole is required in the mounting platform for the antenna cable.
• An appropriate platform should be constructed at the mounting location to facilitate installation
and maintenance work.
• Connect ground wire between antenna terminal on antenna chassis and ground point.
• If the mounting platform is made of steel paint it to prevent electrolytic corrosion. DO NOT paint
the antenna radiator.
NOTICE
Do not apply paint, anti-corrosive sealant
or contact spray to coating or plastic
parts of the equipment.
Those items contain organic solvents that
can damage coating and plastic parts,
especially plastic connectors.
1-2
Assembling the antenna unit
The antenna unit should be assembled before mounting it. Follow the procedure below to
assemble the antenna unit. The numbers in parentheses refer to the parts numbers shown in the
illustration on the next page.
1. Grease the O-ring(1) and set it to the O-ring groove in the flange on the rotation coupler on the
antenna base. Fasten the feeder waveguide to the antenna base with hex bolts B(2). Coat the
surface of the waveguide flange with silicon rubber, referring to the illustration below for instruc-
tions.
2. Loosely fasten the antenna radiator to the antenna base with hex bolts(3) and(6), flat
washers(5) and (7), spring washers(4) and (8) and hex nut(9).
3. Grease the O-ring(1) for the antenna radiator and set it to the O-ring groove on the feeder
waveguide flange on the antenna radiator. Fasten the feeder waveguide to the antenna radiator
with hex head bolts(2).
4. Fasten the waveguide clamp(13) to the waveguide clamp insulator(14) with hex head bolt(10),
flat washer(12) and spring washer(11).
5. Securely fasten the antenna radiator to the antenna base.
How to coat waveguide flange with silicon rubber
How to coat waveguide flange with silicon rubber
Choke guide
O-ring
O-ring
Silicon
rubber
Silicon rubber
(1) Do not let sealant contact O-ring groove.
(2) Evenly coat flange with silicon rubber at the locations shown
below.
Use enough silicon rubber so that it oozes out when
fastening bolts. Wipe off surplus. Be sure silicon rubber
does not contact choke guide or feeder waveguide.
Note: The surface to be coated with silicon rubber should be
cleaned beforehand to remove foreign material or silicon
rubber previously applied.
1-3
Parts of antenna unit XN4A/XN5A
List of parts for assembling antenna unit
No. Name Type Qty
1 O-ring AS568-125 2
2Hex Bolt B
M4
×16 (SUS304)
8
3Hex Bolt
Antenna unit XN4A: M8
×25 (SUS304)
4
Antenna unit XN5A: M8
×35 (SUS304)
4 Spring Washer M8 (SUS304) 4
5 Flat Washer M8 (SUS304) 4
6Hex Bolt
M8
×30 (SUS304)
4
7 Flat Washer M8 (SUS304) 8
8 Spring Washer M8 (SUS304) 4
9 Hex Nut M8 (SUS304) 4
10 Hex Bolt
M4
×30 (SUS304)
2
11 Spring Washer M4 (SUS304) 2
12 Flat Washer M4 (SUS304) 2
13 Waveguide Clamp RSB-2006-2 1
14 Waveguide Clamp Insulator 03-003-4003-0 1
Chemiseal S-8400W, aluminum tube, 50g 1
Antenna Radiator
Feeder Waveguide
Antenna Base
Rotation Coupler
1-4
How to hoist antenna unit
1. Referring to the illustration below, fasten rope A of approx. 85 cm in length and fasten rope B
of approx. 100 cm in length.
2. Place protective material (cardboard, foam, etc.) between rope and radiator at the asterisk-
marked locations shown below, to prevent damage to the radiator.
3. Hoist the antenna slightly and confirm that the load applied to the radiator is not excessive. (If
load is excessive, lower the antenna unit and adjust lengths of ropes.)
4. Hoist the antenna unit to the mounting location.
How to attach hoisting ropes to antenna unit
A
B
1-5
Fastening antenna unit to the mounting platform
Note: The antenna unit is made of cast aluminum, which is subject to electrolytic corrosion if the
mounting platform is steel or iron. To prevent electrolytic corrosion, use the supplied seal washers
and corrosion-proof rubber mat.
Fix the antenna unit to the mounting location, referring to the procedure below and the illustration
on the next page.
1. Referring to the antenna unit outline drawing, prepare a mounting platform at the mounting
location for the antenna unit.
2. Lay the corrosion-proof rubber mat (supplied) on the mounting platform, aligning the holes on
the rubber mat with the fixing holes on the mounting platform.
3. Lay the antenna unit on the rubber mat, orienting it so the cable gland is directed toward ship's
bow.
4. Use hex bolts (M12×60), nuts, flat washers and seal washers to fix the antenna unit to the
mounting platform.
5. Arrange the ground point at a location on the mounting platform that is within 300 mm from the
ground terminal on the antenna unit. Fasten the ground wire (RW-4747, 340 mm) there, using
the M6×25 hex bolt, nut and washers.
6. Connect the other end of the ground wire to the ground terminal on the antenna unit.
7. Coat the ground terminal, ground point on the mounting platform and fixing bolts on the
antenna unit with anticorrosive sealant (supplied).
WARNING
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
Only qualified personnel should
work inside the equipment.
Wear a hard hat and safety belt when
mounting the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna mas
t.
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna
mast.
1-6
How to mount the antenna unit
Seal washer
Corrosion-
proof rubber
mat
Hex bolt
Hex nut
Spring washer
Spring washer
Ground
wire
Flat washer
Hex bolt
Hex nut
Spring washer
Flat washer
Ground
wire
Lay rubber mat, fix
antenna with bolts, nuts
and seal washers.
Coat with anticorrosive
sealant.
Ground wire
Ground terminal is provided
on antenna unit.
Anticorrosive
sealant
Coat with
anticorrosive sealant.
1-7
1.2 Monitor Unit
The monitor unit is can flush mounted in a panel or mounted on a desktop (requires optional
accessories).
The FAR-2157-BB is not equipped with a monitor unit. Procure a suitable monitor unit locally. Rec-
ommended monitor: SXGA (1280×1024), aspect ratio 5:4.
For MU-190, see the applicable Operator’s Manual.
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Select a location where the screen can be viewed conveniently while facing the bow.
• Locate the unit out of direct sunlight and away from heat sources because of heat that can build
up inside the cabinet.
• Locate the unit away from places subject to water splash and rain.
• Leave sufficient space on the sides and rear of the unit to facilitate maintenance, referring to the
outline drawing for maintenance space.
• The monitor unit will give interference to a magnetic compass if it is placed too close to the com-
pass. Observe the compass safe distances on page ii to prevent interference to the compass.
Mounting procedure
Flush mounting
Follow the procedure below to mount the monitor unit in a console.
1. Make a cutout in the mounting location referring to the outline drawing shown below.
2. Set the monitor unit to the hole and fix it with four self-tapping screws (6×30).
3. Attach panel hooks near the fixing holes (upper part). See next page. These are used to pull
out the monitor unit from the panel for servicing.
4. Attach four panel covers to the fixing holes.
Mounting dimensions for flush mounting the monitor unit
(79)
454
506
534
4-φ8
FIXING HOLES
490
420
4-FIXING HOLES
30
80
506 1
296
1
1
296
1
1-8
How to attach panel hook and panel cover
Note: If you need to remove the monitor unit from the console, remove the four panel covers with
your fingernail and use two panel hooks supplied as accessories to lift the monitor unit.
Desktop mounting
Use the optional desktop mouting kit (Type: FP03-09820, Code No.: 008-535-560) to mount the
monitor unit on a desktop.
1. Assemble two hangers and hanger stay with two hex bolts (M10×30), flat washers and spring
washers and cover each hex bolt with hole plug.
2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard supply).
3. Fasten the monitor unit to the mounting hanger assembly with four hex bolts (M6×25, supplied).
4. Cover each hex bolt with a panel cover (4 pcs.).
5. Cover fixing holes for hand grips with snap buttons (4 pcs).
Contents of desktop mounting kit FP03-0982
0
Name Type Code No. Qty
Hanger L 03-163-1111 100-305-141 1
Hanger R 03-163-1112 100-305-181 1
Hanger stay 03-163-1113 100-305-191 1
Hole plug CP-30-HP-13 000-160-074-10 2
Snap button KB-13, Black 000-570-276-10 4
Hex. bolt
M6
×25
000-162-949-10 4
Hex. bolt
M10
×30
000-162-884-10 2
Spring washer M10 000-864-261 2
Flat washer M10 000-864-131 2
Panel hook
Panel cov
er
Fixing screw
1-9
Fastening monitor unit to hanger
Attaching hand grips
Hand grips are optionally available for the desktop-mount monitor unit. Attach them as follows:
1. Remove the snap buttons attached at step 5 on the previous page.
2. Fix hand grips with wave washers, rosette washers and flat head screws.
How to attach hand grips
Attaching hood
When it is too bright in the daytime, use the optional hood (Type: FP03-11500, Code No.: 001-
020-090) to shade the screen.
Contents of hood
Name Type Code No. Qty.
Hood FP03-11501 001-020-120 1
Fixing plate 03-163-2202-0 100-335-560-10 4
Screw M4x10 D=13 US304 000-862-543 4
Panel cover
Hex bolt
(M6x25)
Hanger (R)
Hanger stay
M12 bolts for fixing
(Dockyard supply)
Hanger (L)
Hex bolt
M10x30
Snap button
Hole plug
Panel cover
To remove this, insert fingernail in groove.
Flat Washer M10
Spring Washer M10
Hand grip
Flat head screw (torque: 7.6 Nm)
Wave washer
Rosette washer
1-10
1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts (sup-
plied).
Flush mounting: Fasten the display unit to the mounting location, and then attach the fixing
plates with four self-tapping screws.
2. Attach the hood to the display unit (the hood is outside of the fixing plates).
3. Fasten the hood to the fixing plates with four screws supplied (M4x10).
1.3 Control Unit
Mounting considerations
The control unit may be mounted on a desktop, with or without the KB fixing metal (supplied) which
mounts the control unit at an angle. When selecting a mounting location, keep in mind the fol-
lowing points:
• Select a location where the control unit can be operated conveniently while observing the dis-
play screen.
• Locate the unit away from heat sources because of heat that can build up inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Determine the mounting location considering the length of the signal cable between the control
unit and the processor unit. (A 10 m signal cable is attached to the control unit.)
• A magnetic compass will be affected if the control unit is placed too close to it. Observe the com-
pass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Fixing with KB (keyboard) fixing plate
The KB fixing plate sits the control unit at a comfortable angle, like the retractable legs on a PC
keyboard.
1. Fix the KB fixing plate to the bottom of the control unit.
2. Attach cushions (three for RCU-014, two for RCU-015/RCU-016) to the bottom of the control
unit as shown below.
3. Fix the unit to a desired location with self-tapping screws (local supply).
Control unit RCU-014/015/016, side view
Fixing plate
Fixing hole
Hex head bolt
Cushio
n
KB fixing plate
1-11
Fixing without KB fixing plate
1. Drill four mounting holes of 5 mm diameter, referring to the outline drawing at the back of this
manual.
2. Fix the control unit with four screws (M4) from the under side of the desktop. (M4 screws with
a sufficient length for the thickness of the desktop should be provided locally.)
Mounting dimensions for control unit RCU-014
Mounting dimensions for control unit RCU-015/RCU-016
#70
308±1
398
136±1
180
4-M4 (Fixing holes
)
(bottom)
# Minimum recommended service space
F4
F3
F2
F1
180
24 32
110±1
160
136±1
4-M4 (Fixing holes)
(REAR)
1-12
Flush mounting
Use the optional flush mount kit FP03-09870 (Code No. 008-535-630) to flush mount the control
unit RCU-014, RCU-015 and/or RCU016 in a console.
1. Prepare a cutout in the mounting location as shown in the figure below.
Flush mount cutout for RCU-014 Flush mount cutout for RCU-015 and RCU-016
2. Set the control unit to the cutout.
3. From the rear side, attach the mounting plate to the control unit with four screws.
4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing screw.
5. Fasten each wing screw and then fasten the hex nuts as shown in the figure below.
Flush mount mounting dimensions for control unit RCU-014 (left) and RCU-015/RCU-016
Contents of flush mount kit for RCU-014/015/016
Name Type Qty
Mounting plate 03-163-7531 4
Hex bolt M5 4
Wing screw
M5
×40
4
Pan head screw
M4
×12
4
388 150±2
170±2 176±2
±2
(P)
#70
53
92
(P)
#70
171
53
86
Note: P 10
<
=
# Minimum recommended service space
To change location of
cable entrance, see
page 1-14.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111

Furuno FAR-2157 User manual

Category
Radar detectors
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI