Samsung SADPCI-202 User manual

Brand: Samsung

Model: SADPCI-202

Category: Receiver

Type: User manual

Instruction manual

SADPCI-202

Digital Satellite Receiver

Table of Contents

1. Safety and precautions 2

2. Accessories 3

3. System Connection 4

4. Front Panel 5

5. Rear Panel 6

6. Remote Control Unit 7

7. Quick Start 8

8. Downloading Channels 9

9. Viewing your channels 10

10. Multi-satellite 10

11. Favourite Channels 11

12. Electronic Programme Guide(EPG) 11

13. Selecting different audio channels 12

14. Additional Information 13

15. Parental Control 14

16. Parental Lock 14

17. Advanced users guide 16

18. Tuning Modes 17

19. Setup Satellite 18

20. Editing Channels 19

21. Arrange 19

22. Sort Free to Air Channels 20

23. Deleting Channels 21

24. Installation 22

LNB

TV/VCR settings

Preferences

Set local time

System Information

25. Reset to factory defaults 25

26. Trouble shooting 26

27 . Analogue option 27

28. Using the analogue option 28

29. Positioner model 32

30. Channel Listing 34

31. Audio Table 45

32. Common Interface 46

33. Common Interface(option) 47

34. Technical Specifications 48

Safety and Precautions:

Thank you for purchasing the new SAMSUNG digital satellite receiver. For your safety and proper

operation of your receiver, please take time reading this manual fully before installing and operating

the receiver.

Safety notice:

DANGER! HIGH VOLTAGE! RISK OF ELECTRIC SHOCK!

Lethal voltages are present inside the unit. Always unplug the receiver completely from mains outlet

before connecting or disconnecting anything.

No user-serviceable parts inside. Please refer all servicing to qualified service agents.

Never expose the unit to water, moisture, extreme cold or direct sunlight.

Slots are provided for proper ventilation for the unit, do not obstruct them.

Do not insert or drop small objects into the unit.

Install the unit in a well-ventilated location

Never cover the unit or operate the unit near any heat source.

It is advisable to unplug the unit from the mains, TV, and the satellite dish when a thunderstorm is

expected.

Cleaning your receiver

Always unplug the unit from mains before cleaning the unit.

Do not use solvents of any kind to clean the unit, only use a soft-dry cloth.

SAMSUNG reserves the right to change specifications without prior notice.

This manual only covers the version of software supplied with the receiver.

Accessories:

User Manual: 1

Batteries: 2

UHF TV cable: 1

Remote Control Unit: 1

SIGNAL

F2F1 HELP

5 6

INFOTV

VOL

C H

ESC

VOL

MUTE

C H

RADIO LANG

TV SAT

System Connection:

Please unplug all unites from mains outlet before installation. Once all connections are made please

check again before connecting the equipment to the mains outlet.

The following shows a typical installation of a satellite receiver. If you require further assistance for the

installation of your satellite receiver, please contact your local distributor.

Front Panel:

A. Standby: To switch the receiver on / off.

B. Menu: To enter the main menu.

C. Volume +/-: To increase or decrease volume level.

D. Exit: To back step or exit from menu.

E. Display: Displays channel mode and channel number (see below*).

F. Channel +/-: To change channels or move cursor in menu.

* Display modes:

The current viewing mode is displayed by your receiver:

Mode: Menu info bar: Front panel LED display:

TV TV icon + Channel. No. Channel Number

Radio Radio icon + Channel No. r + Channel No.

Favourites Heart icon + Channel No. F + Channel No.

B C D

Rear Panel:

Please refer to the diagram above for all the connection possibilities of your receiver. Do not connect

the unit to the mains socket until all other connections have been made and checked.

IF Input: Connect the cable from your dish to this connector.

Loop Out: If you have a second satellite receiver, connect the second satellite receiver’s

LNB input to this connector.

TV: Connect your TV UHF input to this connector.

ANT: Connect your TV antenna to this connector-only in

conjunction with TV UHF output.

TV SCART: Use this connector to connect you TV to the receiver via a SCART cable.

VCR SCART: Use this connector to connect you VCR to the receiver via a SCART cable.

Video: Composite video output for connecting to a monitor etc.

0/12V: 0 or 12V output for external control switch.

Audio L/R: Audio outputs for connecting to an external stereo amplifier.

S-Video Out: Additional output for recording with a VCR / camcorder with S-ideo capability.

RS232: You can connect the receiver to a PC via this connector (advanced users only).

IEEE 1284: High-speed data port for connecting with a PC (advance users only).

Once ALL the connections are made and CHECKED, you may connect the unit to the main

supply.

Remote Control Unit:

By-Pass SCART priority

VCR loop through

To switch to the second

Soundtrack/ language

To display channel status or

current or next channel

information in EPG mode

To mute the sound

To change channels in view

mode, or to move cursor up or

down in menu mode

To about setting or to back out or

of menu

Numeric Keys : Used to select

channels or enter programming

parameters

Function keys :

In normal viewing mode, F1 may

be used to recall the last viewed

channel

Additional functions will be

indicated in menus where

applicable

Display TV channel list

Programme Guide :

To display the current and next

programme information

(if available)

Toggle signal meter

Display radio channel list

To edit or display the Favourite

channels list

To Display the on-line help

messages when available

To select menu option, or to

updated on entry

To change volume, or to move

cursor left, right in menu

To switch your receiver on from

stand by or off to stand by

SIGN

F2F1

HEL

VOL

C H

VOL

DIO

SAT

LANG

SCAN

INDEX

BLUE

POS

A/D

Quick Start:

After initialisation, the Language selection screen will be displayed.

By using the LEFT/RIGHT keys, you may select the

different menu languages available. Once you have

selected the desired menu language, press OK to

continue with set-up.

After selecting the menu language, the receiver will display the Channel Tuning Menu:

(Menu, Channel Setup, OK)

Preset Entry:

Move the cursor to highlight the “Satellite” box and

use the LEFT/RIGHT keys to scroll through the pre-

stored satellites. For example, if your dish is aimed

at the Astra satellite, when Astra is selected, you

should see both signal meters reading a good signal

level. The receiver will then prompt you to press OK

to start tuning to all the channels on Astra.

(See next page)

Note:

1. If you wish to only tune to a specific Network or Bouquet of channels, move the cursor to highlight

the “Bouquet” box and use the LEFT/RIGHT keys to scroll through the pre-stored Bouquets. You

should now see both signal meters reading a good signal level and the receiver will prompt you to

press OK to start tuning all the channels from the selected Network or Bouquet.

2. If you only wish to download Free-to-Air channels, high-light the FTA box and turn the option to “on”.

Provided your dish is installed correctly and aligned to the relevant satellite, both the Signal and Data

bars should display a GREEN bar which denotes the following:

The first bar shows the actual satellite SIGNAL strength

You should see a GREEN bar showing your satellite signal is medium to good. If it is RED, this

normally indicates that either your dish/LNB set-up is not adequate for this satellite, or your dish is

not correctly aligned.

The second bar shows the quality of the DATA received

This GREEN bar indicates the DATA INTEGRITY of the signal received. If the bar is RED, this

indicates that the DATA received is unreliable. This could cause the picture to break up, or

disappear completely.

Note: If “No signal found” is displayed, check that the values entered are correct and are valid for

the satellite your dish is installed for. (Please also refer to the “Advanced Users” and “Trouble

Shooting” section to check that your LNB settings are correct).

Manual Entry (see also “Advanced User Guide” ):

(See the “Advanced User Guide” section for more information on manual entry and other tuning

options other than Auto set-up.)

Select Menu Language

LNB

Preset

Satellite

Frequency

Sym. Rate

Polarity

FEC

Setup Satellite

11720

27500

Hor 18v

3/4

Network Bouquet PIDs

FTA

Off

Signal

Data

Snaigl Found

Use to change Satellite

F1 – Preset F2 Mode

English

Hotbird – 13.0E

Downloading Channels:

With a “Signal Found” message displayed the signal meters in the Channel Tuning Menu,and

depending on whether you have selected a Satellite or Bouquet search.

Press the OK key to begin auto search (Satellite, Network or Bouquet).

The AUTO CHANNEL SEARCH screen will now be displayed:

Please wait for the receiver to process all the channels - this may take a few minutes. The time

required to tune in all the channels on the selected satellite depends on the number of channels

available. You may press the ESC key to stop auto tuning anytime.

All the channels found (TV and Radio) will be displayed in the two separate boxes provided in the

“Auto Channel Search” menu. Once all the channels are found, the “Finished” message will be

displayed at the bottom of the menu indicating that the process has finished.

Now press the OK key to store the new channels.

You should now be able to view the first channel found by your receiver. The channel number, channel

information and the clock will be displayed at the top of the screen for a few seconds. You may recall

this information banner by pressing the INFO key on your handset.

Note: Some channels are scrambled - only channel information will be displayed.

You may now either go and view your downloaded channels or continue to download channels from

another bouquet or satellite.

uto

hannel

earch

TV channels Radio channels

Searching 11.381 GHz

A uto Channel Search

TV channels Radio channels

Searching 11.381 GHz …

Sky 1

CNN

NBC

Movies 1

Sky news

BBC1

Virgin Radio

ITN

89 17

Astra 19.2E

Viewing your channels:

There are several ways to access the stored channels:

Using the UP/DOWN keys on the remote handset to access the channels sequentially.

Using the numeric keys (0-9) by typing the channel number to access the channels directly.

Using the TV key on your handset to display the TV channel list. Use the UP/DOWN keys to

move the cursor to highlight the desired channel, then press OK to view that channel. You may

also use the LEFT/RIGHT keys to skip to the next or previous page of the channel list for quicker

scrolling.

¶ Using the “Favourite Channels List” - You may add all your favourite TV and Radio channels

into the “Favourite Channels List”. Please see next section on instructions for using and editing

favourite channels.

Multi-satellite:

As you download channels from different satellites, your digital satellite receiver will store in dedicated

satellite groups. For more details please refer to the Advanced User Guide.

List by satellite:

To access your channels, press the TV (or Radio) key:

To access the list of channels on a different satellite,

press F1 or F2 keys. Within each list you may use

the Up/Down, Left/Right keys to highlight the required

channel and press OK to select it.

List in Alphabetical order:

Alternatively, from View mode you can list all the stored

channels in alphabetical order by pressing TV (or Radio)

twice in succession.

Use the Up/Down, Left/Right keys to highlight the

channels and press OK to select it. In alpha mode,

you can also use the F1/F2 keys to skip to the next

letter to save time.

Note: At any time if you wish to return to your original cursor position, simply press the HELP

key on your remote.

2 Sky

3 Cartoon

4 TNT

5 CNBC

6 STAR TV1

7 MTV

8 VH-1

1 CNN

Astra 19.2E

Use to move

cursor

Use OK to select

Press ESC to exit

Astra 19.2E

Canal +11 TV14

Canal +2 TV17

CNBC TV22

CNN TV18

Fashion TV35

K1 TV57

K2 TV60

K3 TV54

Use to change

page

Favourite Channels:

Before you can use the “Favourite Channels List”, you must first add your favourite channels into the

favourites list. Please refer to the instructions below:

1. In view mode press the TV button to display the TV channel list.

2. You will now see the TV listing with your current channel highlighted.

3. Press the FAVOURITES key (heart shape) to add a favourite icon next to the channel name. This

channel will be added to the “Favourites List”. To add more channels to your “Favourites List” move

the cursor to highlight another channel and press

the FAVOURITES key. (if you press the FAVOURITES

key again it will remove the favourite icon).

4. Press the OK key to store the favourite settings.

In view mode press the FAVOURITES key to display

the “Favourite Channel List”.

To view your favourite channel, highlight it and press OK.

Electronic programme guide (EPG):

This receiver is equipped with a unique dual EPG system which gives you two easy ways to view the

programme information (what’s on now and what’s on next)! When transmitted by the broadcaster, the

EPG system can display a variety of programme information ranging from start and end times of a

programme to additional information about the programme itself. You can easily select and view a

programme on the EPG by highlighting it and pressing OK.

You can also choose between a FULL or

CONDENSED version of the EPG, using

the “Preferences” section under

the Installation Menu:

Full EPG

1 Discovery

Select Menu Language

EPG Type

Default Audio Language

Menu Transparency

English

Full

eng

TV Guide (Current Prog. Info.)

Channel 1 of 124 Time :

Press EPG key for current/next prog. Info.

Use INFO key for more information

CNN International Regional financial report

12:30 – 13:00

Eurosport CART Indy Car series

12:00 – 14:00 8

Round Detroit GP

Sci-fi Channel Wonder Woman

12:30 – 13:00

NBC Europe No Info.

12:30 – 12:45

12:35

Channel Time: 3 Scheduled

Press EPG key for current/next prog. Info.

Use INFO key for more information

TV Guide (Current Prog. Info.)

2. Eurosport 12:00 – 14:00

3. Sci-fi Channel 12:30 – 13:00

4. NBC Europe 12:30 – 12:45

5. Canal+ Swe 12:30 – 13:45

Regional financial report

1. CNN International 12:30 – 13:00

Astra 19.2E

Canal +11 TV14

Canal +2 TV17

CNBC TV22

CNN TV18

Fashion TV35

K1 TV57

K2 TV60

K3 TV54

Condensed EPG

Selecting different audio channels:

In digital satellite broadcasts, multiple audio languages can be simultaneously transmitted by the

programme provider.

Default audio setting:

The user can first select a default audio language via the “Preferences” menu for the receiver. Once

the default audio language has been stored, all newly found TV/Radio channels will then be stored

with the selected default audio language.

Multi-Channel Audio:

The broadcasters may transmit more than one language for any channel. By pressing the “LANG” key

on the handset, the user can quickly find out what other languages are available for that channel. If the

left side column of the Audio Control menu shows a selection of different languages, the user can

select and store a new default language for that channel only - for that channel the receiver will always

return to the newly stored default language.

Sometimes two different languages are broadcasted with one language on the Left Audio Channel

(L) and a different language on the Right Audio Channel (R). When this is available, the “Audio

Channel” column of the “Audio Control” menu will display the available audio channels and the user

can then select either channel L or R for the desired language. Otherwise the default L+R setting

would have the two languages “mixed” together and they will be heard at the same time.

From this menu, the left column indicates the

default languages available and the right column

indicates the available audio sub-channels. The

User may then move the cursor to the L or R sub-

channel and listen to decide whether the required

language is available.

Notes:

The left column is the default language setting and this option is storable. If the user changes the

default language to another language, any new programmes which do not support the new default

language may become silent. When this happens, the receiver will display the Missing Audio icon on

the Information Banner, you can press the LANG key to select a different default language.

Many broadcasters transmit multiple languages and programmes on a number of audio sub-channels.

With this menu the user can listen to any of the sub-channels by moving the cursor to highlight them

when available. The L and R audio sub-channels can vary from programme to programme so this is

not stored and will revert to L+R (Stereo) when you change channel.

Language Audio Channel

eng

fra

dan

L+R

Missing Audio icon

Additional Information:

When viewing a programme, pressing the info key will display the information banner.

Note:

If the receiver was previously working on a channel and the “No Signal” icon appears, you may have

one of the following problems:

Signal degraded heavily by poor weather

Channel no longer broadcasting and no carrier

was detected.

Dish not aligned to the correct satellite

LNB power switched off in the menu

Faulty cable or LNB.

The Signal and Data level meter:

Press the Signal key during view mode to display the signal

and data level for the current channel. Use this feature to

assist dish alignment or fault finding should there be a

reception problem.

Diagnostic Information:

For more information on the receiving signal,

press the INFO key to display the diagnostic

Screen:

The diagnostic screen displays detailed broadcast

information in real time. Press INFO key again to

return to the signal meters or ESC to return to the

Picture.

Memory Status:

At any time you can check the memory status on you receiver.

The indicator shows the amount of receiver memory used by the stored channels.

Press:

Menu, Channel Setup, Memory Status:

Memory Used

All channels are stored in memory

Memory Used

Signal

Data

Use INFO key for diagnostic info

Pic. Size: 544x576

Frames/Sec: 25.00

Asp. Ratio: 4:3

Bits/Sec: 15000000

Audio

Channel: Stereo

Emphasis: Off

Sample Rate: 48.00kHz

SAMSUNG

Signal

Data

Video

Parental Control:

To restrict unauthorised access to your receiver, two types of parental lock are provided:

Channel Lock:

This provides channel “lock out” facility to restrict the access of adult programme material.

Menu Lock:

This will lock out the access of both the Channel Tuning and Installation menus from unauthorised

users. This will reinforce the Channel Lock as it also prevents other users from re-tuning channels that

are known to contain adult material.

To access the Parental Control menu:

Press Menu, Parental Lock, OK.

After the correct PIN (Personal Identification Number)

has been entered, the following menu will be displayed:

The default PIN is 0000. If you change your PIN, please

remember to keep it in a safe place.

Channel Lock:

This allows all channel locks to be either enabled or

disabled all at once. First use the Lock/Unlock option

to tag the individual channels to be locked, then

switch the Channel Lock option ON or OFF.

Menu Lock:

This option toggles the menu lock ON or OFF.

When menu lock is ON, you cannot access either

Channel Set-up or Installation menus without

entering a PIN.

Note:

Once the correct PIN has been entered to temporarily

disable a lock, this will remain “unlocked” until the receiver has been switched to standby mode.

Lock/Unlock Channels:

Highlight this option and press OK to display the

Channel Lock menu:-

Use UP/DOWN, LEFT/RIGHT to select the channels you

wish to lock. press F2 to turn the LOCK tag ON and OFF.

Once you have tagged all the channels to be locked,

press ESC to return to the Parental Control menu and

make sure both Channel Lock and Menu Lock are

switched to ON.

Press ESC twice to return to viewing mode and switch the

receiver to Stand-by and back to ON again.

Now go to any Locked Channel (e.g. TNT) and

you will see that this is locked.

To Unlock, press F2 and enter the PIN number and press OK.

P. Lock

Enter Parental Lock PIN :

Channel Lock

Menu Lock

Note: Channel Lock is only effective if

Installation/Channel Setup menus are also

locked with Menu Lock

Lock/Unlock Channels

Change PIN

F2 to Lock/Unlock

SAMSUNG Signal

TV 124 Canal + 19.2E

CHANNEL LOCKED, F2 TO DISABLE LOCK

Astra

Canal +11 TV14 19.2E

Canal+2 TV17 19.2E

CNBC TV22 19.2E

CNN TV18 19.2E

Fashion TV35 19.2E

K1 TV57 19.2E

K2 TV60 19.2E

K3 TV54 19.2E

F2 to Lock/Unlock

OFF

Changing the PIN:

The factory default PIN is set to: 0000. At any time the user may change this PIN code by accessing

the “Change PIN” menu:

To change the PIN code, enter in the new PIN into the New PIN box and re-enter the same PIN again

in the Verify Box to confirm.

If the two PINs are not identical, the change will be aborted and the user will be asked to either re-

enter the new PIN or press ESC to abort the PIN change. If the PIN is accepted this will now be your

new PIN.

Don’t forget your PIN number!

Please write down your PIN code below and keep in a safe place.

If you have forgotten your PIN code, please call an Authorised Service Agent.

Factory PIN Code:

0 0 0 0

New PIN Code:

Please keep this section or this manual in a safe place.

Enter new PIN:

Confirm:

Channel Lock

Menu Lock

Note: Channel Lock is only effective if

Installation/Channel Setup menus are also

locked with Menu Lock

Change PIN

Lock/Unlock Channels

OFF

Advanced users guide:

Tuning to different channel frequencies:

If the satellite you desire is not in the Preset listing, or you want to tune the receiver to a different set of

channels, please follow the instructions below:

To access the tuning menu, press the Menu key:

Move the cursor to Channel Setup and press OK.

Press OK on Tuning to access the Tuning Menu

Press F1 to enter the Manual Tuning Menu.

By referring to your channel listings, enter the

Frequency,Symbol Rate (use 0-9 keys), Polarity

and FEC (Use LEFT/RIGHT keys) in the appro-

priate boxes for the channels you wish to tune to.

Note: If you are using more than one LNB, be

sure to select the correct LNB (A, B,C or D)

for your tuning parameters.You can change

your LNB settings by highlighting the LNB

settings button and pressing OK (see page 22).

You need to press OK to update the entered

parameters and thereceiver will try to tune to

the new settings.

If the message “Signal Found” is displayed and

both the Signal and Data bar graphs are GREEN,

you may now select a tuning method.

If the message “No Signal” is shown, please

check that your tuning parameters are correct

and amend if necessary.

Check you LNB settings are correct (you can

access the LNB set-up menu by highlighting

the LNB Settings button and press OK; see

page 22 for LNB set-up information). If your Manual Tuning Menu

tuning and LNB settings are correct, your dish

may not be adequate to receive the signal or

out of alignment with the satellite.

Provided you are receiving a good Signal and Data, you may now proceed with one of the three

download methods: Network, Bouquet, or Manual. You may highlight the FTA box and change the

option to “on” to download Free-to-Air channels.

Use to change Satellite

LNB

Preset

Satellite

Frequence

Sym. Rate

Polarity

FEC

Auto Network Bouquet PIDs

FTA

Off

Signal

Data

F1 – Manual F2 - Mode

Use to change satellite

LNB

Preset

Satellite

Frequence

Sym. Rate

Polarity

FEC

Setup Satellite

Hotbird – 13.0E

11720

27500

Hor 18v

3/4

Auto Network Bouquet PIDs

FTA

Off

Signal

Data

F1 – Manual F2 - Mode

Setup Satellite

11720

27500

Hor 18v

3/4

Astra-19.2E

Signal Found

Tuning Modes:

Auto Tuning

From the select frequencies, the receiver will automatically search for all other frequencies within the

tuning range and downloads them automatically into the receiver. Once the channels have been

downloaded, all the TV and Radio channels will be displayed separately allowing the user to inspect

them and decide whether they are to be stored or aborted. This option is not available in Manual tuning

mode (F1).

Network and Bouquet Tuning

Within a digital broadcast transmission, many other network frequencies are provided to guide the

receiver to tune to other Networks. Network tuning enables the receiver to download other channels

from the same network. Use Bouquet tuning you only want to download channels from one channel

frequency group. Bouquet Tuning is used when only the channels from the desired frequency are to be

downloaded.

PID tuning

Apart from the usual channel parameters (Frequency,

Symbol Rate, Polarity and FEC value), the broadcaster

must include additional information (known as Packet

Identifiers or PIDs) in their transmission to allow auto-

tuning to work properly.

In “PID Tuning” you are required to enter the channel

name and three other parameters: Video PID, Audio

PID, PCR PID and Text PID (optional). These values

can either be in Decimal (ranging from 0 to 9) or Hexadecimal (ranging from 0 to 9 and A to F for each

digit).

After selecting from the Preset List, or Manually entering the basic channel parameters (Frequency,

Symbol Rate, Polarity and FEC value), move the cursor to highlight the Manual button and press OK to

start tuning.

Edit the Channel details by following the steps below:-

1. Use the UP, DOWN, LEFT/RIGHT keys, to move the cursor from one field to another.

2. Use the LEFT/RIGHT, F1 and F2 keys to enter the channel name.

3. Select the channel type whether it is a TV channel or a Radio channel.

4. Decide whether you would like to enter the PIDs in decimal or hexadecimal form.

5. Use the F1/ F2 and 0-9 keys to enter the PID values.

6. When you have finished and are ready to store and display that channel, press OK.

Note:

In order for manual tuning to be successful, the PCR PID must be entered. In many cases the PCR

PID is not published. Fortunately, in nearly all cases the PCR is the same as the Video PID or the

Audio PID or 8190 in decimal or 1FFE in hexadecimal.

The Teletext PID is optional and can be ignored when the value is unknown.

Name

Ch type

PIDs in

Hex/Dec

Hex

Audio

Video

Text

PCR

PID 0000

Hot Bird

13.0E

Setup Satellite:

If your desired satellite position is not on the Preset List, you can manually edit an existing satellite or

add a new satellite name to the preset list.

To add a new satellite to your list, you must first enter the channel tuning mode:

Press Menu, Channel Setup, OK:

From the Channel tuning menu press F1

to enter manual tuner mode.

You will now see a Setup Satellite button on

the right hand side.

Highlight the Setup Satellite button, press OK.

You will now see the Setup Satellite menu:

In the Setup Satellite menu you may either

press F1 to edit the highlighted satellite details,

or you may press F2 to add your own satellite

to the listing.

In either case you will then be required to enter

the new parameters in the boxes provided:

Satellite: Enter the satellite name

Position: Enter the satellite position in degrees,

then the decimal place and either E or W (East

or West).

Press OK when finished. Your new satellite will

be added to the Manual list on the screen.

Highlight the new satellite in the list and press

OK to return to the Channel tuning menu. You

will find your new satellite displayed in the

Satellite box.

Enter the transponder parameters and check

for signal availability.

Commence downloading your new channels.

Now any manual channels downloaded under

these parameters will be listed under the satellite

name you have entered.

Note:

In the Manual Tuning Menu, you can use the F2

key to toggle between the receiver”s preset satellite

list and the manually added satellite list.

Réseau Bouquet

FTA

Signal

Data

Satellite

Position .

TV Radio

Number of services

F1 –Edit’deeails F2 - Add

ABC

Astra 19.2 E

Sirius 1 / 2 50.E

Use to change satellite

LNB

Preset

Satellite

Frequence

Sym. Rate

Polarity

FEC

Setup Satellite

11720

27500

Hor 18v

3/4

Auto Network Bouquet PIDs

FTA

Off

Signal

Data

F1 – Manual 2 - Mode

123 5 E

Astra – 19.2E

Use to change satellite

LNB

Preset

Satellite

Frequence

Sym. Rate

Polarity

FEC

Auto Network Bouquet PIDs

FTA

Off

Signal

Data

F1 – Manual F2 - Mode

Setup Satellite

11720

27500

Hor 18v

3/4

Hotbird-13.0E

Editing channels:

Should you wish to modify or view details of a particular channel, you may do so by using the Edit

Channel Details menu.

Please note that apart from editing the channel name, editing any of the channel parameters will cause

the channel to either be lost or changed (different audio/video). This menu is best used for checking

channel parameters downloaded from the broadcaster.

To access the Edit Channel Details menu:

Press the MENU key, select Channel Setup,

then select Edit Channel Details and press OK.

By using the UP/DOWN, LEFT/RIGHT, F1/F2

and the OK/ESC keys, you may move to any

field to edit the associated parameters (the

operation is similar to using the manual tuning

menu). Once all changes have been made,

Press OK to retune to these new parameters.

Note: It is important to identify whether the channel is TV or Radio so that the channel is stored

under the appropriate channel list (TV or Radio List).

Arrange:

The channel sort facility allows you to “drag and drop” channels to your preferred location. Within the

“Channel Setup” menu, you will find the Sort Channels option:

Move the cursor to highlight “Arrange” in the Channel Setup menu and press OK.

Use the TV or Radio keys to select the

listing you wish to sort.

Use the UP/DOWN/LEFT/RIGHT keys

to move the cursor, highlight the channel

you wish to move and press OK to select

It.The selected channel now will move

with the cursor.

Use the UP/DOWN/LEFT/RIGHT keys

to move the channel to the new location.

Press OK to “drop” the selected channel

into the new position or ESC to cancel

the change.

Repeat for all other channels or press

ESC again to store the new settings and

Return to the previous menu.

Name

PIDs in

Hex/Dec

Audio PID

Video PID

Text PID

PCR PID

0000

Hex

LNB

Frequency 11278

Sym Rate 27500

Polarity Ver

FEC 7/8

Ch type

TV Channels

Radio

ESC

list radio

channels

select channel

exit

1 Sky 1

2 CNN

3 NBC

4 Movies 1

5 Sky News

6 Discovery

7 Kiosk 2

8 NRK 1

TV Channels

Radio

ESC

list radio

channels

select channel

exit

1 Sky 1

2 CNN

4 NBC

5 Movies 1

6 Skynews

7 Discovery

8 Kiosk 2

3 NRK 1

Page is loading ...

Samsung SADPCI-202 User manual

Brand: Samsung

Model: SADPCI-202

Category: Receiver

Type: User manual

Download PDF

report

Samsung SADPCI-202 User manual

Samsung SADPCI-202 User manual

Related papers

Other documents