ADLINK Technology cPCIS-3140/400 User manual

Brand: ADLINK Technology

Model: cPCIS-3140/400

Category: Power supply units

Type: User manual

This manual is also suitable for

NuIPC



cPCIS-3100 Series 6U 8-Slot CompactPCI

Sub-System and Components

User’s Guide

This user’s manual includes the information for the following products range:

Sub-systems:

Ÿ cPCIS-3120/300: 6U 8-slot CTI & Rear I/O CompactPCI Platform

with 300W Redundant PSU

Ÿ cPCIS-3120/400: 6U 8-slot CTI & Rear I/O CompactPCI Platform

with 400W Redundant PSU

Ÿ cPCIS-3120F/300: 6U 8-slot CompactPCI Platform with 300W

Redundant PSU

Ÿ cPCIS-3140/300: 6U 8-slot CTI & Rear I/O 64-bit CompactPCI

Platform with 300W Redundant PSU

Ÿ cPCIS-3140/400: 6U 8-slot CTI & Rear I/O 64-bit CompactPCI

Platform with 400W Redundant PSU

Components for 6U Sub-Systems

u Backplane options:

Ÿ cBP-6108 Series: 6U 32-bit CompactPCI backplanes

Ÿ cBP-6408 Series: 6U 64-bit CompactPCI backplanes

u Power supply options:

Ÿ APS-R300F: 300W Dual Redundant Front Access Power Supply

Ÿ APS-R400F: 400W Dual Redundant Front Access Power Supply

Manual Rev. 1.00: October 11, 2000

The information in this document is subject to change without prior notice in

order to improve reliability, design and function and does not represent a

commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special,

incidental, or consequential damages arising out of the use or inability to use

the product or documentation, even if advised of the possibility of such

damages.

This document contains proprietary information protected by copyright. All

rights are reserved. No part of this manual may be reproduced by any

mechanical, electronic, or other means in any form without prior written

permission of the manufacturer.

Trademarks

NuIPC is a registered trademark of ADLINK Technology Inc.

Other product names mentioned herein are used for identification purposes

only and may be trademarks and/or registered trademarks of their respective

companies.

Table of Contents • i

Table of Contents

How to Use This Manual...........................................3

Chapter 1 Introduction............................................1

1.1

System Features...................................................................1

1.2

Products Overview ...............................................................2

Chapter 2 6U CompactPCI Sub-systems.................4

2.1

Mechanical Drawing..............................................................4

2.2

General Features..................................................................5

2.3

General Chassis Specifications............................................7

2.4

Sub-systems Configurations................................................8

2.4.1 cPCIS-3120/300.................................................................................................8

2.4.2 cPCIS-3120/400.................................................................................................8

2.4.3 cPCIS-3120F/300...............................................................................................8

2.4.4 cPCIS-3140/300.................................................................................................8

2.4.5 cPCIS-3140/400.................................................................................................8

Chapter 3 Power Supply Unit..................................9

3.1

Features................................................................................9

3.2

Outlook ...............................................................................10

3.3

Specifications.....................................................................10

3.4

Pin Assignments of Connectors.........................................13

3.4.1

ATX Connector Pin Assignments.........................................................13

3.4.2

Peripheral Power Connectors................................................................13

3.4.3

Miscellaneous Connectors.....................................................................13

3.5

Installation..........................................................................15

3.5.1

AC Power Source Setting........................................................................15

3.5.2

Power Switch Installation........................................................................15

3.5.3

How to Replace the Power Module.......................................................15

Chapter 4 Backplane Options................................17

4.1

cBP-6108R..........................................................................17

4.1.1

PCB Drawing...............................................................................................17

4.1.2

Specifications.............................................................................................18

4.1.3

System Slot Pin assignments................................................................19

4.1.4

I/O Slot Pin assignments.........................................................................21

4.1.5

Utility I/O Slot (slot #9).............................................................................22

4.1.6

Special Power Connectors......................................................................22

4.1.7

Power Control & Status Signals ............................................................23

4.1.8

Signals for Power Indicator (J18)..........................................................23

4.1.9

ATX Power Input Connectors (J2, J3, J4)...........................................23

ii • Table of Contents

4.1.10

Mounting Holes..........................................................................................24

4.2

cBP-6108RE........................................................................24

4.3

cBP-6108F...........................................................................25

4.4

cBP-6408R..........................................................................26

4.4.1

PCB Drawing...............................................................................................26

4.4.2

Specifications.............................................................................................27

4.4.3

System Slot Pin assignments................................................................27

4.4.4

I/O Slot Pin assignments.........................................................................28

4.4.5

Special Power Connectors......................................................................29

4.4.6

Power Control Signals .............................................................................29

4.4.7

Power Indicator LED Signals J12..........................................................29

4.4.8

ATX Power Input Connectors (J2, J3, J4)...........................................29

4.4.9

Mounting Holes..........................................................................................30

Product Warranty/Service.......................................31

How to Use This Manual

This manual is designed to help you use the cPCIS-3100 Series 6U

CompactPCI Sub-system. It is divided into five chapters:

u Chapter 1, "Introduction," gives an overview of the product features.

u Chapter 2, "Sub-systems," describes the specifications, configuration

and installation of the sub-systems.

u Chapter 3, "Power Supply," describes the using of power supply.

u Chapter 4, "Backplane", describes the backplane specifications.

Introduction • 1

Introduction

This guide gives you the following information about the cPCIS-3100 series

6U CompactPCI sub-systems, including:

u System Features

u Product Overview

1.1 System Features

u System designed for 19-inch rack mounted or benchtop. Chassis is with

8U height.

u Mounting style can be front panel mounted or middle mounted.

u Drive bays and removable power supply are secured by door.

u Three 5 1/4 inches and one 3 1/2 inches drive bays.

u Force cooling system

Ÿ Three fans are used for cooling system and I/O boards. One fan is

push (taking-air-in) from the bottom and the other two fans are pull

(taking-air-out). The location of the push fan on the bottom side is

shift from center for cooling the CPU board (or system slot) in a most

effective way.

Ÿ Three fans are uses for cooling the redundant power supply and drive

bay. The two fans on the redundant PSU are push (taking-air-in). One

fan at the rear panel is pull (taking-air-out).

u Installed with front-accessed dual redundant AC power supply. The

maximum power can be 300W or 400W.

2 • Introduction

u Board Space:

Ÿ Front access or rear access are all possible.

Ÿ The space for backplane is 6U height, 10-slot width

Ÿ The 10 vertical slots width is suitable for installing a backplane with 7

I/O slots and one system slot. The system slot can install with a CPU

module up to 3 slots (12HP) wide

Ÿ With versatile backplane options.

u Cost effective version without rear I/O options are available upon

request.

1.2 Products Overview

The cPCIS-3100 series sub-systems are assembling by the cPCIS-3100

chassis and the following components:

Components:

u Power supply options:

Ÿ APS-R300F: 300W dual redundant power supply

Ÿ APS-R400F: 400W dual redundant power supply

u Backplane options:

Ÿ cBP-6108R: 6U 8-slot H.110 32-bit CompactPCI backplane with P3

Ÿ cBP-6108RE: 6U 8-slot H.110 32-bit CompactPCI backplane

Ÿ cBP-6108F: 6U 8-slot 32-bit front I/O backplane

Ÿ cBP-6408R: 6U 8-slot H.110 64-bit CompactPCI backplane

Sub-systems:

We provide a series of standard sub-systems based on the above

components options. Whenever the standard sub-systems cannot fully meet

your requirement, please contact with us for discussing the possibility for

more options. The following options are our standard sub-systems:

Ÿ cPCIS-3120/300: 6U 8-slot CTI & Rear I/O CompactPCI Platform with

300W Redundant PSU

Ÿ cPCIS-3120/400: 6U 8-slot CTI & Rear I/O CompactPCI Platform with

400W Redundant PSU

Ÿ cPCIS-3120F/300:6U 8-slot CompactPCI Platform with 300W

Redundant PSU

Ÿ cPCIS-3140/300: 6U 8-slot CTI & Rear I/O 64-bit CompactPCI

Platform with 300W Redundant PSU

Introduction • 3

Ÿ cPCIS-3140/400: 6U 8-slot CTI & Rear I/O 64-bit CompactPCI

Platform with 400W Redundant PSU

Note: To form a complete starting kit which user can install and run

applications, users need to order another CPU modules, I/O modules

and storage devices, which are not specified here.

4 • 6U CompactPCI Sub-systems

6U CompactPCI Sub-systems

In this chapter, we will describe the configurations and specifications of the

cPCIS-3100 series sub-systems.

2.1 Mechanical Drawing

6U CompactPCI Sub-systems • 5

2.2 General Features

Front Panel Features

u Stand 8U height, 19 inches rack-mountable design

u Space for seven I/O slots and one system module•

u Removable fan-tray (two pulling fans) ‚

u Security door

u Three 5 1/4 inches and one 3 1/2 inches drive bays, the following figure

shows a typical drive bay configuration ƒ

u Bay for dual redundant power supply„

u Power on/off switch…

u Reset switch†

u Pushing cooling fan on the bottom for best system slot cooling ‡

u Side handlesˆ

•

‚

‡

„

6 • 6U CompactPCI Sub-systems

Rear Panel Features

u Removable rear I/O card holders (top and bottom) •

u Exhaust Vent for the card cage ‚

u Exhaust Vent with cooling FAN for the drive bays and PSU ƒ

u Power core for PSU „

u Spared power core holder …

u The cost effective version without rear I/O feature is available upon

request.

Other Features

u Screw holes for side middle mounted

u Removable pushing fan on the bottom side

u Accessory kits for mounting the drives

u Card guides are installed, read card guides are used for system slot,

gray card guides are used for I/O slots.

u Well-designed for EMC

•

‚

„

6U CompactPCI Sub-systems • 7

2.3 General Chassis Specifications

u Dimension: 482.6 mm x 354.8 mm x 365 mm (WxHxD)

(Note: 482.6 mm = 19 inches, 354.8 mm = 8U height)

u Weight: 26 Kg (include redundant power supply, backplane)

u Front-access removable take-out fans on the top:

Ÿ Numbers of FAN: Two

Ÿ Fan type: DC brush-less motor

Ÿ Rated voltage: 12V

Ÿ Input Power: 9.84W (rated); 14.7W (maximum)

Ÿ Maximum Air flow: 37 CFM (when zero static pressure)

Ÿ Operating Temperature: -10 ~ 70 degree C

u Take-out fan on the rear panel:

Ÿ Fan type: DC brush-less motor

Ÿ Rated voltage: 12V

Ÿ Input Power: 5.4W (rated); 8.0W (maximum)

Ÿ Maximum Air flow: 90 CFM (when zero static pressure)

Ÿ Operating Temperature: -10 ~ 70 degree C

u Internal pushing fan on the bottom:

Ÿ Fan type: DC brush-less motor

Ÿ Rated voltage: 12V

Ÿ Input Power: 5.4W (rated); 8.0W (maximum)

Ÿ Maximum Air flow: 90 CFM (when zero static pressure)

Ÿ Operating Temperature: -10 ~ 70 degree C

u Dimension of the shipping box: 680 mm x 600 mm x 530 mm (WxHxD)

8 • 6U CompactPCI Sub-systems

2.4 Sub-systems Configurations

The following configurations are just brief descriptions. For more detail

descriptions of the backplane and power supply, please refer the next two

chapters.

2.4.1 cPCIS-3120/300

The cPCIS-3120/300 sub-system is with the following configuration:

u cPCIS-3100 chassis with rear I/O card options

u 300 Watts dual redundant power supply unit

u cBP-6108R: 6U 8-slot H.110 32-bit CompactPCI backplane

2.4.2 cPCIS-3120/400

The cPCIS-3120/400 sub-system is with the following configuration:

u cPCIS-3100 chassis with rear I/O card options

u 400 Watts dual redundant power supply unit

u cBP-6108R: 6U 8-slot H.110 32-bit CompactPCI backplane

2.4.3 cPCIS-3120F/300

The cPCIS-3120F/300 sub-system is the most cost effective option in the

cPCIS-3100 series sub-systems. It is with the following configuration:

u cPCIS-3100 chassis WITHOUT rear I/O card options

u 300 Watts dual redundant power supply unit

u cBP-6108F: 6U 8-slot 32-bit CompactPCI front I/O backplane

2.4.4 cPCIS-3140/300

The cPCIS-3140/300 sub-system is with the following configuration:

u cPCIS-3100 chassis with rear I/O card options

u 300 Watts dual redundant power supply unit

u cBP-6408R: 6U 8-slot H.110 64-bit CompactPCI backplane

2.4.5 cPCIS-3140/400

The cPCIS-3140/400 sub-system is with the following configuration:

u cPCIS-3100 chassis with rear I/O card options

u 400 Watts dual redundant power supply unit

u cBP-6408R: 6U 8-slot H.110 64-bit CompactPCI backplane

Power Supply Unit • 9

Power Supply Unit

The cPCIS-3100 series sub-systems are installed with 300W or 400W dual

redundant power supply by the front panel. In this chapter, the detail of the

power supply unit is described. The available models are list as following:

u APS-R300F: 300W dual redundant front-access power supply unit

u APS-R400F: 400W dual redundant front-access power supply unit

3.1 Features

u Redundant, hot-swappable dual power supply

u Easy to install and maintain

u Standard ATX interface with interface signal for power management

u Real-time disaster recovery with Zero-down-time

u Remote DC sense for compensating the cable drop

u Long-life ball bearing brush-less fans

u Secured key-lock to prevent unwanted removal of the PSU

10 • Power Supply Unit

3.2 Outlook

Note: This PSU modules are installed vertically inside the cPCIS-3100 sub-

systems.

3.3 Specifications

u AC Input Characteristics::

AC Input voltage is set manually by a 115/120 VAC switch.

Voltage Frequency

Minimum

Maximum

Input Current

115 VAC

47 ~ 63Hz

90 VAC

132 VAC

6.0A (300W)

9.0A (400W)

230 VAC

47 ~ 63Hz

180 VAC

264 VAC

3.5A (300W)

5.0A (400W)

u DC Output Characteristics:

Voltage +5V +3.3V

+12V

-5V -12V

5VSB

Max. Load 30A 15A 12A 0.5A

0.5A

Min. Load 3A

(1)

1A 0 0 0

300W

Max.Power Combined 150W

144W

2.5W

6W 4W

Voltage +5V +3.3V

+12V

-5V -12V

5VSB

Max. Load 50A 30A 15A 1.5A

1.5A

Min. Load 3A

(1)

1A 0 0 0

400W

Max.Power Combined total 370W

7.5W

18W

u Efficiency: 65% min at full load test

u Hold-up time:

20 milli-seconds at 115/230V AC full load after a loss of AC input

voltage

u Power good signal:

The power-good signal shall have a TURN-ON delay greater than

100 ms but less than 500 ms.

Power #1 LED Power #2 LED

Page is loading ...

ADLINK Technology cPCIS-3140/400 User manual

Brand: ADLINK Technology

Model: cPCIS-3140/400

Category: Power supply units

Type: User manual

This manual is also suitable for

Download PDF

report

ADLINK Technology cPCIS-3140/400 User manual

This manual is also suitable for

ADLINK Technology cPCIS-3140/400 User manual

Related papers

Other documents