Ferm TCM1002 Owner's manual

Brand: Ferm

Model: TCM1002

Type: Owner's manual

This manual is also suitable for

TCM1002 - TZ700

Page is loading ...

30 Ferm

TILE CUTTING MACHINE

TECHNICAL SPECIFICATIONS

PACKING CONTENTS

1 Tile cutting machine

1 Water reservoir

1 Instruction manual

1 Cutting guide

1 Mitre guide

FUNCTION

Various tiles and paving stones for walls and floors can be

cut using this machine. The maximum tile or stone

dimensions are 500 x 500 x 21 mm. The diamond blade

can be replaced by the customer. Use for cutting other

materials is prohibited.

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of the

instructions in this manual.

Denotes risk of electric shock.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

SAFETY PROVISIONS

• Before starting work, check your machine for

damage, with particular reference here to the dia-

mond blade. All parts must be fitted in the correct

manner and must comply with all preconditions to

guarantee optimal operation of the machine. For

continued use of the machine, the safety facilities or

slightly damaged parts should be tested for their cor-

rect operation. This must be carried out in accor-

dance with the aforementioned preconditions.

Moving parts, with particular reference to the pro-

tective cover for the diamond blade, should be secu-

rely fastened and may not stick or jam. Do not use

machines which do not have a switch for starting up

and shutting down.

• The protective cover for the diamond blade may not

be clamped in place or removed. A protective cover

that sticks or jams should be repaired immediately.

The riving knife may not be removed.

SETTING UP THE TILE CUTTING

MACHINE

• The tile cutting machine may only be used as a perma-

nent installation. Secure the machine by safely bolting

it to a level, horizontal surface. Use the screw holes

on the bottom of the machine to do this.

• Electrical connection should take place by means of a

230 V earthed wall socket (the mains voltage should

correspond with that stated on the type plate) which

is protected by a circuit breaker switch.

• The cable may not be used to pull the plug out of the

wall socket. Protect the cable from heat sources, oil

and sharp objects.

For your own safety, only use accessories and auxi-

liary equipment which are mentioned in the instruc-

tion manual or have been recommended or mentioned by the

manufacturer of the machine. Using other accessories or

auxiliary equipment can carry the risk of causing injury to you

or others.

Voltage | 230 V~

Frequency | 50 Hz

Power input | 400 W

No load speed | 2950/min

Max. cutting stroke 90º | 21 mm

Cutting angle | 0 - 45°

Measurements of bench | 390 x 340 mm

(sound pressure level) | 96 dB(A)

(sound power level) | 104.5 dB(A)

Vibration | < 2.5 m/s

English

Ferm 3

ìïéÑ, óàëíäÄ à êÖåéçí

• ëÎÂ‰ÛÂÚ ‚ÒÂ„‰‡ ‚˚ÌËÏ‡Ú¸ ‚ËÎÍÛ ÒÂÚÂ‚Ó„Ó ¯ÌÛ‡ ËÁ

ÓÁÂÚÍË ÔÓ ÓÍÓÌ˜‡ÌËË ‡·ÓÚ˚ Ë ÔÂÂ‰ ÚÂÏ, Í‡Í

˜ËÒÚËÚ¸ ÒÚ‡ÌÓÍ, ÏÂÌﬂÚ¸ ‰ËÒÍ ËÎË ÒÌËÏ‡Ú¸ ‚Ó‰ﬂÌÓÈ

·‡˜ÓÍ.

• ë‡ÁÛ ÔÓ ÓÍÓÌ˜‡ÌËË ‡·ÓÚ˚ Ì‡‰Ó ÔÓ˜ËÒÚËÚ¸

ÒÚ‡ÌÓÍ ÒÎÂ‰Û˛˘ËÏ Ó·‡ÁÓÏ:

‡) ‚˚ÌÛÚ¸ ‚ËÎÍÛ ÒÂÚÂ‚Ó„Ó ¯ÌÛ‡ ËÁ ÓÁÂÚÍË.

·) ÒÌﬂÚ¸ ·‡˜ÓÍ Ë ‰‡Ú¸ ÒÚÂ˜¸ „ﬂÁÌÓÈ ‚Ó‰Â.

‚) ÓÚ‚ËÌÚËÚ¸ Í˚¯ÍÛ-·˚Á„Ó‚ËÍ Ë ÔÓÏ˚Ú¸ Âﬁ.

„) ÓÚ‚ËÌÚËÚ¸ ÛÍÓﬂÚÍË-·‡‡¯ÍË, ÔÓ‰ÌﬂÚ¸

‡·Ó˜ËÈ ÒÚÓÎ Ë ÔÓÏ˚Ú¸ ‚ÂÒ¸ ÒÚ‡ÌÓÍ ËÁÌÛÚË.

• ëÚ‡ÌÓÍ ÓÚ‚Â˜‡ÂÚ ÒÓ‚ÂÏÂÌÌ˚Ï ÌÓÏ‡Ï ÚÂıÌËÍË

·ÂÁÓÔ‡ÒÌÓÒÚË. ã˛·˚Â ÂÏÓÌÚÌ˚Â ‡·ÓÚ˚

‰ÓÎÊÌ˚ ‚˚ÔÓÎÌﬂÚ¸Òﬂ ÚÓÎ¸ÍÓ

Í‚‡ÎËÙËˆËÓ‚‡ÌÌ˚Ï ÔÂÒÓÌ‡ÎÓÏ!

çÂÍ‚‡ÎËÙËˆËÓ‚‡ÌÌÓÂ ‚ÏÂ¯‡ÚÂÎ¸ÒÚ‚Ó ÔË‚Ó‰ËÚ

Í ËÒÍÛ Ú‡‚Ï‡ÚËÁÏ‡ Í‡Í ‰Îﬂ ÔÓÎ¸ÁÓ‚‡ÚÂÎﬂ-

ÓÔÂ‡ÚÓ‡, Ú‡Í Ë ‰Îﬂ ÓÍÛÊ‡˛˘Ëı. êÂ„ÛÎﬂÌÓ

ÔÓ‚ÂﬂÈÚÂ ÒÓÒÚÓﬂÌËÂ ÒÂÚÂ‚Ó„Ó ¯ÌÛ‡ Ë ÓÁÂÚÍË,

‡ Ú‡ÍÊÂ Û‰ÎËÌËÚÂÎﬂ, ÂÒÎË ÓÌ ÔËÏÂÌﬂÂÚÒﬂ. èË

ÔÓ‚ÂÊ‰ÂÌËË Î˛·Ó„Ó ËÁ ˝ÚËı ˝ÎÂÏÂÌÚÓ‚

Ó·‡˘‡ÈÚÂÒ¸ Á‡ ÔÓÏÓ˘¸˛ Í‚‡ÎËÙËˆËÓ‚‡ÌÌÓ„Ó

ÒÔÂˆË‡ÎËÒÚ‡. èÓ‚ÂÊ‰ÂÌÌ˚Â Á‡˘ËÚÌ˚Â

ÔËÒÔÓÒÓ·ÎÂÌËﬂ Ë ‚˚ÍÎ˛˜‡ÚÂÎË ‰ÓÎÊÌ˚Ï

Ó·‡ÁÓÏ Á‡ÏÂÌﬂ˛ÚÒﬂ ‰Îﬂ ÔÓÒÎÂ‰Û˛˘ÂÈ

ÌÓÏ‡Î¸ÌÓÈ ‡·ÓÚ˚ ÒÚ‡ÌÍ‡.

èêéÇÖêäÄ à áÄåÖçÄ êÖÜìôÖÉé

ÑàëäÄ

• êÂÊÛ˘ËÂ ‰ËÒÍË Ò ÚÂ˘ËÌ‡ÏË ËÎË ‰ÂÙÓÏ‡ˆËÂÈ

‰ÓÎÊÌ˚ Á‡ÏÂÌﬂÚ¸Òﬂ.

• íËÔ ‰ËÒÍ‡: ‡ÎÏ‡ÁÌ˚È ‰ËÒÍ ∆ 150 ÏÏ.

• ê‡ÁÂ¯‡ÂÚÒﬂ ËÒÔÓÎ¸ÁÓ‚‡Ú¸ ÚÓÎ¸ÍÓ ‰ËÒÍË,

ÛÍ‡Á‡ÌÌ˚Â ‚ ‰‡ÌÌÓÈ ËÌÒÚÛÍˆËË!

• ëÎÂ‰ÛÂÚ ‚ÒÂ„‰‡ ‚˚ÌËÏ‡Ú¸ ‚ËÎÍÛ ÒÂÚÂ‚Ó„Ó ¯ÌÛ‡ ËÁ

ÓÁÂÚÍË ÔÂÂ‰ ˜ËÒÚÍÓÈ ÒÚ‡ÌÍ‡, Á‡ÏÂÌÓÈ ‰ËÒÍ‡ ËÎË

Â„Ó Â„ÛÎËÓ‚ÍÓÈ.

• ëÎÂ‰ÛÂÚ ÔÓ‚ÂﬂÚ¸ Ì‡‰ÂÊÌÓÒÚ¸ ÙËÍÒ‡ˆËË ‰ËÒÍ‡

Ë Ô‡‚ËÎ¸ÌÓÒÚ¸ Ì‡Ô‡‚ÎÂÌËﬂ Â„Ó ‚‡˘ÂÌËﬂ.

• ëÌÓ¯ÂÌÌ˚È ‰ËÒÍ ÒÎÂ‰ÛÂÚ ÏÂÌﬂÚ¸ ‚ Ú‡ÍÓÈ

ÔÓÒÎÂ‰Ó‚‡ÚÂÎ¸ÌÓÒÚË (ËÒ.2):

‡) ‚˚ÌÛÚ¸ ‚ËÎÍÛ ÒÂÚÂ‚Ó„Ó ¯ÌÛ‡ ËÁ ÓÁÂÚÍË.

·) ÒÌﬂÚ¸ ‚Ó‰ﬂÌÓÈ ·‡˜ÓÍ (4) - ËÒ.1).

‚) ÓÚ‚ËÌÚËÚ¸ Ë ÒÌﬂÚ¸ ·ÓÎÚ˚ Í˚¯ÍË-·˚Á„Ó‚ËÍ‡.

„) ÓÚ‚ËÌÚËÚ¸ „‡ÈÍÛ (4), ÙËÍÒËÛ˛˘Û˛ ‰ËÒÍ (ËÒ.2)

‰) ÒÌﬂÚ¸ ‰ËÒÍ (2) (ËÒ.2) Ë Ì‡Ò‡‰ËÚ¸ ÌÓ‚˚È ‰ËÒÍ Ì‡

ÙÎ‡ÌÂˆ (1) - ËÒ.2. ç‡Ô‡‚ÎÂÌËÂ ‚‡˘ÂÌËﬂ

‰ÓÎÊÌÓ ÒÓ‚Ô‡‰‡Ú¸ ÒÓ ÒÚÂÎÍÓÈ Ì‡ ‰ËÒÍÂ. á‡ÚÂÏ

ÔÓÒÚ‡‚ËÚ¸ ÍÓÌÚÙÎ‡ÌÂˆ (3) - ËÒ.2).

Â) ÔË‚ËÌÚËÚ¸ ÙËÍÒËÛ˛˘Û˛ „‡ÈÍÛ (4) Ë

ÛÒÚ‡ÌÓ‚ËÚ¸ ·˚Á„Ó‚ËÍ Ì‡ ÏÂÒÚÓ.

Ê) Ó·ﬂÁ‡ÚÂÎ¸ÌÓ Û·Â‰ËÚ¸Òﬂ, ˜ÚÓ Ç˚ ÌÂ ÓÒÚ‡‚ËÎË

ÌËÍ‡ÍËı ËÌÒÚÛÏÂÌÚÓ‚ Á‡ ·˚Á„Ó‚ËÍÓÏ!

ìíàãàáÄñàü àçëíêìåÖçíÄ à

áÄôàíÄ éäêìÜÄûôÖâ ëêÖÑõ

ÖÒÎË Ç‡¯ ˝ÎÂÍÚÓËÌÒÚÛÏÂÌÚ ÔÓÒÎÛÊËÎ ‰ÓÒÚ‡ÚÓ˜ÌÓ

‰ÓÎ„ËÈ ÒÓÍ Ë ÌÂ ÔÓ‰ÎÂÊËÚ ‰‡Î¸ÌÂÈ¯ÂÈ

˝ÍÒÔÎÛ‡Ú‡ˆËË ËÎË Ç˚ ·ÓÎ¸¯Â ÌÂ ÒÓ·Ë‡ÂÚÂÒ¸

ËÒÔÓÎ¸ÁÓ‚‡Ú¸ Â„Ó, ÔÓÒËÏ Ç‡Ò ÔÓÁ‡·ÓÚËÚ¸Òﬂ Ó·

ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰Â Ë ÌÂ ‚˚·‡Ò˚‚‡Ú¸ Â„Ó ÍÛ‰‡

ÔÓÔ‡ÎÓ.

í‡ÍÓÂ Ó·ÓÛ‰Ó‚‡ÌËÂ ÛÚËÎËÁËÛÂÚÒﬂ ËÌ‡˜Â, ˜ÂÏ

Ó·˚˜Ì˚È ·˚ÚÓ‚ÓÈ ÏÛÒÓ. èÓ˝ÚÓÏÛ Ï˚ ÂÍÓÏÂÌ‰ÛÂÏ

Ç‡Ï Ó·‡ÚËÚ¸Òﬂ Í Ç‡¯ÂÏÛ ÏÂÒÚÌÓÏÛ ‰ËÎÂÛ Ferm ‰Îﬂ

ÛÚËÎËÁ‡ˆËË Ï‡¯ËÌ˚ ˝ÍÓÎÓ„Ë˜ÂÒÍË ÔËÂÏÎÂÏ˚Ï

ÒÔÓÒÓ·ÓÏ.

å˚ Á‡ﬂ‚ÎﬂÂÏ Ò Â‰ËÌÓÎË˜ÌÓÈ ÓÚ‚ÂÚÒÚ‚ÂÌÌÓÒÚ¸˛,

˜ÚÓ ‰‡ÌÌ‡ﬂ ÔÓ‰ÛÍˆËﬂ ÒÓÓÚ‚ÂÚÒÚ‚ÛÂÚ

ÌËÊÂÒÎÂ‰Û˛˘ËÏ ÌÓÏ‡Ï ËÎË

ÌÓÏ‡ÚË‚Ì˚Ï ‰ÓÍÛÏÂÌÚ‡Ï:

EN61029-1, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3

ÒÓ„Î‡ÒÌÓ ÔÓÎÓÊÂÌËﬂÏ ‰ËÂÍÚË‚:

98/37/EEC

73/23EEC

89/336/EEC

30-11-2002 „.

ÉÖçÖåéâÑÖç,

çË‰ÂÎ‡Ì‰˚

W. Kamphof

éÚ‰ÂÎ ÍÓÌÚÓÎﬂ Í‡˜ÂÒÚ‚‡

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ ВЕЛИКОБРИТАНИЯ

(

)

OPERATION

Fig.1

• Ensure that there is sufficient water in the water

reservoir (4) before starting work, i.e. enough to

allow the diamond blade to pass through the water.

During work activities, the water must be topped up

through the fill opening (6).

• Do not start work until the correct rotational speed

has been reached.

• Diamond blades may NEVER be exposed to sidelong

pressure! This can cause them to break. Flying pieces

act as missiles and are highly dangerous!

• Do not attempt to cut very small pieces of stone.

During work, always make sure that the entire sur-

face of the stone is resting on the work table. The

mitre guide (supplied) can be used to slide paving sto-

nes through the machine. Ensure that the paving

stone remains level, especially in the initial cutting

phase. Doing this prevents the blade from jolting

upwards during cutting.

• Do not overload your tools. Your work is carried out

better and safer within the given capacity range. Do

not cut other materials other than paving stones or

tiles.

• Meticulously maintain your tools. Keep your tools

sharp and clean in order to be able to work safely and

correctly. Follow the maintenance instructions and

the directions concerning replacement of the dia-

mond blade.

• Ensure that you stand in a safe position and always

keep your balance. Avoid unnatural bodily positions.

Be constantly on your guard. Use caution in everyt-

hing that you carry out. Be sensible at work. Do not

use the machine if you are not able to concentrate or

if you are tired.

CUTTING GUIDE

Fig.1

It is possible to cut parallel to another guiding edge using

the cutting guide (3).

Adjustment: undo the knobs (7) and adjust to the desired

distance. Retighten the knobs. The markings (8) indicate

the measurement.

MITRE ANGLE ADJUSTMENT

Fig.1

The mitre angle can be variably adjusted from 0° to 45°.

Undo the star-shaped knobs (5) and adjust the mitre

angle by tilting the table (1) upwards until the desired gra-

dient is reached. Finally, retighten the knobs (5).

CLEANING, MAINTENANCE AND

REPAIRS

• Remove the plug from the wall socket after use and

before cleaning the machine, replacing the diamond

blade or interchanging the water reservoir.

• The machine is cleaned immediately after use as fol-

lows:

a. Remove the plug from the wall socket.

b. Remove the water reservoir from the machi

ne and allow the dirty water to drain away.

c. Unscrew the water splashback cover and

clean this.

d. Undo the star-shaped knobs, fold the table

upwards and clean the entire machine.

• The machine complies with the current safety pre-

conditions. All repair work may only be performed

by a recognised company as unauthorised repair

attempts can carry the risk of injury to the user or to

bystanders. Regularly check the plug and cable and

allow these to be replaced by a recognised company

in the event of damage to either. Likewise, check the

extension cables. Damaged safety facilities and

switches should, in the correct manner, be replaced

in order to continue using the machine.

CHECKING AND REPLACING THE DIA-

MOND BLADE

• Diamond blades that are cracked or distorted should

be replaced.

• Type of blade: 150 mm diameter diamond blade.

• Diamond blades which do not comply with the speci-

fications laid down in this instruction manual may not

be used.

• The plug should be removed from the wall socket

before changing the blade and adjustment or cleaning

activities.

• Care should be taken to ensure that the diamond

blade is fitted securely and rotates in the correct

direction.

• To replace a worn blade you should proceed as fol-

lows (fig. 2):

a. Remove the plug from the wall socket.

b. Remove the water reservoir (4, fig. 1) from

the machine.

c. Undo and remove the attachment bolts for

the splashback cover.

d. Undo the nut which holds the blade in place

(4, fig. 2).

e. Remove the blade (2, fig. 2) and slide the

new blade onto the flange (1, fig. 2). Take care

to observe the direction of rotation which is

indicated by an arrow on the blade. Next, refit

the counterflange (3, fig. 2).

f. Retighten the nut which holds the blade in

place (4, fig. 2) and refit the water splashback

cover.

g. Be sure that you do not leave any tools

behind the water splashback cover.

4 Ferm

èË ˝ÍÒÔÎÛ‡Ú‡ˆËË ˝ÎÂÍÚË˜ÂÒÍËı Ï‡¯ËÌ ‚ÒÂ„‰‡

ÒÓ·Î˛‰‡ÈÚÂ ‰ÂÈÒÚ‚Û˛˘ËÂ Ô‡‚ËÎ‡ ÚÂıÌËÍË

·ÂÁÓÔ‡ÒÌÓÒÚË ‰Îﬂ ÒÌËÊÂÌËﬂ ËÒÍ‡ ÔÓÊ‡‡,

ÔÓ‡ÊÂÌËﬂ ˝ÎÂÍÚË˜ÂÒÍËÏ ÚÓÍÓÏ Ë Ú‡‚Ï.

èÓ˜ËÚ‡ÈÚÂ Ì‡ÒÚÓﬂ˘ËÂ ÚÂ·Ó‚‡ÌËﬂ, ‡ Ú‡ÍÊÂ

‚ıÓ‰ﬂ˘Û˛ ‚ ÍÓÏÔÎÂÍÚ ËÌÒÚÛÍˆË˛ ÔÓ ÚÂıÌËÍÂ

·ÂÁÓÔ‡ÒÌÓÒÚË.

ï‡ÌËÚÂ ËÌÒÚÛÍˆËË ‚ ÏÂÒÚÂ, Ó·ÂÒÔÂ˜Ë‚‡˛˘ÂÏ

Ëı ÒÓı‡ÌÌÓÒÚ¸!

èêÄÇàãÄ íÖïçàäà ÅÖáéèÄëçéëíà

• èÂÂ‰ Ì‡˜‡ÎÓÏ ‡·ÓÚ˚ ÌÛÊÌÓ Û·Â‰ËÚ¸Òﬂ ‚

ÓÚÒÛÚÒÚ‚ËË ÔÓ‚ÂÊ‰ÂÌËÈ Ì‡ ÒÚ‡ÌÍÂ, ÓÒÓ·ÂÌÌÓ Ì‡

ÂÊÛ˘ÂÏ ‰ËÒÍÂ. ÇÒÂ ˜‡ÒÚË ‰ÓÎÊÌ˚ ·˚Ú¸

Ô‡‚ËÎ¸ÌÓ ÛÒÚ‡ÌÓ‚ÎÂÌ˚ ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò

ÛÒÎÓ‚ËﬂÏË ‰Îﬂ Ó·ÂÒÔÂ˜ÂÌËﬂ ÓÔÚËÏ‡Î¸ÌÓÈ ‡·ÓÚ˚

ÒÚ‡ÌÍ‡. èË ÔÓ‰ÓÎÊËÚÂÎ¸ÌÓÏ ÂÊËÏÂ ‡·ÓÚ˚

ÒÎÂ‰ÛÂÚ ÔÓ‚ÂﬂÚ¸ ËÒÔ‡‚ÌÓÒÚ¸ Ë

‡·ÓÚÓÒÔÓÒÓ·ÌÓÒÚ¸ ËÁÌ‡¯Ë‚‡ÂÏ˚ı ËÎË ÒÎÂ„Í‡

ÔÓ‚ÂÊ‰ÂÌÌ˚ı ‰ÂÚ‡ÎÂÈ Ë Á‡˘ËÚÌ˚ı

ÔËÒÔÓÒÓ·ÎÂÌËÈ. ùÚÓ ‚˚ÔÓÎÌﬂÂÚÒﬂ ‚

ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò ‚˚¯ÂÛÔÓÏﬂÌÛÚ˚ÏË ÛÒÎÓ‚ËﬂÏË.

Ñ‚ËÊÛ˘ËÂÒﬂ ˜‡ÒÚË - ÓÒÓ·ÂÌÌÓ Á‡˘ËÚÌ˚È ÍÓÊÛı

‰ËÒÍ‡ - ‰ÓÎÊÌ˚ ·˚Ú¸ Ô‡‚ËÎ¸ÌÓ Á‡ÙËÍÒËÓ‚‡Ì˚ Ë

ÌÂ ‰ÓÎÊÌ˚ Á‡Â‰‡Ú¸. á‡ÔÂ˘‡ÂÚÒﬂ ËÒÔÓÎ¸ÁÓ‚‡Ú¸

ÒÚ‡ÌÓÍ ·ÂÁ ÍÌÓÔÓÍ ‚ÍÎ˛˜ÂÌËﬂ-ÓÚÍÎ˛˜ÂÌËﬂ.

• á‡ÔÂ˘‡ÂÚÒﬂ ÒÌËÏ‡Ú¸ Á‡˘ËÚÌ˚È ÍÓÊÛı ËÎË

‰ÓÔÓÎÌËÚÂÎ¸ÌÓ ÙËÍÒËÓ‚‡Ú¸ Â„Ó Í‡ÍËÏË-ÚÓ

ÔËÒÔÓÒÓ·ÎÂÌËﬂÏË. á‡ÍÎËÌË‚¯ËÈ ÍÓÊÛı ÒÎÂ‰ÛÂÚ

ÌÂÏÂ‰ÎÂÌÌÓ ÓÚÂÏÓÌÚËÓ‚‡Ú¸.

ìëíÄçéÇäÄ à çÄëíêéâäÄ

èãàíäéêÖáÄ

• ëÚ‡ÌÓÍ ÏÓÊÌÓ ËÒÔÓÎ¸ÁÓ‚‡Ú¸ ÚÓÎ¸ÍÓ Í

ÒÚ‡ˆËÓÌ‡ÌÓÏ ÂÊËÏÂ, Á‡ÙËÍÒËÓ‚‡‚ Â„Ó Í

Ó‚ÌÓÈ „ÓËÁÓÌÚ‡Î¸ÌÓÈ ÔÓ‚ÂıÌÓÒÚË ˜ÂÂÁ

ÓÚ‚ÂÒÚËﬂ ‚ ÌËÊÌÂÈ ˜‡ÒÚË ÒÚ‡ÌÍ‡.

• ç‡ÔﬂÊÂÌËÂ ÒÂÚË ˝ÎÂÍÚÓÔËÚ‡ÌËﬂ ‚ ÓÁÂÚÍÂ ‰Îﬂ

ÔÓ‰ÍÎ˛˜ÂÌËﬂ ÒÚ‡ÌÍ‡ ‰ÓÎÊÌÓ ·˚Ú¸ 230 Ç Ò

Á‡ÁÂÏÎÂÌËÂÏ Ë Á‡˘ËÚÓÈ ‡‚ÚÓÏ‡ÚË˜ÂÒÍËÏ

ÔÂ˚‚‡ÚÂÎÂÏ ˆÂÔË. ëÂÚÂ‚ÓÂ Ì‡ÔﬂÊÂÌËÂ

‰ÓÎÊÌÓ ÒÓÓÚ‚ÂÚÒÚ‚Ó‚‡Ú¸ ‚ÂÎË˜ËÌÂ, ÛÍ‡Á‡ÌÌÓÈ Ì‡

Á‡‚Ó‰ÒÍÓÈ Ú‡·ÎË˜ÍÂ.

• á‡ÔÂ˘‡ÂÚÒﬂ ÓÚÒÓÂ‰ËÌﬂÚ¸ ‚ËÎÍÛ ÓÚ Ì‡ÒÚÂÌÌÓÈ

ÒÂÚÂ‚ÓÈ ÓÁÂÚÍË ‚˚Úﬂ„Ë‚‡ÌËÂÏ Á‡ ÒÂÚÂ‚ÓÈ ¯ÌÛ.

òÌÛ ÒÎÂ‰ÛÂÚ Á‡˘Ë˘‡Ú¸ ÓÚ ‚ÓÁ‰ÂÈÒÚ‚Ëﬂ

ËÒÚÓ˜ÌËÍÓ‚ ÚÂÔÎ‡, ÓÚ Ï‡ÒÎ‡ Ë ÓÒÚ˚ı ÔÂ‰ÏÂÚÓ‚.

ÑÎﬂ ‚‡¯ÂÈ ÎË˜ÌÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË

‡ÁÂ¯‡ÂÚÒﬂ ÔËÏÂÌﬂÚ¸ ÚÓÎ¸ÍÓ ÚÂ

Á‡Ô˜‡ÒÚË Ë ÔËÒÔÓÒÓ·ÎÂÌËﬂ, ÍÓÚÓ˚Â ÔÂÂ˜ËÒÎÂÌ˚ ‚

‰‡ÌÌÓÈ ËÌÒÚÛÍˆËË ÎË·Ó ÂÍÓÏÂÌ‰Ó‚‡Ì˚

ÔÓËÁ‚Ó‰ËÚÂÎÂÏ Ï‡¯ËÌ˚. Ç ÔÓÚË‚ÌÓÏ ÒÎÛ˜‡Â Ç˚ Ò‡ÏË

ÔÓ‰‚Â„‡ÂÚÂÒ¸ Ë ÔÓ‰‚Â„‡ÂÚÂ ‰Û„Ëı ËÒÍÛ ÔÓÎÛ˜ÂÌËﬂ

Ú‡‚Ï˚.

êÄÅéíÄ çÄ ëíÄçäÖ

Fig.1

•èÂÂ‰ Ì‡˜‡ÎÓÏ ‡·ÓÚ˚ Ó·ÂÒÔÂ˜¸ÚÂ Ì‡ÎË˜ËÂ

‰ÓÒÚ‡ÚÓ˜ÌÓ„Ó ÍÓÎË˜ÂÒÚ‚‡ ‚Ó‰˚ ‚ ·‡˜ÍÂ (4) Ú‡Í,

˜ÚÓ·˚ ÌËÊÌﬂﬂ ˜‡ÒÚ¸ ÂÊÛ˘Â„Ó ‰ËÒÍ‡

ÔÓ„ÛÊ‡Î‡Ò¸ ‚ ÌÂÂ. èÓ‰ÎË‚ ‰ÂÎ‡ÂÚÒﬂ ˜ÂÂÁ

ÒÔÂˆË‡Î¸ÌÓÂ ÓÚ‚ÂÒÚËÂ (6) ÔË ‡·ÓÚÂ.

• çÂ Ì‡˜ËÌ‡ÈÚÂ ‡·ÓÚÛ, ÔÓÍ‡ ‰ËÒÍ ÌÂ ‰ÓÒÚË„ÌÂÚ

‰ÓÎÊÌÓÈ ÒÍÓÓÒÚË ‚‡˘ÂÌËﬂ.

• á‡ÔÂ˘‡ÂÚÒﬂ ÔËÍÎ‡‰˚‚‡Ú¸ Í ÂÊÛ˘ÂÏÛ ‰ËÒÍÛ

·ÓÍÓ‚ÓÂ ‰‡‚ÎÂÌËÂ, Ú‡Í Í‡Í ˝ÚÓ ÏÓÊÂÚ ÔË‚ÂÒÚË Í

ÔÓÎÓÏÍÂ ‰ËÒÍ‡ Ë Ì‡ÌÂÒÂÌË˛ Û‚Â˜ËÈ ÓÚÎÂÚÂ‚¯ËÏË

ÓÒÍÓÎÍ‡ÏË.

• çÂ ÒÎÂ‰ÛÂÚ ÂÁ‡Ú¸ Ó˜ÂÌ¸ Ï‡ÎÂÌ¸ÍËÂ ÔÂ‰ÏÂÚ˚.

èË ‡·ÓÚÂ ‚Òﬂ ÔÎÓÒÍÓÒÚ¸ ÔÎËÚÍË ‰ÓÎÊÌ‡

ÓÔË‡Ú¸Òﬂ Ì‡ ÔÓ‚ÂıÌÓÒÚ¸ ÒÚÓÎ‡ ÒÚ‡ÌÍ‡; ÔË ˝ÚÓÏ

Ì‡Ô‡‚Îﬂ˛˘‡ﬂ ÍÓÒÓ„Ó ÂÁ‡ ËÒÔÓÎ¸ÁÛÂÚÒﬂ ‰Îﬂ

ÔÓ‰‚ËÊÂÌËﬂ ÔÎËÚÍË ÔË ÂÁÍÂ. Ç Ì‡˜‡ÎÂ ÂÁÍË

Ì‡‰Ó ÔÎÓÚÌÓ ÔË‰‡‚ÎË‚‡Ú¸ ÔÎËÚÍÛ Í ÒÚÓÎÛ ‚Ó

ËÁ·ÂÊ‡ÌËÂ ÒÍ‡˜Í‡ ‰ËÒÍ‡.

• çÂ ÔÂÂ„ÛÊ‡ÈÚÂ Ò‚ÓÈ ÒÚ‡ÌÓÍ. ê‡·ÓÚ‡ ·Û‰ÂÚ

·ÓÎÂÂ ÔÓ‰ÛÍÚË‚ÌÓÈ Ë ·ÂÁÓÔ‡ÒÌÓÈ ‚ ÔÂ‰ÂÎ‡ı Â„Ó

ÏÓ˘ÌÓÒÚË. çÂ ËÒÔÓÎ¸ÁÛÈÚÂ ËÌ˚Â, ÌÂÊÂÎË

Ó„Ó‚ÓÂÌÌ˚Â ‡ÌÂÂ, Ï‡ÚÂË‡Î˚ ‰Îﬂ ÂÁÍË.

• í˘‡ÚÂÎ¸ÌÓ Ûı‡ÊË‚‡ÈÚÂ Á‡ Ò‚ÓËÏ ÒÚ‡ÌÍÓÏ,

‚Ó‚ÂÏﬂ Á‡Ú‡˜Ë‚‡ÈÚÂ ÂÊÛ˘ËÂ ˜‡ÒÚË, ÒÓ‰ÂÊËÚÂ

ËÌÒÚÛÏÂÌÚ ‚ ˜ËÒÚÓÚÂ ‰Îﬂ Â„Ó Ô‡‚ËÎ¸ÌÓÈ Ë

·ÂÁÓÔ‡ÒÌÓÈ ‡·ÓÚ˚. ëÓ·Î˛‰‡ÈÚÂ ÂÍÓÏÂÌ‰‡ˆËË

ÔÓ ÛıÓ‰Û Ë Á‡ÏÂÌÂ ÂÊÛ˘Â„Ó ‰ËÒÍ‡.

• Ç‡¯Â ÔÓÎÓÊÂÌËÂ Ë ÔÓÁ‡ ÔË ‡·ÓÚÂ ‰ÓÎÊÌ˚ ·˚Ú¸

·ÂÁÓÔ‡ÒÌ˚ÏË Ë ‚ÒÂ„‰‡ ÛÒÚÓÈ˜Ë‚˚ÏË Ë

ÂÒÚÂÒÚ‚ÂÌÌ˚ÏË. çÂ ÓÚ‚ÎÂÍ‡ÈÚÂÒ¸ ÔË ‡·ÓÚÂ,

ÔÓÒÚÓﬂÌÌÓ ·Û‰¸ÚÂ ‚ÌËÏ‡ÚÂÎ¸Ì˚Ï; ÒÓ·Î˛‰‡ÈÚÂ

ÓÒÚÓÓÊÌÓÒÚ¸. çÂ ÔËÒÚÛÔ‡ÈÚÂ Í ‡·ÓÚÂ, ÂÒÎË Ç˚

˜Û‚ÒÚ‚ÛÂÚÂ ÛÒÚ‡ÎÓÒÚ¸ Ë ÌÂ ÏÓÊÂÚÂ

ÒÍÓÌˆÂÌÚËÓ‚‡Ú¸Òﬂ.

èÄêÄããÖãúçÄü çÄèêÄÇãüûôÄü

Fig.1

ç‡ ÒÚ‡ÌÍÂ ÏÓÊÌÓ ÂÁ‡Ú¸ ÎËÌË˛ Ô‡‡ÎÎÂÎ¸ÌÓ Í‡ÍÓÈ-ÚÓ

ÍÓÏÍÂ (‰Û„ÓÈ ÎËÌËË) Ò ÔÓÏÓ˘¸˛ Ì‡Ô‡‚Îﬂ˛˘ÂÈ

(3). ÑÎﬂ ˝ÚÓ„Ó ÓÚ‚ÂÌËÚÂ ÛÍÓﬂÚÍË (7), ÛÒÚ‡ÌÓ‚ËÚÂ

ÌÛÊÌÓÂ ‡ÒÒÚÓﬂÌËÂ Ë Á‡ÚﬂÌËÚÂ Ëı. êËÒÍË Ì‡ ÎËÌÂÈÍÂ

(8) ÔÓÍ‡Á˚‚‡˛Ú ‚ÂÎË˜ËÌÛ ‡ÒÒÚÓﬂÌËﬂ.

êÖÉìãàêéÇäÄ ìÉãÄ éëà êÖáÄ

Fig.1

ì„ÓÎ ÓÒË ÂÁ‡ ÏÓÊÌÓ ÛÒÚ‡ÌÓ‚ËÚ¸ ÓÚ 0° ‰Ó 45°.

éÚÍÛÚËÚÂ ÛÍÓﬂÚÍË-·‡‡¯ÍË (5) Ë ÛÒÚ‡ÌÓ‚ËÚÂ

ÌÛÊÌ˚È Û„ÓÎ ÔÓ‰˙ÂÏÓÏ ÒÚÓÎ‡ (1) ‚‚Âı. ÇÌÓ‚¸

Á‡ÚﬂÌËÚÂ ÛÍÓﬂÚÍË (5).

Ferm 29

SCRAPPING OF ELECTRICAL TOOLS AND

CONSERVATION

If your electrical tool is at the stage where it has been

used intensively to such an extent that it must be

replaced, or if you no longer use it, please think about the

environment. Electrical equipment does not belong with

ordinary household waste but can be recycled in an envi-

ronmentally friendly manner. Ask your dealer for more

information about this.

We declare under our sole responsability that this

product is in conformity with the following

standards or standardized documents

EN61029-1, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3

in accordance with the regulations:

98/37/EEC

73/23EEC

89/336/EEC

from 30-11-2002

GENEMUIDEN NL

W. Kamphof

Quality department

FLIESENSCHNEIDMASCHINE

TECHNISCHE DATEN

VERPACKUNGSINHALT

1 Fliesenschneidmaschine

1 Wasserwanne

1 Bedienungsanleitung

1 Fliesenhalter

FUNKTION

Dieses Gerät dient dazu, verschiedene Fliesen für Wand

und Boden zu schneiden. Die max. Fliesenmaße betragen

500 x 500 x 21 mm. Die Trennscheibe kann vom Kunden

selbständig gewechselt werden. Das bearbeiten anderer

Werkstoffe ist nicht zulässig!

SICHERHEITSVORSCHRIFTEN

In dieser Betriebsanleitung erscheinen folgende Pikto-

gramme:

Verweist auf Verletzungs gefahr, Gefahr für Leben

und mögliche Beschädigung der Maschine, falls die

Anweisungen in dieser Betriebsanleitung nicht befolgt wer-

den.

Deutet das Vorhandensein elektrischer Spannung

an.

Lesen Sie diese Betriebsanleitung aufmerksam, bevor Sie

die Maschine in Betrieb nehmen. Machen Sie sich vertr-

aut mit der Funktionsweise und der Bedienung. Warten

Sie die Maschine entsprechend den Anweisungen, damit

sie immer einwandfrei funktioniert. Die Betriebsanlei-

tung und die dazugehörende Dokumentation müssen in

der Nähe der Maschine aufbewahrt werden.

Beachten beim Benutzen von Elek tromaschinen

immer die örtlichen Sicherheitsvorschriften bezüg-

lich Feuerrisiko, Elektroschock und Verletzung.

Lesen Sie außer den folgenden Hinweisen ebenfalls

die Sicherheitsvorschriften im einschlägigen Sonder-

teil.

Die Hinweise müssen sicher aufbewahrt werden!

Spannung | 230 V~

Frequenz | 50 Hz

Aufgenommene Leistung | 400 W

Drehzahl unbelastet | 2950/min

Max. Schnittleistung 90º | 21 mm

Schrägschnitte | 0-45°

Abbmessungen Tisch | 390 x 340 mm

(Schalldruckpegel) | 96 dB(A)

( Schallleistungspegel) | 104.5 dB(A)

Vibrationswert | < 2.5 m/s

Deutsch

DECLARATION OF CONFORMITY

(

)

Ferm 5

NEUPORABNO ELEKTRO ORODJE IN

ZAŠČITA OKOLJA

V primeru, da je vaše elektro orodje zaradi intenzivne

rabe potrebno zamenjati ali, da ni več uporabno, je pot-

rebno misliti na zaščito okolja. Elektro orodje ne sodi

med navadne hišne odpadke, zato ga je potrebno na

okolju prijazen način odstraniti. Vprašajte vašega stro-

kovnega trgovca (prodajalca) za nasvet.

Izjavljamo na lastno odgovornost da proizvod ustreza

zahtevam naslednjih standardov ali

normativnih dokumentov:

EN61029-1, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3

8/37/EEC

73/23EEC

89/336/EEC

od 30-11-2002

GENEMUIDEN NL

W. Kamphof

Quality department

èãàíäéêÖáçõâ ëíÄçéä

íÖïçàóÖëäàÖ ÑÄççõÖ

Ç äéåèãÖäí èéëíÄÇäà ÇïéÑàí

1 ëÚ‡ÌÓÍ

1 Å‡˜ÓÍ ‰Îﬂ ‚Ó‰˚

1 êÛÍÓ‚Ó‰ÒÚ‚Ó ÔÓ ˝ÍÒÔÎÛ‡Ú‡ˆËË

1 ç‡Ô‡‚Îﬂ˛˘‡ﬂ ÍÓÒÓ„Ó ÂÁ‡

çÄáçÄóÖçàÖ

ëÚ‡ÌÓÍ ÔÂ‰Ì‡ÁÌ‡˜ÂÌ ‰Îﬂ ÂÁÍË ‡ÁÎË˜Ì˚ı ÚËÔÓ‚

ÍÂ‡ÏË˜ÂÒÍÓÈ Ì‡ÔÓÎ¸ÌÓÈ Ë Ì‡ÒÚÂÌÌÓÈ ÔÎËÚÍË Ë

ÚÓÚÛ‡ÌÓÈ Í‡ÏÂÌÌÓÈ ÔÎËÚÍË Ï‡ÍÒËÏ‡Î¸ÌÓ„Ó

‡ÁÏÂ‡ ‰Ó 500ı500ı21 ÏÏ. ÄÎÏ‡ÁÌ˚È ‰ËÒÍ ÏÓÊÂÚ

Á‡ÏÂÌﬂÚ¸Òﬂ Ò‡ÏËÏ ÔÓÎ¸ÁÓ‚‡ÚÂÎÂÏ. êÂÁÍ‡ ‰Û„Ëı

Ï‡ÚÂË‡ÎÓ‚ Í‡ÚÂ„ÓË˜ÂÒÍË Á‡ÔÂ˘‡ÂÚÒﬂ!

íêÖÅéÇÄçàü èé íÖïçàäÖ

ÅÖáéèÄëçéëíà

Ç Ì‡ÒÚÓﬂ˘ÂÏ ÛÍÓ‚Ó‰ÒÚ‚Â ÔÓ ˝ÍÒÔÎÛ‡Ú‡ˆËË

ËÒÔÓÎ¸ÁÛ˛ÚÒﬂ ÒÎÂ‰Û˛˘ËÂ ÔÂ‰ÛÔÂ‰ËÚÂÎ¸Ì˚Â

ÒËÏ‚ÓÎ˚:

é·ÓÁÌ‡˜‡ÂÚ ËÒÍ Ú‡‚Ï˚, ÓÔ‡ÒÌÓÒÚ¸ ‰Îﬂ

ÊËÁÌË ËÎË ‚ÓÁÏÓÊÌÓÒÚ¸ ÔÓ‚ÂÊ‰ÂÌËﬂ

ËÌÒÚÛÏÂÌÚ‡ ‚ ÒÎÛ˜‡Â ÌÂÒÓ·Î˛‰ÂÌËﬂ ËÌÒÚÛÍˆËÈ

Ì‡ÒÚÓﬂ˘Â„Ó ÛÍÓ‚Ó‰ÒÚ‚‡.

é·ÓÁÌ‡˜‡ÂÚ ÓÔ‡ÒÌÓÒÚ¸ ÔÓ‡ÊÂÌËﬂ

˝ÎÂÍÚË˜ÂÒÍËÏ ÚÓÍÓÏ.

ÇÌËÏ‡ÚÂÎ¸ÌÓ ÔÓ˜ËÚ‡ÈÚÂ Ì‡ÒÚÓﬂ˘ÂÂ ÛÍÓ‚Ó‰ÒÚ‚Ó

ÔÂÂ‰ ˝ÍÒÔÎÛ‡Ú‡ˆËÂÈ Ï‡¯ËÌ˚.

àÁÛ˜ËÚÂ ÛÒÚÓÈÒÚ‚Ó, ÔËÌˆËÔ ‡·ÓÚ˚ Ë ÔÓﬂ‰ÓÍ

˝ÍÒÔÎÛ‡Ú‡ˆËË Ï‡¯ËÌ˚. ÑÎﬂ Ó·ÂÒÔÂ˜ÂÌËﬂ

Ì‡‰ÎÂÊ‡˘ÂÈ ‡·ÓÚ˚ ‚˚ÔÓÎÌﬂÈÚÂ ÚÂıÌË˜ÂÒÍÓÂ

Ó·ÒÎÛÊË‚‡ÌËÂ ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò ËÌÒÚÛÍˆËﬂÏË.

ëÓı‡ÌﬂÈÚÂ Ì‡ÒÚÓﬂ˘ÂÂ ÛÍÓ‚Ó‰ÒÚ‚Ó Ë ‚ıÓ‰ﬂ˘Û˛ ‚

ÍÓÏÔÎÂÍÚ ‰ÓÍÛÏÂÌÚ‡ˆË˛.

ç‡ÔﬂÊÂÌËÂ ÒÂÚË | 230 Ç~

ó‡ÒÚÓÚ‡ ÚÓÍ‡ | 50 Éˆ

èÓÚÂ·ÎﬂÂÏ‡ﬂ ÏÓ˘ÌÓÒÚ¸ | 400 ÇÚ

ëÍÓÓÒÚ¸ ·ÂÁ Ì‡„ÛÁÍË | 2950/ÏËÌ

å‡ÍÒ. ¯‡„ ıÓ‰‡ ÔËÎÍË 90° | 21 ÏÏ

ì„ÓÎ ÂÁ‡ | 0 - 45°

ê‡ÁÏ˚ ÒÚÓÎ‡ ÒÚ‡ÌÍ‡ | 390 x 340 ÏÏ

Lpa Ñ‡‚ÎÂÌËÂ Á‚ÛÍ‡ | 96 ‰Å(A)

Lwa åÓ˘ÌÓÒÚ¸ Á‚ÛÍ‡ | 104.5 ‰Å(A)

ÇÂÎË˜ËÌ‡ ‚Ë·‡ˆËË | <2.5 Ï/ÒÂÍ

Russian

IZJAVA O SKLADNOSTI

(

)

28 Ferm

Page is loading ...

Ferm TCM1002 Owner's manual

Brand: Ferm

Model: TCM1002

Type: Owner's manual

This manual is also suitable for

TCM1002 - TZ700

Download PDF

report

in other languages

français: Ferm TCM1002 Le manuel du propriétaire
Deutsch: Ferm TCM1002 Bedienungsanleitung
Nederlands: Ferm TCM1002 de handleiding
dansk: Ferm TCM1002 Brugervejledning
čeština: Ferm TCM1002 Návod k obsluze
svenska: Ferm TCM1002 Bruksanvisning
suomi: Ferm TCM1002 Omistajan opas

Ferm TCM1002 Owner's manual

This manual is also suitable for

Ferm TCM1002 Owner's manual

in other languages

Related papers

Other documents