Beta 1498MN/12 Operating instructions

1498MN/12

MODE D’EMPLOI

GEBRAUCHSANWEISUNG

INSTRUCCIONES

GEBRUIKSAANWIJZING

INSTRUKCJA OBSŁUGI

ISTRUZIONI PER L’USO

INSTRUCTIONS FOR USE

INSTRUÇÕES DE USO

HASZNÁLATI ÚTMUTATÓ

I

D

NL

EN

E

PL

F

PT

HU

1498MN_12.indd 1 11/07/16 15:14

Page is loading ...

3

FUSE

Anti Recharge Diode

Connector

Clamps + / -

Samsung

etc.

Samsung

etc.

NO

RISK OF DAMAGE

OK

DUAL CHARGE

1498MN_12.indd 3 11/07/16 15:14

Page is loading ...

8

CAUTION: Recharge the emergency booster for at least 5 hours immediately after purchase, and after each use. If not in use,

recharge the emergency booster at least once a month for 5 hours, to keep the internal battery perfectly efcient. Never leave

the emergency booster at for prolonged periods of time; the efciency of the internal battery might be signicantly

reduced, thus affecting the operation of the device.

WARNINGS

Operating precautions:

CAUTION: Read the WARNINGS carefully before using the product. The improper use of the product will void the warranty!

• Use the emergency booster with care.

• This device must not be used by anyone not in good health or children without supervision.

• Keep out of the reach of children. This device is not a toy.

• Always wear protective goggles and keep your face away from the battery when connecting and disconnecting it.

•The battery contains corrosive liquid; in the event of accidental contact with the skin or the eyes, rinse immediately

with water and seek medical advice.

• Explosive gases could be given off while starting the battery; therefore, avoid sparks and ames and do not smoke

near the engine and the battery.

• Do not use the emergency booster near heat sources or ammable material.

• Do not drop metal tools on the battery. This could cause a short-circuit.

• Do not wear metal objects (rings, bracelets, watches etc.) when working with a battery.

IMPORTANT SAFETY MEASURES

• Do not put any objects into any slots or openings on the surface of the emergency booster.

• To recharge the emergency booster, only use the wall charger supplied with the emergency booster, or the 12V

DC car charger. Charge in well-ventilated and dry rooms: do not expose the emergency booster to rain or snow.

• To disconnect the wall charger or the car charger from the emergency booster or the wall socket, pull the plug; do

not pull the cable.

• Do not recharge the emergency booster if the wall charger or the car charger are damaged; please contact your

dealer to replace or repair the device. Replace only with original spare parts supplied by the manufacturer.

• Do not use the emergency booster if the plastic is broken, or if it gives off unusual smells or too much heat.

• The device must be repaired or serviced by trained personnel only.

• The emergency booster is designed to start lead acid batteries. Do not use it for any other purposes.

Do not start or charge disposable batteries. Do not start or charge frozen batteries.

• Do not start or charge batteries with any voltages other than those stated in the technical data of the booster.

CAUTION: IF THE VOLTAGE OF THE EMERGENCY BOOSTER DOES NOT MATCH THE VOLTAGE OF THE VEHICLE’S

SYSTEM, AN EXPLOSION, OR DAMAGE TO THE VEHICLE, THE PRODUCT AND PEOPLE COULD OCCUR.

INSTRUCTIONS FOR USE

EN

1498MN_12.indd 8 11/07/16 15:14

9

• Before starting the vehicle, turn off the lights and any running accessories.

• CAUTION: Never allow the clips of the two clamps (positive-red and negative-red) to touch together.

• CAUTION: Never reverse polarity. Always connect the output lead with red clamp (+) to the positive post of the

battery, and the output lead with black clamp (-) to the vehicle’s chassis.

• CAUTION: REVERSED POLARITY CAN CAUSE AN EXPLOSION OR DAMAGE TO THE VEHICLE, THE PRO

DUCT AND PEOPLE.

• Improper use of the emergency booster or tampering with the built-in electronic circuit will invalidate your warranty.

HOW TO RECHARGE THE EMERGENCY BOOSTER

The emergency booster can be charged either through the wall charger supplied with it or the 12V car charger.

CAUTION: Recharge the emergency booster for at least 5 hours immediately after purchase, and after each use. If not in

use, recharge the emergency booster at least once a month, to keep the internal battery perfectly efcient.

Charging the emergency booster using the WALL CHARGER

1. Make sure that no device is connected to the emergency booster (see section Using the emergency booster as a power

source). Move the ON/OFF switch to the ON position and press button to check the battery charging status (0% to 100%).

2. Plug the 230V charger into the emergency booster socket.

3. Plug the charger into the 230V mains socket. The display will turn on, and the battery charge percentage will

show up. Charge is complete when the 100% indicator appears on the display.

4. Now the battery charger can be disconnected from the booster.

5. If not in use, recharge the emergency booster at least once a month for 5 hours, to keep the internal battery

perfectly efcient. The battery charger of the emergency booster is automatic.

CAUTION: Only use the charger that was included with the booster.

CAUTION: If the battery is not fully charged after 5 hours, the battery charger will automatically stop charging. If this should

occur, have the booster checked by a trained service centre.

Charging the emergency booster using the CAR CHARGER

1. Make sure that no device is conn ected to the emergency booster (see section Using the emergency booster as a power

source). Move the ON/OFF switch to the ON position and press button to check the battery charging status

(0% to 100%).

2. Plug either end of the CAR CHARGER into the emergency booster socket.

3. Start the vehicle; then plug the other end of the car charger into the 12V DC cigarette lighter socket of the vehicle.

The display will turn on, and the battery charge percentage will show up. The message “IN 15V 1A” indicates that

the recharging plug has been correctly plugged into the booster, and that the battery is charging. When the battery

is fully charged, both the message “IN 15V 1A” and the display will turn off.

4. Now the battery charger can be disconnected from the booster.

CAUTION: Always disconnect the emergency booster from the cigarette lighter socket if the vehicle’s engine is not running.

INSTRUCTIONS FOR USE

EN

1498MN_12.indd 9 11/07/16 15:14

10

HOW TO USE THE EMERGENCY BOOSTER

Using the emergency booster to start vehicles

1. Always wear protective goggles and keep your face away from the battery during connection operations.

2. Check that the installed battery is a 12V.

CAUTION: IF THE VOLTAGE OF THE EMERGENCY BOOSTER DOES NOT MATCH THE VOLTAGE OF THE VEHI-

CLE’S SYSTEM, AN EXPLOSION, OR DAMAGE TO THE VEHICLE, THE PRODUCT AND PEOPLE COULD OCCUR.

3. Connect the starter cable supplied with the booster and check that both LEDs (red and green) on the connector are

ashing.

CAUTION: DO NOT CONNECT THE EMERGENCY BOOSTER TO THE BATTERY IF THE GREEN LED IS GLOWING

SOLID, BECAUSE PROTECTION IS DISABLED IN THIS MODE.

4. Determine which post of the battery is grounded to the chassis; in most vehicles, the negative post is grounded to the

chassis.

CAUTION: Never reverse polarity. Always connect the output lead with red clamp (+) to the positive post of the battery,

and the output lead with black clamp (-) to the vehicle’s chassis.

CAUTION: REVERSED POLARITY CAN CAUSE AN EXPLOSION OR DAMAGE TO THE VEHICLE, THE PRODUCT

AND PEOPLE.

CAUTION: Check that the cables of the emergency booster are kept away from fans, moving parts and the fuel pipe.

6. Check that the green LED on the booster cable is on.

CAUTION: When the green LED goes on, the vehicle should be started within 30 seconds. After 30 seconds, the ignition

cable must be restored by disconnecting and connecting again either clamp.

7. Crank the engine.

8. After the engine starts, disconnect the output lead with black clamp from the vehicle’s chassis.

9. Disconnect the output lead with red clamp from the positive clip (+) of the battery.

CAUTION: IF THE ENGINE DOES NOT START, DISCONNECT EITHER CLAMP TO RESTORE THE STARTER CABLE.

CAUTION: Charge the emergency booster after each use.

IMPORTANT! Maintaining your vehicle’s battery properly will prolong its life; when you reach your destination, please

remember to plug a vehicle battery charger into your battery, to fully restore its efciency.

Troubleshooting

Problem Cause Solution

When starter cable is connected, a continuous

sound is heard.

Internal battery is at. Disconnect cable and charge emergency

booster.

After starter cable has been connected to car

battery, it is not activated (LEDs blink).

Car battery voltage is too low (<1.5V). Use different start systems.

After starter cable has been connected to car

battery, red LED glows solid and an intermittent

sound is heard.

Battery cables have been reversed. Disconnect cables from battery and connect

them again correctly.

After starter cable has been connected to car

battery, red LED glows solid and a continuous

sound is heard.

A short-circuit has occurred. Disconnect cables from battery and check

vehicle to clear short-circuit.

LCD display shows the word “EA”. Voltage of a cell of emergency booster battery

is too low.

Try to charge booster for at least two hours,

disconnect power supply, and then start a

normal charging cycle. If the word “EA” does not

disappear, please contact service centre.

INSTRUCTIONS FOR USE

EN

1498MN_12.indd 10 11/07/16 15:14

11

USING THE LED LAMP

Move the ON/OFF switch to the ON position and press button

STEADY LIGHT: press button for 3 seconds.

FLASHING LIGHT: press button for 1 second.

SOS EMERGENCY LIGHT: press button for 1 second.

To turn the LED lamp off, press button for 1 second, and move the ON/OFF switch to the OFF position.

USING THE BOOSTER AS A BATTERY CHARGER FOR ELECTRONIC DEVICES

The device can charge different types of mobile phones, smartphones, tablets, MP3/MP4 players, navigators and other

devices tted with 5V 1A/2,1A USB plugs.

CHARGING PROCEDURE

1. Make sure that the device to charge is equipped with a 5V USB plug.

2. Plug the USB charging cable into the booster.

3. Plug the other end of the cable into the device to charge.

4. Move the ON/OFF switch to the ON position and press button The display will turn on, indicating that your device is

charging. The display shows the type of USB port that is being used and the remaining charge percentage of the booster’s

internal battery.

The device is equipped with two USB outlets, which makes it possible to charge two devices simultaneously, provided that

two cables are used for each device.

CAUTION Never charge two devices using the same cable; irreparable damage could occur.

CAUTION Always recharge the emergency booster if it is used extensively in this mode.

The USB outlets are protected against overloads. In case of overload, the USB outlets of the booster will be automatically

switched off. To switch them on, just remove the excess load and press button

The internal battery of the booster is protected against overdischarges. In case of overdischarge, the USB outlets of the

booster will be automatically switched off. If this should occur, unplug the devices to charge and charge the booster, to fully

restore the efciency of its battery.

WARRANTY CONDITIONS

1.This product is warranted by the manufacturer for a period of 24 months (except for the battery, which is warranted

for 12 months) from date of purchase, as stated on the proof of purchase from the dealer.

2.The warranty provides for free repair or replacement of any parts in case of manufacturing and material defects

acknowledged by the manufacturer.

3. Any problems arising from negligence, misuse or tampering with the device will void the warranty.

4.The internal battery of the emergency booster should be charged regularly (according to this manual), only using

the charger supplied with it. Improper maintenance of the battery will void the warranty.

5.The warranty will only be valid if the device is repaired by trained personnel authorised by the manufacturer.

6.Incorrect connection to the mains, differences between the power supply voltage and the plate rated voltage of

the device, and line voltage uctuations caused, for example, by external agents and lightning strikes, will invali

date the warranty.

7.Any returned devices must be shipped CARRIAGE FREE and will be sent back CARRIAGE FORWARD.

8 The warranty certicate must be accompanied by either a valid purchase receipt or a bill of parcel.

9. No liability can be accepted for direct or consequential damages to persons or things of any kind whatsoever

arising in connection with the use or interruption of use of the device.

INSTRUCTIONS FOR USE

EN

1498MN_12.indd 11 11/07/16 15:14

Page is loading ...

42

Informazione agli utenti

Il simbolo del cassonetto barrato riportato sull’ apparecchiatura o sulla confezione indica che il prodotto, alla fine

della sua vita utile, deve essere smaltito separatamente dagli altri rifiuti urbani.

L’utilizzatore che intendesse smaltire questo strumento può:

– consegnarlo presso un centro di raccolta di rifiuti elettronici od elettrotecnici

– riconsegnarlo al proprio rivenditore al momento dell’acquisto di uno strumento equivalente.

– nel caso di prodotti ad uso esclusivo professionale, contattare il produttore che dovrà disporre una procedura per

il corretto smaltimento.

Il corretto smaltimento di questo prodotto permette il riutilizzo delle materie prime in esso contenute ed evita danni

all’ambiente ed alla salute umana.

Lo smaltimento abusivo del prodotto costituisce una violazione della norma sullo smaltimento di rifiuti pericolosi,

comporta l’applicazione delle sanzioni previste.

User Information

The crossed-out wheeled bin symbol on either the equipment or the packaging means that the product must be dispo-

sed of separately from other urban waste at the end of its service life.

Any user who plans to dispose of this instrument may:

– deposit it at an electronic or electrotechnical waste collection point

– return it to the dealer upon purchase of an equivalent instrument

– in case of products for professional use only, contact the manufacturer, who will have to arrange for proper disposal.

Properly disposing of this product allows the raw materials used in it to be reused and prevents damage to the

environment and human health.

Unauthorized disposal of the product constitutes a breach of the provision concerning hazardous waste disposal and

involves enforcing the sanctions provided for by law.

Information pour les utilisateurs

Le symbole de la poubelle barrée présent sur l’équipement ou son emballage indique que le produit doit, lorsqu’il a

atteint la fin de sa vie utile, être éliminé séparément des déchets urbains classiques.

L’utilisateur qui décide de procéder à l’élimination de cet appareil peut:

– le déposer dans un centre de collecte des déchets électroniques ou électrotechniques;

– le remettre à son revendeur au moment de l’achat d’un appareil équivalent;

– dans le cas de produits à usage professionnel, contacter le constructeur qui devra entreprendre une procédure

d’élimination ad hoc.

L’élimination correcte de ce produit permet de réutiliser les matières premières qu’il contient et évite de porter préjudi-

ce à l’environnement et à la santé de l’homme.

Toute élimination abusive de ce produit est une violation de la norme en matière d’élimination des déchets dangereux

et entraine l’application des sanctions prévues.

Informationen für Benutzer

Der durchgestrichene Abfallcontainer auf dem Gerät oder auf der Packung bedeutet, dass das Produkt am Ende

seiner Lebensdauer getrennt von anderem Müll entsorgt werden muss.

Der Benutzer kann dieses Gerät wie folgt entsorgen:

– es an eine Sammelstelle für elektronische und elektrotechnische Abfälle bringen;

– das alte Gerät beim Kauf eines neuen gleichwertigen Geräts dem Händler übergeben;

– bei ausschließlich für berufliche Zwecke vorgesehenen Produkten, den Hersteller für die Anordnung eines Verfah-

rens für die korrekte Entsorgung einschalten.

Die korrekte Entsorgung dieses Produkts ermöglicht die Wiederverwertung der in ihm enthaltenen Rohstoffe und

vermeidet Umwelt- und Gesundheitsschäden.

Die unbefugte Entsorgung des Produkts stellt eine Verletzung der Vorschrift für die Entsorgung von gefährlichen

Abfällen dar und hat die Anwendung der vorgesehenen Strafen zur Folge.

Información a los usuarios

El símbolo del contenedor de residuos con la cruz que viene en el envase o en el equipo significa que el producto, al

final de su vida útil, ha de eliminarse separado de otros residuos urbanos.

El usuario que tiene la intención de eliminar este instrumento puede:

– llevarlo a un centro de recogida de residuos electrónicos o electrotécnicos

– llevarlo a su revendedor cuando compra un equipo equivalente

– en caso de productos de uso profesional exclusivo, contacte con el fabricante que tendrá que adoptar un procedi-

miento para la eliminación correcta.

La eliminación correcta de este producto permite volver a utilizar las materias primas que el mismo contiene y evita

daños al medio ambiente y a la salud humana.

La eliminación abusiva del producto supone una violación de la normativa sobre la eliminación de residuos peligrosos,

asícomo la aplicación de las sanciones previstas.

Informação aos utentes

O símbolo do caixote de lixo barrado contido no aparelho ou na embalagem indica que o produto, no fim da sua

vida útil, deve ser eliminado separadamente dos outros lixos urbanos.

O utilizador que pretende eliminar este instrumento pode:

- entregá-lo junto a um ponto de colecta de lixos electrónicos ou electrotécnicos

- devolvê-lo ao próprio revendedor no momento da compra de outro instrumento equivalente

- no caso de produtos de uso exclusivamente profissional, contactar o produtor que deverá dispor um procedimento

para a eliminação correcta.

A eliminação correcta deste produto possibilita a reutilização das matérias-primas contidas no mesmo e evita

danos ao ambiente e à saúde humana.

A eliminação do produto de maneira irregular constitui uma violação da norma sobre a eliminação de lixos perigo-

sos e comporta a aplicação das sanções previstas.

I

EN

F

D

E

PT

1498MN_12.indd 42 11/07/16 15:14

Page is loading ...

44

BETA UTENSILI S.p.A.

via Alessandro Volta, 18 - 20845 Sovico (MB) ITALY

Tel. +39 039.2077.1 - Fax +39 039.2010742

www.beta-tools.com

1498MN_12.indd 44 11/07/16 15:14

Beta 1498MN/12 Operating instructions

Beta 1498MN/12 Operating instructions

in other languages

Related papers

Other documents