Mettler Toledo O2 transmitter O2 4050e Operating instructions

O

2

Transmitter 4050 e

Instruction manual

O

2

Transmitter 4050 e

52 121 142

Cal

R

el

Enter

R

el

M

ode

R

el

Cal

Enter

Rel

Mode

Rel

ESC

O

2

4

05

0

e

O

2

4050 e

Preface

This manual serves to explain the use of the O

2

Transmitter 4050 e Series. The manual functions in two

ways, firstly as a step by step guide to help the user operate the instrument, and secondly as a handy refe-

rence guide. This instruction manual is written to cover as many anticipated applications of the O

2

Trans-

mitter 4050 e as possible. If you have any doubts concerning the use of the instrument, please do not hesi-

tate to contact the nearest METTLER TOLEDO Authorized Distributor.

The information presented in this manual is subject to change without notice as improvements are made,

and does not represent any commitment whatsoever on the part of METTLER TOLEDO.

METTLER TOLEDO cannot accept any responsibility for damage or malfunction of the unit due to improper

use of the instrument.

O

2

Transmitter 4050 e 3

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

Contents

1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 At the very beginning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Safety intsructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Description of unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Measurement and control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Unit overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Assembly and installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1 Mounting the unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.2 Connection diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 Normal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5 Calibration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.1 Entering Calibration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.3 View actual zero and slope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6 Setup mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.1 Enter Setup mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.2 Electrode Offset (OFS) sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6.3 Setting temperature (Set °C°F) sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.4 Control Relay A / Relay B (SP1/SP2) sub-function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.5 Controller (CNTR) sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.6 Current Output 1 sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.7 Current Output 2 sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.8 Wash relay (WASH) sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.9 Configuration (CNFG) sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.10 Calibration (CAL) sub-function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7 Relay Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.1 View relay set points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.2 Manual relay mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

8Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

8.1 General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

8.2 Specifications for wall mount version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8.3 Specifications for panel mount version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

9 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9.1 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9.2 Packaging / Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9.3 Return of goods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9.4 Guidelines for returning unit for repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

10 Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

10.1 Appendix 1 – Unit fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

10.2 Appendix 2 – Dissolved oxygen values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

10.3 Appendix 3 – Simple explanation on the function of hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

10.4 Appendix 4 – General instructions concerning controller setting. . . . . . . . . . . . . . . . . . . . . . . . . . . 44

10.5 Appendix 5 – Abbreviations used in menu displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

1 Introduction

1.1 At the very beginning

We thank you for having purchased the METTLER TOLEDO O

2

Transmitter 4050 e.

The construction of the O

2

Transmitter 4050 e employs leading edge technology and complies

with safety regulations currently in force. Notwithstanding this, improper use could lead to haz-

ards for the user or a third-party, and/or adverse effects on the plant or other equipment. There-

fore, the operating instructions must be read and understood by the persons involved before

work is started with the O

2

Transmitter 4050 e.

This instruction manual identifies safety instructions and additional information by means of the

following symbols:

– This symbol draws attention to safety instructions and warnings of potential danger which,

if neglected, could result in injury to persons and/or damage to property.

– This symbol identifies additional information and instructions which, if neglected, could lead

to inefficient operation and possible loss of production.

The instruction manual must always be stored close at hand, in a place accessible to all people

working with the O

2

Transmitter 4050 e.

If you have questions, which are not or insufficiently answered in this instruction manual, please

contact your METTLER TOLEDO supplier. He will be glad to assist you.

1.2 Intended use

METTLER TOLEDO O

2

Transmitter 4050 e are intended solely for dissolved oxygen and temper-

ature measurement, as described in this instruction manual.

Any other use, or use not mentioned here, that is incompatible with the technical specifications

is deemed inappropriate. The operator is solely responsible for any damage arising from such

use.

Other prerequisites for appropriate use include:

– observing the instructions, notes and requirements set out in this instruction manual.

– observing all local safety regulations concerning safety at work.

– observing all information and warnings in the documentation dealing with the products used

together with the transmitter (housings, sensors, etc.).

– observing the prescribed environmental and operational conditions.

O

2

Transmitter 4050 e 5

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

1.3 Safety intsructions

– The O

2

Transmitter 4050 e should be installed and operated only by personnel familiar with

the transmitter and who are qualified for such work.

–A defective transmitter must neither be installed nor put into service.

– The O

2

Transmitter 4050 e must only be operated under the specified operating conditions

(see section 8).

– The O

2

Transmitter 4050 e must not be repaired by the customer.

– The O

2

Transmitter 4050 e must only be opened to replace the unit fuse. This work must be

carried out only by personnel familiar with the transmitter and who are qualified for such work.

Make sure the mains cable is separated from the power supply before opening the unit.

– No modifications to the O

2

Transmitter 4050 e are allowed. The manufacturer/supplier accepts

no responsibility for damage caused by unauthorised modifications. The risk is borne entire-

ly by the user.

6 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

2Product description

2.1 Description of unit

The METTLER TOLEDO O

2

Transmitter 4050 e is used for measuring dissolved oxygen ( in % sat-

uration, mg/l or ppm) and temperature values. The dissolved oxygen values can be measured

using limit or P/PI control.

The transmitter is available in two versions, one for panel mounting and one for wall mounting

in a enclosure. The transmitter can be used for applications such as water treatment and moni-

toring, chemical and food processing, clean and wastewater control and fish farming.

This transmitter has many user-friendly and safety features which include:

• Menu-driven program that simplifies set-up.

• Built-in memory backup to ensure that calibration and other information are not erased if pow-

er supply fails.

• Push-button for calibration and electrode offset adjustment from the keypad.

• Automatic temperature compensation (ATC).

• Manual temperature compensation setting without the ATC probe, with independent setting for

calibration and process temperature.

•Two galvanically isolated current outputs 0/4...20mA.

•0 to 1999 seconds time delay adjustment on all relays – minimizes false alarms.

• Separately adjustable high and low set-point hysteresis (dead bands) prevent chattering of

relays around the set points.

• Three control modes: limit controller, P controller and PI controller (P/PI controller as pulse

length or pulse frequency).

• Large dual display LCD for easy reading with clear multiple annunciators, alarm status, op-

erational and error messages.

•Two switching contacts as set-point relays.

• Separate alarm relay alerting you to set point limits exceeded for a certain time and if the NTC

wires are broken or disconnected during the ATC function.

•Wash relay.

• Hold function to freeze output current (0/4...20mA) and release control relays.

• LED indicators signal control activities to visually monitor transmitter status from a distance.

•Protection against electromagnetic interference.

• Back lighted and UV light protected LC display.

O

2

Transmitter 4050 e 7

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

2.2 Measurement and control system

A typical measurement system consists of:

• an O

2

4050 e series transmitter

• an O

2

sensor with integrated or separate temperature sensor

• an appropriate O

2

measurement cable

• an immersion, flow or process assembly

•a final control element such as pump or valve

•a chart recorder

Housings and

Sensors

Alarm/Siren

System

Chart Recorder

O

2

Transmitter 4050 e

Measurement Cable

Power Mains

(80 – 250 VAC)

0/4 – 20 mA

O

2

4050 e

8 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

Cal

Rel

Enter

Rel

M

ode

Rel

O

2

4050 e

C

a

l

E

n

te

r

R

e

l

M

o

d

e

R

e

l

E

S

C

O

2

4

0

5

0

e

2.3 Unit overview

Wall mounting version

Panel mounting version

O

2

Transmitter 4050 e 9

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

2.3.1 Display Overview

The LC display shows two alpha-numerical fields for parameters and measured values as well

as various mode and status indicators.

SETUP MEAS CAL

AT C

READY

HOLD

ERR

°C°F

mg/l

ppm

pH%

-8.8.8.8

Mode indicators:

– MEAS: Measurement mode

– SETUP: Set-up mode

– CAL: Calibration mode

Status indicators:

– READY: Visible after successful calibration

– HOLD: Relay position and current output are frozen

– ATC: Visible in ATC (Automatic Temperature Compen-

sation) mode. Not visible in the Manual temperature

compensation mode. “ATC” flashes if the temperature

probe is faulty in its ATC mode

– ERR: Error or alarm indicator

2.3.2 Key functions

Key Description

• Enter Calibration mode (requires access code)

• Enter Set-up mode (requires access code)

• Access sub functions (parameters) within a function group of Set-up mode

• Confirm (store) set-up parameters and numerical values

• Start calibration in Calibration mode

• Select function group in the Set-up mode.

• Set parameters and numerical values

(if key is pressed continuously, the setting speed increases)

• Control the relays in MANUAL relay operation

• Returns to “Measurement mode” when both keys are pressed simultaneously

• Display limit values for SP1 and SP2 and settings for wash contact in AUTO re-

lay operation

•Toggle between RELAY A, RELAY B or Wash relay in MANUAL relay operation

• Switch from AUTO to MANUAL relay operation (requires access code)

10 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

2.3.3 LED indicators

Relay indicators

If REL key is pressed the LED (A, B or W) indicates to which Relay (A,

B or Wash) the displayed limit values refer

Relay mode indicators

Auto LED lights if relay operation is set to automatic mode.

Man LED lights if relay operation is set to manual mode.

Relay status indicators

Alarm: LED lights if limit value is exceeded or the ATC probe fails.

Rel A: LED lights green if measured value is within limit for Relay A

LED lights red if measured value exceeds limit for Relay A

Rel B: LED lights green if measured value is within limit for Relay B

LED lights red if measured value exceeds limit for Relay B

Rel W: LED lights if cleaning cycle is on.

2.3.4 Security codes

The access to Calibration mode, Setup mode and Manual relay operation mode is protected

with security codes. The security codes are set at the factory and cannot be changed by the user.

The following security codes are used:

Security code Mode/Description

000 View only mode to view actual settings

11 Calibration mode to start calibration

22 Setup mode to configure parameters

22 Manual relay operation to switch relay operation mode from automatic to

manual

O

2

Transmitter 4050 e 11

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

MEAS

100.0

pH%

°C

25.0

000

CCD

000

SCD

EnterEnter

Enter

Cal

** ***

Enter

SETUP

OFS

HOLD

SETUP

SET

HOLD

°C°F

SETUP

SP1

HOLD

SETUP

SP2

HOLD

SETUP

CNTR

HOLD

SETUP

CUR.1

HOLD

SETUP

CUR.2

HOLD

SETUP

WASH

HOLD

SETUP

CNFG

HOLD

SETUP

CAL

HOLD

DO

Cal

Enter

Offset setting

--> see section 6.2

Calibration

--> see section 5

Unit settings

--> see section 6.9

Wash contact settings

--> see section 6.8

Current output 2 settings

--> see section 6.7

Current output 1 settings

--> see section 6.6

Controller settings

--> see section 6.5

Relay B (set point 2) settings

--> see section 6.4

Relay A (set point 1) settings

--> see section 6.4

Temperature settings

--> see section 6.3

** CCD “000”= Check calibration parameters (View only mode)

** CCD “11”= Calibration

*** SCD “000”= Check setup parameters (View only mode)

*** SCD “22”= Setup mode

2.3.5 Menu overview

12 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

Holes for wall

mounting (2x)

Note: all dimensions in mm

For Pg13.5 cable glands

Pg13.5 (3 pcs.)

approx. 14

Holes for panel

mounting (4x) or for

post mounting (4x)

39

42.4

21.1

27.5

108.5

144

78

80

32

90

3 Assembly and installation

3.1 Mounting the unit

Wall mounting version

Transmitter housing for wall mounting: protection class IP 65

O

2

Transmitter 4050 e 13

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

Flat gasket (1mm)

(to be inserted by customer)

Note: The taped corners have to be on top

92

56

32

Panel cut-out

max. 175

max. 45

96

92 +0.5

Panel mounting version

Transmitter housing for panel mounting: protection class IP 54 (front), IP 40 (housing)

14 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

3.2 Connection diagram

Connectors wall mounting version

TEMP

29 28 31

22 23

30 20 19 21 26 25 24 14 13 2 13

654789101112

Current

OP 2

Current

OP 1

HOLD E N L

REL A REL B WASH RELAY ALARM RELAY

GND +12 V

+–+–

E

A

CELL

K

TEMP

29 28 31

22 23

30 20 19 21 26 25 24 14 13 2 13

654789101112

Current

OP 2

Current

OP 1

HOLD E N L

REL A REL B WASH RELAY ALARM RELAY

GND +12 V

+–+–

E

A

CELL

K

O

2

Transmitter 4050 e 15

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

Connectors panel mounting version

REL A REL B WASH RELAY

HOLD

CELL

KA

ALARM RELAY

E

TEMP

OP1+

OP1–

OP2+

OP2–

+12 V

GND

12312

2

11

1

10

2

9

1

8

2

7

1

6

1

5

2

4

3

LNE

14 13151617181920212223242527 2628293031

J5

VP cable connection

VP cable Transmitter terminal

A transparent (Cathode) K (23)

B red (Anode) A (22)

E white (T1) RTD (26)

F green (T2) RTD (24)

G green/yellow (cable shield) E (21)

Note: Grey and blue wire are not connected

16 O

2

Transmitter 4050 e

O

2

Transmitter 4050 e © 07/02 Mettler-Toledo GmbH, CH-8606 Greifensee

52 121 142 Printed in Switzerland

The mode indicator “MEAS” at the top of the display indicates that the

transmitter is in Measurement mode. The upper alpha-numerical dis-

play shows the measured O

2

value (in %, mg/l or ppm), while the

lower display shows the temperature value (in °C or °F).

The annunciators “%”, “mg/l” or “ppm” at the upper right side of the

display indicate the current measurement mode setting whether the

transmitter is set for %, mg/l or ppm measurement.

MEAS

100.0

pH%

°C

25.0

From Measurement mode you can access Calibration mode and Setup mode by pressing the

CAL key or ENTER key followed by the corresponding security code. For detailed information re-

fer to section 5 “Calibration mode” or section 6 “Setup mode”, respectively.

By pressing the REL key in Measurment mode you can view the actual relay set points. By press-

ing the REL MODE key in Measurment mode you can switch relay operation mode from auto-

matic to manual. For detailed information refer to section 7 “Relay operation”.

4 Normal operation

Measurement mode

When the transmitter is powered on, the display first shows all segments briefly, then the trans-

mitter automatically enters into the Measurement mode.

Please note: To guarante accurate readings the measuring system (transmitter and sensor) must

be calibrated.

O

2

Transmitter 4050 e 17

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

5 Calibration Mode

You can access the Calibration mode directly from the Measurement mode by pressing the CAL

key and entering the Calibration security code “11”. Calibration mode may also accessed via the

Setup mode (see section 6.1).

5.1 Entering Calibration mode

Enter

MEAS

100.0

pH%

°C

25.0

SETUP

OFS

HOLD

SETUP

CAL

HOLD

DO

11

CCD

22

SCD

Enter

Cal

Enter

1-point or 2-point calibration

--> see section 5.2

1. While in Measurement mode press the CAL key (direct access) or ENTER key (access via

Setup mode).

2. If CAL key was pressed: The display prompts you to enter the calibration security code. Press

the ▲ or ▼ key to set the calibration security code to “11”, then press the ENTER key to con-

firm the calibration security code.

If ENTER key was pressed: The display prompts you to enter the security code. Press the ▲

or ▼ key to set the security code to “22”. Press the ENTER key to confirm the security code,

then press the ▲ or ▼ key to select the calibration subfunction.

The display shows “CAL DO”. To start calibration refer to the corresponding section (see illustra-

tion above).

Note: to exit Calibration mode at any time press the ▲ and ▼ key simultaneously (escape).

The transmitter returns to the Measurement mode and the old calibration values remain active.

The calibration security code automatically resets from “11” to “000” after the transmitter returns

to Measurement mode.

18 O

2

Transmitter 4050 e

O

2

52 121 142 Printed in Switzerland

5.2 Calibration

Note: Calibration is always carried out in the units (%, mg/l or ppm) selected in the Setup mode.

The O

2

transmitter allows a 1-point or 2-point calibration.

1-point calibration

1. Enter Calibration mode as described in section 5.1. The display shows “CALDO”.

2. Press the ENTER key. The display shows “1-PT CAL” (1-point calibration). Press the ENTER

key to confirm 1-point calibration.

3. Press the ▲ or ▼ key to set the relative humidity. Press the ENTER key to confirm.

4. Press the ▲ or ▼ key to select the desired unit for barometric pressure (“BAR”, “mmHG” or

“PSI”). Press the ENTER key to confirm.

5. Press the ▲ or ▼ key to set the barometric pressure according to the preselected unit. Press

the ENTER key to confirm.

6. Put sensor in the calibration solution or air. The temperature compensated sensor current (in

nA) will be displayed. The “CAL” and “ELECTRODE SYMBOL“ start flashing. Once the reading

stabilizes, the flashing symbols disappear and “READY” comes on. Press the ENTER key to

confirm the value.

7. Default calibration values for saturation or concentration are shown. Press the ▲ or ▼ key

to select the desired saturation (“SAT %”) or concentration (“Con ppm” or “Con mg/l”). Press

the ENTER key to confirm.

8. The transmitter will return to the Measurement mode.

Note: If you entered the Calibration mode from the Setup mode, the transmitter will return to

the setup menu.

Note: If there is a calibration error the transmitter displays “ERR”. In this case, press the ▲ and

▼ keys simultaneously (escape) to restart the calibration beginning from step 1.

SETUP

HOLD

Enter Enter

Enter

CAL

DO

HOLD

100

HOLD

RH

pH%

CAL

Enter Enter

SETUP

1-PT

CAL

SETUP

2

1

3

ATC

MEAS

100.0

%

°C

25.0

BAR

HOLD

PRES

CAL

SETUP

1.015

HOLD

BAR

CAL

SETUP

Enter

65.3

HOLD

nA

CAL

SETUP

Enter

100.0

HOLD

SAT

CAL

SETUP

mmH9

HOLD

PRES

CAL

SETUP

PSI

HOLD

PRES

CAL

SETUP

4

5

6 7 8

READY

pH%

O

2

Transmitter 4050 e 19

2

Transmitter 4050 e

Printed in Switzerland 52 121 142

Note: When calibrating with manual temperature compensation, the transmitter automatically

changes from the preset process temperature to the calibration temperature. After leaving the Cali-

bration mode, the transmitter switches back to the process temperature (for setting the calibrati-

on temperature and the process temperature, see section 6.3).

2-point calibration

1. Enter Calibration mode as described in section 5.1. The display shows “CALDO”.

2. Press the ENTER key. The display shows “1-PT CAL” (1-point calibration). Press the ▲

or ▼ key to select “2-PT CAL” (2-point calibration). Press the ENTER key to confirm 2-

point calibration.

3. Press the ▲ or ▼ key to set the relative humidity. Press the ENTER key to confirm.

4. Press the ▲ or ▼ key to select the desired unit for barometric pressure (bar, mmHG or PSI).

Press the ENTER key to confirm.

5. Press the ▲ or ▼ key to set the barometric pressure according to the preselected unit. Press

the ENTER key to confirm.

6. Put sensor in zero point solution or nitrogen. The temperature compensated sensor current

for zero point (in nA) will be displayed. The “CAL” and ”ELECTRODE SYMBOL” start flashing.

Once the reading stabilizes, the flashing symbols disappear and “READY” comes on. Press

the ENTER key.

7. Press the ▲ or ▼ key to accept new zero current with “YES” or to reject the new calibration

value with “NO”. Press the ENTER key to confirm your selection.

Note: Accepting the zero point will reset the zero offset settings made in OFS menu.

SETUP

HOLD

Enter Enter

Enter

CAL

DO

HOLD

100

HOLD

RH

pH%

CAL

Enter Enter

SETUP

2-PT

CAL

SETUP

2

1

3

ATC

MEAS

100.0

%

°C

25.0

BAR

HOLD

PRES

CAL

SETUP

1.015

HOLD

BAR

CAL

SETUP

Enter

0.0

HOLD

nA

CAL

SETUP

Enter

2ND

HOLD

PNT

CAL

SETUP

mmH9

HOLD

PRES

CAL

SETUP

PSI

HOLD

PRES

CAL

SETUP

4

5

6

Enter

100.0

HOLD

SAT

CAL

SETUP

10

Enter

YES

HOLD

-0.0

CAL

SETUP

7

NO

HOLD

-0.0

CAL

SETUP

7

8

Enter

102.1

HOLD

nA

CAL

SETUP

9

11

READY

pH%

20 O

2

Transmitter 4050 e

O

2

52 121 142 Printed in Switzerland

8. The display shows “2ND PNT”. Press the ENTER key to proceed with the calibration of slope.

9. Put sensor in the calibration solution or air. The temperature compensated sensor current (in

nA) for the second point will be displayed. The “CAL” and ”ELECTRODE SYMBOL” start flas-

hing. Once the reading stabilizes, the flashing symbols disappear and “READY” comes on.

Press the ENTER key.

10.Default calibration values for saturation or concentration are shown. Press the ▲ or ▼ key

to select the desired saturation (“SAT %”) or concentration (“Con ppm” or “Con mg/l”). Press

the ENTER key to confirm.

11.The transmitter will return to the Measurement mode.

Note: If you entered the Calibration mode from the Setup mode, the transmitter will return to

the setup menu.

Note: If there is a calibration error the transmitter displays “ERR”. In this case, press the ▲ and

▼ keys simultaneously (escape) to restart the calibration beginning from step 1.

Note: When calibrating with manual temperature compensation, the transmitter automatically

changes from the preset process temperature to the calibration temperature. After leaving the Cali-

bration mode, the transmitter switches back to the process temperature (for setting the calibrati-

on temperature and the process temperature, see section 6.3).

Page is loading ...

Mettler Toledo O2 transmitter O2 4050e Operating instructions

Mettler Toledo O2 transmitter O2 4050e Operating instructions

Related papers

Other documents