2. V-ZUG
  3. 269
269

V-ZUG 269, 266 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the V-ZUG 269 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the maximum height for installing the device above sea level?
    If I lose my emergency release tool, what can I use instead?
    What should I do if the error message 'U1' appears on the display?
    How do I start the stability check for models 268 and 269?
    How do I set the time and date on models 265 and 266?
Installation instructions
Washing machine «Front loader»
One-family household
J265.113-4
18.4.12 FUW
1
These installation instructions apply to the models: 265, 266, 268, 269
A Open the drain tray at bottom front of appliance.
For details see «1. Open the appliance door (without power)».
– The identification plate is located at bottom (see arrow).
Installation set W3.6278
The installation set is located in the drum of the washing machine and can be taken out after opening the appliance door (see first
installation step).
The installation set includes:
Installation plate W3.8503
incl. screw material (S)
The installation plate is fixed to the bottom of the appliance.
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
Identification plate
Installation accessories supplied
Designation Number See installation step
Rubber stoppers 3 2. Remove the transportation locks
Combination spanner 1
2. Remove the transportation locks
4. Levelling
Double-sided adhesive tape 1 3. Positioning the installation plate
Exterior drain hose 1
5. Plumbing inWire hose clamp 1
Hose clip 1
S
Installation instructions
Washing machine «Front loader»
One-family household
J265.113-4
18.4.12 FUW
2
1. Remove the screws E of the 3 transportation locks F.
2. Push the transportation lock up and out.
3. Plug the holes with the rubber stoppers G.
Installation
Work steps 1–7 must be carried out in full in the order specified.
1. Open the appliance door (without power)
Right door opening Left door opening
1a Open the drain
tray A by pressing
it at the bottom.
or
1b Remove quick
operating instruc-
tions B from deter-
gent dispenser
drawer C and open
the drain tray A.
2 Fold the drain tray A
right down and
remove it.
Remove emergency
release tool D from
its bracket.
A Insert the tool D into the opening and turn in the
direction of the arrow (see arrow on appliance).
2. Remove the transportation locks
The transportation locks F on the rear side have to be removed before using the appliance for the first time.
1b 21a
A
B
C
D
A
B
A
GE
1.
2.
3.
F
Installation instructions
Washing machine «Front loader»
One-family household
J265.113-4
18.4.12 FUW
3
A Raise the appliance slightly at the front and pull it forward, away from the installation plate.
A Secure the installation plate to the location you wish to install the appliance using 4 screws. On smooth and clean floors, you can
affix the installation plate (double-sided adhesive tape supplied)
A Dampen the mounting slots on the installation plate with water.
Free-standing position
* This only applies if no plumbing fittings are to be installed behind the appliance.
3. Positioning the installation plate
Use the installation plate to install the appliance. This plate fixes the appliance in position (for both free-standing appliances
and appliances placed in a niche).
If a tumble dryer and a washing machine are positioned side by side, keep a distance of min. 5 mm between installation plates
and min. 3 mm to walls.
Positioning in a niche
A Centre the installation plate in the niche.
H * Depth of niche including appliance door: min. 630 mm
J * Depth of niche without appliance door: min. 600 mm
min. 3
597
595
505
min. 550 *
50
min. 5
min. 5
25
J
H
Appliance door
Installation plate
Niche
H, J
min. 600
Niche width
Cut-out for lateral
connections, to the
left or right side
min. 100 × 100 mm
Niche height
min. 860 mm!
Installation instructions
Washing machine «Front loader»
One-family household
J265.113-4
18.4.12 FUW
4
Höhe einstellen
Tools: Combination spanner K (supplied) and spirit level L
Rear adjuster feet:
Maximum height adjustment of 14 mm / 1.5 mm per turn
A Align the appliance vertically – with the combination spanner.
Front adjuster feet:
A Slide appliance onto installation plate.
A Align the appliance vertically – with the combination spanner.
– Appliance must not wobble.
Water inlet
䡲 Only cold water G¾", possible pressure range 0.1–0.6 MPa (1–6 bar).
䡲 The appliance must not be connected to a mixer tap or a continuous flow boiler!
A The tap seal seat must be clean and flat.
A Install the hose without bending or twisting it.
A Check the seal.
A Where accessible, also fix hose to rear wall with adhesive base (see figure «Water outlet»).
Water outlet
A When installing the drain hose, protect it against damage and bending (hot suds will flow through it).
A Assemble the hose clip for all connection variants.
A If draining into the bath tub, sink etc. use the bend (hose clip) to fix the end of the hose.
A The drain pump can pump to a max. height of 1.2 m.
4. Levelling
To ensure fault-free operation, the appliance must be perfectly vertical with all 4 feet standing firmly on the floor and must not
wobble.
5. Plumbing in
Always observe the local water supply authority’s regulations.
Any old water supply and drain hoses must always be replaced with new hoses.
L
K
max. 700
min. 350
Hose clamp
Drain hose
Rubber connector
Shorten drainage hose to
required length.
Cannot shorten drainage hose!
ø exterior 28.0 mm
ø interior 21.5 mm
Hose clip
(bend)
1.5 m
Adhesive
base
Adhesive
base
Installation instructions
Washing machine «Front loader»
One-family household
J265.113-4
18.4.12 FUW
5
➤ Refer to the identification plate for specifications for the required mains voltage, current type and fuses.
➤ Application height of the appliance: up to max. 2000 m above sea level
➤ Information on the necessary mains voltage, type of current and fuse protection is to be obtained from the identification plate.
Connection cable
Error message «U1»
Electrical connections
Electrical connections must made by trained electricians in accordance with the guidelines and standards for low voltage
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
The connection cable may only be replaced by the manufacturer, the manufacturer’s customer services or a similarly qualified
person.
400 V 2N~ 50 Hz, 10 A 230 V~ 50 Hz, 10 A 230 V~ 50 Hz, 16 A
Colour code
L2
L1
black
brown
blue
yellow/green
The appliance detects an overvoltage. Control wiring, in particular the neutral conductor.
N
L2
L1
4 × 1 mm²
3 × 1 mm²
N
L1
N
L1
3 × 1,5 mm²
N
Installation instructions
Washing machine «Front loader»
One-family household
J265.113-4
18.4.12 FUW
6
Models 268, 269 (language setting/stability check/time and date)
1. Plug the appliance in at the mains or turn the wall switch on.
– The appliance switches on.
2. Remove the drum contents and then close the appliance door.
3. Turn the water tap on.
4. The language preset at the factory appears in the display.
A Set the desired language using the left-hand flashing button and confirm using the right-hand flashing (OK) button.
5. appears in the display.
6. To start the stability check, press the right-hand flashing (OK) button
appears for about 2 minutes in the display.
7. appears in the display.
A Check the stability of the appliance. The appliance must stand perfectly vertically with all 4 feet firmly on the floor and must not
wobble.
8. Press the button to complete the initial set-up of the appliance.
appears in the display.
– The spinning sequence is finished. The appliance is then drained.
– The display goes dark.
9. To set the time and date, press any main programme button and follow the instructions.
10.If necessary, repeat levelling as explained under point 4. The stability check can be repeated any number of times:
A Depress the , and buttons simultaneously for 5 seconds.
11.The appliance is ready for operation.
Models 265, 266 (stability check)
1. Plug the appliance in at the mains or turn the wall switch on.
– The appliance switches on.
2. Remove the drum contents and then close the appliance door.
3. Turn the water tap on.
4. Depress the , and buttons simultaneously for 5 seconds.
– The spinning sequence is carried out.
5. appears after about 2 minutes in the display.
A Check the stability of the appliance. The appliance must stand perfectly vertically with all 4 feet firmly on the floor and must not
wobble.
6. Press the button to complete the initial set-up of the appliance.
– The spinning sequence is finished. The appliance is then drained.
7. If necessary, repeat levelling as explained under point 4. As described above, the stability check can be repeated any number of
times.
8. The appliance is ready for operation.
6. Using for the first time
Deliberately strong vibrations are produced during the stability check in order to test whether the appliance is firmly seated.
Stability check
abort OK
Create unbalanced load
please wait …
Check stability
Create unbalanced load
finishing …
/