IM1609 10/08
Installation Information
Water Piping Connections
Electrical
Startup Procedures
Troubleshooting
Preventive Maintenance
Envision Console Installation Manual
Geothermal/Water Source Heat Pumps
• R-410A Refrigerant
• 0.75-1.5 Ton Single Speed
CONSOLE
2
ENVISION CONSOLE INSTALLATION MANUAL
Table of Contents
Model Nomenclature........................................................... 3
General Installation Information ................................................. 4
Dimensional Data............................................................ 5-11
Installation Steps ........................................................... 12-15
System Cleaning and Flushing...................................................16
Open Loop Ground Water Systems ..............................................17
Electrical Connections .........................................................18
Auxiliary Heat Ratings .........................................................18
Unit Electrical Data ............................................................19
Fan Performance Table .........................................................19
Wiring Schematics.........................................................20-24
Envision Console Controls .................................................. 25-39
Unit Startup Notes............................................................40
Unit Startup Checklist/Unit Startup Steps.........................................41
Unit Operating Parameters .................................................... 42
Unit Operating Limits .........................................................42
Startup/Troubleshooting Form .................................................43
Pressure Drop................................................................44
Preventive Maintenance .......................................................45
Replacement Procedures ......................................................45
3
ENVISION CONSOLE INSTALLATION MANUAL
Model Nomenclature
CONSOLES
1-2 3 4-5 6 7 8 9 10 11 12 13 14 15-16 17
NC C 09 L 0 1 1 C N N A 1 SS A
Family Vintage
NC = Envision Console A = Current
Non-Standard Option Details
Cabinet Configuration SS = Standard Option
C = Chassis Only
W = Chassis with Cabinet
S = Chassis with Slope Top
E = Chassis with Extended Slope Top
Unit Capacity Air Coil / Insulation Options
MBTUH @ 86
o
F EWT 1 = Formishield / Extended Range
09, 12, 15, 18 2 = Formishield / Standard Range
3 = No Coating / Extended Range
Piping Option 4 = No Coating / Standard Range
L = Left
R= Right (N/A with chassis only) Sound Kit
A = None
Voltage B = Blanket
0 = 208-230/60/1
2 = 265/60/1 Auxilliary Electric heat
N = None
C = 2.0 kW (09-12)*
Unit Control D = 3.0 kW (15-18)*
1 = CCM
2 = Versatec Motorized Oustide Air Damper (Field Installed)
4 = FX10 std. no communication - (only w/ t-stat control option 2) N = None
5 = FX10 w/Open N2 Com Card - (only w/ t-stat control option 2) M = Motorized Damper
6 = FX10 w/Lonworks Com Card - (only w/ t-stat control option 2)
7 = FX10 w/BacNet Com Card - (only w/ t-stat control option 2) Coax Options
C = Copper
Thermostat Control N = Cupronickel
1 = Unit mounted t-stat
2 = Remote wall-mounted t-stat
4
ENVISION CONSOLE INSTALLATION MANUAL
Safety Considerations
WARNING: Before performing service or main-
tenance operations on a system, turn off main
power switches to the indoor unit. If applicable,
turn off the accessory heater power switch. Elec-
trical shock could cause personal injury.
Installing and servicing heating and air conditioning
equipment can be hazardous due to system pressure and
electrical components. Only trained and qualified service
personnel should install, repair or service heating and air
conditioning equipment. Untrained personnel can perform
the basic maintenance functions of cleaning coils and clean-
ing and replacing filters. All other operations should be
performed by trained service personnel. When working on
heating and air conditioning equipment, observe precau-
tions in the literature, tags and labels attached to the unit
and other safety precautions that may apply.
Follow all safety codes. Wear safety glasses and work
gloves. Use a quenching cloth for brazing operations and
have a fire extinguisher available.
Moving and Storage
Move units in the normal “up” orientation. Do not stack
units. When the equipment is received, all items should be
carefully checked against the bill of lading to be sure all
crates and cartons have been received. Examine units for
shipping damage, removing the units from the packag-
ing if necessary. Units in question should also be internally
inspected. If any damage is noted, the carrier should make
the proper notation on the delivery receipt, acknowledging
the damage.
Water Piping
The proper water flow must be provided to each unit when-
ever the unit operates. To assure proper flow, use pressure/
temperature ports to determine the flow rate. These ports
should be located at the supply and return water connec-
tions on the unit. The proper flow rate cannot be accurately
set without measuring the water pressure drop through the
refrigerant-to-water heat exchanger.
All source water connections on commercial units are fit-
tings that accept a male pipe thread (MPT). Insert the con-
nectors by hand, then tighten the fitting with a wrench to
provide a leakproof joint. When connecting to an open loop
(groundwater) system, thread any copper MPT fitting into
the connector and tighten in the same manner as described
above.
Refrigerant Systems
To maintain sealed circuit integrity, do not install service
gauges unless unit opertion appears abnormal. Compare
the change in temperature on the air side as well as the wa-
ter side to the Unit Operating Parameters tables. If the unit’s
performance is not within the ranges listed, and the airflow
and water flow are known to be correct, gauges should
then be installed and superheat and subcooling numbers
calculated. If superheat and subcooling are outside recom-
mended ranges, an adjustment to therefrigerant charge may
be necessary.
General Installation Information
5
ENVISION CONSOLE INSTALLATION MANUAL
NCW09-18
Overall Cabinet
Flat Top
Configuration
A B C D E F G H I J
Width Depth Height Grille Lid
Grille
Length
Grille
Width
in. 45.0 10.8 25.7 9.2 35.0 6.1 2.3 44.1 10.3 4.3
cm. 114.3 27.3 65.2 23.4 88.9 15.6 5.8 112.0 26.0 10.9
in. 50.0 12.3 25.7 9.2 35.0 6.1 3.3 49.1 11.8 4.3
cm. 127.0 31.1 65.2 23.4 88.9 15.6 8.3 124.7 29.8 10.9
09-12
15-18
4
0
5
7
8
1
32
/
6
47:B3@0@/193B 47:B3@0@/193B
@756B@3BC@<
B=>
4@=<B
:34B@3BC@<
23B/7:0
BE7AB3FB3<232
B/00/19/<2
4=@B6C<B7:
B/00@3/9A=44
=<:G0@3/9=44
B/0A/;3A723/A
5@7::3:72/AA6=E<
23B/7:0
BE7AB3FB3<232B/0
0/19/<24=@B6C<B7:
B/00@3/9A=44
=<:G0@3/9=44
B/0A/;3A723/A
5@7::3:72/AA6=E<
0/
@3;=D3>:/AB71AB@7>
4@=;0@=93<B/0/<2
@3>:/13=<0@=93<
3253=4:35/AA6=E<
@3;=D3>:/AB71AB@7>
4@=;0@=93<B/0/<2
@3>:/13=<0@=93<
3253=4:35/AA6=E<
Dimensional Data - Flat Top Cabinet
6
ENVISION CONSOLE INSTALLATION MANUAL
NCS09-18
Overall Cabinet
Slope Top
Configuration
A B C D E F G H I J
Width Depth Height Grille Lid
Grille
Length
Grille
Width
in. 45.0 11.1 28.6 9.2 35.0 6.1 2.8 44.1 10.3 4.3
cm. 114.3 28.2 72.6 23.4 88.9 15.6 7.2 112.0 26.0 10.9
in. 50.0 12.6 29.1 9.2 35.0 6.1 2.5 49.1 11.8 4.3
cm. 127.0 32.0 73.9 23.4 88.9 15.6 6.4 124.7 29.8 10.9
09-12
15-18
@3;=D3>:/AB71AB@7>
4@=;0@=93<B/0/<2
@3>:/13=<0@=93<
3253=4:35/AA6=E<
6
7
8
1
4
3
/
2
5
0
@756B@3BC@<
B=>
4@=<B
:34B@3BC@<
23B/7:0
BE7AB3FB3<232B/0
0/19/<24=@B6C<B7:
B/00@3/9A=44
=<:G0@3/9=44
B/0A/;3A723/A
5@7::3:72/AA6=E<
23B/7:/
BE7AB3FB3<232B/0
0/19/<24=@B6C<B7:
B/00@3/9A=44
=<:G0@3/9=44
B/0A/;3A723/A
5@7::3:72/AA6=E<
@3;=D3>:/AB71AB@7>
4@=;0@=93<B/0/<2
@3>:/13=<0@=93<
3253=4:35/AA6=E<
0
/
47:B3@0@/193B
47:B3@0@/193B
Dimensional Data - Slope Top Cabinet
7
ENVISION CONSOLE INSTALLATION MANUAL
NCE09-18
@3;=D3>:/AB71AB@7>
4@=;0@=93<B/0/<2
@3>:/13=<0@=93<
3253=4:35/AA6=E<
Overall Cabinet
Ext. Slope Top
Configuration
A B C D E F G H I J
Width Depth Height Grille Lid
Grille
Length
Grille
Width
in. 50.0 12.6 29.1 9.2 35.0 6.1 2.4 49.1 12.0 4.3
cm. 127.0 32.0 73.9 23.4 88.9 15.6 6.1 124.7 30.5 10.9
in. 55.0 12.6 29.1 9.2 35.0 6.1 2.5 54.1 11.8 4.3
cm. 139.7 32.0 73.9 23.4 88.9 15.6 6.4 137.4 29.8 10.9
09-12
15-18
47:B3@0@/193B47:B3@0@/193B
/
2 3
1
6
7
8
4
0
5
/
0
@756B@3BC@< B=>
4@=<B
:34B@3BC@<
23B/7:0
BE7AB3FB3<232B/0
0/19/<24=@B6C<B7:
B/00@3/9A=44
=<:G0@3/9=44
B/0A/;3A723/A
5@7::3:72/AA6=E<
23B/7:/
BE7AB3FB3<232B/0
0/19/<24=@B6C<B7:
B/00@3/9A=44
=<:G0@3/9=44
B/0A/;3A723/A
5@7::3:72/AA6=E<
@3;=D3>:/AB71AB@7>
4@=;0@=93<B/0/<2
@3>:/13=<0@=93<
3253=4:35/AA6=E<
Dimensional Data - Extended Slope Top Cabinet
8
ENVISION CONSOLE INSTALLATION MANUAL
1=<B@=:>/<3:
@3;=D34=@/113AA
B=1=<B@=:0=F
2/;>3@=<=44AE7B16
1=;>@3AA=@
/113AA>/<3:
@3;=D324=@
1:/@7BG
0=B6A723A
3:31B@7163/B;=23
<=@;/:0=7:3@:3AA
AE7B16=>B7=</:
4/<=>B7=<AE7B16
=>B7=</:0/19>:/B3
@3?C7@324=@
2/;>3@7<AB/::/B7=<
=CBA723/7@
2/;>3@=>B7=<
473:27<AB/::32
:=ED=:B/53
B3@;7</:A
4F@3;=B3E/::
AB/B=>B7=<A=<:G
=>B7=</:
4CA32
<=<4CA32
27A1=<<31B
=>B7=</:
0/::D/:D3A
=>B7=</:
6=A397BA
1=<23<A/B3
2@/7<1=<<31B7=<
47:B3@
6/<2G0=F
Dimensional Data - Right Return Controls Detail
9
ENVISION CONSOLE INSTALLATION MANUAL
0:=E3@/113AA>/<3:
1=;>@3AA=@
/113AA>/<3:
!%&&
'$
&#
% "
#
!&
#
!&
"!%
'!&
!&
47:B3@
1=<B@=:>/<3:
# #
$"
&$
!
$
#
%&
"#
%'
"#
"
#
"
#""
#&
1=<23<A/B3
2@/7<1=<<31B7=<
E/B3@=CB Þ4>B
E/B3@7< Þ4>B
=>B7=</:0/19>:/B3
1=;>@3AA=@
/113AA>/<3:
"!!%
&
%
' #
!#
!'
!#!
#$#
$#
'&!
#"
$"
"
!
!$
$$
%
%#
%
##
"
2/;>3@=>3<7<5
<1'
0:=E3@/113AA>/<3:
1=;>@3AA=@
/113AA>/<3:
" &&
&'
!"
&$"
#
!&
#
!&
"!
&&&
$
47:B3@
1=<B@=:>/<3:
# #
$"
&$
%#
'&
#
!#
"#
"
#
$
# !
'#
"'#
1=<23<A/B3
2@/7<1=<<31B7=<
E/B3@=CB Þ4>B
E/B3@7< Þ4>B
=>B7=</:0/19>:/B3
1=;>@3AA=@
/113AA>/<3:
"& #
$
!!
&!&
%&
''
!'
!#!
#&
$##
#&
$
"
&
!'
&!
%#
%
#"
!%
2/;>3@=>3<7<5
<1#&
Dimensional Data - Right Return Chassis
Data = inches (cm)
10
ENVISION CONSOLE INSTALLATION MANUAL
:=ED=:B/53
B3@;7</:A
4F@3;=B3E/::
AB/B=>B7=<A=<:G
=>B7=</:
4CA32
<=<4CA32
27A1=<<31B
=>B7=</:
0/::D/:D3A
=>B7=</:
6=A397BA
1=<23<A/B3
2@/7<1=<<31B7=<
47:B3@
6/<2G0=F
=>B7=</:
3:31B@7163/B
=>B7=</:0/19>:/B3
@3?C7@324=@
2/;>3@7<AB/::/B7=<
=CBA723/7@
2/;>3@=>B7=<
473:27<AB/::32
1=<B@=:>/<3:
@3;=D34=@/113AA
B=1=<B@=:0=F
2/;>3@=<=44AE7B16
1=;>@3AA=@
/113AA>/<3:
@3;=D324=@
1:/@7BG
0=B6A723A
3:31B@7163/B;=23
<=@;/:0=7:3@:3AA
AE7B16=>B7=</:
4/<=>B7=<AE7B16
Dimensional Data - Left Return Controls Detail
11
ENVISION CONSOLE INSTALLATION MANUAL
'!&
!&
&#
% "
#
!&
#
!&
"!%
!%&&
'$
0:=E3@/113AA>/<3:
1=;>@3AA=@
/113AA>/<3:
47:B3@
1=<B@=:>/<3:
#
!
$
"#
"
&$
#
# #
$"
"
#""
#&
%&
"#
%'
1=<23<A/B3
2@/7<1=<<31B7=<
E/B3@=CB Þ4>B
E/B3@7< Þ4>B
&
%
!'
!#!
' #
!#
%#
%
!
!#
$$
%
##
"
=>B7=</:0/19>:/B3
1=;>@3AA=@
/113AA>/<3:
2/;>3@=>3<7<5
"!!%
$
"
#$#
$#
'&!
#"
<1'
&&&
$
!"
&$"
#
!&
#
!&
"!
" &&
&'
0:=E3@/113AA>/<3:
1=;>@3AA=@
/113AA>/<3:
47:B3@
1=<B@=:>/<3:
#
%#
$
"#
"
&$
#
# #
$"
$
# !
'#
"'#
!#
1=<23<A/B3
2@/7<1=<<31B7=<
E/B3@=CB Þ4>B
E/B3@7< Þ4>B
!!
&!&
!'
!#!
%&
''
%#
%
&
!'
&!
##
"
=>B7=</:0/19>:/B3
1=;>@3AA=@
/113AA>/<3:
2/;>3@=>3<7<5
"& #
$
$
"
#&
$##
#&
<1#&
Dimensional Data - Left Return Chassis
Data = inches (cm)
12
ENVISION CONSOLE INSTALLATION MANUAL
Installation Steps
Step 1: Unpack Equipment and Inspect for Damage
Step 2: Determine Equipment Location
Choose level flooring surface (Correctable with shims. Do not pitch towards drain.)•
Location of wall support and fasteners required to secure chassis backplate.•
Easy access for both installation and service. •
Consider availability and ease of wiring, water piping and condensate drain.•
No obstructions to block airflow in front of the unit.•
Step 3: Mark Unit Position
Ensure that floor is level. If shims are required, make sure that the entire compressor compartment area is uniformly •
shimmed and that the backplate mounting height is increased by the thickness of the shims used.
Position backplate in desired equipment location. To further reduce the operating sound level of the unit, 1/8-inch thick •
rubber matting may be placed under the chassis to eliminate vibration on hard flooring surfaces. (Make sure back plate
is level).
Mark and cut floor or wall penetrations for electrical wiring, water and condensate piping.•
Optional Electrical Disconnect and Motorized Outside Air Damper
Mark and cut wall penetrations for field fabricated outside air duct sleeve.•
Align mounting holes with backplate and attach with screws supplied.•
1=<A=:3
1/07<3B
1=<A=:3
16/AA7A
1=<23<A/B3
2@/7<:=1/B7=<
=>B7=</:6=A3A
0/::D/:D3A
=>B7=</:
>B>:C5A
=>B7=</:
E/B3@
=CB
E/B3@
7<
1=<A=:31/07<3B
0/19>:/B3
=>B7=</:
E/::>3<3B@/B7=<
4=@E/B3@1=<<31B7=<
4:==@>3<3B@/B7=<
4=@E/B3@1=<<31B7=<
4CA323:31B@71/:
27A1=<<31B=>B7=</:
;=B=@7H32
2/;>3@
=>B7=</:
;=B=@7H32
2/;>3@
=>3<7<5
Figure 1
13
ENVISION CONSOLE INSTALLATION MANUAL
Installation Steps (cont.)
Step 4: Provide Water and Condensate Drain Connections
A two-pipe reverse return piping configuration is recommended as it equalizes the piping circuit lengths and delivers •
even water flow to each unit. A direct return piping configuration may be used, but it may be difficult to achieve and
maintain proper water flow to the units.
An air vent must be installed in the water distribution system.•
The supply and return water piping should be run through the wall or floor penetration and terminate with a ball valve. •
The piping material used must comply with all local codes.
Refer to: • System Cleaning and Flushing procedures.
Pipe Locations
Figure 2
1=<A=:3
1/07<3B
1=<A=:3
16/AA7A
1=<23<A/B3
2@/7<:=1/B7=<
E/B3@1=<<31B7=<A
B/@53B/@3/4=@
E/::>3<3B@/B7=<
4CA323:31B@71/:
27A1=<<31B=>B7=</:
#Þf&Þ/@3//>>=F Þ
4@=;3253=416/AA7A
Þ4@=;4@=<B3253
=41/07<3B
#Þ
&Þ
B/@53B/@3/4=@
4:==@>3<3B@/B7=<
1/07<3B3FB3<2A
B=B67A>=7<B
#Þf&Þ/@3//>>=F Þ
4@=;3253=416/AA7A
!Þ4@=;4:==@
"D/113AA=@G
3:31B@71/:
8C<1B7=<0=F
14
ENVISION CONSOLE INSTALLATION MANUAL
Installation Steps (cont.)
Step 5: Provide Line Voltage Wiring
Check unit data plate located on control side of chassis for ampacity and fuse size.•
Remove electrical knockouts from chassis backplate.•
Run line voltage wiring through knockout and secure wiring to backplate or disconnect.•
Step 6: Chassis Installation
Level and secure backplate to wall.•
Position the chassis against back plate. Drive (2) screws through holes in lip of backplate into top flange of chassis.•
Step 7: Final Electrical Connection
Install flexible electrical conduit between the backplate or electrical disconnect and the unit mounted junction box. •
Make final wiring connections in disconnect and junction box, taking care to replace all covers when done. Wiring must •
conform to NEC and/or all local codes. Refer to Electrical Data.
NOTE: It is necessary to make final wiring connections prior to securing unit chassis to back plate on right-hand piping
models with electrical disconnect.
Step 8: Final Water Connection
For ease of installation and sound attenuation, high pressure (recommended) flexible hoses with a swivel fitting should •
be provided. Apply Teflon® tape or sealant compound to threaded hose fittings.
Combination shut-off/balancing valves should be installed on both the supply and return water lines of the unit.•
Flow control valves should be installed on the water discharge line.•
It is recommended that P/T ports be installed on the supply and return water lines.•
Step 9: Set Unit Controls
Locate the “continuous fan/cycle fan” switch within the electrical compartment of the chassis and set to desired position.•
(Remote wall thermostat units do not use this optional switch.)
Optional Control Settings-•
Remote Thermostat - Run low voltage wiring from unit to the desired thermostat location.
Mount and wire thermostat according to manufacturer’s recommendations.
Motorized Outside Air Damper - Locate the “damper on/damper off” damper switch within the electrical compartment
of the chassis and set to desired position.
Emergency Electrical Heat - Locate the “electric heat/normal/boilerless” control switch within the electrical compart-
ment of the chassis and set to desired position.
Step 10: Secure the Cabinet Cover
Position and lower cabinet over unit chassis. Apply pressure to the front of the cabinet to ensure that the back lip of the •
cabinet hooks over the tabs provided on the backplate.
Secure cabinet to chassis with mounting screws provided.•
Step 11: Perform Final Unit Check
Measure the pressure drop across the water coil and monitor water or air temperatures in both heating and cooling •
modes. The measured values should fall within the acceptable ranges shown in the Startup Performance table.
15
ENVISION CONSOLE INSTALLATION MANUAL
Installation Steps (cont.)
1
Top view
Side view
Figure 3
2
Field Converting Console
Chassis is normally configured with controls on right end and piping on left end (see Figure 3 top view). In this position
panel number 1 would be positioned against wall or back plate. Unit may also be turned 180° against wall or back plate. In
this position controls will be on left end and piping on right end panel number 2 would be positioned against wall or back
plate. Chassis must be enclosed with an approved cabinet enclosure.
Remove 4 screws from front kick panel on cabinet.1.
Remove cabinet from chassis by lifting and sliding cabinet 2.
straight up.
Remove grille assembly from cabinet by removing 4 screws from 3.
brackets located on the bottom of the grille and door assemblies.
Replace grille/door assemblies into cabinet repositioning pieces 4.
1, 2, and 3 into the locations directly opposite the original positions.
Secure by replacing mounting brackets. (Note: Be sure that louvers
on the grille assembly are facing the proper direction when
replacing the grille section.)
Replace grille/frame assembly into cabinet, and secure by replacing 5.
mounting brackets.
Replace cabinet by sliding it down over the top of the chassis.6.
Remove tab on leg that extends into return air opening. When the 7.
grille side of the cabinet is flat against chassis there will be 4
holes that line up in the leg section. Only use 1 hole for alignment
for opposite side of grille. (Note: The tab can be removed by
twisting back and forth until it breaks off.)
Remove plastic strip from tab and replace on rough edge that the 8.
tab was removed from.
Replace screws in font kick panel to secure cabinet to chassis.9.
Mount filter bracket in designated opening area. (Note: The filter 10.
bracket will only fit in one direction if cabinet is installed properly.)
Figure 4
4
2
1
3
5
Depends on Cabinet Size
16
ENVISION CONSOLE INSTALLATION MANUAL
System Cleaning and Flushing
Cleaning and Flushing
Prior to start up of any heat pump, the water circulating system must be
cleaned and flushed of all dirt and debris.
If the system is equipped with water shutoff valves, the supply and
return runouts must be connected together at each unit location (This
will prevent the introduction of dirt into the unit, see Figure 7). The
system should be filled at the water make-up connection with all air
vents open. After filling, vents should be closed.
The contractor should start the main circulator with the pressure reduc-
ing valve makeup open. Vents should be checked in sequence to bleed
off any trapped air and to verify circulation through all components of
the system.
As water circulates through the system, the contractor should check
and repair any leaks found in the piping system. Drain(s) at the lowest
point(s) in the system should be opened for initial flush and blowdown, making sure water fill valves are set at the same
rate. Check the pressure gauge at the pump suction and manually adjust the make-up water valve to hold the same posi-
tive pressure both before and after opening the drain valves. Flushing should continue for at least two hours, or longer if
required, until drain water is clean and clear.
The supplemental heater and/or circulator pump, if used, should be shut off. All drains and vents should be opened to
completely drain the system. Short-circuited supply and return runouts should now be connected to the unit supply and
return connections.
Refill the system with clean water. Test the system water for acidity and treat as required to leave the water slightly alkaline
(pH 7.5 to 8.5). The specified percentage of antifreeze may also be added at this time. Use commercial grade antifreeze
designed for HVAC systems only. Environol™ brand antifreeze is recommended..
Once the system has been filled with clean water and antifreeze (if used), precautions should be taken to protect the sys-
tem from dirty water conditions. Dirty water will result in system-wide degradation of performance, and solids may clog
valves, strainers, flow regulators, etc. Additionally, the heat exchanger may become clogged which reduces compressor
service life and can cause premature unit failure.
In boiler/tower application, set the loop control panel set points to desired temperatures. Supply power to all motors and
start the circulating pumps. After full flow has been established through all components including the heat rejector (re-
gardless of season), air vented and loop temperatures stabilized, each of the units will be ready for check, test and start up
and for air and water balancing.
Ground Source Loop System Checkout
Once piping is completed between the unit pumping system and ground loop, final purging and charging of the loop is
needed. A high pressure pump is needed to achieve adequate flow velocity in the loop to purge air and dirt particles from
the loop itself. Antifreeze solution is used in most areas to prevent freezing. Flush the system adequately to remove as
much air as possible; then pressurize the loop to a static pressure of 40-50 PSI (summer) or 50-75 PSI (winter). This is
normally adequate for good system operation. Loop static pressure may decrease soon after initial installation, due to pipe
expansion and loop temperature change. Running the unit for at least 30 minutes after the system has been completely
purged of air will allow for the “break-in” period. It may be necessary to adjust static loop pressure (by adding water) after
the unit has run for the first time. Loop static pressure will also fluctuate with the seasons. Pressures will be higher in the
winter months than during the cooling season. This fluctuation is normal and should be considered when charging the
system initially.
Insure the pump provides adequate flow through the unit by checking pressure drop across the heat exchanger.
Usually 2.25-3.0 GPM of flow per ton of cooling capacity is recommended in earth loop applications.
Return Runout
Supply Runout
Mains
Rubber Hose
Runouts Initially
Connected Together
Figure 7: Flushing with Water
Shutoff Valve Equipped Systems
17
ENVISION CONSOLE INSTALLATION MANUAL
Open Loop Ground Water Systems
Always maintain water pressure in the heat exchanger by placing water control valves at the outlet of the unit to prevent
mineral precipitation. Use a closed, bladder-type expansion tank to minimize mineral formation due to air exposure. Insure
proper water flow through the unit by checking pressure drop across the heat exchanger and comparing it to the figures in
unit capacity data tables in the specification catalog. 1.5-2 GPM of flow per ton of cooling capacity is recommended in open
loop applications.
Discharge water from the unit is not contaminated in any manner and can be disposed of in various ways, depending on
local codes, i.e. recharge well, storm sewer, drain field, adjacent stream or pond, etc. Most local codes forbid the use of
sanitary sewer for disposal. Consult your local building and zoning departments to assure compliance in your area.
Note: For open loop/groundwater systems or systems that do not contain an antifreeze solution, set SW1-Switch #2 to the
“WELL” position
(Refer to the Dip Switch Field Selection table). Slow opening/closing solenoid valves (type VM) are recom-
mended to eliminate water hammer.
Water Quality
In ground water situations where scaling could be heavy or where biological growth such as iron bacteria will be present,
a closed loop system is recommended. The heat exchanger coils in ground water systems may, over a period of time, lose
heat exchange capabilities due to a buildup of mineral deposits inside. These can be cleaned, but only by a qualified service
mechanic, as special solutions and pumping equipment are required. Desuperheater coils can likewise become scaled and
possibly plugged. In areas with extremely hard water, the owner should be informed that the heat exchanger may require
occasional flushing.
Units with cupronickel heat exchangers are recommended for open loop applications due to the increased resistance to
build-up and corrosion, along with reduced wear caused by acid cleaning.
18
ENVISION CONSOLE INSTALLATION MANUAL
Electrical Connections
General
Be sure the available power is the same voltage and phase as that shown on the unit serial plate. Line and low voltage wir-
ing must be done in accordance with local codes or the National Electric Code, whichever is applicable.
208 Volt Operation
All Envision Series 208/230 units are factory wired for 230 volt operation. For 208 volt operation, the red and blue trans-
former wires must be switched.
Microprocessor Remote Thermostat Wiring
Auxiliary Heat Ratings
TB
O
G
Y
C
R
L
S
X2
X1
W2
Field
Connections
Unit
Connections
24 VAC
COMMON
COMPRESSOR
REVERSING
VALVE
FAN
LOCKOUT
SIGNAL
SHUTDOWN
NIGHT
SETBACK
LOAD SHED
Requires common
connections or 24
VAC for activation
Red
Black
Yellow
Orange
Green
Brown
Blue
Violet
Pink
Figure 5
Model
Rated
Voltage
Voltage
Min./Max.
Heater
Element
Watts
Fan
Motor
FLA
Heater
Element
FLA
Total
Unit
FLA
Min.
Circuit
Amp.
Max.
Fuse/
Brkr.
09-12
208/60/1 197/254 2000 0.50 9.62 10.1 12.7 15
230/60/1 197/254 2445 0.50 10.63 11.1 13.9 15
265/60/1 239/292 2000 0.55 7.55 8.1 10.1 15
15-18
208/60/1 197/254 3000 0.69 14.42 15.1 18.9 20
230/60/1 197/254 3668 0.69 15.95 16.6 20.8 25
265/60/1 239/292 3000 0.65 11.32 12.0 15.0 15
3/4/08
Always refer to unit name plate data prior to installation.
19
ENVISION CONSOLE INSTALLATION MANUAL
Fan Performance Data
Model
CFM
Low Speed High Speed
09 300 350
12 300 350
15 450 500
18 450 500
Factory settings are in Bold
Air ow values are with dry coil and standard lter.
For wet coil performance rst calculate the face velocity of the air coil
(Face Velocity [fpm] = Airow [cfm] / Face Area [sq ft]). Then for
velocities of 200 fpm reduce the static capability by 0.03 in. wg, 300
fpm by 0.08 in. wg, 400 fpm by 0.12in. wg. and 500 fpm by 0.16 in. wg.
Unit Electrical Data
Model
Rated
Voltage
Voltage
Min/Max
Compressor
Fan
Motor
FLA
Total
Unit
FLA
Min
Circ
Amp
Max
Fuse/
HACR
MCC RLA LRA
09
208-230/60/1 197/253 6.4 4.1 21.0 0.50 4.6 5.6 10
265/60/1* 238/292 na 4.3 22.0 0.50 4.8 5.9 10
12
208-230/60/1 197/253 7.7 4.9 25.0 0.50 5.4 6.7 10
265/60/1* 238/292 na 5.3 22.0 0.50 5.8 7.1 10
15
208-230/60/1 197/253 9.2 5.9 29.0 0.69 6.6 8.1 10
265/60/1* 238/292 na 5.6 28.0 0.65 6.3 7.7 10
18
208-230/60/1 197/253 10.4 6.7 33.5 0.69 7.3 9.0 15
265/60/1* 238/292 na 7.3 28.0 0.65 8.0 9.8 15
HACR circuit breaker in USA only
* RLA determine per UL1995 test procedure and not from compressor rating.
4/8/08
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Envision R-410A Residential User manual
- Category
- Heat pumps
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Envision NCW09-18 Installation guide
-
-
-
-
Envision Peripherals NAH022A*1R User manual
-
Envision NSKW 06 Installation guide
-
-
-
Envision Peripherals R-410A Residential User manual
-
Other documents
-
Unbranded Compressor Lockout Board Accessory Kit Installation guide
-
Reznor R6GN Installation guide
-
Global Industrial 246116 Quick Manual
-
Crown Boiler Oil Furnace Shorty Ecm Motor User manual
-
Wakeman Outdoors W470050 Operating instructions
-
Trane Trane Communicating Thermostats (BACnet) User manual
-
VERSATEC V120W Installation guide
-
STA-RITE Intelliboost R Series Quick start guide
-
Johnson Controls RC Series Engineering Manual
-
Greenheck FX10 Controller User manual
