Lexmark CX725 Series User manual
- Category
- Laser/LED printers
- Type
- User manual
Product information
Product name:
Lexmark(TM) CX725de, CX725dhe, CX725dthe
Machine type:
7528
Model(s):
576, 578
Edition notice
January 25, 2016
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK
INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement
may not apply to you.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available
in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that
product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any
existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products,
programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
Trademarks
Lexmark and the Lexmark logo are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer
commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language.
This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions
corresponding to the commands.
PostScript is a registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
All other trademarks are the property of their respective owners.
© 2016 Lexmark International, Inc.
All rights reserved.
P/N 12G3423
7528
Table of contents
Product information......................................................................................2
Edition notice.................................................................................................2
Notices and safety information................................................................. 13
Laser notice..........................................................................................................................................................13
Avis relatif à l'utilisation du laser.................................................................................................................... 13
Notificació del làser........................................................................................................................................... 13
Aviso de láser......................................................................................................................................................13
Aviso sobre laser................................................................................................................................................14
Avvertenze sui prodotti laser.......................................................................................................................... 14
Laserinformatie................................................................................................................................................... 14
Lasererklæring.................................................................................................................................................... 14
Laser-Hinweis......................................................................................................................................................15
Laserilmoitus........................................................................................................................................................15
Lasermerknad......................................................................................................................................................15
Meddelande om laser....................................................................................................................................... 15
レーザーについて...................................................................................................................... 16
레이저 고지사항....................................................................................................................... 16
激光注意事项............................................................................................................................16
雷射聲明................................................................................................................................... 16
Safety information.............................................................................................................................................. 16
Consignes de sécurité...................................................................................................................................... 17
Informació de seguretat....................................................................................................................................17
Información de seguridad................................................................................................................................18
Informações sobre segurança........................................................................................................................ 18
Informatie over veiligheid.................................................................................................................................18
Informazioni sulla sicurezza.............................................................................................................................19
Säkerhetsinformation........................................................................................................................................19
Sicherheitshinweise..........................................................................................................................................20
Sikkerhedsoplysninger....................................................................................................................................20
Sikkerhetsinformasjon..................................................................................................................................... 20
Turvallisuusohjeet...............................................................................................................................................21
안전 정보.................................................................................................................................. 21
7528
Table of contents
3
安全信息................................................................................................................................... 21
安全情報................................................................................................................................... 22
安全資訊................................................................................................................................... 22
Preface......................................................................................................... 23
Conventions........................................................................................................................................................23
General caution statements........................................................................................................................... 23
General information................................................................................... 25
Finding the serial number...............................................................................................................................25
Paper and specialty media guide................................................................................................................. 26
Paper guidelines..........................................................................................................................................................26
Using specialty media................................................................................................................................................ 27
Supported paper sizes, types, and weights......................................................................................................... 29
Data security notice...........................................................................................................................................31
Tools required for service................................................................................................................................32
Diagnostic information.............................................................................. 35
Troubleshooting overview.............................................................................................................................. 35
Performing the initial troubleshooting check....................................................................................................... 35
Power‑on reset (POR) sequence............................................................................................................................. 35
Fixing print quality issues................................................................................................................................36
Initial print quality check............................................................................................................................................ 36
Toner easily rubs o check....................................................................................................................................... 36
Background or gray background check................................................................................................................ 38
Blank or white pages check ..................................................................................................................................... 39
Gapping or half color page check ........................................................................................................................... 41
Blurred print or color misalignment check ........................................................................................................... 42
Horizontal colored lines or banding check .......................................................................................................... 43
Text or images cut o check .................................................................................................................................... 45
Mottled print and dots check ................................................................................................................................... 45
Vertical white lines check.......................................................................................................................................... 46
Ghost images check................................................................................................................................................... 48
Solid color or black image check............................................................................................................................ 49
Vertical colored lines or banding check................................................................................................................50
Image void scan direction check ............................................................................................................................. 51
Image void process direction check ...................................................................................................................... 53
Dark print check........................................................................................................................................................... 54
Missing color check ....................................................................................................................................................55
Uneven print density check......................................................................................................................................56
Repeating defects check........................................................................................................................................... 57
Random marks check................................................................................................................................................. 59
7528
Table of contents
4
Light print check ..........................................................................................................................................................59
Skewed print service check ..................................................................................................................................... 62
Fixing scan quality issues................................................................................................................................64
Dark image quality (using the ADF or scanner) check ...................................................................................... 64
Vertical lines (process direction using the ADF) check.....................................................................................65
Spots (using the flatbed scanner) check...............................................................................................................66
ADF skew check.......................................................................................................................................................... 67
Media damage (using the ADF) check................................................................................................................... 69
Paper jams...........................................................................................................................................................70
Avoiding jams............................................................................................................................................................... 70
Identifying jam locations..............................................................................................................................................71
Paper jam in trays........................................................................................................................................................ 72
Paper jam behind door E............................................................................................................................................73
Paper jam in the multipurpose feeder ....................................................................................................................73
Paper jam in the standard bin...................................................................................................................................74
Paper jam in door A .................................................................................................................................................... 75
200 paper jams............................................................................................................................................................ 78
201 paper jams............................................................................................................................................................. 84
202 paper jams............................................................................................................................................................ 85
203 paper jams............................................................................................................................................................ 93
211 paper jams.............................................................................................................................................................. 94
221 paper jams............................................................................................................................................................. 95
230 paper jams............................................................................................................................................................ 96
231 paper jams............................................................................................................................................................102
232 paper jams...........................................................................................................................................................108
240 paper jams............................................................................................................................................................113
241 paper jams............................................................................................................................................................125
242–244 paper jams.................................................................................................................................................133
28y and 680 paper jams ..........................................................................................................................................158
User attendance messages.......................................................................................................................... 163
31 user attendance error messages......................................................................................................................163
32 user attendance error messages.....................................................................................................................164
33 user attendance error messages.....................................................................................................................165
42 user attendance error messages.....................................................................................................................165
43 user attendance error messages .....................................................................................................................166
80 user attendance error messages.....................................................................................................................166
82 user attendance error messages.....................................................................................................................167
83 user attendance error messages.....................................................................................................................167
84 user attendance error messages.....................................................................................................................168
85 user attendance error messages.....................................................................................................................169
88 user attendance error messages.....................................................................................................................170
Non‑supply user attendance error messages ....................................................................................................170
Missing toner, developer, or photoconductor service check........................................................................... 171
Waste toner bottle service check...........................................................................................................................173
7528
Table of contents
5
Region mismatch service check.............................................................................................................................173
Maintenance kit service check ...............................................................................................................................174
Cartridge or photoconductor error service check.............................................................................................174
Mismatched paper size service check .................................................................................................................175
Insucient memory service check ........................................................................................................................176
Complex page service check..................................................................................................................................176
Flash memory failure service check...................................................................................................................... 177
Insucient flash memory service check .............................................................................................................. 177
Unsupported internal option service check........................................................................................................178
Disabled port service check....................................................................................................................................178
Excess options service check .................................................................................................................................179
Incompatible hardware option service check.....................................................................................................180
Hard disk failure service check ..............................................................................................................................180
Printer hardware errors................................................................................................................................... 181
1yy errors........................................................................................................................................................................181
6yy errors......................................................................................................................................................................216
9yy errors.....................................................................................................................................................................222
ADF/scanner hardware errors.....................................................................................................................238
8yy error messages ..................................................................................................................................................238
Scanner disabled error service check .................................................................................................................238
Scanner communication failure service check..................................................................................................239
Scanner configuration error service check ........................................................................................................240
Scan/fax/copy symptoms ........................................................................................................................................240
Black or blank page copy service check .............................................................................................................241
Flatbed motor service check..................................................................................................................................242
Flatbed home position service check..................................................................................................................242
ADF rattling noise service check ..........................................................................................................................243
Flatbed legal‑size scan service check.................................................................................................................244
ADF feed errors service check..............................................................................................................................245
ADF duplex service check ......................................................................................................................................247
Modem/fax card service check..............................................................................................................................248
Blank spaces on incoming fax service check....................................................................................................249
Stretched words on incoming fax service check..............................................................................................249
Fax reception service check ..................................................................................................................................249
Fax transmission service check..............................................................................................................................251
Fax error log codes...................................................................................................................................................254
Escalating a fax issue to second‑level support .................................................................................................257
Symptoms.........................................................................................................................................................259
Base printer symptoms............................................................................................................................................259
Control panel service check...................................................................................................................................259
Interlock switch service check.............................................................................................................................. 260
Sensor (narrow media) and sensor (fuser buckle) service check.................................................................262
Dead machine service check.................................................................................................................................262
Mobile solutions module NFC service check ....................................................................................................264
7528
Table of contents
6
Network service check ............................................................................................................................................265
Toner meter cycle (TMC) card service check.....................................................................................................268
USB service check ....................................................................................................................................................269
Control panel USB cable service check..............................................................................................................269
Toner patch sensing service check ......................................................................................................................270
Auto alignment service check................................................................................................................................272
Service menus...........................................................................................277
Understanding the printer control panel...................................................................................................277
Using the control panel ........................................................................................................................................... 277
Understanding the status of the power button and indicator light..............................................................278
Using the home screen............................................................................................................................................278
Menus list.....................................................................................................................................................................279
Diagnostics menu...........................................................................................................................................280
Entering the Diagnostics menu ............................................................................................................................ 280
Event Log......................................................................................................................................................................281
Reports ..........................................................................................................................................................................281
Advanced Print Quality Samples...........................................................................................................................282
Input tray quick print.................................................................................................................................................282
Printer Setup...............................................................................................................................................................282
Printer diagnostics and adjustments....................................................................................................................284
Scanner Diagnostics.................................................................................................................................................286
Additional input tray diagnostics.......................................................................................................................... 290
Service Engineer menu..................................................................................................................................291
Entering Invalid engine mode.................................................................................................................................291
Entering the Service Engineer (SE) menu............................................................................................................291
General SE ...................................................................................................................................................................291
Network SE ..................................................................................................................................................................291
Fax SE...........................................................................................................................................................................292
Scan SE ........................................................................................................................................................................293
Repair information................................................................................... 295
Removal precautions..................................................................................................................................... 295
Data security notice..................................................................................................................................................295
Handling ESD‑sensitive parts.................................................................................................................................296
Controller board/control panel replacement .....................................................................................................296
Restoring the printer configuration after replacing the controller board ...................................................297
Restoring solutions, licenses, and configuration settings ............................................................................. 300
Updating the printer firmware ................................................................................................................................301
Backing up eSF solutions and settings ...............................................................................................................302
Disconnecting ribbon cables..................................................................................................................................302
Adjustments......................................................................................................................................................303
Printhead alignment adjustment ...........................................................................................................................303
7528
Table of contents
7
Registration adjustment...........................................................................................................................................305
Scanner Manual Registration .................................................................................................................................307
ADF registration adjustment...................................................................................................................................307
Flatbed registration adjustment ............................................................................................................................308
Removal procedures......................................................................................................................................308
Cover removals............................................................................................................................................... 309
Front cover removal..................................................................................................................................................309
Top cover removal.......................................................................................................................................................311
Left cover removal .....................................................................................................................................................316
Right cover removal...................................................................................................................................................318
Motor cover removal .................................................................................................................................................319
Toner door removal...................................................................................................................................................322
Toner door mount bracket removal......................................................................................................................324
Toner door mount frame removal .........................................................................................................................326
Output bin cover removal .......................................................................................................................................330
Top frame cover removal..........................................................................................................................................331
Top frame base cover removal ..............................................................................................................................333
Scanner rear right cover removal .........................................................................................................................334
Scanner rear left cover removal ............................................................................................................................335
External air filter removal.........................................................................................................................................336
Control panel removals................................................................................................................................. 336
Lower control panel bezel removal......................................................................................................................336
Control panel bezel removal.................................................................................................................................. 337
Control panel removal.............................................................................................................................................. 337
Control panel tub removal ......................................................................................................................................338
Control panel tub mounting bracket removal....................................................................................................339
Control panel arms removal ...................................................................................................................................340
Duplex removals..............................................................................................................................................343
Duplex inner guide removal ...................................................................................................................................343
Duplex outer guide removal...................................................................................................................................344
Pivot shaft removal....................................................................................................................................................345
Tensioner belt removal ............................................................................................................................................346
Sensor (duplex) removal.......................................................................................................................................... 347
Sensors (fuser buckle and narrow media) removal..........................................................................................348
Left removals....................................................................................................................................................350
Motor (EP drive) removal .........................................................................................................................................350
Power cable removal.................................................................................................................................................351
Motor (output) removal..............................................................................................................................................351
Motor (deskew) removal..........................................................................................................................................353
Fuser fan removal......................................................................................................................................................353
Main fan removal.......................................................................................................................................................355
EP gear box removal ................................................................................................................................................356
LVPS removal..............................................................................................................................................................359
LVPS cage removal...................................................................................................................................................362
7528
Table of contents
8
Motor (black only retract) removal........................................................................................................................363
Right removals.................................................................................................................................................365
Sensor (weather station) removal ........................................................................................................................365
Sensor (paper size) removal...................................................................................................................................366
Sensor (waste toner contact) removal ................................................................................................................368
TMC card removal.....................................................................................................................................................369
Motor (duplex/MPF) removal ..................................................................................................................................369
Motor (fuser) removal ...............................................................................................................................................372
HVPS removal ............................................................................................................................................................ 373
Sensor (MPF paper present) removal ..................................................................................................................376
Waste toner bottle idler gear removal .................................................................................................................378
Imaging unit cover removal ....................................................................................................................................378
Sensor (TPS) removal ...............................................................................................................................................379
TPS sled removal........................................................................................................................................................381
Toner cartridge contacts removal .........................................................................................................................382
TPS wiper mechanism removal .............................................................................................................................384
TPS wiper removal....................................................................................................................................................386
Front removals.................................................................................................................................................387
Fuser removal............................................................................................................................................................. 387
Transfer module removal.........................................................................................................................................388
Transfer module guide rail removal......................................................................................................................390
Sensor (media type) removal..................................................................................................................................394
Sensor (input) removal .............................................................................................................................................395
Deskew rollers removal...........................................................................................................................................396
Diverter removal........................................................................................................................................................404
Redrive guide removal.............................................................................................................................................406
Sensor (redrive) removal .........................................................................................................................................406
Rear removals..................................................................................................................................................408
Controller board shield removal............................................................................................................................408
Inner controller board shield removal..................................................................................................................409
Controller board removal........................................................................................................................................409
TPS cables removal ...................................................................................................................................................411
Modem removal...........................................................................................................................................................411
Hard disk drive removal............................................................................................................................................412
Secure element SIM card removal.........................................................................................................................412
Top removals.....................................................................................................................................................413
Printhead removal......................................................................................................................................................413
Developer hold down removal ...............................................................................................................................415
Output roll removal ....................................................................................................................................................416
Output bin exit cover removal ................................................................................................................................418
Output bin flag removal............................................................................................................................................419
Bottom removals.............................................................................................................................................420
Front cover hinges removal....................................................................................................................................420
Tray rail removal..........................................................................................................................................................421
7528
Table of contents
9
Media feeder removal..............................................................................................................................................422
Isolation unit removal ...............................................................................................................................................423
Aligner idler gears removal ....................................................................................................................................425
ADF and flatbed removals............................................................................................................................426
ADF removal...............................................................................................................................................................426
Facade removal .........................................................................................................................................................430
Speaker removal ........................................................................................................................................................431
ADF top cover removal.............................................................................................................................................431
ADF left hinge removal ............................................................................................................................................432
ADF right hinge removal .........................................................................................................................................433
Scanner front cover removal..................................................................................................................................434
Left flatbed cover removal......................................................................................................................................435
Flatbed removal.........................................................................................................................................................435
Scanner cable cover removal .................................................................................................................................441
Scanner tilt removal...................................................................................................................................................441
550-sheet tray removals............................................................................................................................... 444
550-sheet tray right cover removal......................................................................................................................444
Motor (550-sheet tray pass‑through) removal...................................................................................................445
550‑sheet tray paper feeder removal ................................................................................................................. 447
Sensor (550-sheet tray pass-through) removal.................................................................................................448
Sensor (550-sheet tray trailing edge) removal..................................................................................................449
Sensor (550-sheet tray paper size) removal......................................................................................................449
550-sheet tray controller board assembly removal..........................................................................................451
550-sheet tray interface cable removal..............................................................................................................452
550-sheet tray empty sensor actuator removal................................................................................................453
Sensor (550-sheet tray empty) removal..............................................................................................................454
Sensor (550-sheet tray index) removal ...............................................................................................................455
Component locations...............................................................................457
Printer configurations.....................................................................................................................................457
Controller board connectors........................................................................................................................458
LVPS controller board connectors..............................................................................................................473
Motor locations................................................................................................................................................475
Sensor locations..............................................................................................................................................476
Maintenance..............................................................................................479
Inspection guide..............................................................................................................................................479
Scheduled maintenance...............................................................................................................................480
Maintenance kits........................................................................................................................................................480
Identifying the type of fuser used in the printer.................................................................................................481
Cleaning the printer....................................................................................................................................... 482
Cleaning the printer..................................................................................................................................................482
7528
Table of contents
10
Cleaning the scanner glass ....................................................................................................................................482
Cleaning the printhead lenses...............................................................................................................................483
Cleaning the main tray duplex turnaround.........................................................................................................484
Parts catalog............................................................................................. 486
Legend...............................................................................................................................................................486
Assembly 1: Covers 1...................................................................................................................................... 487
Assembly 2: Covers 2....................................................................................................................................489
Assembly 3: Control panel............................................................................................................................ 491
Assembly 4: ADF and flatbed...................................................................................................................... 493
Assembly 5: Fuser.......................................................................................................................................... 495
Assembly 6: Transfer module...................................................................................................................... 497
Assembly 7: Paper feed................................................................................................................................ 499
Assembly 8: Paper path 1.............................................................................................................................. 501
Assembly 9: Paper path 2............................................................................................................................ 503
Assembly 10: Duplex......................................................................................................................................505
Assembly 11: Electrical................................................................................................................................... 507
Assembly 12: 550‑sheet tray option 1..........................................................................................................511
Assembly 13: 550‑sheet tray option 2........................................................................................................513
Assembly 14: Adjustable stand.....................................................................................................................515
Assembly 15: Miscellaneous parts...............................................................................................................517
Assembly 16: Power cords.............................................................................................................................519
Appendix A: Printer
specifications
......................................................... 521
Power consumption........................................................................................................................................ 521
Product power consumption...................................................................................................................................521
Sleep Mode..................................................................................................................................................................521
Hibernate Mode..........................................................................................................................................................521
O mode......................................................................................................................................................................522
Total energy usage ...................................................................................................................................................522
Selecting a location for the printer.............................................................................................................522
Noise emission levels....................................................................................................................................523
Temperature information.............................................................................................................................. 523
Appendix B: Options and features.........................................................525
Available internal options.............................................................................................................................525
Installing optional trays................................................................................................................................. 525
Adding available options in the print driver.............................................................................................526
7528
Table of contents
11
Appendix C: Theory of operation...........................................................529
Paper path and transport components.....................................................................................................529
Tray section.................................................................................................................................................................529
MPF section ................................................................................................................................................................530
Isolation unit section..................................................................................................................................................531
Aligner section ...........................................................................................................................................................532
Fuser section ..............................................................................................................................................................534
Duplex section ...........................................................................................................................................................535
Print engine theory......................................................................................................................................... 537
Electrophotographic process.................................................................................................................................537
EP process basics .....................................................................................................................................................537
ADF theory........................................................................................................................................................544
ADF paper path..........................................................................................................................................................545
ADF paper path sensors..........................................................................................................................................546
ADF tray pick and feed ............................................................................................................................................546
ADF separation ..........................................................................................................................................................547
ADF registration.........................................................................................................................................................548
ADF scan and exit .....................................................................................................................................................549
ADF duplex ................................................................................................................................................................ 550
Color theory...................................................................................................................................................... 551
Color theory .................................................................................................................................................................551
Appendix D: Acronyms............................................................................555
Acronyms..........................................................................................................................................................555
Index...........................................................................................................557
Part number index....................................................................................563
Part name index....................................................................................... 569
7528
Table of contents
12
Notices and safety information
Laser notice
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for
Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements
of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) AlGaInP
laser that is nominally 15-milliwatts operating in the wavelength region of 650–670 nanometers and enclosed
in a non-serviceable printhead assembly. The laser system and printer are designed so there is never any human
access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service
conditions.
Avis relatif à l'utilisation du laser
Cette imprimante est
certifiée
conforme aux exigences de la réglementation des Etats-Unis relative aux produits
laser de classe I (1) (DHHS 21 CFR, Chapitre I, Sous-chapitre J). Pour les autres pays, elle est
certifiée
conforme
aux exigences des normes CEI 60825-1 relatives aux produits laser de classe I.
Les produits laser de Classe I ne sont pas considérés comme dangereux. L'imprimante contient un dispositif
laser AlGaInP (aluminium, gallium, indium et phosphore) de classe IIIb (3b) d'une puissance nominale de
15 milliwatts fonctionnant dans la plage de longueurs d'onde allant de 650 à 670 nanomètres et scellé dans
un compartiment de têtes d'impression non réparable. Le système laser ainsi que l'imprimante ont été conçus
de manière à ce que personne ne soit jamais exposé à des radiations laser dépassant le niveau de classe I
dans le cadre d'un fonctionnement normal, de l'entretien par l'utilisateur ou de la maintenance.
Notificació del làser
La impressora està
certificada
als EUA per complir els requeriments de DHHS 21 CFR, capítol I, subcapítol J
per a productes de làser Classe I (1), i a la resta del món s’ha
certificat
com productes de làser Classe I segons
els requeriments de la norma IEC 60825-1.
Els productes de làser Classe I no es consideren perillosos. La impressora conté un làser intern Classe IIIb (3b)
AlGaInP que normalment és de 15 miliwatts, que funciona a la regió de longitud d’ona de 650 a 670 nanòmetres
i es troba dins d’una unitat de capçals d’impressió no substituïble. El sistema làser i la impressora estan
dissenyats de manera que les persones no estiguin exposades a una radiació del làser superior al nivell de
Classe I durant el funcionament normal, el manteniment de l’usuari o les condicions de servei prescrites.
Aviso de láser
Esta impresora se ha certificado en EE.UU. cumpliendo con los requisitos de DHHS 21 CFR, capítulo I,
subcapítulo J para los productos láser de Clase I (1) y en otros países está certificada como un producto láser
de Clase I de acuerdo con los requisitos de IEC 60825-1.
Los productos láser de Clase I no se consideran peligrosos. Este producto contiene un láser interno de Clase
IIIb (3b) AlGaInP que opera nominalmente a 20 milivatios en una longitud de onda de 650–670 nanómetros
cerrado en un conjunto de cabezal de impresión que no se puede reparar. El sistema láser y la impresora se
7528
Notices and safety information
13
han diseñado para que el ser humano no acceda nunca a las radiaciones láser por encima del nivel de Clase
I durante su uso normal, ni en tareas de mantenimiento o intervenciones de servicio técnico prescritas.
Aviso sobre laser
Esta impressora foi
certificada
nos EUA por estar em conformidade com os requisitos do DHHS 21 CFR capítulo
I, subcapítulo J, para produtos a laser de Classe I (1) e, nos demais países, foi
certificada
como um produto a
laser de Classe I em conformidade com os requisitos da IEC 60825-1.
Os produtos a laser de Classe I não são considerados prejudiciais. A impressora contém, internamente, um
laser de Classe IIIb (3b) AlGaInP que funciona nominalmente a 15 miliwatts no comprimento de onda de 650-670
nanômetros, incluso em um conjunto do cabeçote de impressão sem possibilidade de manutenção. O sistema
do laser e a impressora foram projetados para que jamais haja acesso humano à radiação do laser acima do
nível da Classe I durante a operação normal ou a manutenção pelo usuário ou sob as condições de manutenção
prescritas.
Avvertenze sui prodotti laser
La stampante è
certificata
negli Stati Uniti come prodotto conforme ai requisiti DHHS 21 CFR Capitolo I,
Sottocapitolo J per i prodotti laser di Classe I (1), mentre in altri paesi è certificata come prodotto laser di Classe
I conforme ai requisiti IEC 60825-1.
I prodotti laser di Classe I non sono considerati pericolosi. La stampante contiene internamente un laser AlGaInP
di Classe IIIb (3b) con valore nominale di 15 milliwatt, funzionante nella regione della lunghezza d'onda dei
650-670 nanometri e contenuto in un gruppo testina di stampa non riparabile. Il sistema laser e la stampante
sono stati progettati in modo da impedire l'esposizione a radiazioni laser superiori al livello previsto dalla Classe
I durante le normali operazioni di stampa, manutenzione o assistenza.
Laserinformatie
De printer is in de Verenigde Staten gecertificeerd als een product dat voldoet aan de vereisten van DHHS 21
CFR hoofdstuk 1, paragraaf J voor laserproducten van klasse I (1). Elders is de printer gecertificeerd als een
laserproduct van klasse I dat voldoet aan de vereisten van IEC 60825-1.
Laserproducten van klasse I worden geacht geen gevaar op te leveren. De printer bevat intern een laser van
klasse IIIb (3b) AlGaInP met een nominaal vermogen van 15 milliwatt in een golflengtebereik van 650-670
nanometer in een niet-bruikbare printkopeenheid. Het lasersysteem en de printer zijn zodanig ontworpen dat
gebruikers nooit blootstaan aan laserstraling die hoger is dan het toegestane niveau voor klasse I-apparaten,
tijdens normaal gebruik, onderhoudswerkzaamheden door de gebruiker of voorgeschreven
servicewerkzaamheden.
Lasererklæring
Printeren er certificeret i USA i henhold til kravene i DHHS 21 CFR kapitel I, underafsnit J for klasse l (1)
laserprodukter og er andre steder certificeret som et klasse I-laserprodukt i henhold til kravene i IEC 60825-1.
Klasse I-laserprodukter er ikke anset som farlige. Printeren indeholder internt en Klasse IIIb (3b) AlGaAs-laser,
der nominelt er en 15 milliwatt laser, som fungerer i bølgelængdeområdet 650–670 nanometer og indbygget
i en printhovedenhed, der ikke er servicerbar. Lasersystemet og printeren er designet på en sådan måde, at
7528
Notices and safety information
14
der ikke er en direkte laserstråling, der overskrider Klasse I-niveauet under normal brug, brugers
vedligeholdelse eller de foreskrevne servicebetingelser.
Laser-Hinweis
Der Drucker wurde in den USA
zertifiziert
und entspricht den Anforderungen der Vorschriften DHHS 21 CFR
Kapitel I für Laserprodukte der Klasse I (1), andernorts ist er als Laserprodukt der Klasse I
zertifiziert,
das den
Anforderungen von IEC 60825-1 entspricht.
Laserprodukte der Klasse I werden nicht als gefährlich betrachtet. Der Drucker enthält im Inneren einen Laser
der Klasse IIIb (3b) AlGaInP mit 15 Milliwatt, im Wellenlängenbereich von 650 bis 670 Nanometern arbeitet.
Dieser
befindet
sich in einer Druckkopfeinheit, die nicht gewartet werden kann. Das Lasersystem und der
Drucker sind so konstruiert, dass unter normalen Betriebsbedingungen, bei der Wartung durch den Benutzer
oder bei den vorgeschriebenen Wartungsbedingungen Menschen keiner Laserstrahlung ausgesetzt sind, die
die Werte für Klasse I überschreitet.
Laserilmoitus
Tämä tulostin on
sertifioitu
Yhdysvalloissa DHHS 21 CFR, Chapter I, Subchapter J -standardin mukaiseksi luokan
I (1) -lasertuotteeksi ja muualla IEC 60825-1 -standardin mukaiseksi luokan I lasertuotteeksi.
Luokan I lasertuotteita ei pidetä haitallisina. Tulostimen sisällä on luokan IIIb (3b) AlGaInP -laser, jonka
nimellisteho on 15 mW milliwatts, joka toimii 650–670 nanometrin aallonpituuksilla ja joka on suljettu
tulostuspäähän, jota käyttäjä ei voi huoltaa. Laserjärjestelmä ja tulostin ovat rakenteeltaan sellaisia, että käyttäjä
ei joudu alttiiksi luokkaa 1 suuremmalle säteilylle normaalin käytön, ylläpidon tai huollon aikana.
Lasermerknad
Skriveren er sertifisert i USA for samsvar med kravene i DHHS 21 CFR, kapittel I, underkapittel J for
laserprodukter av klasse I (1) og er andre steder sertifisert som et laserprodukt av klasse I som samsvarer med
kravene i IEC 60825-1.
Laserprodukter av klasse I anses ikke som helseskadelige. Skriveren inneholder en intern AlGaInP-laser av
klasse IIIb (3b) på nominelt 15 milliwatt, som opererer i bølgelengder på 650–670 nanometer, inne i en
skrivehodeenhet som ikke kan vedlikeholdes. Lasersystemet og skriveren er utformet slik at mennesker ikke
utsettes for laserstråling utover nivået i klasse I under normal drift, vedlikehold eller foreskrevet service.
Meddelande om laser
Skrivaren är certifierad i USA i enlighet med kraven i DHHS 21 CFR kapitel I, underkapitel J för klass I (1)-
laserprodukter, och på andra platser certifierad som en klass I-laserprodukt i enlighet med kraven i IEC 60825-1.
Laserprodukter av klass I anses inte vara skadliga. Skrivaren innehåller en klass IIIb (3b) AlGaInP-laser på
nominellt 15 mW som arbetar inom en våglängd på 650–670 nm och är innesluten i en icke-servicebar
skrivhuvudenhet. Lasersystemet och skrivaren är utformade så att människor aldrig utsätts för laserstrålning
över klass I-nivå under normala förhållanden vid användning, underhåll eller service.
7528
Notices and safety information
15
レーザーについて
本機は、米国において クラス I（1）レーザー製品に対する DHHS 21 CFR、Chapter I、Subchapter J の要件に準
拠し、その他の国では IEC 60825-1 の要件に準拠するクラス I レーザー製品として認可されています。
クラス I レーザー製品は、危険性がないとみなされています。 本機には、クラス IIIb（3b）AlGaInP レーザーが内蔵
されています。これは、650 ～ 670 ナノメートルの波長で、定格 15 ミリワットで動作するレーザーであり、整備不可
のプリントヘッドアセンブリに収容されています。 レーザーシステムとプリンタは、通常の操作、ユーザーによるメンテ
ナンス、または所定のサービス条件の下で、ユーザーがクラス I レベルを超えるレーザー放射に絶対にさらされない
ように設計されています。
레이저 고지사항
프린터는 미국에서 레이저 제품용 DHHS 21 CFR Chapter I, Subchapter J의 요구 사항을 준수하며 이외 지역
에서 IEC 60825-1의 요구 사항을 준수하는 클래스 I(1) 레이저 제품으로 승인되었습니다.
Class I 레이저 제품은 위험한 제품으로 간주되지 않습니다. 프린터에는 650~670 나노미터 범위의 파장 영역
에서 공칭 작동하는 15밀리와트 AlGaInP 레이저인 클래스 IIIb(3b) 레이저가 내부에 포함되어 있으며 서비스
불가 프린트 헤드 어셈블리가 포함되어 있습니다. 레이저 시스템과 프린터는 정상적인 작동
, 사용자 유지 관
리 또는 사전 설명된 서비스 조건에는 사람에게 클래스 I 수준 이상의 레이저 방사가 노출되지 않도록 설계되
었습니다.
激光注意事项
本打印机在美国认证合乎 DHHS 21 CFR Chapter I，Subchapter J 对分类 I（1）激光产品的标准，而在其他
地区则被认证是合乎 IEC 60825-1 的分类 I 激光产品。
一般认为分类 I 激光产品不具有危险性。本打印机内部含有分类 IIIb（3b）的磷化铝镓铟激光，标称值为 15
毫瓦，其工作波长范围在 650–670nm 之间，并被封闭在不可维修的打印头配件中。本激光系统及打印机的
设计，在一般操作、使用者维护或规定内的维修情况下，不会使人体接触分类 I 以上等级的辐射。
雷射聲明
本印表機係經過美國核可，符合 DHHS 21 CFR，Chapter I，Subchapter J 規定的 I (1) 級雷射產品；在美國
以外的地區，為符合 IEC 60825-1 規定的 I 級雷射產品。
根據 I 級雷射產品的規定，這類產品不會對人體造成傷害。 本印表機所採用之 IIIb (3b) 級 AlGaInP 雷射在 650
至 670 奈米 (nanometer) 波長範圍內運作時通常為 15 毫瓦特 (milliwatt)，且含括在不可修復列印頭組件中。 使
用者只要以正確的方法操作及維護保養，並依照先前所述之維修方式進行修護，此印表機與其雷射系統絕不會
產生 I 級以上的放射線，而對人體造成傷害。
Safety information
• The safety of this product is based on testing and approvals of the original design and
specific
components.
The manufacturer is not responsible for safety in the event of use of unauthorized replacement parts.
• The maintenance information for this product has been prepared for use by a professional service person
and is not intended to be used by others.
• There may be an increased risk of electrical shock and personal injury during disassembly and servicing of
this product. Professional service personnel should understand this risk and take necessary precautions.
7528
Notices and safety information
16
CAUTION—SHOCK HAZARD: When you see this symbol, there is a danger from hazardous voltage in
the area of the product where you are working. Unplug the product before you begin, or use caution if
the product must receive power in order to perform the task.
CAUTION—POTENTIAL INJURY: The lithium battery in this product is not intended to be replaced.
There is a danger of explosion if a lithium battery is incorrectly replaced. Do not recharge, disassemble,
or incinerate a lithium battery. Discard used lithium batteries according to the manufacturer's instructions
and local regulations.
Consignes de sécurité
• La sécurité de ce produit est basée sur des tests et certifications de sa conception d'origine et de ses
composants spécifiques. Le fabricant décline toute responsabilité en cas d'utilisation de pièces de rechange
non autorisées.
• Les informations de maintenance de ce produit sont destinées à des professionnels qualifiés et ne sont pas
conçues pour être utilisées par d'autres personnes.
• Il existe un risque potentiel de choc électrique et de blessures lors du démontage et de la maintenance de
ce produit. Le personnel professionnel de maintenance doit comprendre les risques et prendre les
précautions nécessaires.
ATTENTION—RISQUE D'ELECTROCUTION : Ce symbole indique un danger lié à des niveaux de
tension dangereux dans la zone du produit à manipuler. Débranchez le produit avant de commencer, ou
agissez avec prudence si le produit doit être alimenté pour eectuer l'opération.
ATTENTION—RISQUE DE BLESSURE : La batterie lithium de ce produit n'est pas destinée à être
remplacée. Si vous ne respectez pas les instructions de remplacement de la batterie, vous risquez de
provoquer une explosion. Ne rechargez pas, ne désassemblez pas et ne brûlez pas la batterie au
lithium. Mettez les batteries lithium usagées au rebut selon les instructions du fabricant et les
réglementations locales.
Informació de seguretat
• La seguretat d'aquest producte es basa en les proves i les homologacions del disseny original i dels
components específics. El fabricant no és responsable de la seguretat en el cas d'ús de peces de recanvi
no autoritzades.
• La informació de manteniment d'aquest producte s'ha preparat per a l'ús d'un professional tècnic i no per
a l'ús d'altres persones.
• És possible que el risc de descàrrega elèctrica i lesions personals augmenti durant el desmuntatge i les
tasques de manteniment d'aquest producte. El professional tècnic ha de comprendre aquest risc i prendre
les precaucions necessàries.
ATENCIÓ: PERILL DE DESCÀRREGA: Quan vegeu aquest símbol, indica que hi ha un perill de voltatge
elevat en l'àrea del producte on esteu treballant. Desconnecteu el producte abans de començar o
tingueu precaució si el producte ha de rebre alimentació per realitzar la tasca.
ATENCIÓ: POSSIBLES DANYS: La bateria de liti d'aquest producte no ha estat dissenyada perquè se
substitueixi. Hi ha perill d’explosió si no es substitueix correctament la bateria de liti. No recarregueu,
desmunteu o incinereu una bateria de liti. Desfeu-vos de les bateries de liti usades d’acord amb les
instruccions del fabricant i les regulacions locals.
7528
Notices and safety information
17
Información de seguridad
• La seguridad de este producto se basa en las pruebas y comprobaciones del diseño original y los
componentes específicos. El fabricante no se hace responsable de la seguridad en caso de uso de piezas
de repuesto no autorizadas.
• La información de mantenimiento de este producto se ha preparado para su uso por parte de un profesional
de asistencia técnica y no está diseñada para su uso por parte de otros usuarios.
• Es posible que haya un mayor riesgo de descarga eléctrica y daños personales durante el desmontaje y el
mantenimiento de este producto. El personal de asistencia profesional debe conocer este riesgo y tomar
las precauciones necesarias.
PRECAUCIÓN: PELIGRO DE DESCARGAS ELÉCTRICAS Cuando vea este símbolo, existe peligro de
tensiones peligrosas en el área del producto en la que está trabajando. Desconecte el producto antes
de empezar o tenga cuidado si el producto debe recibir alimentación a fin de realizar la tarea.
PRECAUCIÓN: POSIBLES DAÑOS PERSONALES: La batería de litio de este producto no debe
reemplazarse. Existe riesgo de explosión si se sustituye incorrectamente una batería de litio. No
recargue, desmonte ni incinere una batería de litio. Deseche las baterías de litio usadas según las
instrucciones del fabricante y las normativas locales.
Informações sobre segurança
• A segurança deste produto é baseada em testes e aprovações do design original e de componentes
específicos. O fabricante não é responsável por segurança em caso de uso não autorizado de peças de
substituição.
• As informações sobre manutenção deste produto foram preparadas para utilização por um técnico
profissional experiente e não se destinam ao uso por outros.
• Pode haver maior risco de choque elétrico e danos pessoais durante a desmontagem e manutenção deste
produto. Os técnicos profissionais experientes devem entender esses riscos e tomar as precauções
necessárias.
ATENÇÃO—PERIGO DE CHOQUE: Se você vir este símbolo, existe perigo de tensão elétrica na área do
produto onde está trabalhando. Desligue o produto antes de começar ou tenha cuidado se o produto
precisar receber energia para executar a tarefa.
ATENÇÃO — RISCO DE FERIMENTO: A bateria de lítio neste produto não deve ser substituída. Existe o
risco de explosão se uma bateria de lítio for substituída incorretamente. Não recarregue, desmonte nem
incinere uma bateria de lítio. Descarte as baterias de lítio usadas de acordo com as instruções do
fabricante e regulamentos locais.
Informatie over veiligheid
• De veiligheid van dit product is gebaseerd op testen en goedkeuringen van het oorspronkelijke ontwerp
en specifieke onderdelen. De fabrikant is niet verantwoordelijk voor de veiligheid bij gebruik van
ongeautoriseerde vervangende onderdelen.
• De informatie over het onderhoud van dit product is opgesteld voor gebruik door een professionele
onderhoudsmonteur en is niet bedoeld voor gebruik door anderen.
• Tijdens demontage en onderhoud van dit product bestaat mogelijk een hoger risico op elektrische
schokken en lichamelijk letsel. Professionele onderhoudsmonteurs dienen op de hoogte te zijn van dit risico
en de noodzakelijke voorzorgsmaatregelen te nemen.
7528
Notices and safety information
18
LET OP—KANS OP ELEKTRISCHE SCHOK: Wanneer u dit symbool ziet, bestaat er een gevaar voor
gevaarlijke spanning in het gebied van het product waaraan u werkt. Haal de stekker van het product uit
het stopcontact voordat u begint, of let extra goed op als het product stroom nodig heeft om een taak te
kunnen uitvoeren.
LET OP—KANS OP LETSEL: De lithiumbatterij in dit product moet niet worden vervangen. Wanneer de
lithiumbatterij niet juist wordt vervangen, bestaat er explosiegevaar. Probeer nooit lithiumbatterijen op te
laden, open te maken of te verbranden. Gooi gebruikte lithiumbatterijen weg volgens de aanwijzingen
van de fabrikant en houd hierbij de plaatselijke regelgeving in acht.
Informazioni sulla sicurezza
• La sicurezza di questo prodotto è basata sui test e sulle approvazioni del design originale e dei componenti
specifici. Il produttore non è responsabile della sicurezza in caso di utilizzo di parti di ricambio non
autorizzate.
• Le informazioni di manutenzione per questo prodotto sono state predisposte per essere utilizzate da un
tecnico dell'assistenza professionale e non sono state previste per l'uso da parte di altre persone.
• È possibile che vi sia un maggior rischio di scosse elettriche e lesioni personali durante lo smontaggio e la
manutenzione di questo prodotto. Il personale dell'assistenza deve comprendere questo rischio e prendere
le precauzioni necessarie.
ATTENZIONE — PERICOLO DI SCOSSA: Questo simbolo indica la presenza di un rischio per tensioni
pericolose nell'area del prodotto in cui si lavora. Scollegare l'alimentazione prima di iniziare, o prestare
la massima attenzione se per eettuare l'operazione il prodotto deve ricevere l'alimentazione.
ATTENZIONE — PERICOLO DI LESIONI: La batteria al litio contenuto nel prodotto non deve essere
sostituita: in caso di sostituzione errata della batteria al litio, potrebbe verificarsi un'esplosione. Non
ricaricare, smontare o bruciare batterie al litio. Smaltire le batterie al litio usate seguendo le istruzioni del
produttore e le norme locali.
Säkerhetsinformation
• Säkerheten för denna produkt baseras på tester och godkännanden av ursprungsdesignen och av specifika
komponenter. Tillverkaren har inget ansvar vid användning av oauktoriserade reservdelar.
• Underhållsinformationen för produkten är avsedd att användas av utbildade servicetekniker och inte avsedd
att användas av andra.
• Risken för elektriska stötar och personskador kan vara förhöjd vid isärtagning och service av produkten.
Professionell servicepersonal bör vara medvetna om denna risk och vidta nödvändiga försiktighetsåtgärder.
VARNING – RISK FÖR ELCHOCK: När du ser denna symbol är det risk att det finns farlig spänning i den
del av produkten du arbetar med. Koppla från strömmen innan du börjar, eller var försiktig om produkten
måste vara strömförsörjd för att uppgiften ska kunna utföras.
VARNING – RISK FÖR SKADOR: Litiumbatteriet i produkten är inte utbytbart. Om ett litiumbatteri byts ut
på fel sätt finns det risk att det exploderar. Du får inte ladda om, ta isär eller elda upp ett litiumbatteri.
Gör dig av med använda litiumbatterier enligt tillverkarens instruktioner och lokala föreskrifter.
7528
Notices and safety information
19
Sicherheitshinweise
• Die Sicherheit dieses Produkts basiert auf Tests und Zulassungen des Originaldesigns und der
spezifischen
Komponenten. Sofern nicht autorisierte Ersatzteile eingesetzt werden, übernimmt der Hersteller keinerlei
Verantwortung in Bezug auf die Sicherheit dieses Produkts.
• Die Wartungsinformationen für dieses Produkt wurden für ausgebildete Servicemitarbeiter
zusammengestellt und dürfen nicht von anderen verwendet werden.
• Möglicherweise besteht bei der Demontage und Wartung dieses Produkts eine erhöhte Stromschlag- und
Verletzungsgefahr. Ausgebildete Servicemitarbeiter sollten sich dieser Gefahr bewusst sein und die
notwendigen Vorsichtsmaßnahmen ergreifen.
VORSICHT - STROMSCHLAGGEFAHR: Wenn Sie dieses Symbol sehen, besteht eine Gefahr durch
gefährliche Spannungen in dem Produktbereich, in dem Sie arbeiten. Trennen Sie das Produkt von
seiner Stromverbindung, bevor Sie beginnen, oder gehen Sie vorsichtig vor, wenn das Produkt für die
Durchführung der Aufgabe mit Strom versorgt werden muss.
VORSICHT - VERLETZUNGSGEFAHR: Die Lithiumbatterie in diesem Produkt darf nicht ausgetauscht
werden. Wird eine Lithiumbatterie nicht ordnungsgemäß ausgetauscht, besteht Explosionsgefahr.
Lithiumbatterien dürfen auf keinen Fall wieder aufgeladen, auseinander genommen oder verbrannt
werden. Befolgen Sie zum Entsorgen verbrauchter Lithiumbatterien die Anweisungen des Herstellers
und die örtlichen Bestimmungen.
Sikkerhedsoplysninger
• Sikkerheden for dette produkt er baseret på afprøvning og godkendelser af det oprindelige design og
specifikke komponenter. Producenten er ikke ansvarlig for sikkerhed i tilfælde af brug af uautoriserede dele
til udskiftning.
• Vedligeholdelsesoplysninger om dette produkt er udarbejdet til brug af en kvalificeret servicetekniker og
er ikke beregnet til at blive brugt af andre.
• Der kan være en forøget risiko for elektrisk stød eller personskade ved afmontering og service af dette
produkt. Professionelt servicepersonale bør forstå denne risiko og tage nødvendige forholdsregler.
FORSIGTIG! RISIKO FOR ELEKTRISK STØD: Når du ser dette symbol, er der risiko for elektrisk
spænding i nærheden af produktet, hvor du arbejder. Tag strømstikket ud inden du begynder, eller udvis
forsigtighed, hvis produktet skal modtage strøm for at udføre opgaven.
FORSIGTIG! RISIKO FOR SKADE: Litium-batteriet i dette produkt er ikke beregnet til at blive udskiftet.
Der er fare for eksplosion, hvis et litium-batteri udskiftes forkert. Du må ikke genoplade, demontere eller
arænde et litium-batteri. Brugte litium-batterier skal bortskaes i overensstemmelse med
producentens instruktioner og lokale retningslinjer.
Sikkerhetsinformasjon
• Sikkerheten til dette produktet er basert på testing og godkjenning av originaldesignet og bestemte
komponenter. Produsenten er ikke ansvarlig for sikkerheten ved bruk av uautoriserte reservedeler.
• Vedlikeholdsinformasjonen for dette produktet er tilrettelagt for bruk av profesjonelt servicepersonale, og
er ikke ment for bruk av andre.
• Det kan være en økt risiko for elektrisk støt og personskade under demontering og vedlikehold av produktet.
Profesjonelt servicepersonell må være innforstått med denne risikoen og ta nødvendige forholdsregler.
7528
Notices and safety information
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
-
367
-
368
-
369
-
370
-
371
-
372
-
373
-
374
-
375
-
376
-
377
-
378
-
379
-
380
-
381
-
382
-
383
-
384
-
385
-
386
-
387
-
388
-
389
-
390
-
391
-
392
-
393
-
394
-
395
-
396
-
397
-
398
-
399
-
400
-
401
-
402
-
403
-
404
-
405
-
406
-
407
-
408
-
409
-
410
-
411
-
412
-
413
-
414
-
415
-
416
-
417
-
418
-
419
-
420
-
421
-
422
-
423
-
424
-
425
-
426
-
427
-
428
-
429
-
430
-
431
-
432
-
433
-
434
-
435
-
436
-
437
-
438
-
439
-
440
-
441
-
442
-
443
-
444
-
445
-
446
-
447
-
448
-
449
-
450
-
451
-
452
-
453
-
454
-
455
-
456
-
457
-
458
-
459
-
460
-
461
-
462
-
463
-
464
-
465
-
466
-
467
-
468
-
469
-
470
-
471
-
472
-
473
-
474
-
475
-
476
-
477
-
478
-
479
-
480
-
481
-
482
-
483
-
484
-
485
-
486
-
487
-
488
-
489
-
490
-
491
-
492
-
493
-
494
-
495
-
496
-
497
-
498
-
499
-
500
-
501
-
502
-
503
-
504
-
505
-
506
-
507
-
508
-
509
-
510
-
511
-
512
-
513
-
514
-
515
-
516
-
517
-
518
-
519
-
520
-
521
-
522
-
523
-
524
-
525
-
526
-
527
-
528
-
529
-
530
-
531
-
532
-
533
-
534
-
535
-
536
-
537
-
538
-
539
-
540
-
541
-
542
-
543
-
544
-
545
-
546
-
547
-
548
-
549
-
550
-
551
-
552
-
553
-
554
-
555
-
556
-
557
-
558
-
559
-
560
-
561
-
562
-
563
-
564
-
565
-
566
-
567
-
568
-
569
-
570
-
571
-
572
-
573
-
574
-
575
Lexmark CX725 Series User manual
- Category
- Laser/LED printers
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Lexmark X925 Maintenance Manual
-
Lexmark X782 Clearing Jams Manual
-
-
-
Lexmark X792 User manual
-
-
Lexmark X850E User manual
-
Lexmark X264DN Maintenance Manual
-
Lexmark X422 User manual
-
Other documents
-
Konica Minolta Bizhub 4020 User manual
-
Dell 2330DN User manual
-
OKI ES3640 MFP Component Replacement Manual
-
Portatree Auto Cut Time Slip Printer Operating instructions
-
HP C30D User manual
-
Compuprint TSP40plus User guide
-
Arrive InfoPoint ID-1000 Installation guide
-
CARLO GAVAZZI MPF2-115RS User manual
-
Durst Rho 700 User manual
-
CARLO GAVAZZI MPF2-115RS Owner's manual
