Humandata EDA-011-40 User manual

Brand
Humandata
Model
EDA-011-40
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
Cyclone 10 LP F484
USB-FPGA Board
EDA-011 Series
User’s Manual
Ver. 1.0
Table of Contents
Revision History .............................................................................................. 1
Introduction .................................................................................................... 1
Unused Pins [IMPORTANT] ........................................................................... 1
1. Specifications ..................................................................................................... 2
2. Overview ............................................................................................................ 3
2.1. Name of Parts .......................................................................................................3
2.2. Block Diagram ......................................................................................................4
2.3. Power Supply ........................................................................................................5
2.4. I/O Power Supply .................................................................................................5
2.5. Clock ......................................................................................................................6
2.6. User Switch ..........................................................................................................6
2.7. User LED ..............................................................................................................6
2.8. SDRAM .................................................................................................................6
2.9. SPI-Flash Memory ...............................................................................................6
2.10. Debug I/F ............................................................................................................6
2.11. Setting Switch ....................................................................................................7
2.12. USB Controller (FT2232H) ...............................................................................7
3. FPGA Configuration ........................................................................................... 8
3.1. Using Original Tool ..............................................................................................8
3.2. Using JTAG Download cable ...............................................................................9
3.3. Using Configuration Device ................................................................................9
4. Device Driver ..................................................................................................... 9
5. Factory Setting of FT232H EEPROM ............................................................... 10
6. Documentation and User Support .................................................................... 11
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. In case item 2, above, HuMANDATA guarantee its products for a period of 60 days from the date of shipping.
4. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
5. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
6. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
7. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
8. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
9. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
10. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
11. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
12. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
13. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
14. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
EDA-011 v1.0
Revision History
Date
Revision
Description
March 9, 2018 v1.0 Initial release
Introduction
Thank you for purchasing our product EDA-011.
EDA-011 is a USB-FPGA board with USB interface equipped with Intel FPGA
Cyclone 10 LP series and FTDI's USB controller FT2232H.
By using the original configuration tool “BBC[EDA-011]”, no download cable or
Intel developing environment is needed to configure FPGA and configuration device
on the board.
Unused Pins [IMPORTANT]
For supporting device migration, some I/O pins of this board are configured to
power supply pins. These pins are needed to be set as a dummy input depending on
the device grades, and please do not use them.
To set all unused pins as input pins, please refer to the steps below:
1. Open “Assignments” and click “Device”
2. Click “Device and Pin Options…” button
3. Open “Unused Pins” category
4. Set “Reserve all unused pins” as “As input tri-stated”
2
EDA-011 v1.0
1. Specifications
Model Name
EDA-011-16 EDA-011-40 EDA-011-55 EDA-011-80 EDA-011-120
FPGA
10CL016Y
F484C8G
10CL040Y
F484C8G
10CL055Y
F484C8G
10CL080Y
F484C8G
10CL120Y
F484C8G
Power Input
DC 5.0 [V] (Internal power is generated by on-board regulator)
User I/O
100 (CNA:50, CNB:50)
On-Board Clock
50 [MHz] (External inputs are available)
USB 2.0 Controller
FT2232H (FTDI)
Config. Device
MT25QL128ABA1ESE-0SIT (Micron, 128Mbit)
SPI-FLASH
MT25QL128ABA1ESE-0SIT (Micron, 128Mbit)
SDRAM
AS4C16M16SA-7BCN (Alliance Memory, 256Mbit)
User LED
2
User Switch
2 (Push x 1, DIP x 1bit)
Status LED
Power (red) x1, Done (blue) x1
Power-On Reset
240 [ms] typ. (Config. reset signal)
User I/Os
66-pin through-hole
dia. 0.9 (typ.) [mm], 100[mil]/2.54 [mm] pitch
JTAG Connector
DIL 10-pin socket, 2.54 [mm] pitch
PCB
6 Layer FR-4 t1.6 [mm] Immersion gold
Dimensions
3.386" x 2.126" (86 x 54 [mm])
Weight
32 [g] typ.
Accessories
DIL10 long pin header (Mounted) x1
DIL80 pin header x 2
USB 2.0 cable x 1
RoHS Compliance
YES
* There may be cases that these parts and specifications are changed.
3
EDA-011 v1.0
2. Overview
2.1. Name of Parts
Component Side
Solder Side
SPI-FLASH
Oscillator
JTAG
Config. Device
User LEDs
Setting/User SW
Debug I/F
Done LED
4
EDA-011 v1.0
2.2. Block Diagram
High Speed
USB Controller
FT2232H
JTAG
Config. Device
JTAG
Buffer
SDRAM
Ch.A
Ch.B C o nfig.
User
Reset
User I/Os CN B
User I/Os CNA
50
V IO(B) INPUT
5.0 V INPUT
Power LED (3.3V)
Power Circuit
3.3V, 2.5V, 1.2V
2
2
User LED
Config. Switch
DONE LED
USB
3 .3V Output (Option)
5.0 V INPUT
50
EDA-011 Rev.A
Cyclone 10 LP
10CL016YF484C8G
10CL040YF484C8G
10CL055YF484C8G
10CL080YF484C8G
10CL120YF484C8G
SPI-FLASH
Pus h Switch x1
S l ide Switch x1
Oscillator
POR
5
EDA-011 v1.0
2.3. Power Supply
This board operates from single DC 5.0 V power supply from CNA and CNB
connectors. The external power supply should be sufficient and stabilized.
And also USB bus power can be used by setting JP1. Current supply might be
shortage depending on your FPGA design.
SHORT: 1-3 and 2-4 (factory setting)
- Powered from user I/O connector only
SHORT: 1-2 and 3-4
- Powered by USB bus power and user I/O connector
2.4. I/O Power Supply
3.3V generated on the board is supplied to I/O power of CNA. Please input some
external voltage to VIO(B), I/O power of CNB, depending on your FPGA design.
This can’t be left to be unconnected.
FPGA Bank
Bank Group
VCCIO
Function
1 A V33A IOA
2
B
VIO(B)
IOB
3 - V33A SDRAM, SPI-FLASH
4
-
V33A
SDRAM, SPI-FLASH
5 B VIO(B) IOB
6
B
VIO(B)
IOB
7 A V33A IOA
8
A
V33A
IOA
6
EDA-011 v1.0
2.5. Clock
A 50 MHz oscillator (U1) is equipped as an on-board clock.
Some user I/O pins can be used for clock input pins.
For more details, please refer to the circuit schematics.
2.6. User Switch
You can use SW2[2] and SW1 for general purpose. They are pulled up,
so you can input low level signal to the FPGA when you push them.
2.7. User LED
You can use L1 and L2 for general purpose. They are active low.
2.8. SDRAM
You can use U1 for general purpose.
For more details, please refer to a data sheet of the device.
2.9. SPI-Flash Memory
An SPI-FLASH memory (U3) is equipped. You can use it for general
purpose.
2.10. Debug I/F
These are pads for serial communication. They are connected directly to
FPGA through a serial resistance.
7
EDA-011 v1.0
2.11. Setting Switch
You can use SW2 to set a configuration mode of the FPGA.
SW2
Configuration Mode
1
2
MSEL
ASW
PS (Passive Serial)
ON
X
AS (Active Serial)
OFF
X
ON: Low, X: Don’t Care
PS mode : Configured by JTAG or original configuration tool
AS mode : Configured by configuration device.
2.12. USB Controller (FT2232H)
The FT2232H is mounted on this board as a USB controller IC. FT2232H is a dual
channel IC, so 2 channels (A/B) is recognized on a PC.
Channel A is connected to FPGA user I/O pin for user communication. Channel B is
connected to FPGA configuration control pin.
By setting JP2, reset function and EEPROM are available.
JP2[1-2]
SHORT
: use EEPROM for FT2232H (factory setting)
OPEN
: not use EEPROM for FT2232H
- When you make FT2232H to be recognized by PC in its
default setting (default scripter and A/B channel is set to
UART mode), please set this jumper OPEN.
JP2[3-4]
SHORT
: connect FPGA pin to FT2232H reset
OPEN
: not connect (factory setting)
- When you use BBC[EDA-011], please set this jumper
OPEN.
8
EDA-011 v1.0
3. FPGA Configuration
3.1. Using Original Tool
By using the original configuration tool
“BBC[EDA-011]”, following function is
available without download cable.
● FPGA configuration
● Write and Erace configuration device
BBC[EDA-011] is available for free from a support page.
RBF file is supported. You can make the file by the following step.
[Device and Pin Options – Programming Files]
When you use the data to write configuration device, apply the following settings.
[Device and Pin Options – Configuration]
- Configuration scheme = Active Serial
- Configuration device = EPCQ128A
9
EDA-011 v1.0
3.2. Using JTAG Download cable
Download cable is needed to use Intel tool (SignalTap II etc.). Pin assignment is as
follows.
CN1
3.3. Using Configuration Device
Configuration data written in the configuration device will be configured to the
FPGA automatically when power is applied. To use this function, set configuration
mode to “Active Serial” mode.
Do not download inaccurate configuration data. It would damage the FPGA and
peripheral circuit.
4. Device Driver
To recognize USB controller, installing device driver is needed. The first time
EDA-011 is connected to a PC, installing is required by Operation System.
The device driver and installation instruction are available from a support page.
Signal Name
JTAG Pin
Signal Name
TCK 1 2 GND
TDO
3
4
VCC
TMS 5 6 -
-
7
8
-
TDI 9 10 GND
10
EDA-011 v1.0
5. Factory Setting of FT232H EEPROM
Factory presetting is as follows. The other items are not changed from the default.
Item Value
Vendor ID 0F87
Product ID
1047
Bus Powered Check
Max Bus Power
500
Manufacturer HuMANDATA
Product Description
EDA-011 HuMANDATA
Serial Number Enabled Disable
Port A - Hardware
245 FIFO
Port A - Driver Virtual COM Port
Port B - Hardware
245 FIFO
Port B - Driver D2XX Direct
11
EDA-011 v1.0
6. Documentation and User Support
The following documents and other supports are available at
http://www.hdl.co.jp/en/spc/EDA/eda-011/
Circuit Schematic
Pin List
Outline Drawing
Net List
Original Configuration Tool “BBC[EDA-011]”
Device Driver
Device Driver Installation Instruction
… and more.
Cyclone 10 LP F484 USB-FPGA Board
EDA-011 Series
User’s Manual
Ver. 1.0. ......................................... March 9, 2018
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: https://www2.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Humandata EDA-011-40 User manual

Brand
Humandata
Model
EDA-011-40
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers