Humandata EDA-004Z User manual

Brand
Humandata
Model
EDA-004Z
Category
Software manuals
Type
User manual
*: without MRAM version of non-Z product.
HuMANDATA LTD.
Cyclone III USB-FPGA Board
EDA-004Z (*)
User’s Manual
Ver. 1.0
Table of Contents
Revision History .............................................................................................. 1
Introduction .................................................................................................... 1
1. Specifications ..................................................................................................... 2
2. Overview ............................................................................................................ 3
2.1. Name of Parts .......................................................................................................3
2.2. Block Diagram ......................................................................................................4
2.3. Power Supply ........................................................................................................5
2.4. Clock ......................................................................................................................5
2.5. Setting Switch (SW1, JP3) ..................................................................................5
2.6. Development Environment .................................................................................6
3. USB Driver ........................................................................................................ 7
3.1. Install ....................................................................................................................7
3.2. Uninstall ...............................................................................................................9
4. FPGA Configuration ......................................................................................... 10
4.1. USB Configuration ............................................................................................ 10
4.2. Creating RBF File .............................................................................................. 11
4.3. JTAG Configuration .......................................................................................... 12
5. Initial setting of EEPROM for FT2232H .......................................................... 13
6. Additional Documentation and User Support ................................................... 14
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
4. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
5. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
6. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
7. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
8. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
9. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
10. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
11. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
12. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
13. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
EDA-004Z (Ver. 1.0) 1
Revision History
Date
Version
Description
Jun. 7, 2012 1.0 Initial release
Introduction
Thank you for purchasing our product.
EDA-004Z is an evaluation board equipped with Altera FPGA, power circuit, reset
circuit, crystal, and configuration device.
FTDI’s FT2232H is mounted for USB interface. Its channel A is assigned for user
communication interface, and FTDI’s virtual COM port and direct driver are
available.
Its channel B is assigned for FPGA configuration. By using our original
programming software, it is possible to configure the FPGA and program the EPCS
Memory. This feature does not require Altera’s programming software and any
download cables.
EDA-004Z can provide you very convenient and easy-to-use environment.
EDA-004Z is a without MRAM model of EDA-004.
* The explanations and screenshots given in this manual are based on QuartusII Ver. 10.1.
EDA-004Z (Ver. 1.0) 2
1. Specifications
Model Name
EDA-004Z
FPGA
EP3C55F780C8N
USB Interface
FT2232H (FTDI)
Power Input
DC 5.0 [V] (Self power operation only)
Config. Device
EPCS16SI8N (Altera, 16Mbit)
MRAM
Unmounted
Dimensions
3.386" x 2.126" (86 x 54 [mm])
Weight
35 [g] typ.
User I/Os
100
User I/O Connectors
66-pin through-hole
dia. 0.9 [mm], 100[mil]/2.54 [mm] pitch
User Switch
1
User LEDs
3
On-Board Clock
50 [MHz] (External inputs are available)
Status LEDs
2 : POWER (Red), DONE (Blue)
Power-On Reset
140 [ms] min. (Configuration reset signal)
JTAG Connector
DIL 10-pin socket, 2.54 [mm] pitch
PCB
6 Layer FR-4 t1.6 [mm] Immersion gold
Accessories
DIL10 long pin header (Attached to the JTAG connector)
DIL80 pin headers (Cuttable)
USB Cable (1.8m)
RoHS Compliance
YES
* There may be cases that these parts and specifications are changed.
EDA-004Z (Ver. 1.0) 3
2. Overview
2.1. Name of Parts
Component Side
Solder Side
User I/Os (CNB)
User I/Os (CNA)
User LED x3
User Switch
Setting Switch
JTAG Connector
FPGA
Config. Device
EEPROM
FT2232H Reset
Jumper
Done LED (Blue)
Power LED (Red)
Oscillator
(50 MHz)
EEPROM Access
Jumper
FT2232H
EDA-004Z (Ver. 1.0) 4
2.2. Block Diagram
Hi-Speed
US B Controller
FT2232H
Cy clone-III
EP3C55
F780C8N
JTAG
Config. Device
EPCS16(16Mbit)
3.3 V OUTPUT
JTAG
Buffer
USB
C o nnector
DONE LED
E xt ernal CLK
E xt ernal CLK
5.0 V INPUT
5.0 V INPUT3.3 V OUTPUT
No Memory Device
Ch.A
Ch.B C o nfig.
Us er
Reset
POR
Config. Switch
Oscillator
50
MHz
Us er LEDs
Power LED(3.3V)
Power Circuit
3.3V, 2.5V, 1.2V
.JIC
User Switch
User I/Os CNB
User I/Os CNA
50
Protective Resistors
50
Protective Resistors
3
2
2
EDA-004Z Rev.A
EDA-004Z (Ver. 1.0) 5
2.3. Power Supply
This board operates from external 5.0V input. You can use external 5.0V input from
CNA and CNB. The external power supply should be sufficient and stabilized.
FT2232H operates in self-power mode.
Please note that you can not use USB Bus power.
Internally required 3.3V, 2.5V and 1.2V are generated by on-boarded regulators.
2.4. Clock
A crystal supplies 12MHz to the FT2232H, and an oscillator supplies 50MHz to the
FPGA. You can input external clock through CNA and CNB connectors.
For details, please see circuit schematics and pin assignment.
2.5. Setting Switch (SW1)
SW1 is configuration mode setting switch. For more information of each pins,
please refer to CycloneIII user guide.
SW1
1
2
3
4
NET LABEL
MSEL3
MSEL2
MSEL1
MSEL0
Default
ON
ON
ON
ON
Function
Configuration Mode
Config. Mode
MSEL3
MSEL2
MSEL1
MSEL0
AS *1
OFF
OFF
ON
OFF
PS *2
ON
ON
ON
ON
JTAG
X
X
X
X
X: Don’t Care
(*1) For FPGA configuration from the configuration device.
(*2) For FPGA configuration from USB using original programming software “BBC
[EDA-004]”. Please refer to the chapter 4.
2.6. FT2232H Reset Jumper (JP3)
This jumper is used to connect a port of FPGA to the FT2232H’s reset signal input.
When the FPGA is not configured, FT2232H will be reset by the FPGA.
When using the programming software, remove this jumper.
EDA-004Z (Ver. 1.0) 6
2.7. FT2232H EEPROM Access Jumper (JP5)
This jumper is connected the EEPROM to the FT2232H. When you would like to
start up the FT2232H with its default mode and port description, remove this
jumper.
For more details, please refer to chapter 5.
2.8. Development Environment
To develop and design FPGA internal circuit, you need to prepare circuit editor,
HDL editor or logic synthesis tool. These tools are provided by Altera as QuartusII.
When you use them, you need an internet license. The version of QuartusII when
EDA-004 developed is Ver.10.1.
EDA-004Z (Ver. 1.0) 7
3. USB Driver
3.1. Install
To configure and communicate the FPGA, you need to install device drivers on your
PC. The device driver was established by FTDI. Please download the driver file
named from our support page. For installation, please follow the steps below.
(*Windows XP is used in this example)
1. Select “No, not this time” then click “Next”.
3. Browse the driv
er files which you downloaded
from our support page.
2. Select “Install from a list…” then click “Next”.
4. “EDA-004” will be installed.
5. Keep coming, “ED-CONFIG” and “USB Serial Port” will be recognized. Please
repeat the same process for each devices.
*Non-WHQL compliant device driver will pop up a warning dialog window. When
you warned, please click “YES” or “Continue Anyway”.
EDA-004Z (Ver. 1.0) 8
If the installation is finished successfully, three hardwares will be listed in device
manager.
EDA-004Z (Ver. 1.0) 9
3.2. Uninstall
To uninstall the device driver, please follow the steps below. Please make sure that
the EDA-004 is not attached to your PC before you operate device un-installation.
1. Open “Control Panel” then click “Add or Remove programs”.
2. Click “Continue”.
3. Click “Finish”.
EDA-004Z (Ver. 1.0) 10
4. FPGA Configuration
4.1. USB Configuration
By using our original programming software “BBC
[EDA-004]”, it’s possible to configure the FPGA through
USB interface.
The programming software is available at EDA-004Z support page.
FPGA configuration
Exit the software
Open design file (RBF)
Reset FPGA
Execute configuration
Switch setting note
(please set SW1 as displayed)
Report display area
(to clear the text, double click in this area)
EPCS Access
Exit the software
Process time
Open design file (RBF)
Setting process flow
(Switch Bilk/Sector Erase, Erase only, No
Verify …)
Execute process flow
TOP: EPCS access from BBC
BOTTOM: Configure FPGA from EPCS
EDA-004Z (Ver. 1.0) 11
Option
Exit the software
Save setting for automatically restore
Uncheck to use unique port description.
show the active device list
Download cable is required to access the FPGA via
JTAG interface (e.g., Signal Tap),
4.2. Generating RBF File
BBC [EDA-004] uses an RBF (Raw Binary File) format design file. To generate an
RBF file in QuartusII, please follow the steps below.
1. Click [Device and Pin Options...] from [Assignment -> Device] dialog
Notes
EDA-004Z (Ver. 1.0) 12
2. Select [Programming Files] menu, and check [Raw Binary File (.rbf)]
4.3. JTAG Configuration
JTAG interface is also available to configure the FPGA and download design file
into the configuration device (EPCS memory).
CN2
Signal Name
Pin No.
Net Label
TCK
1
2
GND
TDO
3
4
V33A
TMS
5
6
-
-
7
8
-
TDI
9
10
GND
EDA-004Z (Ver. 1.0) 13
5. Initial setting of EEPROM for FT2232H
The EEPROM for FT2232H is configured as below.
(FTDI MPROG Version 3.5)
EDA-004Z (Ver. 1.0) 14
6. Additional Documentation and User Support
The following documents and other supports are available at
http://www.hdl.co.jp/en/spc/EDA/eda-004Z/
Circuit Schematic
Pin Assignment Document
Dimensional drawing
PCB drawing
Net List
Device drivers
Programming software
… and more.
Cyclone III USB-FPGA Board
EDA-004Z
User’s Manual
Ver. 1.0 ............................................. Jun. 7, 2012
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: http://www.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Humandata EDA-004Z User manual

Brand
Humandata
Model
EDA-004Z
Category
Software manuals
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers