HuMANDATA LTD.
Cyclone V USB-FPGA Board
EDA-008 Series
User’s Manual
Ver. 1.0
Table of Contents
z Revision History ................................................................................................. 1
z Introduction ........................................................................................................ 1
1. Specifications ......................................................................................................... 2
2. Overview ................................................................................................................ 3
2.1. Name of Parts .................................................................................................... 3
2.2. Block Diagram ................................................................................................... 4
2.3. Clock ................................................................................................................... 4
2.4. MRAM ................................................................................................................ 4
2.5. Power Supply ..................................................................................................... 5
2.6. I/O Power Supply ............................................................................................... 5
2.7. USB Controller .................................................................................................. 6
2.8. Setting Switch .................................................................................................... 6
3. FPGA Configuration .............................................................................................. 7
3.1. Using Original Tool ............................................................................................ 7
3.2. Using JTAG Download cable ............................................................................. 7
3.3. Using Configuration Device .............................................................................. 8
4. Device Driver ......................................................................................................... 8
5. Factory Setting of FT2232H EEPROM ................................................................. 9
6. Documentation and User Support ........................................................................ 10
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. In case item 2, above, HuMANDATA guarantee its products for a period of 60 days from the date of shipping.
4. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
5. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
6. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
7. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
8. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
9. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
10. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
11. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
12. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
13. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
14. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
EDA-008 v1.0
z Revision History
Date Revision Description
May. 2, 2014 v1.0 Initial release
z Introduction
Thank you for purchasing our product EDA-008.
EDA-008 is an evaluation board with USB interface equipped with ALTERA FPGA
Cyclone V series and FTDI's FT2232H.
By using the original configuration tool “BBC[EDA-008]”, no download cable or
ALTERA developing environment is needed to configure FPGA and configuration
device on the board.
2
EDA-008 v1.0
1. Specifications
Model Name EDA-008
FPGA 5CEBA4F23C8N
USB Interface FT2232H (FTDI)
* Ch.A is available for user communication.
Config. Device N25Q032 (Micron, 32Mbit)
MRAM MR2A16AMA35 (Everspin, 4Mbit)
Power Input DC 5.0 [V]
On-Board Clock 50 [MHz]
User LED 2
User Switch 2 (Push x 1, DIP x 1bit)
Status LED Power (red) x1, Done (blue) x1
Power-On Reset 240 [ms] typ. (Config. reset signal)
User I/Os 66-pin through-hole
dia. 0.9 (typ.) [mm], 100[mil]/2.54 [mm] pitch
JTAG Connector DIL 10-pin socket, 2.54 [mm] pitch
PCB 6 Layer FR-4 t1.6 [mm] Immersion gold
Dimensions 3.386" x 2.126" (86 x 54 [mm])
Weight 35 [g] typ.
Accessories
DIL10 long pin header (Mounted) x1
DIL80 pin header x 2
USB cable (1.8m) x 1
RoHS Compliance YES
* There may be cases that these parts and specifications are changed.
3
EDA-008 v1.0
2. Overview
2.1. Name of Parts
Component Side
Solder Side
VIO (B)
Setting Jumper
User I/Os
(CNB)
Power
LED
USB Bus Power
Setting Jumper
FT2232H
Setting Jumper
FPGA
USB
Connector
Config.
Device
JTAG
MRAM
Ocillator
User LED
User SW
Config. SW
User I/Os
(CN
A
)
4
EDA-008 v1.0
2.2. Block Diagram
High Speed
USB Controller
FT2232H
JTAG
Config. Device
JTAG
Buffer
MRAM
(4Mbit)
Ch.A
Ch.B Config.
User
Reset
User I/Os CNB
User I/Os CNA
50
ESD Protection
VIO(B) INPUT
5.0 V INPUT
Cyclone V
5CEBA4F23C8N
Power LED (3.3V)
Power Circuit
2.5V, 1.8V, 1.2V
2
User Switch
Push , DIP
2
User LED
Config. Switch
DONE LED
USB
3.3V Output (Option)
5.0 V INPUT
Oscillator
50
MHz
50
ESD Protection
EDA-008 Rev.B
.jic
2.3. Clock
A 50 MHz is equipped as on-board clock. External clock can be input from user I/Os.
For more details, please refer to the circuit schematics.
2.4. MRAM
MRAM is a non-volatile memory. Write/Read cycles are practically unlimited. It is
very useful and can be used as ROM and RAM.
5
EDA-008 v1.0
2.5. Power Supply
This board operates from single DC 5.0 V power supply from user I/O connector (3rd
and 4th pin of CNA and CNB). The external power supply should be sufficient and
stabilized. You can also use USB bus power by setting JP1.
OPEN (factory setting)
Powered from user I/O connector only
1-2, 3-4: Short
Powered by USB bus power and user I/O connector
(Depending on FPGA design, power current may be
insufficient in USB only powering)
2.6. I/O Power Supply
FPGA banks are divided into two groups as follows.
FPGA BANK Vccio BANK Group
3A V33A A
3B V33A A
4A V33A A
5A V33A A
5B V33A A
7A VIO(B) B
8A VIO(B) B
Vccio for Bank Group A/B are separated. I/O power supply for Bank Group A is
fixed to V33A (3.3V). Bank Group B can be changed by setting RJ1.
For more details, please refer to the circuit schematics.
RJ1[1-2] VIO(B) is powered by V33A
RJ1[2-3]
VIO(B) is powered by CNB
6
EDA-008 v1.0
2.7. USB Controller
FTDI’s FT2232H is mounted as USB controller IC. By connecting to a PC, two
channels (A/B) will be recognized.
Chanel A is connected to pins of the FPGA for user communication.
By setting JP4, reset function and EEPROM are available.
JP4 [1-2]
Short (factory setting):
EEPROM for FT2232H is available
Open
EEPROM for FT2232H is disabled.
JP4 [3-4]
Short
FPGA pin is connected to FT2232H’s reset input pin
- By setting FPGA pin to High, FT2232H will be in
its reset mode.
Open (factory setting)
- To use original configuration tool, set this open
2.8. Setting Switch
You can use SW2 to set a configuration mode of the FPGA.
1 2 Configuration Mode
MSEL1 ASW22
ON User PS
OFF User AS
ON: Low
z AS mode : to use to configuration device.
z PS mode : to configure the FPGA from a JTAG I/F or using BBC[EDA-008].
7
EDA-008 v1.0
3. FPGA Configuration
3.1. Using Original Tool
By using the original configuration tool “BBC[EDA-008]”, following function is
available without download cable.
FPGA configuration
Write and Erace configuration device
BBC[EDA-008] is available for free from a support page.
http://www.hdl.co.jp/en/spc/EDA/eda-008/
3.2. Using JTAG Download cable
Download cable is needed to use ALTERA tool (SignalTap II etc.). Pin assignment is
as follows.
Signal Name JTAG Pin Signal Name
TCK 1 2 GND
TDO 3 4 VCC
TMS 5 6 -
- 7 8 -
TDI 9 10 GND
8
EDA-008 v1.0
3.3. Using Configuration Device
Configuration data written in the configuration device will be configured to the
FPGA automatically when power is applied. To use this function, set configuration
mode to “Active Serial” mode.
Do not download inaccurate configuration data. It would damage the FPGA and
peripheral circuit.
4. Device Driver
To recognize USB controller, installing device driver is needed. The first time
EDA-008 is connected to a PC, installing it is required by Operation System.
The device driver is available at the support page.
9
EDA-008 v1.0
5. Factory Setting of FT2232H EEPROM
Factory presetting is as follows. The other items are not changed from the default.
10
EDA-008 v1.0
6. Documentation and User Support
The following documents and other supports are available at
http://www.hdl.co.jp/en/spc/EDA/eda-008/
z Circuit Schematic
z Pin List
z Dimensional drawing
z Net List
z Original Configuration Tool “BBC[EDA-008]”
z Device Driver
… and more.
Cyclone V USB-FPGA Board
EDA-008 Series
User’s Manual
Ver. 1.0 ................................................ May. 2, 2014
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: http://www.hdl.co.jp/en/ (Global)
http://www.hdl.co.jp/ (Japan)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Humandata EDA-302-A4 User manual
-
Humandata EDA-009 User manual
-
Humandata EDA-011-40 User manual
-
Humandata EDA-004Z User manual
-
Humandata EDA-301 User manual
-
Humandata EDA-004 User manual
-
Humandata ACM-027-A4 User manual
-
Humandata EDA-004 User manual
-
Humandata EDX-303-50 User manual
-
Humandata ACM-114-80 User manual
