Anviz OA1000 Series Quick start guide

Type
Quick start guide
Incorrect method:
Tilt sensor. Use fingertip.Place finger away from
the center of the sensor.
Select [User]
Main
2012-03-09 08:08:16
Setting AdvancedApplication
ESC/Back
DataUserEnroll
Select [Add]
Press [OK]
Press [OK]
Main User
Add Modify SearchDel
2012-03-09 08:08:16
ESC/Back
Registered
Users 1
Fingerprints 1
Please input user information and follow with voice
prompt to enroll fingerprint Press[M] to save and exit.
2012-03-09 08:08:16
Menu/Save ESC/Back
Enroll FP
Mode
Picture
User Add
ID
Name
Password
Card No.
Dept
Admin
Group ID
hqtrs
No
0-NC
OA1000 Series Multimedia fingerprint terminal

Correct method:
Operation Guide
Enroll User:
Place finger in the center of
the sensor.
Place finger flatly and
smoothly on the sensor.
Package List

Reader Appearance
Connector Jack
2
Instruction Package
COMPACT
CD OM
EN CH
windows
FOR
Windows 98
Windows 2000
Windows XP
Windows Vista
Windows 7
Accessory Package
1
Reader
LCD
Camera
Confirm & Navigation
Fingerprint Sensor
Card Reader Area
Shortcut Key
Num. & Letter
Menu Delete
EXIT & Power On/Off
State Switch
Prompt:Please refer to the
User Manual in the disk for
details
Input ID
Password
0
12345
Enter management interface:
1 Press “0” and [OK]
2 Input default password 12345
3 Press [OK] enter
LCD
Camera
Confirm & Navigation
Fingerprint Sensor
Shortcut Key
Num. & Letter
Menu Delete
EXIT & Power On/Off
State Switch
Card
or
All manuals and user guides at all-guides.com
all-guides.com
1
2
3
Set Communication parameter:
Press [OK] Press [OK]
Select [Advanced]
Main
2012-03-09 08:08:16
ESC/Back
Setting AdvancedApplication
DataUserEnroll
Select [Comm.]
Main Advanced
2012-03-09 08:08:16
ESC/Back
Group
Mode
Time Zone
Comm.
Access
Snapshot
Set communication parameter, Press[Menu]
to and exit save
2012-03-09 08:08:16
ESC/Back
Advanced Comm
Comm.
Real-time monitor
Retrieve IP mode
network Interface
ServerIP
Device IP
Subnet mask
Gateway
DNS
Com
Limit
Static
RJ45





OA1000 Series Multimedia fingerprint terminal

Installation Step
1
Drill holes in the wall follow the hole position
on back panel
2
Install and fix back panel, connect related
cables
3
Attach access control reader
Installation Diagram
Wiring Instruction
Important notice: Please follow the wiring diagram as it is displayed. Damaged products
diagram as it is displayed. Damaged products due to improper wiring are not covered under
the product warranty.
Please refer to the disk for detail
Connection Diagram
Description
Wiegand D0 Input
Wiegand D1Input
GND
Trigger Relay2
Trigger Relay1
Trigger input
GND
Wiegand
Input
Function
GND
GND
Door open
Sensor
Exit Button
PIN
RS232T
RS232R
Power
GND
DC12V
GND
RS485(B-)
RS485(A+)
(Red/Black)
Function Description
Data
communication
PIN
NO1
COM1
GND
NC1
Function Description
Wiegand
Output
Wiegand D1 Output
Wiegand D0 Output
Relay1
PIN
Trigger Output
BELL+(5V)
NO2
COM2
BELL-
GND
NC2
PIN
Function Description
GND
Relay2
Door
Bell
Without
Power
With
Power
All manuals and user guides at all-guides.com
  • Page 1 1
  • Page 2 2

Anviz OA1000 Series Quick start guide

Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI