Intermec
External Keyboard
P/N 1-960459-00
Edition 1
January 1999
Installation & Operation
Intermec External Keyboard – Installation & Operation Ed. 1
1
Chapter 1
The External Keyboard (part number 1-200591-02) is an RS 232C
keyboard intended for connection to the present range of Intermec
Fingerprint-compatible EasyCoder printers, i.e.:
EasyCoder 201 IIS, E, SA
EasyCoder 401, 401 LL
EasyCoder 501S, E, SA, XP
EasyCoder 601S, E, XP
The keyboard uses the following communication parameters:
Interface: RS 232C
Baud rate: 9600
Parity: None
Character length: 8
Stop bits: 1
The keyboard's communication cable is fitted with a female DB25
connector at the printer end and a mini-DIN connector at the
keyboard end. Connect the cable between an RS 232C serial port on
the printer (usually "uart1:") and the outer one of the two connectors
on the keyboard (the inner one is used for programming, see below).
Note that the keyboard requires +5V (42 mA) from the printer,
which in some cases must be enabled by a strap on the CPU-board
or interface board, see the Technical Manual or Installation &
Operation manual for the printer model in question.
The keybord has a standard U.S. layout, but is fully programmable
using special software (see below).
In addition to the standard keys, the keyboard has 32 free keys with
clear tops and 16 keys with blind tops, that can be programmed for
user applications. The blind tops can be replaced by clear ones and
the tops of the lower part of the keyboard can be moved so as to adapt
the keyboard for various national standards.
Programming software for Microsoft DOS and various versions of
Microsoft Windows are available free of charge at http://
www.tipro.si/Technical.htm (MIDDOS, MIDWIN, and
MIDWINNT). You will also need a PC-to-keyboard cable from
Intermec. The PC must have a PS2 keyboard connection.
Information in this manual is subject to change without prior notice
and does not represent a commitment on the part of Intermec
Printer AB.
© Copyright Intermec Printer AB, 1999. All rights reserved.
Published in Sweden.
EasyCoder and Fingerprint are registered trademarks of Intermec
Technologies Corp.
Application of Use
Intermec External Keyboard
Installation & Operation
Edition 1, January 1999
Part No. 1-960449-00
Communication
Programming
1. Description
Intermec External Keyboard – Installation & Operation Ed. 1
2
Chapter 2
The keyboard has 4 modes or layers:
L1 Unshifted
L2 Ctrl
L3 Shifted
L4 Caps Lock (deactivated by the Unlock key)
The selected layer is indicated by a control lamp on the layer
indicator panel.
When a key is pressed, the keyboard transmits an ASCII character
to the printer. The character is processed in regard of any NASC and
MAP statements (see Intermec Fingerprint manuals) and, in case of
printable data, produces a character according to the selected
character set.
On the pages that follow, the ASCII characters in decimal format
for each key and mode combination are shown. Bold characters
indicate printable characters (ASCII 32–255 dec.) whereas italic
characters indicate non-printable control characters (ASCII 0–31
dec). Refer to the appropriate version of Intermec Fingerprint
Reference Manual for complete national character set (NASC)
tables.
Standard Layout
Q
Ta b
W E R T Y U I O P
A
Caps
Lock
S D F G H J K L :
;
{
Shift Unlock
Z X C V B N M < > ?
,./
}
[]\
`
~
Shift
Layer 2
Ctrl
Ctrl
1
!
F1
2
@
F2
3
#
F3
4
$
F4
5
%
F5
6
^
F6
7
&
F7
8
*
F8
9
(
F9
0
)
F10
-
_
F11
=
+
F12
Pg Up
Home
Pg Dn
End
InsEnter
DelShift
"
'
L1 L2 L3
Num
Lock
Caps
Lock
Scroll
Lock
L4
Esc
Layer Indicators 2 x 16 Programmable Keys (Clear Tops)
1 x 16 Programmable Keys (Blind Tops)
DisabledConnections
2. Keyboard Layout
Chapter 2 Keyboard Layout
Intermec External Keyboard – Installation & Operation Ed. 1
3
L1 Unshifted
Caps
Lock
Shift Unlock
[]
Shift
Layer 2
Ctrl
Shift
L1 L2 L3
Num
Lock
Caps
Lock
Scroll
Lock
L4
96
49
50
51
52
53
54
55
56
57
48
45
122
32
120
99
118
98
110
109
44
46
47
61
827 16
15
113
119
101
114
116
121
117
105
111
112
123
125 124
97
115
100
102
103
104
106
107
108
59 39
113
24
13
2210 11
9
127
23
Ctrl
L2 Ctrl
Caps
Lock
Shift Unlock
[]
Shift
Layer 2
Ctrl
Ctrl
Shift
L1 L2 L3
Num
Lock
Caps
Lock
Scroll
Lock
L4
187
14
18
20
19
21
6
7
24
25
17
26
26
32
24
3
22
2
14
13
12 8 27 28
29
17
23
128
18
20
25
21
9
15
16
29
30 28
1
19
4
6
7
8
10
11
12
28 27
24
13
2210 11
9
3123
Chapter 2 Keyboard Layout
Intermec External Keyboard – Installation & Operation Ed. 1
4
L3 Shifted
L4 Caps Lock
Caps
Lock
Shift Unlock
[]
Shift
Layer 2
Ctrl
Shift
L1 L2 L3
Num
Lock
Caps
Lock
Scroll
Lock
L4
126
33
64
35
36
37
94
38
42
40
41
95
90
32
88
67
86
66
78
77
60
62
63
43
827 16
15
81
87
69
82
84
89
85
73
79
80
91
93 92
65
83
68
70
71
72
74
75
76
58 34
24
13
2210 11
9
127
23
Ctrl
Caps
Lock
Shift Unlock
[]
Shift
Layer 2
Ctrl
Shift
L1 L2 L3
Num
Lock
Caps
Lock
Scroll
Lock
L4
96
49
50
51
52
53
54
55
56
57
48
45
90
32
88
67
86
66
78
77
44
46
47
61
827 16
15
81
87
69
82
84
89
85
73
79
80
91
93 92
65
83
68
70
71
72
74
75
76
59 39
24
13
2210 11
9
127
23
Ctrl
-
1
-
2
-
3
-
4
-
5
Intermec UBI EasyCoder 601 E Installation And Operation
- Type
- Installation And Operation
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Intermec EasyCoder 7421 Technical Manual
-
Intermec EasyCoder F2 Operating instructions
-
Intermec EasyCoder F4 Installation & Operation Manual
-
Intermec EasyCoder 501XP Installation & Operation Manual
-
-
-
-
-
-