Intermec EasyCoder 201II Installation And Operation

Intermec

External Keyboard

P/N 1-960459-00

Edition 1

January 1999

Installation & Operation

Intermec External Keyboard – Installation & Operation Ed. 1

1

Chapter 1

The External Keyboard (part number 1-200591-02) is an RS 232C

keyboard intended for connection to the present range of Intermec

Fingerprint-compatible EasyCoder printers, i.e.:

EasyCoder 201 IIS, E, SA

EasyCoder 401, 401 LL

EasyCoder 501S, E, SA, XP

EasyCoder 601S, E, XP

The keyboard uses the following communication parameters:

Interface: RS 232C

Baud rate: 9600

Parity: None

Character length: 8

Stop bits: 1

The keyboard's communication cable is fitted with a female DB25

connector at the printer end and a mini-DIN connector at the

keyboard end. Connect the cable between an RS 232C serial port on

the printer (usually "uart1:") and the outer one of the two connectors

on the keyboard (the inner one is used for programming, see below).

Note that the keyboard requires +5V (42 mA) from the printer,

which in some cases must be enabled by a strap on the CPU-board

or interface board, see the Technical Manual or Installation &

Operation manual for the printer model in question.

The keybord has a standard U.S. layout, but is fully programmable

using special software (see below).

In addition to the standard keys, the keyboard has 32 free keys with

clear tops and 16 keys with blind tops, that can be programmed for

user applications. The blind tops can be replaced by clear ones and

the tops of the lower part of the keyboard can be moved so as to adapt

the keyboard for various national standards.

Programming software for Microsoft DOS and various versions of

Microsoft Windows are available free of charge at http://

www.tipro.si/Technical.htm (MIDDOS, MIDWIN, and

MIDWINNT). You will also need a PC-to-keyboard cable from

Intermec. The PC must have a PS2 keyboard connection.

Information in this manual is subject to change without prior notice

and does not represent a commitment on the part of Intermec

Printer AB.

Published in Sweden.

EasyCoder and Fingerprint are registered trademarks of Intermec

Technologies Corp.

Application of Use

Intermec External Keyboard

Installation & Operation

Edition 1, January 1999

Part No. 1-960449-00

Communication

Programming

1. Description

Intermec External Keyboard – Installation & Operation Ed. 1

2

Chapter 2

The keyboard has 4 modes or layers:

L1 Unshifted

L2 Ctrl

L3 Shifted

L4 Caps Lock (deactivated by the Unlock key)

The selected layer is indicated by a control lamp on the layer

indicator panel.

When a key is pressed, the keyboard transmits an ASCII character

to the printer. The character is processed in regard of any NASC and

MAP statements (see Intermec Fingerprint manuals) and, in case of

printable data, produces a character according to the selected

character set.

On the pages that follow, the ASCII characters in decimal format

for each key and mode combination are shown. Bold characters

indicate printable characters (ASCII 32–255 dec.) whereas italic

characters indicate non-printable control characters (ASCII 0–31

dec). Refer to the appropriate version of Intermec Fingerprint

Reference Manual for complete national character set (NASC)

tables.

Standard Layout

Q

Ta b

W E R T Y U I O P

A

Caps

Lock

S D F G H J K L :

;

{

Shift Unlock

Z X C V B N M < > ?

,./

}

[]\

`

~

Shift

Layer 2

Ctrl

1

!

F1

2

@

F2

3

#

F3

4

$

F4

5

%

F5

6

^

F6

7

&

F7

8

*

F8

9

(

F9

0

)

F10

-

_

F11

=

+

F12

Pg Up

Home

Pg Dn

End

InsEnter

DelShift

"

'

L1 L2 L3

Num

Lock

Caps

Lock

Scroll

Lock

L4

Esc

Layer Indicators 2 x 16 Programmable Keys (Clear Tops)

1 x 16 Programmable Keys (Blind Tops)

DisabledConnections

2. Keyboard Layout

Chapter 2 Keyboard Layout

Intermec External Keyboard – Installation & Operation Ed. 1

3

L1 Unshifted

Caps

Lock

Shift Unlock

[]

Shift

Layer 2

Ctrl

Shift

L1 L2 L3

Num

Lock

Caps

Lock

Scroll

Lock

L4

96

49

50

51

52

53

54

55

56

57

48

45

122

32

120

99

118

98

110

109

44

46

47

61

827 16

15

113

119

101

114

116

121

117

105

111

112

123

125 124

97

115

100

102

103

104

106

107

108

59 39

113

24

13

2210 11

9

127

23

Ctrl

L2 Ctrl

Caps

Lock

Shift Unlock

[]

Shift

Layer 2

Ctrl

Shift

L1 L2 L3

Num

Lock

Caps

Lock

Scroll

Lock

L4

187

14

18

20

19

21

6

7

24

25

17

26

32

24

3

22

2

14

13

12 8 27 28

29

17

23

128

18

20

25

21

9

15

16

29

30 28

1

19

4

6

7

8

10

11

12

28 27

24

13

2210 11

9

3123

Chapter 2 Keyboard Layout

Intermec External Keyboard – Installation & Operation Ed. 1

4

L3 Shifted

L4 Caps Lock

Caps

Lock

Shift Unlock

[]

Shift

Layer 2

Ctrl

Shift

L1 L2 L3

Num

Lock

Caps

Lock

Scroll

Lock

L4

126

33

64

35

36

37

94

38

42

40

41

95

90

32

88

67

86

66

78

77

60

62

63

43

827 16

15

81

87

69

82

84

89

85

73

79

80

91

93 92

65

83

68

70

71

72

74

75

76

58 34

24

13

2210 11

9

127

23

Ctrl

Caps

Lock

Shift Unlock

[]

Shift

Layer 2

Ctrl

Shift

L1 L2 L3

Num

Lock

Caps

Lock

Scroll

Lock

L4

96

49

50

51

52

53

54

55

56

57

48

45

90

32

88

67

86

66

78

77

44

46

47

61

827 16

15

81

87

69

82

84

89

85

73

79

80

91

93 92

65

83

68

70

71

72

74

75

76

59 39

24

13

2210 11

9

127

23

Ctrl

Intermec EasyCoder 201II Installation And Operation

This manual is also suitable for

Intermec EasyCoder 201II Installation And Operation

Related papers

Other documents