AGA marvel 6GARMP Troubleshooting guide

Installaon

Operaon

and

Maintenance

Instrucons

Refrigerator / Beverage Center

Luxury Series

Pro+

6GARM

6GARMP

2

CONTENTS

Unpacking your refrigerator....................................

........

......

Removing the packaging......................

.........

............

.

........

Warranty Registraon .....................

.............

......................

Installing your refrigerator.........................

....................

.......

Selecng the locaon..........................

......................

........

Cabinet Clearances ...........................................

.........

........

Leveling legs ......................................

......................

..........

Electrical Connecon...............................

...........

..................

Using Your MicroSentry™ Control....................

.............

.......

Dimensions for glass door.....................................................

Recommended Rough in Opening Dimensions

for glass door......

...............

.................

...............................

Dimensions for glass overlay door........................................

Recommended Rough in Opening Dimensions

for glass overlay door......................

..............

.....................

Full Overlay Panel Installaon Instrucons....

.....

...........

.

....

Storage Compartment Shelving ...........................................

Wine bole shelf .................................................................

Energy Saving Tips ................................................................

Care and Cleaning .................................

.

....................

..........

Cleaning condenser air ow.........................

............

..........

Cleaning the cabinet...........................................................

Cleaning the interior......................................

...........

..........

Cleaning the shelves.............................

....................

.........

Cleaning the door gasket..............................

............

..........

Replacing the light bulb...............................

..............

.

........

Troubleshoong Guide.........................

....................

............

Obtaining Service ...............................

.........................

........

Household Product Warranty................

..............

............

.....

3

4

5

6

7

8

9

12

13

14

15

16

17

is commied to building a quality product

in an environmentally friendly manner. Our processes are ghtly

controlled and closely monitored. We have achieved cerca-

ons in ISO 9001 for quality assurance and ISO 14001 for environ-

mental management from Lloyd’s Register Quality Assurance.

UNPACKING YOUR BEVERAGE COOLER

3

Remove Packaging

Your refrigerator has been packed for shipment with all parts

that could be damaged by movement securely fastened. Cut the

banding material at the boom of the carton, unfold the carton-

ing at the boom and remove the carton from the appliance.

Remove the plasc bag, styrofoam corner posts and any tape

holding the door closed and internal components in place.

The owners manual is shipped inside the refrigerator in a plasc

bag along with the warranty registraon card.

Important

Keep your carton packaging unl your refrigerator has been

thoroughly inspected and found to be in good condion. If there

is damage, the packaging will be needed as proof of damage in

transit. Aerwards please dispose of all items responsibly in

parcular the plasc bags which can be a suocaon hazard.

If the unit was shipped or has been laying on its back for any

period of me allow the refrigerator to sit upright for a period of

at least 24 hours before plugging in. This will assure oil returns

to the compressor. Plugging the refrigerator in immediately may

cause damage to internal parts.

It is important you send in your warranty registraon card im-

mediately aer taking delivery of your refrigerator or you can

register online at www.agamarvel.com.

The following informaon will be required when registering your

unit.

Model Number

Serial Number

Date of Purchase

Dealer’s name and address

The model number and serial number can be found on the se-

rial plate which is located inside the refrigerator on the le side

toward the top of the liner. See Figure 1.

Warranty Registraon

Help Prevent Tragedies

Child entrapment and suocaon are not problems of the past.

Junked or abandoned refrigerators are sll dangerous - even if

they sit out for “just a few days”.

If you are geng rid of your old refrigerator, please follow the

instrucons below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take o the doors or remove the drawers.

• Leave the shelves in place so children may not easily climb

inside.

Important Safety Instrucons

Warnings and safety instrucons appearing in this guide are not

meant to cover all possible condions and situaons that may

occur. Common sense, cauon, and care must be exercised when

installing, maintaining, or operang this appliance.

Note to Customer

This merchandise was carefully packed and thoroughly inspected

before leaving our plant. Responsibility for its safe delivery

was assumed by the retailer upon acceptance of the shipment.

Claims for loss or damage sustained in transit must be made to

the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFAC-

TURER - FILE THE CLAIM WITH THE RETAILER.

Figure 1

Recognize Safety Symbols,

Words, and Labels.

WARNING-

Hazards or unsafe pracces which could result in

personal injury.

CAUTION-Hazards or unsafe pracces which could result in

personal injury or property or product damage.

NOTE-Important informaon to make a problem free installa-

on.

NOTE

INSTALLING YOUR BEVERAGE COOLER

Select Locaon

The proper locaon will ensure peak performance of your ap-

pliance. We recommend a locaon where the unit will be out

of direct sunlight and away from heat sources. To assure your

product performs to specicaons the recommended installaon

locaon temperature range is from 65 to 80°F (18 to 27°C) for

indoor built in units, 65 to 90°F (18 to 32°C) for indoor freestand-

ing units.

Cabinet Clearance

Venlaon is required from the boom front secon of the unit.

Keep this area open and clear of any obstrucons. Adjacent

cabinets and counter top can be installed around the unit as long

as the grille and door access remain unobstructed.

4

Leveling Legs

Front Toe Grille,

keep this area

open.

Front Grille

Do not obstruct the front grille. The openings within the front

grille allow air to ow through the condenser heat exchanger.

Restricons to this air ow will result in increased energy usage

and loss of cooling capacity. For this reason it is important this

area to not be obstructed and the grille openings kept clean.

AGA MARVEL does not recommend the use of a custom made

grille as air ow may be restricted because of inadequate open-

ings. (See Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the unit should

be set so the unit is rmly posioned on the oor and level

from side to side and front to back. The overall height of your

Marvel refrigerator may be adjusted from 33-7/8” (86.1cm) with

the leveling legs turned in, and up to 34-3/4” (88.3cm) with the

leveling legs extended.

To adjust the leveling legs, place the refrigerator on a solid

surface and protect the oor beneath the legs to avoid scratch-

ing the oor. With the assistance of another person, lean the

refrigerator back to access the front leveling legs. Raise or lower

the legs to the required dimension by turning the legs. Repeat

this process for the rear by lng the refrigerator forward using

cauon. On a level surface check the refrigerator for levelness

and adjust accordingly.

The front grille (toe grille) screws may be loosened and the grille

adjusted to the desired height. When adjustment is complete

ghten the two toe grille screws. (See Figure 4).

Rear leveling legs

Figure 3

Figure 2

• Do not splash or spray water from a hose on the refrigera-

tor. Doing so may cause an electrical shock, which may

result in severe injury or death.

• This unit should not, under any circumstances, be installed

to an un-grounded electrical supply.

Electrical Connecon

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply cord that

has a three-pronged, grounded plug. It must be plugged into a

mang grounding type receptacle in accordance with the Na-

onal Electrical Code and applicable local codes and ordinances

(see Figure 5). If the circuit does not have a grounding type re-

ceptacle, it is the responsibility and obligaon of the customer to

provide the proper power supply. The third ground prong should

not, under any circumstances, be cut or removed.

Do not use an extension cord with

this appliance.

5

ELECTRICAL CONNECTION

Toe grille screw

Toe grille (Front Grille)

The unit must be installed according to your local building codes

and ordinances.

Ground Fault Circuit Interrupters (GFCI) are prone to nuisance

tripping which will cause the unit to shut down. GFCI’s are gener-

ally not used on circuits which power equipment that must run

unaended for long periods of me, unless required to meet

local building codes and ordinances.

NOTE

Figure 5

Figure 4

6

USING YOUR MICROSENTRY™ REFRIGERATOR CONTROL

Figure 6

Control

Assembly

Starng your refrigerator

Plug the refrigerator power cord into a wall outlet. Your refrig-

erator will begin cooling a few seconds aer power is applied.

If your refrigerator does not start, check that the refrigerator is

turned on and the setpoint is cold enough.

Turning your refrigerator ON or OFF

If the refrigerator is on, the refrigerator temperature will be

shown on the display. To turn the refrigerator o, press and hold

the “ON/OFF” buon for three (3) seconds. “OFF” will appear on

the display.

If the refrigerator is o. “OFF” will be shown on the display. To

turn the refrigerator on, press and hold the “ON/OFF” buon for

three (3) seconds. The refrigerator temperature will be shown on

the display.

Set temperature

To set the refrigerator temperature, press and hold the “SET”

buon. When the “SET” buon is pressed, the display will show

the set temperature. While holding the “SET” buon, press the

“WARMER” or “COLDER” buons to adjust set temperature.

Refrigerator operaon

The available temperature range of the refrigerator is 35° to 43°.

It may take up to 24 hours for your refrigerator to reach desired

temperature. This will depend on amount of content loaded and

number of door opening and closings.

For best results allow refrigerator to “pull down” to desired set

point before loading. Once contents are loaded, allow at least

48 hours for temperature to stabilize before making any adjust-

ments to the set point.

Alarms

Your MicroSentry™ refrigerator control will monitor refrigerator

funcon and alert you with a series of audible and visual alarms.

• Door Ajar Alarm: If the door has been le

open for over ve (5) minutes, the alarm

will sound in one (1) second intervals. The

display panel will ash “do” and the LED light will be a steady

amber color. This will stop as soon as the door is closed.

• Temperature Sensor Fault: If the controller

detects that a temperature sensor is

not properly funconing, a temperature

sensor alarm will sound. “E1” or “E2” will ash on

the display, and an audible alarm will sound.

Please call AGA MARVEL Customer Service or your

dealer if this error code is displayed.

Alarm Mute

Press any key to mute the audible poron of an alarm.

NOTE-This acon will only mute the alarm. If the condion that

caused the alarm connues, the alarm code will connue to ash

and will sound for 20 seconds every 60 minutes.

Light Switch

Door Switch

Control

Figure 7

close-up of

control

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

F

DIMENSIONS FOR GLASS DOOR

ROUGH IN OPENING DIMENSIONS FOR GLASS DOOR

24” (61 cm)

*24” (61 cm)

standard cabinet

depth

* Depth dimension may vary depending on

each individual installaon.

33-7/8”

(86.06 cm)

Minimum

Electrical Requirements: A grounded 115 volt, 15 amp dedicated

circuit is required.

Power outlet can be located in the back wall behind unit. Add 1”

to depth for thickness of plug, or recess outlet 1” into the wall.

Power outlet can also be installed in adjacent cabinetry with a

cutout for roung of power cord. Follow all local building codes

when installing electrical and unit.

Product weight = 130 lbs. (59.1 kg.)

23-7/8”

(60.66cm)

3” to 4”

(7.62 to 10.2cm)

7

21-1/2”

(54.61cm)

33-7/8” to 34-3/4”

(86.06 to 88.3cm)

23-5/8”

(60.0cm)

46-1/2”

(118.1cm)

25-1/2”

(64.77cm)

25-3/4”

(65.4cm)

8

DIMENSIONS FOR GLASS OVERLAY DOOR

ROUGH IN OPENING DIMENSIONS FOR GLASS OVERLAY DOOR

24” (61 cm)

*24” (61 cm)

standard cabinet

depth

* Depth dimension may vary depending on

each individual installaon.

33-7/8”

(86.06 cm)

Minimum

Electrical Requirements: A grounded 115 volt, 15 amp dedicated

circuit is required.

Power outlet can be located in the back wall behind unit. Add 1”

to depth for thickness of plug, or recess outlet 1” into the wall.

Power outlet can also be installed in adjacent cabinetry with a

cutout for roung of power cord. Follow all local building codes

when installing electrical and unit.

Product weight = 130 lbs. (59.1 kg.)

23-7/8”

(60.66cm)

3” to 4”

(7.62 to 10.2cm)

21-1/2”

(54.61cm)

33-7/8” to 34-3/4”

(86.06 to 88.3cm)

23-13/16”**

(60.48cm)

46-1/2

(118.1cm)

23-1/8”

(58.72cm)

23-7/8”**

(60.66cm)

**Dimension includes

3/4” thick overlay panel

Door should be

parallel to top

and sides of

refrigerator.

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

Step 1: Verify door alignment

Verify that the door is aligned with the cabinet prior to fabricat-

ing the custom panel. Failure to do so could result in mis-align-

ment of the custom panel with the hinge bracket. If alignment is

necessary the door may be adjusted by loosening the 2 screws

which secure the hinge adapter brackets on the top and boom

of the door and adjusng the door side to side. Use a 5/32” allen

wrench for this procedure. (See Figure 8 below). When nished

aligning the door, ghten the screws securely.

Hinge adapter brackets lo-

cated on the top and boom

of the door.

Remove the top

hinge pin to re-

move the door.

Step 2: Remove door

Remove the top hinge pin from the hinge with an 1/8” allen

wrench. Remove the door by angling the top of the door out-

ward and liing the door o the boom hinge.

(See detail in Figure 8).

Step 3: Remove gasket

Lay the door on its front being careful not to scratch it. Remove

the door gasket by peeling up and out of the channel.

Step 4: Cut overlay panel

Depending on the refrigerator model cut the overlay panel to

the dimensions shown. Use Figure 9 and Table A for glass door

models.

The non-glass, solid door, will use the same height and width di-

mensions as the glass door. The center of the solid door custom

panel will not be removed.

For overlay with lock opon panel thickness to be

3/4” (19mm) maximum to 5/8” (16mm) minimum.

Weight of the overlay panel should not exceed 20 pounds (9.1

kilograms).

9

For the door to close properly, it is necessary to maintain a

minimum space of 9/32” (7mm) between the door and cabinet

ange, (see Figure 8). This space can be adjusted by adjusng

the top and boom hinge adapter brackets.

9/32”

(7mm)

Model W H

6GARM

23-5/8”

(60.0cm)

30-3/8”

(77.17cm)

Glass Door Models and

Solid Door Models

W

H

Overlay

panel

dimensions

2-1/32”

(38.77cm)

minimum

Glass Door Models and

Solid Door Models

NOTE

Figure 8

Figure 9

Table A

10

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

Step 5: Drill hinge clearance holes in overlay panel

Set the overlay panel on the door front, align the edges, and

clamp together. Clamp the panel rmly but be careful not to

damage the door or the panel. Mark center of hinge adapter

hole on wood panel, top and boom. (See Figure 10.) Remove

wood panel from door and drill 5/16” (8mm) diameter clearance

holes into the overlay panels 3/4” (20mm) deep. These will be

clearance holes for the top and boom hinge pins.

This is also a convenient me to locate and drill the holes for

your handle. Most oen the handle is to match that of the sur-

rounding cabinetry. If your handle aaches from the back-side

of the custom panel, locate the mounng holes while the panel

is aached to the door and cabinet. Aer the panel is removed

from the door, drill the mounng holes from the front, to the

recommended diameter of the handle manufacturer. Counter

bore the back-side of the panel so the screw heads do not inter-

fere with the surface of the door.

Step 6: Drill panel mounng holes

Re-clamp the panel to the door per step 5 and drill the screw

pilot holes, located in the gasket channel, for aaching the over-

lay panel to the door. Select the size of the hole from Table B.

Be careful not to drill the pilot holes through the overlay panel,

(1/2” (12.7mm) deep for 3/4” (19mm) and 5/8” (15.7mm)

panels ).

Material Type Pilot Hole for #8 Wood Screw

Hardwood 1/8” (3.2mm) Diameter. Pilot Hole

Sowood 7/64 (2.8mm) Diameter. Pilot Hole

If your refrigerator has a door lock proceed to Step 7. If your

refrigerator does not have a door lock proceed to Step 9.

Step 7: Mark and drill lock hole (if required)

Locate and mark with a pencil the locaon of the lock hole on

the overlay panel, this is the hole in the top corner of the handle

side of the door. Remove the clamp and remove the overlay

panel from the door. On the backside of the panel where you

marked the lock locaon drill a 13/16” (20.5mm) diameter

counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a

15/32” (12.0mm) diameter hole through the overlay panel cen-

tered on the counter bore being careful not to splinter the wood

on the face side of the panel. (See Figure 11).

Step 8: Assemble the lock parts (if required)

Two (2) lock extensions are supplied with the lock. Use the lon-

ger extension for a 3/4” thick overlay panel and the shorter one

for a 5/8” thick panel. Assemble the lock extension, cam stop

washer, spring washer, and set screw to the lock as shown in

Figure 11 and 12. Install this assembly into the overlay panel and

secure with the retaining nut using a 15mm socket. Make sure

the key slot in the lock is vercal.

Overlay

panel

Door

Top hinge

adapter bracket

Hole in hinge

adapter bracket

Hole in bottom

hinge adapter bracket

NOTE

SECTION A-A

SCALE 1 : 1

LOCK

NUT

BRASS EXTENSION

CAM

PHILLIPS SCREW

13/16 COUNTER

BORE 7/16 DEEP

15/32 HOLE

3/4 INCH

WOOD PANEL

SPRING WASHER

INNER

DOOR

Figure 11

Figure 10

Glass door

shown

Table B

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

Step 9: Secure overlay panel to the door.

With the #10 wood screws provided fasten the overlay panel to

the door. (See Figure 13).

Step 10: Install lock cam (Models with locks only).

Aach the lock cam to the back of the lock assembly with the

phillips head machine screw provided. Orient the lock cam ver-

cally when installing on the lock.

Step 11: Install door gasket

Press the door gasket into the door channel. Make certain the

gasket corners are fully inserted. If applicable insert the key into

the lock and make certain the lock operates properly.

Step 12: Install the door

Install the top and boom hinge adapter bushings back into the

hinge adapters that were removed in step 6. Install the door by

reversing the procedure from step 2. Install the top hinge pin so

the screw head is ush with the top surface of the hinge. If appli-

cable insert key into lock and verify the lock cam works properly

with the catch bracket on the front of the appliance cabinet.

Clearance hole through

door gasket channel

#10 Wood Screw

Back of door

Top hinge pin

Top door hinge

adapter

Top hinge adapter

bushing

Top hinge

Boom door

hinge adapter

Boom hinge

adapter bushing

Boom hinge pin

Boom hinge

cam

11

Boom

hinge

1.234” (31.3mm)

.991” (25.2mm)

Figure 12

Figure 13

Figure 14

Right hand

hinges shown

STORAGE COMPARTMENT SHELVING

Loading Tips and Suggesons

Your product is equipped with a canlever shelf system to pro-

vide you with maximum adjustability and customizaon opons

through the purchase of aermarket shelving.

The basic cabinet comes with 3 glass shelves which can be

posioned anywhere in the cabinet. The glass half shelf allows

storage of tall boles or opened wine boles on the shelf below.

(See Figure 15). The xed wooden bole cradle at the boom of

the cabinet will hold 6 boles of wine. The wooden, boom bot-

tle cradle may be removed for storing “jug” wines. Just remove

the two (2) screws that secure the cradle to the cabinet oor.

The boles or cans on the top shelf directly under the light will

be exposed to a slightly higher temperature when the light is on.

Posion your product accordingly and REMEMBER TO TURN OFF

THE LIGHT WHEN IT IS NO LONGER NEEDED.

12

Glass

shelves

Wine bole

cradle

Tall bole

storage area

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the unit. Grasp the shelf front with both

hands, rotate the front upward and li out. (See Figure 16). To

install a shelf insert the shelf in the unit and insert the hooks into

the shelf support slots and drop the shelf down so the hooks

drop over the boom of the slots.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Grasp the shelf on

the wood front

Make sure the shelf is secure

before loading the shelf.

NOTE

Figure 15

Figure 16

13

ENERGY SAVING TIPS

The following suggesons will minimize the cost of

operang your refrigeraon appliance.

1. Do not install your appliance next to a hot appliance, (cook-

er, dishwasher, etc.). heang air duct, or other heat sources.

2. Install product out of direct sunlight.

3. Assure the toe grille vents at front of unit beneath door is

not obstructed and kept clean to allow venlaon for the

refrigeraon system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When inially loading your new product, or whenever large

quanes of warm contents are placed within refrigerated

storage compartment, minimize door openings for the next

12 hours to allow contents to pull down to compartment

set-point temperature.

6. Maintaining a relavely full storage compartment will re-

quire less appliance run me than an empty compartment.

7. Assure door closing is not obstructed by contents stored in

your appliance.

8. Allow hot items to reach room temperature before placing

in product.

9. Minimize door openings and duraon of door openings.

10. Use the warmest temperature control set-point that meets

your personal preference and provides the proper storage

for your stored contents.

11. Minimize use of display lighng opon on glass door

products, (light stays on with door closed).

12. When on vacaon or away from home for extended pe-

riods, set the appliance to warmest acceptable tempera-

ture for the stored contents.

13. Set the control to the “o” posion if cleaning the unit

requires the door to be open for an extended period of

me.

14. Annually clean condenser heat exchange coil located

in machine compartment underneath unit, (see “Care

and Cleaning” page 14).

Wine Bole Shelf

Underneath the glass on both full width shelves are the wine

bole shelves. Simply remove the glass to store your boled

wine. (See Figures 17 and 18).

The wine shelf holds 6 boles of wine. Keep wines that you plan

to use for everyday drinking and entertaining on the front half

of the shelf. Because of the lower temperature of the refrigera-

tor the wine shelf may not be conducive to long term storage of

your wine.

Wine shelf

underneath glass

Figure 17

Figure 18

Wine Shelf

14

CARE AND CLEANING OF YOUR BEVERAGE AND WINE REFRIGERATOR

Condenser Cleaning

Disconnect the power cord before cleaning the condenser.

The tube and wire condenser underneath the cabinet does

not require frequent cleaning; however, sasfactory cooling

depends on adequate venlaon over this heat exchanger. It is

recommended to annually clean the condenser by brushing and

vacuuming. Access the condenser, from the front of the unit by

removing the toe grille. (See Figure 18). Remove the 2 screws

holding the toe grille in place with a phillips screwdriver. The

condenser is located 2-1/2” (6.4cm) behind the toe grille on the

le side of the cabinet. We recommend using a refrigerator coil

cleaning brush to loosen the dust and dirt, then vacuuming.

Be sure that nothing obstructs the required air ow openings in

front of the cabinet. (See page 4).

Cabinet

The painted cabinet can be washed with mild soap and water

and thoroughly rinsed with clear water. NEVER use abrasive

scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do NOT

use an abrasive cleaner, solvent, polish cleaner or undiluted

detergent.

Shelving

The shelves may be cleaned with mild soap and water and a

so cloth. Do NOT use any abrasive cleaners. The glass may be

removed for easier cleaning.

Glass Door

Use a glass cleaner or mild soap and water and so cloth to

clean the glass door model. Do NOT use any abrasive cleaners.

Door Gasket

The vinyl gasket may be cleaned with mild soap and water, a bak-

ing soda soluon or a mild scouring powder.

Light Bulb Replacement

DISCONNECT THE POWER CORD BEFORE ATTEMPTING LIGHT

BULB REPLACEMENT. Failure to do so may result in an electrical

shock that could severely injure you.

The 6GARM uses one, 15 wa incandescent light bulb to il-

luminate the interior of the refrigerator. The light bulb is a

very reliable electrical component, but should it not funcon

properly, please call the dealer where you purchased your

refrigerator for a replacement light bulb. Use only an origi-

nal equipment light bulb from your dealer or AGA MARVEL.

Do NOT under any circumstance use a light bulb that exceeds 15

was!

To replace the light bulb, disconnect power to the unit. Unscrew

the old light bulb located behind the display housing at the top

of the unit. Set the old light bulb aside. Screw the new light

bulb into place. Reconnect power to the unit. Check to see if the

light bulb operates properly to complete the installaon.

The light bulb is not covered by your warranty. A replacement

bulb can be obtained from your dealer or from AGA MARVEL.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as possible.

Minimize the number of door openings while the power is o so

as not to adversely aect the unit’s temperature.

Toe grille screw

Condenser is

behind toe grille

on le side of

cabinet

Toe grille (Front Grille)

Figure 18

TROUBLESHOOTING YOUR BEVERAGE AND WINE REFRIGERATOR

Problem Possible Cause Remedy

Unit not cold enough

Adjust temperatures (See “Set Tempera-

tures” on page 6)

• Control set too warm

• Content temperature not stabilized.

• Excessive usage or prolonged door

openings.

• Airow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Allow 24

hours for temperature to stabilize.

• Allow temperature to stabilize for at

least 24 hours.

• Airow must not be obstructed to

front grille. See “clearances” on

page 4.

• Check door alignment and/or replace

door gasket.

Unit too cold

Adjust temperatures (See “Set Tempera-

tures” on page 6)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer. (See

page 6, “set temperature”). Allow 24

hours for temperature to stabilize.

• Check door alignment and/or replace

door gasket.

No interior light. • Failed light bulb • Replace light bulb, see page 14.

Light will not go out when door is closed • Door not acvang light switch.

• Display light is turned on.

• Unit not level, level unit, (See page 4,

“leveling legs”)

• Verify the door is aligned properly,

refer to page 9 for instrucons.

• Turn o display light, shut door.

Noise or Vibraon • Unit not level • Level unit, see “Leveling Legs” on

page 4.

Unit will not run. • Unit turned o

• Power cord not plugged in.

• No power at outlet.

• Turn unit on. See “Starng your re-

frigerator” on page 6.

• Plug in power cord.

• Check house circuit.

Before you call for service

If the unit appears to be malfunconing, read through this

manual rst. If the problem persists, check the troubleshoong

guide below. Locate the problem in the guide and refer to the

cause and its remedy before calling for service. The problem may

be something very simple that can be solved without a service

call. However, it may be required to contact your dealer or a

qualied service technician.

Electrocuon Hazard - Never aempt to repair or perform

maintenance on the unit unl the main electrical power has

been disconnected. Turning the units control “o” does not

remove electrical power from the units wiring.

15

16

OBTAINING SERVICE

If Service is Required:

• If the product is within the rst year warranty period please

contact your dealer or call AGA MARVEL Customer Service

at 800.223.3900 for direcons on how to obtain warranty

coverage in your area.

• If the product is outside the rst year warranty period, AGA

MARVEL Customer Service can provide recommendaons of

service centers in your area. A lisng of authorized service

centers is also available at www.agamarvel.com under the

service and support secon.

• In all correspondence regarding service, be sure to give the

model number, serial number, (located on your refrigerator’s

serial plate) and proof of purchase.

• Try to have informaon or descripon of nature of the prob-

lem, how long the unit has been running, the room tempera-

ture, and any addional informaon that may be helpful in

quickly solving the problem.

• Table C is provided for recording pernent informaon re-

garding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Model Number

Date Warranty Card Sent (Must be

within 10 days of purchase).

Table C

Parts or Service

Not Supplied or Designated by AGA MARVEL

The above warranes also do not apply if:

• The original bill of sale, deliver date, or serial number can-

not be veried.

• Defecve parts are not returned for inspecon if so request-

ed by AGA MARVEL.

• The refrigeraon equipment is not in the possession of the

original end use purchaser.

The warranes set forth herein are the only warranes extended

by AGA MARVEL. Any implied warranes, including the implied

warranty of merchantability, are limited to the duraon of these

express warranes. In no event shall AGA MARVEL be liable for

any consequenal or incidental damages or expenses resulng

from breach of these or any other warranes, whether express

or implied.

Some states do not allow the exclusion or limitaon of conse-

quenal damages or a limitaon on how long an implied war-

ranty lasts, so the above exclusion or limitaon may not apply

to you. This warranty gives you specic legal rights and you may

have other rights that may vary from state to state.

No person, rm, or corporaon is authorized to make any other

warranty or assume any other obligaon for AGA MARVEL.

These warranes apply only to products used in any of the y

states of the United States and the District of Columbia.

To obtain performance of this warranty, report any defects to:

1260 E. VanDeinse St.

Greenville MI 48838

Phone: 800.223.3900

Enre Product

Limited One Year Parts and Labor Warranty

AGA MARVEL warrants that it will supply all necessary parts and

labor to repair or replace in the end user’s home or oce, any

component which proves to be defecve in material or work-

manship, subject to the condion and exclusions stated below,

for a period of one year from the date of purchase by the end

user.

Addional Second Through Fih Year

Limited Parts Only Warranty

During the four years following expiraon of the one year limited

warranty, AGA MARVEL will supply replacement parts for the

hermecally sealed refrigeraon system which consists of the

compressor, condenser, drier, connecng tubing and the evapo-

rator that are proven to be defecve due to workmanship or

materials subject to the condions and exclusions below.

The above warranes do not cover:

• Shipping costs of replacement parts or returned defecve

parts.

• Customer educaon or instrucons on how to use the appli-

ance.

• Any content loss due to product failure.

• Removal or installaon of product.

Nor do the above warranes cover failure of this product or its

components due to:

• Transportaon or subsequent damages.

• Commercial use or use other than normal household or

small oce.

• Improper installaon, misuse, abuse, accident or alteraon,

use of wiring not conforming to electrical codes, low or high

voltages, failure to provide necessary maintenance, or other

unreasonable use.

HOUSEHOLD PRODUCT WARRANTY

17

Page is loading ...

All specicaons and product designs subject to change without noce. Such revisions do not entle the

buyer to corresponding changes, improvements, addions, replacements or compensaon for previously

purchased products.

www.agamarvel.com

1260 E. VanDeinse St.

Greenville MI 48838

800.223.3900

41012375-EN Rev A

4/1//2011

Page is loading ...

AGA marvel 6GARMP Troubleshooting guide

This manual is also suitable for

AGA marvel 6GARMP Troubleshooting guide

in other languages

Related papers

Other documents